Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power take-off”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1944

Use of Internal Coolant as a Means of Permitting Increase in Engine Take-Off Power

Engine tests, together with estimates made at Langley Memorial Aeronautical Laboratory, indicate that a 25-percent increase in take-off power can be obtained with present-day aircraft engines without increasing either the knock limit of the fuel or the external cooling requirements of the engine. This increase in power with present fuels and present external cooling is made possible through the use of an internal coolant inducted through the inlet manifold. Estimates on aircraft indicate that this 25-percent increase in power will permit an approximate usable increase of 8.5 percent in the take-off load of existing military airplanes. This increase in load is equivalent to an increase in the weight of gasoline normally carried of between 30 and 65 percent.

FUELS, ANTIKNOCK↗
NASA NTRS1939

The Way to Increased Airplane Engine Power

The purpose of this paper is to give an outline of the present state of development and point out the possibilities available for the further increase in the power/displacement ratio, the economy, and the reliability of the engine. Some of the aspects discussed are methods of increasing take-off power, the various methods of preparation of the fuel mixture and their effect on power, economy, and safety.

Vohrer, Eugen↗
NASA NTRS1948

Natural icing of an axial-flow turbojet engine in flight for a single icing condition

An investigation has been conducted in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. One flight was made in an icing condition in which the liquid-water content varied from 0.077 to 0.490 gram per cubic meter and the average droplet size varied from 5.4 to 12.1 microns. During a period of 60 minutes in icing, at an engine speed of 11,000 rpm, the tail-pipe temperature increased from 865 degrees to 965 degrees F. and the jet thrust decreased from 1950 to 1700 pounds. Near the end of the icing period, the engine was satisfactorily accelerated to take-off power.

Acker, Loren W↗
NASA NTRS1943

Wind-Tunnel Tests of the 1/9-Scale Model of the Curtiss XP-62 Airplane with Various Vertical Tail Arrangements

The effect of various vertical tail arrangements upon the stability and control characteristics of an XP-62 fighter model was investigated. Rudder-free yaw characteristics with take-off power and flaps deflected were satisfactory after dorsal fin modifications. Directional stability was obtained with all modified vertical tails. Satisfactory rudder effectiveness resulted partly because the dual-rotation propellers produced no asymmetric yawing moments. Pedal forces in sideslips were undesirably large but may be easily reduced.

Wallace, Arthur R.↗
NASA NTRS1932

Towing tests of models as an aid in the design of seaplanes

This report concerns the making and evaluation of a towing test of a seaplane float system. Some of the topics considered are: 1) the influence of the wing cell and power plant on the take-off performance; 2) the determination of the resistance curve for the take-off free to trim; 3) the resistance curves with elevator control (at fixed trims); 4) take-off time and take-off run.

Schroder, P↗
NASA NTRS1928

On the take-off of heavily loaded airplanes

This report examines the take-off conditions of airplanes equipped with tractive propellers, and particularly the more difficult take-off of airplanes heavily loaded per unit of wing area (wing loading) or per unit of engine power (power loading).

LOADS, TAKE-OFF↗
NASA NTRS1938

Tank Tests to Show the Effect Rivet Heads on the Water Performance of a Seaplane-Float

A 1/3.5 full-sized model of a seaplane float constructed from lines supplied by the Bureau of Aeronautics, Navy Department, was tested first with smooth painted bottom surfaces and then with round-head rivets, plate laps, and keel plates fitted to simulate the actual bottom of a metal float. A percentage increase in water resistance caused by the added roughness was found to be from 5 to 20 percent at the hump speed and from 15 to 40 percent at high speeds. The effect of the roughness of the afterbody was found to be negligible except at high trims. The model data were extrapolated to full size by the usual method that assumes the forces to vary according to Froude's law and, in the case of the smooth model, by a method of separation that takes into account the effect of scale on the frictional resistance. It was concluded that the effect of rivet heads on the take-off performance of a relatively high-powered float seaplane is of little consequence, but it may be of greater importance in the case of more moderately powered flying boats.

FLOATS - RESISTANCE EFFECT OF SURFACE ROUGHNESS↗
NASA NTRS1934

The calculated effect of trailing-edge flaps on the take-off of flying boats

The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust. It is indicated that flaps would allow a decrease in the high angles of wing setting necessary with most seaplanes, provided that the excess thrust is not too low.

Parkinson, J E↗
NASA NTRS1936

Calculated effect of various types of flap on take-off over obstacles

In order to determine whether or not flaps could be expected to have any beneficial effect on take-off performance, the distances required to take off and climb to an altitude of 50 feet were calculated for hypothetical airplanes, corresponding to relatively high-speed types and equipped with several types of flap. The types considered are the Fowler wing, the Hall wing, the split flap, the balanced split flap, the plain flap, and the external-airfoil flap. The results indicate that substantial reductions in take-off distance are possible through the use of flaps, provided that the proper flap angle corresponding to a given set of conditions is used. The best flap angle for taking off varies inversely as power loading and, to a much smaller extent, varies inversely with wing loading. Apparently, the best take-off characteristics are provided by the type of device in which the flap forms an extension to the main wing as in the case of the Fowler wing and the external-airfoil flap.

Wetmore, J W↗
NASA NTRS1941

Wind-tunnel Tests of Eight-blade Single and Dual-rotating Propellers in the Tractor Position

Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade propellers, but presence of a wing reduced gain about one-half. Greater power absorption caused by dual rotation over flight range and higher efficiency or thrust for range of take-off and climb was indicated

PROPELLER-WING COMBINATIONS↗
NASA NTRS1927

A warning concerning the take-off with heavy load

A successful take-off can be made with an airplane so heavily loaded that it cannot climb to a height greater than the span of its wings. The explanation is that the power required to maintain level flight at an altitude of the order of the wing span may be as much as 50 per cent greater than that necessary when the airplane is just clear of the ground. The failure of heavily loaded airplanes to continue climbing at the rate attained immediately after the actual take-off is a grave hazard and has resulted in great risk or catastrophe in three notable cases which are cited.

Reid, Elliott G↗
NASA NTRS1938

The Effect of Compressibility on Eight Full-Scale Propellers Operating in the Take-Off and Climbing Range

Tests were made of eight full-scale propellers of different shape at various tip speeds up to about 1,000 feet per second. The range of blade-angle settings investigated was from 10 degrees to 30 degrees at the 0.75 radius. The results indicate that a loss in propulsive efficiency occurred at tip speeds from 0.5 to 0.7 the velocity of sound for the take-off and climbing conditions. As the tip speed increased beyond these critical values, the loss rapidly increased and amounted, in some instances, to more than 20 percent of the thrust power for tip-speed values of 0.8 the speed of sound. In general, as the blade-angle setting was increased, the loss started to occur at lower tip speeds. The maximum loss for a given tip speed occurred at a blade-angle setting of about 20 degrees for the take-off and 25 degrees for the climbing condition. A simplified method for correcting propellers for the effect of compressibility is given in an appendix.

Biermann, David↗
NASA NTRS1934

Complete tank tests of two flying-boat hulls with pointed steps - N.A.C.A. Models 22-A and 35

This note presents the results of complete tank test of N.A.C.A. Models 22-A and 35, two flying-boat hulls of the deep pointed-step type with low dead rise. Model 22-A is a form derived by modification of Model 22, the test results of which are given in N.A.C.A. Technical Note No. 488. Model 35 is a form of the same type but has a higher length-beam ratio than either Model 22 or 22-A. Take-off examples are worked out using data from these tests and a previous test of a conventional model applied to an arbitrary set of design specifications for a 15,000-pound flying boat. The comparison of these examples shows both pointed-step models to be superior to the conventional form, and Model 35 to be the better of the two. Model 35 is applied to a hypothetical 100,000-pound flying boat of the twin-hull type and performance calculations are made both for take-off and range. The results indicate that the high performance of this type of hull will enable the designer to use higher wing and power loadings than are found in current practice, with a resulting increase in range and pay load.

Shoemaker, James M↗
NASA NTRS1934

A method of calculating the performance of controllable propellers with sample computations

This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency. Controllable propellers are of particular advantage when used with geared and with supercharged engines. A controllable propeller reduces the take-off run, increases the rate of climb and the ceiling, but does not increase the high speed, except when operating above the design altitude of the previously used fixed-pitch propeller or when that propeller was designed for other than high speed.

Hartman, Edwin P↗
NASA NTRSDate not supplied

Aerothermal Shape Optimization of Actively-Cooled Battery Packs using Conjugate Heat Transfer

Thermal management for battery is important for electric aircraft because battery temperature is critically important to vehicle safety, and it also has direct impact on the efficiency of the battery system. Because ambient air is a readily available resource for aircraft, this paper considers an active cooling concept with forced convection of ambient air through the battery pack. Conjugate heat transfer analysis is used to solve the coupled aero-thermal problem, which consists of a finite-volume computational fluid dynamics solver for the fluid domain, and a conduction heat transfer solver for the solid domain. A mixed Neumann and Dirichlet boundary condition is developed for the fluid-solid interface, which allows the solid domain to completely submerge in the fluid domain. A gradient-based optimization method is adopted, and the discrete adjoint approach implemented in DAFoam is used to efficiently compute the gradients. The aero-thermal coupling for primal analysis and gradient computation is handled using the OpenMDAO-based MPhys framework. A constant heat source is prescribed for the battery cells, and the battery shape (design variable) is optimized to minimize cooling pump power and battery weight (composite objective function) while keeping the battery temperature below a threshold (constraint). The optimized design achieves a 44.6% and 1.5% reduction in the cooling pump power and battery weight, respectively, and the maximal temperature constraint is satisfied. This work has the potential to reduce battery-pack weight, improve performance, and reduce the weight of thermal management systems for electric vertical take-off and landing aircraft.

thermal management↗
NASA NTRS1937

Research and Design Problems Introduced by Increased Power Output

In what follows the question of the number and geometrical arrangement of the cylinders so important in the design of high performance power units will be considered from various points of view. A discussion will be given of the possibilities of the various working processes and an investigation will be made of possible means for improving the continuous operation and take-off performance, particularly the methods of supercharging, increasing the r.p.m., and employing the two-stroke-cycle engine. Finally, the question of lowered fuel consumption will be gone over briefly. The subject will be treated under four headings: I) Considerations on the engine layout; II) Increase in output per given swept volume; III) Improvement in the take-off performance; IV) Lowering of the fuel consumption.

Kurtz, Oskar↗
NASA NTRS1938

The Aerodynamic Characteristics of Four Full-Scale Propellers Having Different Plan Forms

Tests were made of four propellers, with diameters of 10 feet, having different blade plan forms. One propeller (Navy design no. 5868-r6) was of the usual present-day type and was used as a basis of comparison for the other three, which had unusual plan forms distinguished by the inward (toward the hub) location of the sections having the greatest blade width. It was found that propellers with points of maximum blade width occurring closer to the hub than on the present-day type of blade had higher peak efficiencies but lower take-off efficiencies. This results was found true for a "clean" liquid-cooled engine installation. It appears that some modification could be made to present plan forms which would produce propellers having more satisfactory aerodynamic qualities. The propellers with the inward location of the points of maximum blade width had lower thrust and power coefficients and stalled earlier than the present-day type.

Hartman, Edwin P↗
NASA NTRS1940

Full-Scale Tests of Several Propellers Equipped with Spinners, Cuffs, Airfoil and Round Shanks, and NACA 16-Series Sections, Special Report

Wind-tunnel tests of several propeller, cuff, and spinner combinations were conducted in the 20 foot propeller-research tunnel. Three propellers, which ranged in diameter from 8.4 to 11.25 feet, were tested at the front end of a streamline body incorporating spinners of two diameters. The tests covered a blade angle range from 20 deg to 65 deg. The effect of spinner diameter and propeller cuffs on the characteristics of one propeller was determined. Test were also conducted using a propeller which incorporated aerodynamically good shank sections and using one which incorporated the NACA 16 series sections for the outer 20 percent of the blades. Compressibility effects were not measured, owing to the low testing speeds. The results indicated that a conventional propeller was slightly more efficient when tested in conjunction with a 28 inch diameter spinner than with a 23 inch spinner, and that cuffs increased the efficiency as well as the power absorption characteristics. A propeller having good aerodynamic shanks was found to be definitely superior from the efficiency standpoint to a conventional round-shank propeller with or without cuffs; this propeller would probably be considered structurally impracticable, however. The propeller incorporating the NACA 16 series sections at the tims were found to have a slightly higher efficiency than a conventional propeller; the take-off characteristics appeared to be equally good. The effects noted above probably would be accentuated at helical speeds at which compressibility effects would enter.

Biermann, David↗