Characterization and Advanced Post-Irradiation Examination
Discussion of IMCL Post irradiation examination capabilities at INL.
36 - MATERIALS SCIENCE↗
SEARCH · Engineering Papers
Results for “post irradiation examination”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
AGC-4 Specimen Post-Irradiation Examination Data Interim Report
This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
AGC-4 Specimen Post-Irradiation Examination Data Interim Report
This interim report documents preliminary results of the post-irradiation examination material property testing from the fourth advanced graphite creep (AGC), AGC 4, capsule specimens. This is the fourth of a series of six irradiation test trains planned as part of the AGC experiment to fully characterize the neutron irradiation effects and radiation creep behavior of current nuclear graphite grades to moderate dose levels (=7 dpa). The AGC 4 capsule was irradiated in the Idaho National Laboratory Advanced Test Reactor at a nominal temperature of 800°C and to a peak dose of 8 dpa. Half of the AGC-4 specimens were subjected to compressive stresses to induce irradiation creep. Post-irradiation testing and measurement results are reported with the exception of thermal testing, which is still in progress, and irradiation mechanical strength testing. Additionally, some specimens initially deemed too hot to be examined in the ART Graphite laboratory may still be measured. The data reported includes specimen dimensions for both stressed and unstressed specimens to establish the irradiation creep rates, mass and dimensional data necessary to derive density, elastic constants (Young?s modulus, shear modulus, and Poisson?s ratio) from ultrasonic time of flight velocity measurements, Young?s modulus from the fundamental frequency of vibration, and electrical resistivity. A more complete evaluation of trends in the material property changes, as well as irradiation-induced creep due to the irradiation environment and applied load on the specimens, will be discussed later in AGC 4 post-irradiation examination analysis reports.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
AGR-2 TRISO Fuel Post-Irradiation Examination Final Report
An array of post-irradiation exams and experiments were employed to assess the irradiation performance and high-temperature behavior of AGR-2 UCO TRISO fuel produced in an engineering-scale coater. Work was also conducted on UO2 TRISO fuel produced for comparison with the AGR UCO fuel. Emphases we replaced on enumerating the frequency of SiC layer failures (failure of the SiC layer with at least one PyC layer remaining intact) and TRISO failures (failure of all three dense layers) and evaluating the retention of key fission products within the fuel. Examinations of the fuel kernel and coating morphologies were used to understand the features typical of normal intact fuel, degraded or failed fuel, and mechanisms of degradation. Radiochemical analyses were used to determine their retention within the fuel. The results confirm excellent performance of the fuel that exceeds historical HTGR design requirements with significant margin.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Post-irradiation examination of commercial tantalum alloys following neutron irradiation
Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).
36 MATERIALS SCIENCE↗
Post-irradiation examinations of annular mixed oxide fuels with average burnup 4 and 5% FIMA
In this paper, we present post-irradiation examination results on two type of annular mixed oxide fuel pins irradiated in the Fast Flux Test Facility (FFTF) sodium cooled reactor to an average burnup between 4% and 5% fission of initial heavy atom (FIMA). The pins differed only from the initial Pu content, which was 22 wt% and 26 wt%, respectively. The overall performance of the pins was excellent, in line with previous historical results. The pins with higher Pu content experienced higher irradiation temperatures which influenced the fission gas release, fuel swelling, and Cs distribution compared to the other pins. All the post-irradiation examinations results are discussed against the irradiation parameters. In particular, the pins with higher initial Pu content, i.e., 26 wt%, experienced higher power that resulted in enhanced fission gas release compared to the other two pins with 22 wt% initial Pu content. For the pins with higher fission gas release, onset of Cs redistribution was observed. The two pins that had lower initial Pu content and burnup showed a Cs axial distribution similar to the as-produced one.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Disassembly and Initial Post-Irradiation Examination of the Mini99 Experiment
The Miniature Fuel Molybdenum-99 (Mini99) experiment is a first-of-a-kind experiment in the High Flux Isotope Reactor. Mini99 is the first MiniFuel irradiation experiment to use liquid metal inside the MiniFuel subcapsule for additional temperature control. In this work, the initial post-irradiation examination is reported. As-built simulations were conducted and compared with designs, and physical post-irradiation examinations were conducted to determine actual test temperatures via SiC thermometry samples, to evaluate the extent of fission gas release from the samples, and to remove the fuel from the subcapsules. As-built simulations compared well with experiment designs and were in reasonable agreement with the measured temperatures inferred from the passive SiC thermometers. Additionally, fission gas release values were relatively small (on the order of 3%); one sample reached approximately 8%. Although some of this behavior is attributable to recoil, most of the gas release was likely caused by the physics of the fuel behavior during the test. Finally, disassembly showed that at least four of the fuel samples degraded into small components and granules at some point during the test, with the state of the other two samples unproven. Additional work is planned for further examination of these samples via various microscopy techniques.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Post-Irradiation Examinations of the ATF Experiments - 2020 Status
This report contains the results of post-irradiation examination (PIE) of both Accident Tolerant Fuels-1 (ATF-1) rodlets and ATF-2 rodlets irradiated in the Advanced Test Reactor (ATR). The experiment is part of the U.S. Department of Energy (DOE) Nuclear Technology Research and Development (NTRD) program’s Advanced Fuels Campaign (AFC). The ATF-1 PIE focused on the continuation of the analyses of five rodlets, one containing U 3 Si 2 fuel, two containing UN-U 3 Si 5 composites, and two with UN-U 3 Si 2 composites. The non-destructive examinations of the U 3 Si 2 rodlet showed results comparable to the previously investigated rodlets. The profilometry of the UN-U 3 Si 2 composites highlighted permanent deformation of the cladding at the pellet-pellet interface, suggesting that hourglassing of the composite pellet occurred during irradiation, causing increased localized stresses on the Zirlo cladding tube due to Pellet-Cladding Mechanical Interaction (PCMI). The UN-U 3 Si 5 rodlets, which were contained in Kanthal cladding, did not show enhanced cladding deformation at the pellet interfaces; however, it is to be noted that the initial gap of these two rodlets was larger than typical light water reactor (LWR) gaps. The larger gap might have been sufficient to accommodate the fuel swelling without having contact between the fuel and cladding, explaining the absence of PCMI. Regarding the fission products, no axial redistribution of the major gamma emitters was observed in any of the composite rodlets. Fission gas measurements on the UN-U 3 Si 5 rodlets also has been performed. The estimated fission gas release, based on the calculated fission product inventory, remains limited, with a higher fission gas release for the rodlet that experienced a higher power.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NON-DESTRUCTIVE POST IRRADIATION EXAMINATION OF FIRST CYCLE ACCIDENT TOLERANT AND ADVANCED ZIRCONIUM ALLOY HIGH BURNUP FUEL RODS
Post irradiation examination (PIE) of accident tolerant fuel concepts and high burnup uranium dioxide advanced zirconium alloy clad fuel contribute to near term nuclear industry goals of enhancing light water reactor safety and economics. Westinghouse is developing chromium coated zirconium alloy cladding as an accident tolerant fuel option for current pressurized water reactors. Examination of high burnup fuel further augments the technical foundation for extending the peak rod average burnup limits beyond the current regulatory limit of 62 MWd/kgU. Seven fuel rods were received at the Oak Ridge National Laboratory Irradiated Fuel Examination Facility. This includes three chromium coated zirconium alloy fuel rods and four high burnup advanced zirconium alloy fuel rods. Six of the seven rods were fueled with standard uranium dioxide while one of the chromium coated rods contained Westinghouse’s ADOPT fuel. The overall hot-cell PIE plan and some PIE results have been presented previously. This paper focuses on the additional non-destructive examination and fission gas release. Highlights from visual examination of these rods are presented. The chromium coating showed little to no visual change following irradiation. Observations of the axial burnup trends in the fuel rods are derived from full rod axial gamma-ray scans with additional observations related to local fission product migration. The axial dimensional changes of the seven rods are evaluated. As expected, creep down had not yet occurred in the chromium coated rods, and the maximum diameter strain in the high burnup advanced zirconium alloy cladding was less than 0.5%. Finally, the steady state fission gas release for these rods was measured ranging from 4.1% to 17.6% which matched expectation from literature. These fuel rods now await further destructive examination.
Harp, Jason↗
Post-Irradiation Examination to Quantify Irradiation-Induced Bowing of SiGA® Silicon Carbide Composite Structures (Final CRADA Report – NFE-23-09937)
As part of the SiC-based material development at General Atomics Electromagnetic Systems (GA-EMS), this project involved the first-of-a-kind experimental post-irradiation examination of the irradiation-induced bowing response in SiC composite structures under a neutron flux gradient. The SiC composite miniature channel specimen was provided by GA-EMS for the irradiation experiment. To quantify the irradiation-induced bowing of the channel specimen, a series of visual and dimensional inspections were conducted using the unique capabilities at Oak Ridge National Laboratory (ORNL), including a custom profilometry rig. The post-irradiation examination results of this project will assist GA-EMS in validating their fuel performance model for SiC-based core structures in neutron irradiation environments.
36 MATERIALS SCIENCE↗
Post-irradiation examination of low burnup U 3 Si 5 and UN-U 3 Si 5 composite fuels
Here this work presents post-irradiation examination data on UN-U 3 Si 5 and U 3 Si 5 fuels at low burnup (i.e., <10–15 GWd/tHM) with Kanthal AF® cladding. The results suggest good irradiation performance for both the silicide and nitride-silicide composite pellets. Optical microscopy revealed that the pellet-cladding gap is still open, and limited axial cracking was observed only in UN-U 3 Si 5 pellets. Microcracking was isolated to the U 3 Si 5 phase in all cases and was observed in pre-irradiation and depleted pellets, indicating that it was not irradiation induced. The fission gas release was minimal for the calculated fission density achieved (2.6 – 3.15 × 10 20 fiss/cm 3 ). No fission gas bubbles were observed in the optical metallography. These results suggest acceptable swelling and fission gas behavior for both the single phase and composite compositions.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Irradiation of an enriched uranium (NaCl-UCl 3 ) fuel salt capsule, summary of nondestructive post-irradiation examinations, and solidification modeling
Molten salt reactors (MSRs) are gaining attention due to their potential for safe, carbon-free nuclear energy with reduced waste. However, licensing these reactors is hindered by limited experimental data on fueled salts, both pre- and post-irradiation. Here, the novel Molten-salt Research Temperature-controlled Irradiation (MRTI) vehicle was designed to address knowledge gaps in irradiating enriched‑uranium-bearing salts. The MRTI experiment irradiated 13 cm 3 of UCl₃-NaCl (93 % U-235) salt in the Neutron Radiography (NRAD) Reactor, achieving a burnup of 0.196 GWd/MTU over 390 h. Despite a heater failure, the thermocouple data suggested fission heat kept the salt molten. The MRTI assembly was remotely disassembled for nondestructive post-irradiation examination (PIE), which included precision gamma-ray scanning (PGS) and neutron radiography. Radiograph images showed the location of the salt and the solidification pattern. PGS results provided an early indication that activated materials of construction did not increase in relative intensity in the region of the capsule where the salt was in contact with the material of construction. Additionally, PGS data showed the presence of several gamma emitting fission products, such as Nb-95, Zr-95, Ru-103, Ce-141, and La-140, where Ru-103 had the highest counts at the bottom of the capsule. Computational fluid dynamics modeling supported observations of salt solidification patterns and proved to be a valuable tool to inform PIE activities. The MRTI experiment has thus far provided critical data and lessons learned for fuel salt PIE activities, essential for advancing the technical readiness of MSRs.
11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Post-Irradiation Examination on MiniFuel UCO and UO 2 TRISO Particles Irradiated in HFIR at High Power
Post-irradiation examination (PIE) of MiniFuel compacts was conducted at Oak Ridge National Laboratory (ORNL) under the Nuclear Science User Facilities project in collaboration with Kairos Power (KP) to evaluate the performance of tristructural-isotropic (TRISO) particles under high particle power and fluoride-salt-cooled high-temperature reactor (FHR)-relevant conditions. MiniFuel compacts containing low-enriched uranium oxide-uranium carbide (LEUCO), low-enriched uranium dioxide (LEUO2), and natural UCO (NUCO) kernels were irradiated for four cycles at ORNL’s High Flux Isotope Reactor (HFIR) at target temperatures between 500°C and 900°C. Post irradiation, the experiment was disassembled at ORNL to recover the MiniFuel subcapsules, which were subsequently punctured to measure fission gas release. Subcapsule disassembly allowed the recovery of components of interest, such as silicon carbide (SiC) thermometry, fuel specimens, fission product sinks, and SiC spacers. The experimental irradiation temperature was confirmed by analyzing the SiC thermometry via dilatometry. PIE on the fuel specimens included gamma spectrometry and deconsolidation leach burn leach, which were complemented by imaging techniques such as x-ray computed tomography, optical microscopy, and electron microscopy. The PIE results provide insight into TRISO particle integrity, fission product retention, coating performance, and kernel migration, informing fuel qualification for application in KP’s FHR concept.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Post-Irradiation Examination on MiniFuel UCO and UO 2 TRISO Particles Irradiated in HFIR at High Power
Post-irradiation examination (PIE) of MiniFuel compacts was conducted at Oak Ridge National Laboratory (ORNL) under the Nuclear Science User Facilities project in collaboration with Kairos Power (KP) to evaluate the performance of tristructural-isotropic (TRISO) particles under high particle power and fluoride-salt-cooled high-temperature reactor (FHR)-relevant conditions. MiniFuel compacts containing low-enriched uranium oxide-uranium carbide (LEUCO), low-enriched uranium dioxide (LEUO 2 ), and natural UCO (NUCO) kernels were irradiated for four cycles at ORNL’s High Flux Isotope Reactor (HFIR) at target temperatures between 500°C and 900°C. Post irradiation, the experiment was disassembled at ORNL to recover the MiniFuel subcapsules, which were subsequently punctured to measure fission gas release. Subcapsule disassembly allowed the recovery of components of interest, such as silicon carbide (SiC) thermometry, fuel specimens, fission product sinks, and SiC spacers. The experimental irradiation temperature was confirmed by analyzing the SiC thermometry via dilatometry. PIE on the fuel specimens included gamma spectrometry and deconsolidation leach burn leach, which were complemented by imaging techniques such as x-ray computed tomography, optical microscopy, and electron microscopy. The PIE results provide insight into TRISO particle integrity, fission product retention, coating performance, and kernel migration, informing fuel qualification for application in KP’s FHR concept.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Yttrium Hydride Post Irradiation Examination Plan
The overarching goal of the Department of Energy Office of Nuclear Energy (DOE-NE) microreactor program is to develop technologies for the deployment of civilian microreactors by stakeholders1. Microreactors are expressed as advanced transportable nuclear reactors operating at low power (<20MWth) but high temperatures (>600°C), as well as plug-and-play and inherently safe designs. One prerequisite of a microreactor is the compactness, so that a truck can transport the reactor under safe conditions with the current road infrastructure1,2. The compactness of these reactors likely can be attainable by use of solid components for the essentials of the nuclear core, such as fuel, core heat removal components, reflectors, and moderators. Among these essentials, where fuel enrichment must remain < 20% to meet High Assay Low Enrichment Uranium criteria (HALEU), the largest contribution to the compactness is offered by use of solid moderators which benefit from light atomic weight elements, such as hydrogen, carbon, and beryllium2. Among these, hydrogen-bearing materials, such as metal hydrides, are superior to other options from the lowest critical mass standpoint. Noting that, factors other than critical mass should be considered for a specific reactor design. Yttrium- or zirconium-based metal hydrides have been down-selected due to their neutronic performance. In addition to the neutronic perspective, maintaining hydrogen within the metal hydride is important at the high operating temperatures proposed by advanced reactors. Yttrium hydride (YHx) is, therefore, a proposed moderator material that offers better hydrogen retention at higher operating temperatures than zirconium hydrides due to higher retention and thermal stability of hydrogen in the metal3. The irradiated materials properties of metal hydrides, in this case YHx, must be assessed for the qualification of these moderators. Material testing and inspection processes must illustrate that the effects of dimensional and property changes on thermophysical and mechanical properties do not cause any significant changes on the microreactor safety, and the moderating power is maintained within design limits. Thus, the effect of irradiation on the thermophysical and mechanical properties must be determined. This post-irradiation examination (PIE) plan specifically aims to determine these properties for YHx following Advanced Test Reactor (ATR) irradiation.
99 GENERAL AND MISCELLANEOUS↗
PLN-6268 Yttrium Hydride Post Irradiation Examination Plan
The overarching goal of the Department of Energy Office of Nuclear Energy (DOE-NE) microreactor program is to develop technologies for the deployment of civilian microreactors by stakeholders1. Microreactors are expressed as advanced transportable nuclear reactors operating at low power (<20MWth) but high temperatures (>600°C), as well as plug-and-play and inherently safe designs. One prerequisite of a microreactor is the compactness, so that a truck can transport the reactor under safe conditions with the current road infrastructure1,2. The compactness of these reactors likely can be attainable by use of solid components for the essentials of the nuclear core, such as fuel, core heat removal components, reflectors, and moderators. Among these essentials, where fuel enrichment must remain < 20% to meet High Assay Low Enrichment Uranium criteria (HALEU), the largest contribution to the compactness is offered by use of solid moderators which benefit from light atomic weight elements, such as hydrogen, carbon, and beryllium2. Among these, hydrogen-bearing materials, such as metal hydrides, are superior to other options from the lowest critical mass standpoint. Noting that, factors other than critical mass should be considered for a specific reactor design. Yttrium- or zirconium-based metal hydrides have been down-selected due to their neutronic performance. In addition to the neutronic perspective, maintaining hydrogen within the metal hydride is important at the high operating temperatures proposed by advanced reactors. Yttrium hydride (YHx) is, therefore, a proposed moderator material that offers better hydrogen retention at higher operating temperatures than zirconium hydrides due to higher retention and thermal stability of hydrogen in the metal3. The irradiated materials properties of metal hydrides, in this case YHx, must be assessed for the qualification of these moderators. Material testing and inspection processes must illustrate that the effects of dimensional and property changes on thermophysical and mechanical properties do not cause any significant changes on the microreactor safety, and the moderating power is maintained within design limits. Thus, the effect of irradiation on the thermophysical and mechanical properties must be determined. This post-irradiation examination (PIE) plan specifically aims to determine these properties for YHx following Advanced Test Reactor (ATR) irradiation.
99 GENERAL AND MISCELLANEOUS↗
ORNL Post-irradiation Examination (LAMDA) Final Report on Characterization of Irradiated Grade 92 Ferritic-Martensitic Steels
Irradiation effects on ferritic-martensitic steel Grade 92 were investigated in this project. Samples from two heats of Grade 92, i.e., G92-2b and NF616, were selected, which were irradiated in the High Flux Isotope Reactor (HFIR) and the Advanced Test Reactor (ATR), respectively. Samples from two heats of ferriticmartensitic steel T91, irradiated in the ATR, were also selected as references for the Grade 92 samples. The selected G92-2b samples were irradiated to 0.5–14.7 displacements per atom (dpa) at two temperature regimes: 400–497 °C and 683–720°C. The selection of the high irradiation temperatures up to ~720°C is to test the performance at such upper bound temperatures, which would provide insights for the upper bound applicable temperature for Grade 92. The selected NF616 and T91 samples were irradiated to 3–8.2 dpa at 292–448°C. Except for T91 heat2 samples in 3-mm diameter discs, all the other selected samples are of type SS-J2 miniature tensile specimens. Two Nuclear Science User Facilities (NSUF), i.e., the Irradiated Materials Examination and Testing (IMET) hot cell facility and the Low Activation Materials Design and Analysis (LAMDA) facility, were used in the Post-Irradiation Examination (PIE) activities for the selected samples, which include: Tensile tests at room temperature (IMET); Fractography of the tensile fracture surfaces (LAMDA: scanning electron microscopy and energy; dispersive spectroscopy); Vickers hardness measurements (LAMDA); and Microstructural characterization (LAMDA: electron backscatter diffraction, focused-ion beam, and transmission electron microscopy).
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Quantifying dislocation-type defects in post irradiation examination via transfer learning
The quantitative analysis of dislocation-type defects in irradiated materials is critical to materials characterization in the nuclear energy industry. The conventional approach of an instrument scientist manually identifying any dislocation defects is both time-consuming and subjective, thereby potentially introducing inconsistencies in the quantification. This work approaches dislocation-type defect identification and segmentation using a standard open-source computer vision model, YOLO11, that leverages transfer learning to create a highly effective dislocation defect quantification tool while using only a minimal number of annotated micrographs for training. This model demonstrates the ability to segment both dislocation lines and loops concurrently in micrographs with high pixel noise levels and on two alloys not represented in the training set. Inference of dislocation defects using transmission electron microscopy on three different irradiated alloys relevant to the nuclear energy industry are examined in this work with widely varying pixel noise levels and with completely unrelated composition and dislocation formations for practical post irradiation examination analysis. Code and models are available at https://github.com/idaholab/PANDA.
36 MATERIALS SCIENCE↗