Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “resuspension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Radionuclide surrogate aerosolization, resuspension and suppression in hazardous situations

Radioactive fire following nuclear accidents causes resuspension of radioactive contamination that can spread over large areas. Although many papers focus on particle deposition and resuspension, a limited number of studies model its suppression. Even less data is available for the comparison of emissions across particle size, surface, and mode of resuspension. In this study, cerium dioxide surrogate for internal hazards such as radionuclide particle matter was aerosolized into a large chamber and subsequently resuspended after sedimentation. Resuspension was induced by common modes of human movement including walking, wind, and driving on common surfaces including polyvinyl chloride (PVC), artificial grass (turf), and concrete in a 5.8 m long, 3.7 m wide and 3 m high tent. The resuspension was experimentally measured for two particle sizes (1 and 10 μm) at three different heights (0.3 m, 1.2 m, and 2.4 m) and compared across size, surface, and mode of resuspension. Particle size distribution was measured using an aerodynamic particle sizer and the resuspended particles were collected with the wetted wall cyclone aerosol collector and quantitated using inductively coupled plasma mass spectrometry. The testing was repeated with the F-500 fire retardant application to study its effect on resuspension. In this study, artificial grass flooring was found to generate the most resuspension, with walking on turf for the 1 μm particle testing yielding the highest factor overall. Concrete had the lowest resuspension, showing variations in the size distribution of aerosol as a function of height from the source resuspension factors. The application of fire retardant was found to significantly reduce surrogate resuspension, regardless of resuspension method or testing surface. Here, the results provide impactful information regarding the different modes of resuspension including human transport (walking and driving) and wind for the resuspension of radionuclide surrogate particles deposited onto common surfaces and the effect of fire retardant application on their resuspension, leading to higher levels of safety for nuclear energy plants and facilities.

42 ENGINEERING↗
DOE OSTI2020

Surrogate Suspension-Resuspension Study

The objective of this study was to conduct a series of tests looking at the deposition and resuspension of aerosol particles deposited onto multiple representative substrate surfaces for a range of particle sizes under varying environmental conditions. The benefit of this study is to provide additional insight into the understanding of early time resuspension from different mechanisms and compare to existing literature. The resuspension methods utilized in this study were full-scale and the substrates were representative of real- world ground level conditions. Multiple experiments were conducted to assess the impact on resuspension from the varying substrates and mechanisms. The results of this study show variations in the size distribution of aerosol as a function of height from the source resuspension factors. Additionally, the aerosolized mass concentration and resuspension factor were evaluated. The maximum resuspension factor was found to be on the order of 10 -4 m -1 which is higher than most resuspension factors found in literature but represents idealized conditions due to the well constrained experimental setup.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Particle resuspension: Challenges and perspectives for future models

Using what has become a celebrated catchphrase, Philip W. Anderson once wrote that “more is different” (Science, Vol. 177, Issue 4047, pp. 393–396, 1972). First formulated in the context of condensed matter, this statement carries far beyond the sole limits of solid-state physics. It emphasizes that collective behavior can be more than the mere sum of what happens for elementary constituents or the mere collation of the evolution of each degree of freedom. Said otherwise, complex phenomena can arise out of the interplay between multiple sub-phenomena each of which can be relatively simple. The process of particle resuspension, in which discrete particles adhering on a surface are pulled off and carried away by a fluid flow, is another example involving a web of phenomena pertaining to fluid mechanics, particle dynamics and interface chemistry whose cross-effects create an intricate topic. The purpose of this review is to analyze the physics at play in particle resuspension in order to bring insights into the rich complexity of this common but challenging concern. Following the more-is-different vision, this is performed by starting from a range of practical observations and experimental data. We then work our way through the investigation of the key mechanisms which play a role in the overall process. In turn, these mechanisms reveal an array of fundamental interactions, such as particle–fluid, particle–particle and particle–surface, whose combined effects create the tapestry of current applications. At the core of this analysis are descriptions of these physical phenomena and the different ways through which they are intertwined to build up various models used to provide quantitative assessment of particle resuspension. The physics of particle resuspension implies to hold together processes occurring at extremely different space and time scales and models are key in providing a single vehicle to lead us through such multiscale journeys. This raises questions on what makes up a model and one objective of the present work is to clarify the essence of a modeling approach. In spite of its ubiquitous nature, particle resuspension is still at the early stages of developments. Many extensions need to be worked out and revisiting the art of modeling is not a moot point. The need to consider more complex objects than small and spherical particles and, moreover, to come up with unified descriptions of mono- and multilayer resuspension put the emphasis on solid model foundations if we are to go beyond current limits. Further, this is very much modeling in the making and new ideas are proposed to stimulate interest into this everyday but challenging issue in physics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

A Review of the Resuspension of Radioactively Contaminated Particles by Vehicle and Pedestrian Traffic—Current Theory, Practice, Gaps, and Needs

Here, the resuspension of radioactively contaminated particles in a built environment, such as from urban surfaces like foliage, building exteriors, and roadways, is described empirically by current plume and dosimetry models used for hazard assessment and long-term risk purposes. When applying these models to radiological contamination emergencies affecting urban areas, the accuracy of the results for recent contamination deposition is impacted in two main ways. First, the data supporting the underlying resuspension equations was acquired for open, quiescent conditions with no vehicle traffic or human activities, so it is not necessarily representative of the urban environment. Second, mechanical disturbance by winds in urban canyons and during emergency operations caused by vehicle traffic and human activities are not directly considered by the equations. Accordingly, plume and dosimetry models allow the user to input certain compensating values, but the models do not necessarily supply users instructions on what values to use. This manuscript reviews the available literature to comprehensively and consistently pool data for resuspension due to mechanically induced resuspension applicable to urban contamination. Because there are few studies that directly measured radioactive resuspension due to vehicles and pedestrians, this review novelly draws on a range of other studies involving non-radioactive particles, ranging from outdoor air pollution emissions to indoor allergen transport. The results lead to tabulated, recommended values for specific conditions in the emergency phase to help users of plume and dosimetry models maintain the conservativeness needed to properly capture the potential radiation dose posed by mechanically induced resuspension. These values are of benefit to model users until better data are available. The results also suggest the types of data that may result in improved plume and dose modeling.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2020

Impact of the adhesion-force lever-arm “a” on the Rock ‘n’ Roll resuspension model and how to compute it from contact mechanics

The paper proposes a methodology to fill a gap in the context of mechanistic particle resuspension models related to the adhesion and lift force lever arms ( a ): to date, only one experimental observation exists from a centrifuge experiment with a specific particle/surface pair which found r P / a = 100 and assumed that the contact points were symmetric with respect to the particle center. However, the Reeks and Hall’s (2001) model is highly sensitive to this parameter, which therefore cannot be used as-is for different particle diameters or materials. This paper proposes a methodology to compute the adhesion and lift force lever arms ( a A and a L , respectively) based on Atomic Force Microcopy (AFM) surface roughness measurements and contact mechanics arguments. In practice, a spherical, perfectly smooth particle is brought in contact (computationally) with the measured surface roughness and is then rotated by the point of contact to determine the two or more asperities over which the particle would sit on the surface. A method to compute the asperity radius of curvature is devised to compute the asperity deformation and the correct partitioning of the total deformation between the particle and the asperity is presented. For the glass surface under consideration, the asperity deformation was negligible, i.e., it was below the van der Waals radius, which is the limit of applicability of contact mechanics. The Reeks and Hall’s (2001) model is then extended to account for the joint probability of a A and a L . Significant differences in particle resuspended after a day in common atmospheric conditions are found between the approach that uses the lever-arm distributions or their mean values. Also, important differences are found when comparing the lever-arm distribution and r P / a = 100. Hence, one should be cautious of using r P / a = 100 for surface/particle pairs differing from those in the original study. Finally, limits of applicability of the theories used are presented together with considerations regarding how to extend the method to non-spherical particles and different materials.

42 ENGINEERING↗
DOE OSTI2024

Trends of Sediment Resuspension and Budget in Southern Lake Michigan Under Changing Wave Climate and Hydrodynamic Environment

Sediment suspension and transport driven by waves and currents play a significant role in both the ecological and physical environments of large lakes. Lake Michigan has faced a rapidly increasing water level associated with intensified wind waves in the past decade. To investigate the spatiotemporal characteristics of suspended sediment concentration (SSC) and associated coastal sediment budgets in southern Lake Michigan, a 30-year (1991–2020) hindcast was performed using a coupled wave-current-sediment model (SWAN-FVCOM-CSTMS). We found that in southern Lake Michigan, the basin-wide mean SSC increased, and the coastal sediment loss accelerated dramatically, corresponding with intensified waves, currents and lake water level rises over the past decade. The basin-wide mean SSC, coastal sediment loss, wave height, wind speed, current speed, and water level in southern Lake Michigan are highly correlated. Spatially, the results reveal decreases in coastal SSC and sediment loss in the western portion of the southern basin, while the eastern sectors show an increase in both metrics. This reflects a clear shift in the wave climate and hydrodynamic environment. The alterations in long-term coastal sediment budgets imply that considerable shoreline transformations are being influenced by modifications in the wave climate. Understanding the spatiotemporal characteristics of SSC and coastal sediment budgets is crucial for strategic water resource management and coastal infrastructure planning.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Compositing and Characterization of SE Quadrant Waste Exemplars

This report outlines the experimental investigation and characterization of transport properties in Hanford SE quadrant High-Level Waste (HLW). The goal of the study was to establish baseline behaviors of bulk composite rheology and settling characteristics to facilitate waste treatment process design for the Waste Treatment and Immobilization Plant (WTP) and avoid waste conditions and properties favorable to bubble cascade gas release events. The study focused on two major objectives: 1) identifying, obtaining, and preparing relevant Hanford tank waste samples for evaluation and 2) quantifying the “as-received” rheology and transport properties of the samples. Twenty-three centrifuged core segments originating from tanks AN-101, AN-106, and AW-105 were selected based on compositional relevance to SE quadrant PUREX cladding waste. These materials were composited into five waste composites enriched with target analytes: aluminum (Al), iron (Fe), phosphate (PO 4 ), uranium (U), and zirconium (Zr). Physical property and transport testing examined particle size distributions, bulk densities, settling behaviors, rheological properties, shear strengths, and just-suspended mixing speeds (NJS). Testing revealed two distinct composite classifications based on rheological characteristics: non-Newtonian composites (Fe and PO 4 ) and Newtonian composites (Al, U, and Zr). The Fe and PO 4 composites exhibited slow settling rates and reduced mobilization proclivity, attributable to strong particle-particle interactions and the formation of yield structures within non-Newtonian slurries. In contrast, the Al, U, and Zr composites displayed rapid settling and dense compaction behaviors, indicative of minimal structuring and interactions. Shear strengths for all composites were generally low relative to prior studies of SE quadrant waste, with only the U composite showing elevated strength approaching values reported in previous literature. Repeat shear strength measurements revealed contributions from dense granular material in the U composite and stronger cohesive properties in the Al composite. Settling data highlighted hindered settling behavior, with rates falling more than one order of magnitude below estimates based on Stokes’ law and rate decreasing as composite UDS content increased. NJS testing demonstrated different mobilization behaviors between cohesive and granular composites. The Fe composite required the highest mixing rate for resuspension, while the Al composite was the easiest to resuspend. Comparison of measured NJS against predictions made using the Zwietering correlation suggests non-Newtonian behavior alters resuspension mechanics, rendering non-Newtonian systems more stable against resuspension lift forces relative to their granular counterparts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Modeling sediment diagenesis processes on riverbed to better quantify aquatic carbon fluxes and stocks in a small watershed of the Mid-Atlantic region

Background: Despite the widely recognized importance of aquatic processes for bridging gaps in the global carbon cycle, there is still a lack of understanding of the role of riverbed processes for carbon flows and stocks in aquatic environments. Here, we added a sediment diagenesis and sediment carbon (C) resuspension module into the SWAT-C model and tested it for simulating both particulate organic C (POC) and dissolved organic C (DOC) fluxes using 4 years of monthly observations (2014–2017) in the Tuckahoe watershed (TW) in the U.S. Mid-Atlantic region. Results: Sensitivity analyses show that parameters that regulate POC deposition in river networks are more sensitive than those that determine C resuspension from sediments. Further analyses indicate that allochthonous contributions to POC and DOC are about 36.6 and 46 kgC ha –1 year –1 , respectively, while autochthonous contributions are less than 0.72 kgC ha –1 year –1 for both POC and DOC (less than 2% of allochthonous sources). The net deposition of POC on the riverbed (i.e., 11.4 kgC ha –1 year –1 ) retained ca. 31% of terrestrial inputs of POC. In addition, average annual buried C was 0.34 kgC ha –1 year –1 , accounting for only 1% of terrestrial POC inputs or 3% of net POC deposition. The results indicate that about 79% of deposited organic C was converted to inorganic C (CH 4 and CO 2 ) in the sediment and eventually released into the overlying water column. Conclusion: This study serves as an exploratory study on estimation of C fluxes from terrestrial to aquatic environments at the watershed scale. We demonstrated capabilities of the SWAT-C model to simulate C cycling from uplands to riverine ecosystems and estimated C sinks and sources in aquatic environments. Overall, the results highlight the importance of including carbon cycle dynamics within the riverbed in order to accurately estimate aquatic carbon fluxes and stocks. The new capabilities of SWAT-C are expected to serve as a useful tool to account for those processes in watershed C balance assessment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Hurricanes and turbulent floods threaten arsenic-contaminated coastal soils and vulnerable communities

Coastal environments, particularly those adjacent to Superfund sites, are at increased risk of contaminant release during natural disasters, posing serious threats to nearby communities. To investigate this issue, we employed an advanced laboratory flood simulator to impose arsenic-contaminated sediments to turbulent flooding events. We further monitored changes in arsenic collocation and solid-phase speciation using advanced synchrotron radiation-based techniques to understand the impacts of flooding on arsenic mobility. Our results demonstrate that turbulent conditions significantly enhance the resuspension of arsenic-rich sediments, resulting in increased arsenic release into the water. This mobilization is driven by the erosion of the reduced sediments and the redox-mediated transformation and dissolution of Fe and Mn (oxyhydr) oxides, which promote the release of As(III). We found that arsenic speciation on resuspended particles is closely tied to shear stress, with As(V) prevailing at low stress and the more toxic As(III) dominating at higher stress levels. In the post-erosion phase, solid-phase As(III) decreased while dissolved As(III) increased, indicating ongoing desorption. The persistence of multiple arsenic species on resuspended particles marks them as potential long-range transport vectors. Thus, the environmental impact of flooding and sediment resuspension extends beyond the event itself, raising longer-term concerns for arsenic mobility. Our comprehensive geospatial analysis revealed substantial overlap between arsenic-contaminated soils and regions at high risk of flooding and hurricanes across the conterminous United States. This overlap disproportionately impacts economically disadvantaged and marginalized communities. Approximately 40 million Americans reside within 10 kilometers of these high-risk contaminated zones, with nearly 28 million exposed to hurricane threats and around 18 million vulnerable to flooding risks. Alarmingly, over 40% of those affected by hurricanes and 33% of those impacted by flooding belong to underrepresented minority and low-income populations. These findings highlight the urgent need for targeted mitigation strategies to protect public health and address environmental justice concerns.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Using a coupled dispersion model to estimate depletion of a tritium oxide plume by a forest

Tritium processing facilities may release tritium oxide (HTO) to the atmosphere which poses potential health risks to exposed co-located workers and to offsite individuals. Most radiological consequence analyses determine HTO dose by applying Gaussian plume models to simulate the transport of HTO. Within these models, deposition velocity is used to assess the sum of all deposition processes acting on the plume. While this may account for vegetative and soil uptake or respiration processes, it may currently lack inclusion of the complex interactions within heterogeneous forested environments. In this complex morphology, dispersion patterns are significantly altered by changing flow regimes above and below the forest canopy and by the transfer of plume material across the canopy boundary. To determine the effects of a heterogeneous forest canopy on an airborne HTO plume, a Gaussian plume model coupled with an advection-diffusion plume model was applied to estimate transport in the free atmosphere above the forest and within the forest canopy and understory. During 2012, wind speed and wind direction measurements taken at 5 heights, ranging from 2-m to 28-m, on an instrumented meteorological tower located in a loblolly pine forest at the Department of Energy (DOE) Savannah River Site (SRS), near Aiken, SC. From these measurements, model predictions were made over a full spectrum of meteorological conditions. Deposition and resuspension velocities were calculated based on the model-predicted flux of plume material across the top of the forest canopy. Additionally, net deposition velocity of the plume material was calculated as the difference between the deposition and resuspension velocities. The 1st and 5th percentile net deposition velocities were estimated to be 0.7 cm s-1 and 1.2 cm s-1, respectively.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2020

Ejection of Dust From the Ocean as a Potential Source of Marine Ice Nucleating Particles

Oceans are, generally, relatively weak sources of ice nucleating particles (INPs). Thus, dust transported from terrestrial regions can dominate atmospheric INP concentrations even in remote marine regions. Studies of ocean-emitted INPs have focused upon sea spray aerosols containing biogenic species. Even though large concentrations of dust are transported over marine regions, resuspended dust has never been explicitly considered as another possible source of ocean-emitted INPs. Current models assume that deposited dust is not re-emitted from surface waters. Our laboratory studies of aerosol particles produced from coastal seawater and synthetic seawater doped with dust show that dust can indeed be ejected from water during bubble bursting. INP concentration measurements show these ejected dust particles retain ice nucleating activity. Doping synthetic seawater to simulate a strong dust deposition event produced INPs active at temperatures colder than -13 °C and INP concentrations one to two orders of magnitude greater than either lab sea spray or marine boundary layer measurements. The relevance of these laboratory findings is highlighted by single particle composition measurements along the Californian coast where at least 9% of dust particles were mixed with sea salt. Additionally, global modeling studies show that resuspension of dust from the ocean could exert the most impact over the Southern Ocean, where ocean-emitted INPs are thought to dominate atmospheric INP populations. More work characterizing the factors governing the resuspension of dust particles is required to understand the potential impact upon clouds.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Deposition Modeling Updates for a Vertical System

This report provides deposition modeling updates and results for a vertical spent nuclear fuel (SNF) storage system. The vertical storage system was the NAC International’s Modular, Advanced Generation, Nuclear All-purpose STORage System (MAGNASTOR®). The updates to the model included running a turbulent model sensitivity study and incorporating droplet evaporation into the deposition model for the MAGNASTOR®. In addition to the updates to the vertical MAGNASTOR system this report discusses the topic of particle resuspension and future work related to looking at resuspension in both a vertical and horizontal storage system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Review of particle deposition to and removal from clothing, skin, and hair after a radioactive airborne dispersal event

Explosive Radiological Dispersal Devices (RDD) – aka dirty bombs – are seen as a credible method to carry out a radiological terror attack. After exploding a radioactive source, the radionuclide-laden plume will be blown downwind of ground zero, with particles falling out and potentially depositing on people caught in and under the cloud. Some of these people may not show any sign of radiation sickness and therefore not realize they have been contaminated and may take the radioactive particulate with them on their daily activities, thus spreading the radioactive particulate outside the initially contaminated area. This paper reviews the scientific literature to better understand the rate at which particulate deposits on and is removed from the different “surfaces” of a person, i.e., hair, skin, and clothing. Prior research indicates that: 1) particle deposition is usually higher on skin than on hair and clothing; 2) particle deposition is greater for a person with higher skin moisture, 3) stronger wind increases the deposition flux onto a person, and 4) the fraction of particulate deposited on the hair, skin, and clothing respectively depends on the length of the hair, assuming all the hair surface is available for deposition. The studies taken into consideration show that the largest uncertainty in particulate deposition onto a person is due to clothing type because of the different possible weave arrangements and tightness which translate into differences in actual surface area and surface roughness. A factor of 2-to-20 variation in deposition rate was found. Removal of the particulate from the contaminated person may be due to wind, a person's movement, and/or contact transfer, i.e., by touching a different clean surface. Experiments show that the majority of the particulate is resuspended within 2–6 h mostly depending on the intensity of physical activity. The largest uncertainty in particulate removal from skin depends on the skin moisture, transfer rate of single-contact, and how many objects/people a person touches per hour. No data for hair were found for particle removal and resuspension. The studies considered did not utilize radionuclides directly; however, data on adhesion of radioactive vs. their non-radioactive counterpart have shown that the uncertainty due to the radioactivity of the particles is lower than that due to other factors. In conclusion, an idealized scenario involving a single building in the path of the cloud showed the impact of building-influenced flow on the cloud transport path and mixing, which affects the radiological dose the downwind population is exposed to and consequently the health effects.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗