Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “rehabilitation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Success Using A Granular-Activated Carbon Filtration Swab to Rehabilitate Westbay{sup R} Multi-level Groundwater Monitoring Wells at the INL - 20544

In November 2015, tetrachloroethylene (PCE) was discovered in groundwater samples collected from a Westbay{sup R} multi-level groundwater monitoring well at the Idaho National Laboratory (INL).a Subsequent investigation determined that PCE was not present in the groundwater. The detected PCE was instead due to inadvertent contamination of the internal tubing fluid in the Westbay well-monitoring system, which is isolated from the surrounding groundwater. Further investigation showed that three of the 11 Westbay wells at the INL contained PCE-contaminated tubing fluid at concentrations above the U.S. Environmental Protection Agency's maximum contaminant level for drinking water (5 μg/L). Loose sediment at the bottom of some Westbay wells was also found to contain PCE; the three wells were then identified for rehabilitation as part of the INL well maintenance program. The unique construction of the Westbay wells - i.e., the small diameter (5.72 cm [2.25 in.]) and the depths of the tubing fluid ranging from 144.8 to 419 m (475 to 1,376 ft) below ground surface - posed unique challenges to the rehabilitation. Because the tubing fluid provides structural integrity, the fluid cannot be removed and then replaced without damaging the integrity of the Westbay well. Additionally, the small diameter of the systems and the associated depths limit the availability of equipment that can be used for the rehabilitation. After an evaluation of potential methods, it was determined that the use of an in-well, custom-fabricated, granular-activated-carbon filtration swab deployed via a wire line would provide the safest and most cost-effective method for rehabilitation. Westbay well rehabilitation started at well MIDDLE-2051 in late June 2018 and paused in December 2018 for the season. The PCE concentration in the tubing fluid at MIDDLE-2051 was initially reduced to a maximum concentration of 3.81 μg/L from a maximum of 642 μg/L, while the concentration of PCE in the sediment had been reduced from 5,360 to 2,270 μg/kg. Sampling was performed at MIDDLE-2051 again in August 2019, and the tubing fluid increased to a maximum concentration of 45.4 μg/L, while the concentration in the sediment decreased further to 1,890 μg/kg due to desorption of PCE from the sediment to the tubing fluid. Rehabilitation resumed at well MIDDLE-2050A in late August 2019, and the PCE concentration in the tubing fluid had been reduced to a maximum concentration of 19.0 μg/L. Although the method has been shown to be time-consuming, it has proven to be effective and safe for personnel performing the work and to the integrity of the well. Future sample data results at all wells will help determine an estimated completion of the rehabilitation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Understanding the use intention and influencing factors of telerehabilitation in people with rehabilitation needs: a cross-sectional survey

Objective This study aimed to investigate the use intention and influencing factors of telerehabilitation in people with rehabilitation needs. Methods This cross-sectional survey recruited a total of 183 participants with rehabilitation needs from May 2022 to December 2022. Sociodemographic and medical data were collected by a structured questionnaire. The factors influencing the use intention of telerehabilitation were measured by the extended Unified Theory of Acceptance and Use of Technology (UTAUT) model. Multiple hierarchical regression analyses were performed. Results A total of 150 valid questionnaires were included for analysis. The results indicated that the use intention of telerehabilitation was overall high in people with rehabilitation needs. Health condition ( β = −0.21, p = 0.03), performance expectancy ( β = 0.21, p = 0.01), facilitating conditions ( β = 0.25, p = 0.03), perceived trust ( β = 0.25, p < 0.01), and self-efficacy ( β = 0.19, p = 0.04) were significant factors influencing the use intention of telerehabilitation. Conclusion Overall, the use intention of telerehabilitation is high in individuals with rehabilitation needs. Health conditions, performance expectancy, facilitating conditions, perceived trust, and self-efficacy are important factors influencing the use intention of telerehabilitation in individuals with rehabilitation needs.

Wang, Mao-Yuan↗
DOE OSTI2025

Evaluating the Effectiveness of Soil Profile Rehabilitation for Pluvial Flood Mitigation Through Two-Dimensional Hydrodynamic Modeling

Pluvial flooding, driven by increasingly impervious surfaces and intense storm events, presents a growing challenge for urban areas worldwide. In Baltimore City, MD, USA, climate change, rapid urbanization, and aging stormwater infrastructure are exacerbating flooding impacts, resulting in significant socio-economic consequences. This study evaluated the effectiveness of a soil profile rehabilitation scenario using a 2D hydrodynamic modeling approach for the Tiffany Run watershed, Baltimore City. This study utilized different extreme storm events, a high-resolution (1 m) LiDAR Digital Terrain Model (DTM), building footprints, and hydrological soil data. These datasets were integrated into a fully coupled 2D hydrodynamic model, the City Catchment Analysis Tool (CityCAT), to simulate urban flood dynamics. The pre-soil rehabilitation simulation revealed a maximum water depth of 3.00 m in most areas, with hydrologic soil groups C and D, especially downstream of the study area. The post-soil rehabilitation simulation was targeted at vacant lots and public parcels, accounting for 33.20% of the total area of the watershed. This resulted in a reduced water depth of 2.50 m. Additionally, the baseline runoff coefficient of 0.49 decreased to 0.47 following the rehabilitation, and the model consistently recorded a peak runoff reduction rate of 4.10 across varying rainfall intensities. The validation using a contingency matrix demonstrated true-positive rates of 0.75, 0.50, 0.64, and 0 for the selected events, confirming the model’s capability at capturing real-world flood occurrences.

Baltimore City↗
DOE OSTI2024

Visual feedback and guided balance training in an immersive virtual reality environment for lower extremity rehabilitation

Balance training is essential for physical rehabilitation procedures, as it can improve functional mobility and enhance cognitive coordination. However, conventional balance training methods may have limitations in terms of motivation, real-time objective feedback, and personalization, which a virtual reality (VR) setup may provide a better alternative. In this work, we present an immersive VR training environment for lower extremity balance rehabilitation with real-time guidance and feedback. The VR training environment immerses the user in a 3D ice rink model where a virtual coach (agent) leads them through a series of balance poses, and the user controls a trainee avatar with their own movements. Here we developed two coaching styles: positive-reinforcement and autonomous-supportive, and two viewpoints of the trainee avatar: first-person and third-person. The proposed environment was evaluated in a user study with healthy, non-clinical participants (n = 16, 24.4 ± 5.7 years old, 9 females). Our results show that participants showed stronger performance in the positive-reinforcement style compared to the autonomous-supportive style. Additionally, in the third-person viewpoint, the participants exhibited more stability in the positive-reinforcement style compared to the autonomous-supportive style. For viewpoint, participants exhibited stronger performance in the first-person viewpoint compared to third-person in the autonomous-supportive style, while they were comparable in the positive-reinforcement style. We observed no significant effects on the foot height and number of mistakes. Furthermore, we report the analysis of user performance with balance training poses and subjective measures based on questionnaires to assess the user experience, usability, and task load. The proposed VR balance training could offer an interactive, adaptive, and engaging environment and open new potential research directions for lower extremity rehabilitation.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Maximizing Strength: The Stimuli and Mediators of Strength Gains and Their Application to Training and Rehabilitation

Abstract Spiering, BA, Clark, BC, Schoenfeld, BJ, Foulis, SA, and Pasiakos, SM. Maximizing strength: the stimuli and mediators of strength gains and their application to training and rehabilitation. J Strength Cond Res 37(4): 919–929, 2023—Traditional heavy resistance exercise (RE) training increases maximal strength, a valuable adaptation in many situations. That stated, some populations seek new opportunities for pushing the upper limits of strength gains (e.g., athletes and military personnel). Alternatively, other populations strive to increase or maintain strength but cannot perform heavy RE (e.g., during at-home exercise, during deployment, or after injury or illness). Therefore, the purpose of this narrative review is to (a) identify the known stimuli that trigger gains in strength; (b) identify the known factors that mediate the long-term effectiveness of these stimuli; (c) discuss (and in some cases, speculate on) potential opportunities for maximizing strength gains beyond current limits; and (d) discuss practical applications for increasing or maintaining strength when traditional heavy RE cannot be performed. First, by conceptually deconstructing traditional heavy RE, we identify that strength gains are stimulated through a sequence of events, namely: giving maximal mental effort, leading to maximal neural activation of muscle to produce forceful contractions, involving lifting and lowering movements, training through a full range of motion, and (potentially) inducing muscular metabolic stress. Second, we identify factors that mediate the long-term effectiveness of these RE stimuli, namely: optimizing the dose of RE within a session, beginning each set of RE in a minimally fatigued state, optimizing recovery between training sessions, and (potentially) periodizing the training stimulus over time. Equipped with these insights, we identify potential opportunities for further maximizing strength gains. Finally, we identify opportunities for increasing or maintaining strength when traditional heavy RE cannot be performed.

Sport Sciences↗
DOE OSTI2026

Large Power Transformer Supply Chain Gap Analysis and Domestic Content Strategies for Hydropower Rehabilitation: Supplemental Report

Large Power Transformers (LPTs) are indispensable to U.S. hydropower operations, serving as generator step-up (GSU) units that interconnect hydro facilities to the transmission grid. Yet the LPT supply chain faces mounting stress from aging infrastructure, limited domestic production, and long lead times. Currently, more than 80% of LPT demand is met through imports, with primary suppliers including Mexico, South Korea, Brazil, Austria, and Canada. Domestic manufacturers supply only about 20% of units, constrained by bottlenecks in high-grade Grain-Oriented Electrical Steel (GOES), copper conductors, bushings, and on-load tap changers (OLTCs). Hydropower rehabilitation projects in particular face additional challenges due to custom design requirements, remote siting, and regulatory needs around domestic content. Regional cost disparities, driven by transportation logistics, labor markets, and import price volatility, further exacerbate project risks. To address these vulnerabilities, coordinated action is required: strengthening domestic capacity for GOES and secondary components, developing near-site assembly hubs, and leveraging IRS domestic content safe harbors to incentivize U.S. manufacturing. This addendum refines the 2024 NREL Hydropower Supply Chain Gap Analysis by focusing specifically on critical issues related to LPT domestic manufacturing capacity and key considerations for hydropower developers and asset owners.

13 HYDRO ENERGY↗
DOE OSTI2024

Angle Assessment for Upper Limb Rehabilitation: A Novel Light Detection and Ranging (LiDAR)-Based Approach

The accurate measurement of joint angles during patient rehabilitation is crucial for informed decision making by physiotherapists. Presently, visual inspection stands as one of the prevalent methods for angle assessment. Although it could appear the most straightforward way to assess the angles, it presents a problem related to the high susceptibility to error in the angle estimation. In light of this, this study investigates the possibility of using a new approach to angle calculation: a hybrid approach leveraging both a camera and LiDAR technology, merging image data with point cloud information. This method employs AI-driven techniques to identify the individual and their joints, utilizing the cloud-point data for angle computation. The tests, considering different exercises with different perspectives and distances, showed a slight improvement compared to using YOLO v7 for angle calculation. However, the improvement comes with higher system costs when compared with other image-based approaches due to the necessity of equipment such as LiDAR and a loss of fluidity during the exercise performance. Therefore, the cost–benefit of the proposed approach could be questionable. Nonetheless, the results hint at a promising field for further exploration and the potential viability of using the proposed methodology.

Klein, Luan C. (ORCID:000000016306574X)↗
DOE OSTI2020

Diazotrophs Show Signs of Restoration in Amazon Rain Forest Soils with Ecosystem Rehabilitation

Biological nitrogen fixation can be an important source of nitrogen in tropical forests that serve as a major CO 2 sink. Extensive deforestation of the Amazon is known to influence microbial communities and the biogeochemical cycles they mediate. However, it is unknown how diazotrophs (nitrogen-fixing microorganisms) respond to deforestation and subsequent ecosystem conversion to agriculture, as well as whether they can recover in secondary forests that are established after agriculture is abandoned. To address these knowledge gaps, here we combined a spatially explicit sampling approach with high-throughput sequencing of nifH genes. The main objectives were to assess the functional distance decay relationship of the diazotrophic bacterial community in a tropical forest ecosystem and to quantify the roles of various factors that drive the observed changes in the diazotrophic community structure. We observed an increase in local diazotrophic diversity (α-diversity) with a decrease in community turnover (β-diversity), associated with a shift in diazotrophic community structure as a result of the forest-to-pasture conversion. Both diazotrophic community turnover and structure showed signs of recovery in secondary forests. Changes in the diazotrophic community were primarily driven by the change in land use rather than differences in geochemical characteristics or geographic distances. The diazotroph communities in secondary forests resembled those in primary forests, suggesting that at least partial recovery of diazotrophs is possible following agricultural abandonment. IMPORTANCE The Amazon region is a major tropical forest region that is being deforested at an alarming rate to create space for cattle ranching and agriculture. Diazotrophs (nitrogen-fixing microorganisms) play an important role in supplying soil N for plant growth in tropical forests. It is unknown how diazotrophs respond to deforestation and whether they can recover in secondary forests that establish after agriculture is abandoned. Using high-throughput sequencing of nifH genes, we characterized the response of diazotrophs’ β-diversity and identified major drivers of changes in diazotrophs from forest-to-pasture and pasture-to-secondary-forest conversions. Studying the impact of land use change on diazotrophs is important for a better understanding of the impact of deforestation on tropical forest ecosystem functioning, and our results on the potential recovery of diazotrophs in secondary forests imply the possible restoration of ecosystem functions in secondary forests.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

(U) Blast Tube Rehabilitation (Final Design Review) [Slides]

Saddle design is being proposed to improve overall response of facility. No plasticity predicted in tube sections buying down risk of a catastrophic failure. Plasticity is predicted in the support for loadings representing 190# C4. The design has been iterated to decrease localized plasticity and buy down risk. It is recommended that no amount of explosive driver be placed in A36 sections. Previous work suggests yielding can develop in the tube section causing rupture. J2 colleagues have reviewed analysis results. Outstanding question of additional plastic strain is developing from subsequent uses.

42 ENGINEERING↗
DOE OSTI2022

Mitigating life cycle GHG emissions of roads to be built through 2030: Case study of a Chinese province

We report the expansion of road networks in emerging economies such as China causes significant greenhouse gas (GHG) emissions. This development is conflicting with China's commitment to achieve carbon neutrality. Thus, there is a need to better understand life cycle emissions of road infrastructure and opportunities to mitigate these emissions. Existing impact studies of roads in developing countries do not address recycled materials, improved pavement maintenance, or pavement-vehicle interaction and electric vehicle (EV) adoption. Combining firsthand information from Chinese road construction engineers with publicly available data, this paper estimates a comprehensive account of GHG emissions of the road pavement network to be constructed in the next ten years in the Shandong province in Northern China. Further, we estimate the potential of GHG emission reductions achievable under three scenario sets: maintenance optimization, alternative pavement material replacement, and EV adoption. Results show that the life cycle GHG emissions of highways and Class 1–4 roads to be constructed in the next 10 years amount to 147 Mt CO2-eq. Considering the use phase in our model reveals that it is the dominant stage in terms of emissions, largely due to pavement-vehicle interaction. Vehicle electrification can only moderately mitigate these emissions. Other stages, such as materials production and road maintenance and rehabilitation, contribute substantially to GHG emissions as well, highlighting the importance of optimizing the management of these stages. Surprisingly, longer, not shorter maintenance intervals, yield significant emission reductions. Another counter-intuitive finding is that thicker and more material-intensive pavement surfaces cause lower emissions overall. Taken together, optimal maintenance and rehabilitation schedules, alternative material use, and vehicle electrification provide GHG reduction potentials of 11%, 4%–16% and 2%–6%, respectively.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Resource selection and species interactions between native and non‐native fishes in a simulated stream system

Abstract Effective fishery management necessitates understanding of resource partitioning by fishes that inhabit complex systems composed of biotic and abiotic features. Evaluations of non‐native species introductions have continually demonstrated adverse effects associated with abundance and distribution of native fishes. Therefore, understanding resource selection and interactions between native and non‐native species is important for recovery efforts. Habitat use by two native fish species (largescale sucker Catostomus macrocheilus [Girard] and mountain whitefish Prosopium williamsoni [Girard]) and one non‐native fish species (pumpkinseed Lepomis gibbosus [Linnaeus]) of the Kootenai River, Idaho, were evaluated in a laboratory stream system. Trials were conducted in allopatry and in sympatry with and without the presence of wood to describe habitat selection in the context of on‐going habitat rehabilitation efforts. Interactions were evident between native largescale sucker and non‐native pumpkinseed concerning use of a woody structure and current velocity. Mountain whitefish used low‐velocity habitats and selected locations that were further from wood when in sympatry with pumpkinseed. Our research suggests that habitat use of native, large‐river fishes may be influenced by the presence of a non‐native species, and that considering such interactions is critical when designing and implementing habitat rehabilitation efforts in river ecosystems.

Branigan, Philip R.↗
DOE OSTI2022

Cold Spray Additive Manufacturing For New Pipeline Fabrication In Live, Natural Gas Distribution Mains

ULC Technologies (ULC) and the Penn State University Applied Research Lab (PSU ARL) developed a process and approach for rehabilitating live, natural gas distribution pipelines using Cold Spray Additive Manufacturing (CSAM). Robotic inline fabrication of a new pipe will be performed inside a natural gas main without disrupting customers. The material studied was blended with stainless steel which offers corrosion resistance, high strength and compatibility with hydrogen to enable a robust pipeline system that is future proofed. Stainless steel coatings sprayed and tested in the lab showed excellent strength, ductility, and porosity values. ULC initially sought to use methane as the process gas for compatibility with the host pipe, but after evaluating the field and lab challenges, nitrogen was deemed to be more suitable. Early robotic concepts have been developed that indicate technical feasibility. While the technology development originally targeted natural gas distribution mains, market research showed a broader need. Spot repairs performed in natural gas transmission mains may be a more economical approach for reinforcing distribution and transmission mains compared with full pipe-in-pipe rehabilitation. Additive manufacturing offers custom programming, as well as high accuracy and precision. This means custom contours can be manufactured in situ, offering flexibility in the repair solution, such as fabricating internal full circumferential sleeves. The value of the repair can be high at difficult-to-reach locations and in pipes that need reinforcement before the injection of methane-hydrogen blends.

03 NATURAL GAS↗