Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ports”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

An investigation at static conditions of nonaxisymmetric nozzle thrust reverser port geometry including effects of rounding and rotating the port corner

An investigation has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the effects of rounding and rotating the port corner of a nonaxisymmetric thrust reversing port. High pressure air was used to simulate jet exhaust at nozzle pressure ratios up to 6.0. The investigation indicates that using a rounded corner in the reverser port passage increases the discharge coefficient significantly compared to that of a sharp cornered thrust reversing port. Incorporating a rotating cylinder into the rounded corner reverser port passage provides no additional increase at cylinder revolutions per minute up to 10,000. (Revolutions per minute of 390,000 were necessary to achieve a surface velocity equal to the duct velocity.) Highest levels of discharge coefficient are obtained by providing a large, round, cylindrical surface in the port upstream wall. Locating the reverser port in a constant area duct results in higher discharge coefficients than locating the port in a convergent duct.

Arbiter, D. G.↗
NASA NTRS1989

W-band six-port network analyzer for two-port characterization of millimeter wave transistors

A W-band (75-100 GHz) six-port junction network analyzer was constructed from commercially available descrete waveguide components and was used for the direct two-port S-parameter measurement of active three-terminal devices. A comparison between the six-port and a down-converter-type frequency extender for a conventional network analyzer revealed the superior performance of the six-port. The application of the six-port to characterize a 0.1-micron gate-length HEMT at W-band is described, and representative results are presented.

Moeller, Karl J.↗
NASA NTRS1985

Port geometry effects on thrust reverser static performance

An investigation has been conducted to provide some insight into the effect of several geometric parameters on the internal performance of thrust reverser ports for nonaxisymmetric nozzles using a single port test apparatus. This test apparatus simulates thrust reversal (conceptually) which would occur in the convergent section of the forward flight nozzle or in the constant area duct just upstream. The port opening had an aspect ratio of 6.1 (throat width/throat height) and had constant passage area from the geometric throat to the exit. The geometric parameters investigated were port angle, port corner radius, port location, and flow blocker angle. The apparatus had a single port so that thrust (vector) angle could be obtained from force balance measurements. The tests were conducted in the Static Test Stand of the Langley 16-Foot Transonic Tunnel at nozzle pressure ratios from 1.5 to 8.0 using high pressure air for propulsion simulation. Port angles (measured forward from a horizontal reference line) investigated were 75, 90, 120 and 135 deg. Sharp and rounded port corners were investigated for each port angle. Discharge coefficient, thrust ratio, and passage static pressures were measured.

Re, R. J.↗
NASA NTRS1987

Effect of varying internal geometry on the static performance of rectangular thrust-reverser ports

An investigation has been conducted to evaluate the effects of several geometric parameters on the internal performance of rectangular thrust-reverser ports for nonaxisymmetric nozzles. Internal geometry was varied with a test apparatus which simulated a forward-flight nozzle with a single, fully deployed reverser port. The test apparatus was designed to simulate thrust reversal (conceptually) either in the convergent section of the nozzle or in the constant-area duct just upstream of the nozzle. The main geometric parameters investigated were port angle, port corner radius, port location, and internal flow blocker angle. For all reverser port geometries, the port opening had an aspect ratio (throat width to throat height) of 6.1 and had a constant passage area from the geometric port throat to the exit. Reverser-port internal performance and thrust-vector angles computed from force-balance measurements are presented.

Re, Richard J.↗
NASA NTRS1989

Design issues in 2-port network models of bilateral remote manipulation

A two-port impedance-network model of a single-degree-of-freedom remote manipulation system in which a human operator at the master port interacts with a task object at the slave port in a remote location is presented. The design of the network involves the selection of feedback gains for the servomechanisms that transmit motion and force information from one port of the two-port to the other in both directions. The proposed methodology allows this selection to be based on both stability requirements and specifications of desired port impedances, given models of the task and the human operator. The resulting design guidelines guarantee stability for any passive task object at the slave port and any passive human impedance at the master port.

Raju, G. Jagannath↗
NASA NTRS1987

An analytical and experimental study of injection-locked two-port oscillators

A Ku-band IMPATT oscillator with two distinct output power ports was injection-locked alternately at both ports. The transmission locking bandwidth was nearly the same for either port. The lower free running power port had a reflection locking bandwidth that was narrower than its transmission locking one. Just the opposite was found at the other port. A detailed analytical model for two-port injection-locked oscillators is presented, and its results agree quite well with the experiments. A critique of the literature on this topic is included to clear up misconceptions and errors. It is concluded that two-port injection-locked oscillators may prove useful in certain communication systems.

Freeman, Jon C.↗
NASA NTRS1938

Scavenging a Piston-ported Two-stroke Cylinder

An investigation was made with a specially designed engine to determine the scavenging characteristics of a large number of inlet-port shapes and arrangements and the optimum port arrangement and timing for this particular type of engine. A special cylinder construction permitted wide variations in timing for this particular type of engine. A special cylinder construction permitted wide variations in timing as well as in shape and arrangement of both the inlet and exhaust ports. The study of the effect of port shape combinations and timings on engine performance was made using illuminating gas as a fuel. Through variations in inlet-port arrangement and port timings, the value of the scavenging efficiency was increased from an original 44 percent to approximately 67 percent with a corresponding increase in power. With the optimum port arrangement and timing determined, a large number of performance runs were made under both spark-ignition and compression-ignition operation.

Rogowski, A R↗
NASA NTRS1994

Design and evaluation of candidate pressure ports for the HYFLITE experiment

A concept for placing a pressure transducer directly in a shuttle type tile was developed at Langley Research Center. A 5 inch long quartz with a .020 inch inner diameter provides the thermal isolation necessary to allow 2800 F surface pressure measurements to be taken by pressure transducer rated at 250 F. The assembly is potted in place with RTV 560 in a piece of FRCI-12 thermal protection system insulation tile. The integrity of the thermal protection system is maintained even with the intrusion of the pressure port assembly and the pressure port does not disrupt the air flow across the lifting body. Approximately 200 of these pressure ports are to be used in each of the Hypersonic Flight Experiment (HYFLITE) flight tests. Initial vibroacoustic and aerothermal testing of the pressure port designs have been completed at Langley Research vibration laboratory and the 20 MWatt 2 x 9 turbulent duct facility at Ames Research Center. The performance of the pressure ports were found to be well within the required design limits for all cases. In addition, a failure mode in which the entire pressure port assembly was removed proved to be a begin case.

Teter, John E., Jr.↗
NASA NTRS1977

Determination of burning area and port volume in complex burning regions of a solid rocket motor

An analysis of the geometry of the burning in both star-cylindrical port interface regions and regions of partially inhibited slots is presented. Some characteristics parameters are defined and illustrated. Methods are proposed for calculating burning areas which functionally depend only on the total distance burned. According to this method, several points are defined where abrupt changes in geometry occur, and these are tracked throughout the burn. Equations are developed for computing port perimeter and port area at pre-established longitudinal positions. Some common formulas and some newly developed formulas are then used to compute burning surface area and port volume. Some specific results are presented for the solid rocket motor committed to the space shuttle project.

Kingsbury, J. A.↗
NASA NTRS1978

Commercial Fishing Port Development in North Florida

The author has identified the following significant results. Seven major counties were examined: Escambia, Bay, Gulf, Franklin, Wakulla, Nassau, and Duval. Population and economic activity were reviewed, along with commercial fishing and port facilities. Recommendations for five northwest Florida counties were based on interpretation of aerial photographs, satellite imagery, an aerial survey site visit, and published data. Major needs in Pensacola included docking, ice supply, and net and engine repair services. Costs for additional docks, an ice plant, and gear storage were estimated at $3,658,600. Port users in Panama City identified additional docking and gear storage as primary needs, along with gear repair and a marine railway. Estimated costs for dock and gear storage were $2,860,000. Added docking, gear storage, and ice supply, as well as gear electronics and diesel repair were needed in Port St. Joe. Costs were calculated at $1,231,500. Franklin County has three ports (Apalachicola - $1,107,000 for docks and gear storage, Eastpoint - $420,000 for additional docks, and Carrabella - $2,824,100 for docks, gear storage, and ice plant).

Mathis, K.↗
NASA NTRS1986

Effect of port corner geometry on the internal performance of a rotating-vane-type thrust reverser

An investigation has been conducted in the static-test facility of the Langley 16-Foot Transonic Tunnel to determine the effects of reverser port geometry on the internal performance of a nonaxisymmetric rotating-vane-type thrust reverser. Thrust reverser vane positions representing a spoiled-trust (partially deployed) position and a full-reverse-thrust (fully deployed) position were tested with each port geometry variable. The effects of upstream port corner radius and wall angle on internal performance were determined. In addition, the effect of the length of a simulated cooling liner (blunt-base step) near the reverser port entrance was investigated; five different lengths were tested. All tests were conducted with no external flows, and nozzle pressure ratio was varied from 1.2 to 5.0.

Berrier, B. L.↗
NASA NTRS1991

Quad-Port Transceivers For A Dual-CRR LAN

Quad-port fiber-optic transceivers demonstrated successfully as physical-layer interface units in WhisperNet - local-area network (LAN) of computers and other devices in communication with each other. Each node of Dual-CRR LAN contains quad-port transceiver serving four pairs of optical fibers. Quad-port transceiver consists of two dual-port transceivers and ancillary equipment in compact package. Transceiver serves as interface between optical fibers and external computing devices. Because of high reliability, availability and "fail-soft" nature, network well suited to military and critical commercial applications.

Wiencko, Joseph A., Jr.↗
NASA NTRS1974

Maximum power transfer in n ports with passive loads

The problem of drawing maximum power from an n port by suitably terminating it with another passive n port is studied. Methods are derived for determining sets of passive impedance matrices which are 'optimal' in the sense that they draw maximum power from a given n port. It is shown that, in all nontrivial cases, if there exists any (passive or otherwise) optimum-load impedance matrix, then there exist, in fact, infinitely many passive optimum-load impedance matrices.

Vidyasagar, M.↗
NASA NTRS1986

Variable Control Port for Fluidic Control Device

Volume and velocity of control flow independently adjustable. In proposed device rotatable D-shaped control sector throttles down control port or open it completely and set to any intermediate control-port crosssectional area. Although adjustment affects volume and control-port head loss, volume and velocity controlled independently by also adjusting fluidsupply pressure. Allows adjustment to wider range of control conditions and ability to maximize control efficiency. Fluidic control theory suggests possibility of improvement in control ratio of at least 2:1 over conventional devices.

Collins, Earl R., Jr.↗
NASA NTRS1991

Experiences in porting NASTRAN (R) to non-traditional platforms

The 1990 UNIX version of NASTRAN was ported to two new platforms that are not supported by COSMIC: the Sun SPARC workstation and the Apple Macintosh using the A/UX version of UNIX. The experiences of the authers in porting NASTRAN is summarized here. Suggestions for users who might attempt similar ports are given.

Davis, Gregory L.↗
NASA NTRS1993

Maximum and minimum return losses from a passive two-port network terminated with a mismatched load

This article presents an analytical method for determining the exact distance a load is required to be offset from a passive two-port network to obtain maximum or minimum return losses from the terminated two-port network. Equations are derived in terms of two-port network S-parameters and load reflection coefficient. The equations are useful for predicting worst-case performances of some types of networks that are terminated with offset short-circuit loads.

Otoshi, T. Y.↗