Results for “prompt optimization”

NASA NTRS1996

Compression Molding of Composite of Recycled HDPE and Recycled Tire Particles

Plastic and rubber recycling is an effective means of reducing solid waste to the environment and preserving natural resources. A project aimed at developing a new composite material from recycled high density polyethylene (HDPE) and recycled rubber is currently being conducted at Eastern Illinois University. The recycled plastic pellets with recycled rubber particles are extruded into some HDPE/rubber composite strands. The strand can be further cut into pellets that can be used to fabricate other material forms or products. This experiment was inspired by the above-mentioned research activity. In order to measure Durometer hardness of the extruded composite, a specimen with relatively large dimensions was needed. Thus, compression molding was used to form a cylindrical specimen of 1 in. diameter and 1 in. thickness. The initial poor quality of the molded specimen prompted a need to optimize the processing parameters such as temperature, holding time, and pressure. Design of experiment (DOE) was used to obtain optimum combination of the parameters.

Liu, Ping↗

NASA NTRSDate not supplied

Comparison and Application of Battery Modeling Methods for Conceptual Electric Aircraft

Growing interest in design and optimization of electrified aircraft propulsion concepts prompts the need for accurate, flexible, and efficient methods to model battery systems. Presented in this paper are three battery modeling methods that have been used at NASA’s Glenn Research Center, each representing different mathematical or electrical approaches. Thévenin equivalent circuit, normalization, and curve-fitting methods are compared against battery cell test data for the X-57 Maxwell electric aircraft technology demonstrator. The methods are then applied in a simple multidisciplinary optimization context using NASA’s Six-Passenger Electric Quadrotor concept to determine their applicability and performance. The normalization method achieves the highest accuracy for steady and unsteady discharge rates with a voltage mean error percentage of 0.423% and 1.186%, respectively. Optimal quadrotor mission range between the models varies up to 0.5 nmi, identifying current battery modeling methods as a potentially significant contributor to mission analysis error. A set of relevant tools and techniques for conceptual battery modeling are identified in this paper, with conclusions made on the utility of each modeling approach for various design challenges.

power↗

NASA NTRS1978

Terminal-area flight experience with the NASA Terminal Configured Vehicle

Increases in the volume of air traffic around major terminals, as well as the advent of MLS and other sophisticated ATC techniques, have prompted the development of aircraft specifically optimized for flight in terminal areas. A modified Boeing 737, developed by NASA, is presented as an illustration of a Terminal Configured Vehicle (TCV). Among the TCV systems discussed are the electronic attitude direction indicator (EADI) and the electronic horizontal situation indicator (EHSI), both of which are advanced display systems capable of positioning the runway center line from a variety of glide slope paths, and with reference to time, i.e., the on-board computer can predict where the aircraft will be at a given number of seconds from the time of the analysis. Thus, 4-D navigation (time path) can be selected as a control mode, together with vertical and horizontal path modes.

Morello, S. A.↗

NASA NTRS1998

Joint ASRS and NASA Callback on FANS-1 Datalink Operational Incidents

The recent certification and implementation of the Future Air Navigation System (FANS- 1) was based on the benefits of reduced separation minima, ability to optimize flight plans enroute, and the prompt transmission and reception of messages between oceanic controllers and 747-400 aircraft transiting the Pacific. In addition, FANS was intended to supersede High Frequency (HF) radio which has been the staple, yet problematic, long distance communication link for years. However, in the three initial years of operation, FANS has revealed its own unique operational issues. Although some technical and engineering problems have been studied and addressed, little research has been conducted on human factors issues associated with the use of FANS on the flight deck. This lack of prior data on the operational use of FANS prompted a joint NASA/Aviation Safety Reporting System (ASRS) inquiry into FANS datalink. In addition, two foreign air carriers and their respective safety agencies were recruited to participate. This international FANS research effort consisting of three aviation safety agencies and three international commercial air-carriers has provided a unique opportunity for conducting human factors research in an operational environment. An ASRS 'callback' format was chosen for the study as a practical and viable method for capturing FANS events on the flight deck. Initially, 747-400 pilots were encouraged to submit reports to their respective safety agencies if they had experienced any positive or negative incidents with the use of FANS. Upon receipt of a report, it was evaluated and if deemed pertinent to the study, a telephone interview or 'callback' was conducted on the FANS incident to elicit further details, capture the key events, and gather contextual information. Once the operational data collection phase was completed, the reports and interviews were analyzed with two purposes in mind: primarily to identify and address problematic human factors issues with current FANS technology, and, secondarily, to provide 'lessons learned' for future datalink systems and implementation.

Moses, John↗

NASA NTRS1993

Advanced cargo aircraft may offer a potential renaissance in freight transportation

The increasing demand for air freight transportation has prompted studies of large, aerodynamically efficient cargo-optimized aircraft capable of carrying intermodal containers, which are typically 8 x 8 x 20 ft. Studies have accordingly been conducted within NASA to ascertain the specifications and projected operating costs of such a vehicle, as well as to identify critical, development-pacing technologies. Attention is here given not only to the rather conventional, 10-turbofan engined configuration thus arrived at, but numerous innovative configurations featuring such concepts as spanloading, removable cargo pods, and ground effect.

Morris, Shelby J.↗

NASA NTRS2005

Martian Radiative Transfer Modeling Using the Optimal Spectral Sampling Method

The large volume of existing and planned infrared observations of Mars have prompted the development of a new martian radiative transfer model that could be used in the retrievals of atmospheric and surface properties. The model is based on the Optimal Spectral Sampling (OSS) method [1]. The method is a fast and accurate monochromatic technique applicable to a wide range of remote sensing platforms (from microwave to UV) and was originally developed for the real-time processing of infrared and microwave data acquired by instruments aboard the satellites forming part of the next-generation global weather satellite system NPOESS (National Polarorbiting Operational Satellite System) [2]. As part of our on-going research related to the radiative properties of the martian polar caps, we have begun the development of a martian OSS model with the goal of using it to perform self-consistent atmospheric corrections necessary to retrieve caps emissivity from the Thermal Emission Spectrometer (TES) spectra. While the caps will provide the initial focus area for applying the new model, it is hoped that the model will be of interest to the wider Mars remote sensing community.

Eluszkiewicz, J.↗

NASA NTRS2009

Data Analysis for the LISA Pathfinder Mission

The LTP (LISA Technology Package) is the core part of the Laser Interferometer Space Antenna (LISA) Pathfinder mission. The main goal of the mission is to study the sources of any disturbances that perturb the motion of the freely-falling test masses from their geodesic trajectories as well as 10 test various technologies needed for LISA. The LTP experiment is designed as a sequence of experimental runs in which the performance of the instrument is studied and characterized under different operating conditions. In order to best optimize subsequent experimental runs, each run must be promptly analysed to ensure that the following ones make best use of the available knowledge of the instrument ' In order to do this, all analyses must be designed and tested in advance of the mission and have sufficient built-in flexibility to account for unexpected results or behaviour. To support this activity, a robust and flexible data analysis software package is also required. This poster presents two of the main components that make up the data analysis effort: the data analysis software and the mock-data challenges used to validate analysis procedures and experiment designs.

Thorpe, James Ira↗

NASA NTRS1995

Alternate charging profiles for the onboard nickel cadmium batteries of the Explorer Platform/Extreme Ultraviolet Explorer

The Explorer Platform/Extreme Ultraviolet Explorer (EP/EUVE) spacecraft power is provided by the Modular Power Subsystems (MPS) which contains three 50 ampere-hour Nickel Cadmium (NiCd) batteries. The batteries were fabricated by McDonnell Douglas Electronics Systems Company, with the cells fabricated by Gates Aerospace Batteries (GAB), Gainesville, Florida. Shortly following launch, the battery performance characteristics showed similar signatures as the anomalous performance observed on both the Upper Atmosphere Research Satellite (UARS) and the Compton Gamma Ray Observatory (CGRO). This prompted the development and implementation of alternate charging profiles to optimize the spacecraft battery performance. The Flight Operations Team (FOT), under the direction of Goddard Space Flight Center's (GSFC) EP/EUVE Project and Space Power Applications Branch have monitored and managed battery performance through control of the battery Charge to Discharge (C/D) ratio and implementation of a Solar Array (SA) offset. This paper provides a brief overview of the EP/EUVE mission, the MPS, the FOT's battery management for achieving the alternate charging profile, and the observed spacecraft battery performance.

Rao, Gopalakrishna M.↗

NASA NTRS2010

AXTAR: Mission Design Concept

The Advanced X-ray Timing Array (AXTAR) is a mission concept for X-ray timing of compact objects that combines very large collecting area, broadband spectral coverage, high time resolution, highly flexible scheduling, and an ability to respond promptly to time-critical targets of opportunity. It is optimized for sub-millisecond timing of bright Galactic X-ray sources in order to study phenomena at the natural time scales of neutron star surfaces and black hole event horizons, thus probing the physics of ultra-dense matter, strongly curved spacetimes, and intense magnetic fields. AXTAR s main instrument, the Large Area Timing Array (LATA) is a collimated instrument with 2 50 keV coverage and over 3 square meters effective area. The LATA is made up of an array of super-modules that house 2-mm thick silicon pixel detectors. AXTAR will provide a significant improvement in effective area (a factor of 7 at 4 keV and a factor of 36 at 30 keV) over the RXTE PCA. AXTAR will also carry a sensitive Sky Monitor (SM) that acts as a trigger for pointed observations of X-ray transients in addition to providing high duty cycle monitoring of the X-ray sky. We review the science goals and technical concept for AXTAR and present results from a preliminary mission design study

Ray, Paul S.↗

NASA NTRSDate not supplied

Combinatorial Reasoning: Selecting Reasons in Generative AI Pipelines via Combinatorial Optimization

Recent Large Language Models (LLMs) have demonstrated impressive capabilities at tasks that require human intelligence and are a significant step towards human-like artificial intelligence (AI). Yet the performance of LLMs at reasoning tasks have been subpar and the reasoning capability of LLMs is a matter of significant debate. While it has been shown that the choice of the prompting technique to the LLM can alter its performance on a multitude of tasks, including reasoning, the best performing techniques require human-made prompts with the knowledge of the tasks at hand. We introduce a framework for what we call Combinatorial Reasoning (CR), a fully-automated prompting method, where reasons are sampled from an LLM pipeline and mapped into a Quadratic Unconstrained Binary Optimization (QUBO) problem. The framework investigates whether QUBO solutions can be profitably used to select a useful subset of the reasons to construct a Chain-of-Thought style prompt. We explore the acceleration of CR with specialized solvers. We also investigate the performance of simpler zero-shot strategies such as linear majority rule or random selection of reasons. Our preliminary study indicates that coupling a combinatorial solver to generative AI pipelines is an interesting avenue for AI reasoning and elucidates design principles for future CR methods.

combinatorial reasoning↗

NASA NTRSDate not supplied

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

NASA NTRSDate not supplied

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

NASA NTRSDate not supplied

Transient Optimization of a Gas Turbine Engine

Gas turbine engines are the primary power plants for modern commercial aircraft. Transients prompted by significant changes in thrust or power demand are common and unavoidable. Extreme transient scenarios such as those associated with a go-around during a landing attempt are possible and must be accounted for in the design of the engine and its controller. Engine transients tend to cause a reduction in compressor operability margin, which must be addressed by the engine control system and accounted for in the engine design to prevent events such as compressor stall/surge and combustor blow out. Transient operability concerns typically lead to compromises in the engine design that sacrifice efficiency and/or limit responsiveness. Transient operability is typically managed by logic that limits the fuel flow command. If this logic is not optimized, then the potential for valuable performance could be lost. This study presents a strategy for optimizing the transient limit logic and proposes a strategy for updating the control logic over the lifespan of the engine. The results demonstrate significant improvements in transient operability. For example, of the results at sea level static conditions demonstrated a 31% reduction in the usage of the high pressure compressor operability stack during a snap acceleration transient. Furthermore, a reinforcement learning algorithm is demonstrated to modify the transient logic as the engine degrades to minimize response time while respecting a prescribed compressor operability margin limit. A simple demonstration of the reinforcement learning algorithm resulted in a thrust response time reduction of ~11.8%.

transient↗

NASA NTRS2014

Optimization Strategies for Single-Stage, Multi-Stage and Continuous ADRs

Adiabatic Demagnetization Refrigerators (ADR) have many advantages that are prompting a resurgence in their use in spaceflight and laboratory applications. They are solid-state coolers capable of very high efficiency and very wide operating range. However, their low energy storage density translates to larger mass for a given cooling capacity than is possible with other refrigeration techniques. The interplay between refrigerant mass and other parameters such as magnetic field and heat transfer points in multi-stage ADRs gives rise to a wide parameter space for optimization. This paper first presents optimization strategies for single ADR stages, focusing primarily on obtaining the largest cooling capacity per stage mass, then discusses the optimization of multi-stage and continuous ADRs in the context of the coordinated heat transfer that must occur between stages. The goal for the latter is usually to obtain the largest cooling power per mass or volume, but there can also be many secondary objectives, such as limiting instantaneous heat rejection rates and producing intermediate temperatures for cooling of other instrument components.

sub-kelvin cooling↗

NASA NTRS2023

Optimizing the Resolution of Hydrodynamic Simulations for MCRaT Radiative Transfer Calculations

Despite their discovery about half a century ago, the Gamma-ray burst (GRB) prompt emission mechanism is still not well understood. Theoretical modeling of the prompt emission has advanced considerably due to new computational tools and techniques. One such tool is the PLUTO hydro dynamics code, which is used to numerically simulate GRB outflows. PLUTO uses Adaptive Mesh Refinement to focus computational efforts on the portion of the grid that contains the simulated jet. Another tool is the Monte Carlo Radiation Transfer (MCRaT) code, which predicts electromagnetic signatures of GRBs by conducting photon scatterings within a jet using PLUTO. The effects of the underlying resolution of a PLUTO simulation with respect to MCRaT post-processing radiative transfer results have not yet been quantified. We analyze an analytic spherical outflow and a hydrodynamically simulated GRB jet with MCRaT at varying spatial and temporal resolutions and quantify how decreasing both resolutions affect the resulting mock observations. We find that changing the spatial resolution changes the hydrodynamic properties of the jet, which directly affect the MCRaT mock observable peak energies. We also find that decreasing the temporal resolution artificially decreases the high energy slope of the mock observed spectrum, which increases both the spectral peak energy and the luminosity. We show that the effects are additive when both spatial and temporal resolutions are modified. Our results allow us to understand how decreased hydrodynamic temporal and spatial resolutions affect the results of post-processing radiative transfer calculations, allowing for the optimization of hydrodynamic simulations for radiative transfer codes.

Jose Arita-Escalante↗

NASA NTRSDate not supplied

NTAC Augmented Nuclear and Advanced Propulsion

Currently, there are two types of nuclear propulsion: Nuclear Thermal Propulsion (NTP) and Nuclear Electric Propulsion (NEP). Common to both types, a nuclear reactor generates heat energy to raise the temperature of propellant, or the generated heat energy is converted into electric power. The electricity generated powers propulsion systems, such as a Hall thruster, magnetoplasma dynamic (MPD) thruster, or variable specific impulse magnetoplasma rocket (VASIMR). Customarily, only the thermal energy output from nuclear reaction is considered for NTP and NEP systems. However, the nuclear fission reaction can also generate ~7 MeV of prompt gamma rays. Therefore, most designers of NTP and NEP systems incorporate safety features to shield against this radiation. An optimized design approach would be to integrate a Nuclear Thermionic Avalanche Cell (NTAC) within the NTP or NEP structure for converting this radiation energy into additional electric power, while also shielding gamma rays. Consequently, this study addresses several combinations of NTP and NEP structures with NTAC devices in order to achieve that goal.

NTAC↗

NASA NTRS2008

A Computational Approach for Model Update of an LS-DYNA Energy Absorbing Cell

NASA and its contractors are working on structural concepts for absorbing impact energy of aerospace vehicles. Recently, concepts in the form of multi-cell honeycomb-like structures designed to crush under load have been investigated for both space and aeronautics applications. Efforts to understand these concepts are progressing from tests of individual cells to tests of systems with hundreds of cells. Because of fabrication irregularities, geometry irregularities, and material properties uncertainties, the problem of reconciling analytical models, in particular LS-DYNA models, with experimental data is a challenge. A first look at the correlation results between single cell load/deflection data with LS-DYNA predictions showed problems which prompted additional work in this area. This paper describes a computational approach that uses analysis of variance, deterministic sampling techniques, response surface modeling, and genetic optimization to reconcile test with analysis results. Analysis of variance provides a screening technique for selection of critical parameters used when reconciling test with analysis. In this study, complete ignorance of the parameter distribution is assumed and, therefore, the value of any parameter within the range that is computed using the optimization procedure is considered to be equally likely. Mean values from tests are matched against LS-DYNA solutions by minimizing the square error using a genetic optimization. The paper presents the computational methodology along with results obtained using this approach.

Horta, Lucas G.↗

NASA NTRS1993

Clinical physiology of bed rest

Maintenance of optimal health in humans requires the proper balance between exercise, rest, and sleep as well as time in the upright position. About one-third of a lifetime is spent sleeping; and it is no coincidence that sleeping is performed in the horizontal position, the position in which gravitational influence on the body is minimal. Although enforced bed rest is necessary for the treatment of some ailments, in some cases it has probably been used unwisely. In addition to the lower hydrostatic pressure with the normally dependent regions of the cardiovascular system, body fuid compartments during bed rest in the horizontal body position, and virtual elimination of compression on the long bones of the skeletal system during bed rest (hypogravia), there is often reduction in energy metabolism due to the relative confinement (hypodynamia) and alteration of ambulatory circadian variations in metabolism, body temperature, and many hormonal systems. If patients are also moved to unfamiliar surroundings, they probably experience some feelings of anxiety and some sociopsychological problems. Adaptive physiological responses during bed rest are normal for that environment. They are attempts by the body to reduce unnecessary energy expenditure, to optimize its function, and to enhance its survival potential. Many of the deconditioning responses begin within the first day or two of bed rest; these early responses have prompted physicians to insist upon early resumption of the upright posture and ambulation of bedridden patients.

Greenleaf, John E.↗