Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks

Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young’s modulus and ~100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. Here, the interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Advances in additive manufacturing, materials, and applications with AI/ML

There is high interest in making digital manufacturing a central facet of the new manufacturing landscape. However, in the materials science world, there is much work and opportunity to realize the full potential of artificial intelligence/machine learning (AI/ML) with regard to the structure–composition–processing–property (SCPP) relationship. For polymers (thermoplastics, thermosets, elastomers) and composites (nanocomposites), the origin of their high performance and even recyclability starts with design and formulation. Processing methods enable more property development based on curing, shape-factor forming, and anisotropic directionality. In subtractive manufacturing, high-performance and engineering polymers can be shaped and milled to very high tolerance and specifications and used as replacements for metals and alloys. In conclusion, this typically relies on digital manufacturing methods but tends to be wasteful in materials.

Lara-Ceniceros, Tania E. [Centro de Investigación ↗
DOE OSTI2025

Atomically Fine-Tuning Organic–Inorganic Carbon Molecular Sieve Membranes for Hydrogen Production

Polymeric membranes with great processability are attractive for the H 2 /CO 2 separation required for hydrogen production from renewable biomass with carbon capture for utilization and sequestration. However, it remains elusive to engineer polymer architectures to obtain desired sub-3.3 Å ultramicropores to efficiently sieve H 2 from CO 2 . Herein, we demonstrate a scalable way of carbonizing polybenzimidazole (PBI) at low temperatures, followed by vapor phase infiltration (VPI) to atomically narrow ultramicropores throughout the films, forming hybrid organic–inorganic carbon molecular sieves (CMSs). One VPI cycle (100 s) for the PBI carbonized at 500 °C remarkably increases H 2 /CO 2 selectivity from 9.6 to 83 at 100 °C, surpassing Robeson’s upper bound. The CMS demonstrates a stable H 2 /CO 2 separation performance when challenged with simulated syngas streams and can be fabricated into thin-film composite membranes, outperforming state-of-the-art membranes. Finally, the scalable approach can be ubiquitous to molecularly fine-tune ultramicropores of leading polymeric membranes to further improve their size-sieving ability and thus separation efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Single‐Step Recovery of Water from Stable Crude Oil‐Water Emulsion Using Surface Engineered Hybrid Inorganic‐Polymer Membranes

ABSTRACT Separating crude oil from water remains one of the most stubborn challenges in environmental remediation, especially for surfactant‐stabilized emulsions that resist conventional demulsification methods. Here, we report a scalable strategy for achieving near‐zero‐discharge separation of crude oil emulsions using a single superhydrophilic membrane. By applying low‐temperature atomic layer deposition (ALD) of various metal oxides onto activated polyvinylidene fluoride (PVDF) membranes, we create atomically precise surface‐engineered (SE) membranes that maintain an exceptionally strong hydration layer at the membrane‐feed interface, even at high oil loadings. Among the various metal oxides, TiO 2 ‐modified SE membranes exhibit superior interfacial water stability, enabling sustained dewatering of complex crude oil‐water emulsions with >98% separation efficiency and >97% water recovery, compared to only 24.6% water recovery for the pristine membrane. This separation performance surpasses conventional hydrophilic membranes and is comparable to complex Janus channel membrane systems, demonstrating near‐complete emulsion separation using a single membrane. This low‐temperature membrane surface engineering process with atomic‐level precision and potential for scalability via roll‐to‐roll fabrication is promising for industrial‐scale, energy‐efficient water treatment and oil spill remediation applications.

Sengupta, Bratin [Applied Materials Division Argon↗
DOE OSTI2025

Enhancing Thermal Transport in Polymeric Composites Via Engineered Noncovalent Filler–Polymer Interactions

Understanding thermal transport mechanisms in polymeric composites allows us to expand the boundaries of thermal conductivity in them, either increasing it for more efficient heat dissipation or decreasing it for better thermal insulation. But, these mechanisms are not fully understood. Systematic experimental investigations remain limited. Practical strategies to tune the interfacial thermal resistance (ITR) between fillers and polymers and the thermal conductivity of composites remain elusive. Here, we studied the thermal transport in representative polymer composites, using polyethylene (PE) or polyaniline (PANI) as matrices and graphite as fillers. PANI, with aromatic rings in its backbone, interacts with graphite through strong noncovalent π–π stacking interactions, whereas PE lacks such interactions. We can then quantify how π–π stacking interactions between graphite and polymers enhance thermal transport in composites. PE/graphite and PANI/graphite composites with the same 1.5% filler volume fractions show a ∼22.82% and ∼34.85% enhancement in thermal conductivity compared to pure polymers, respectively. Calculated ITRs in PE/graphite and PANI/graphite are ~6 x 10 -8 m 2 KW -1 and ~1 x 10 -8 m 2 KW -1 , respectively, highlighting how π–π stacking interactions reduce ITR. Molecular dynamics (MD) simulations suggest that π–π stacking interactions between PANI chains and graphite surfaces enhance alignment of PANI's aromatic rings with graphite surfaces. This allows more carbon atoms from PANI chains to interact with graphite surfaces at a shorter distance compared to PE chains. Finally, our work indicates that tuning the π–π stacking interactions between polymers and fillers is an effective approach to reduce the ITR and enhance the thermal conductivity of composites.

atoms↗
DOE OSTI2025

Giant Electrostriction via Nanodomain Engineering in Relaxor Ferroelectric Polymers

Relaxor ferroelectric (RFE) polymers hold great promise for artificial muscles due to their high actuation strain, high loading stress, and fast response. However, the structural origin underlying their large electrostrictive deformation remains elusive. In this study, we investigate poly(vinylidene fluoride-co-trifluoroethylene) [P(VDF-TrFE)]-based RFE terpolymers, incorporating 1,1-chlorofluoroethylene (CFE) or chlorotrifluoroethylene (CTFE) (the terpolymers are denoted as terP-CFE and terP-CTFE, respectively) as termonomers. Although both terpolymers show similar semicrystalline morphology, drastically different electrostrictive properties are observed. Specifically, the terP-CFE annealed at 100 °C achieves a record-high transverse strain of ∼10.6%, whereas 100 °C-annealed terP-CTFE only shows a much lower actuation strain of ∼4.2% at the same poling field of 190 MV/m. To elucidate the origin of this difference, time-resolved wide-angle X-ray diffraction, small-angle X-ray scattering, and Fourier transform infrared experiments are performed during in situ electric poling. An RFE-to-ferroelectric (FE) crystal phase transition is observed for terP-CFE but is absent for terP-CTFE. Beyond the contribution of the crystalline phase, the oriented amorphous fraction and crystalline defects (e.g., taut-tie molecules) also play significant roles in enhancing electrostriction. In conclusion, this mechanistic insight provides a valuable foundation for the rational design of next-generation RFE polymers with tunable properties through defect engineering of their semicrystalline structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Correlating processing variables to material properties in recycled polypropylene: A data‐driven approach

Abstract Polypropylene (PP) is one of the most widely used plastics, yet its recycling remains limited, with less than 1% of solid waste PP being reprocessed. Mechanical recycling through extrusion is the most practical method, but inconsistent reprocessing conditions introduce variability in material properties. While temperature, screw speed, and residence time influence the thermomechanical stress applied during reprocessing, there are no standardized guidelines for optimizing these parameters. This study examines how these factors shape the properties of recycled PP, using conditions designed to mimic post‐industrial recycled (PIR) scrap. Residence time was measured using colorimetric tracking and correlated with molecular weight, viscosity, and mechanical properties over multiple extrusion cycles. Data‐driven modeling, including response surface methodology, support vector machines, and artificial neural networks, identified processing temperature as the dominant factor in material degradation, followed by residence time. Mechanical properties remained stable, while viscosity decreased predictably with increasing residence time. By linking reprocessing conditions to property evolution, this study provides a method to optimize processing parameters and reduce variability in recycled PP. These findings help manufacturers improve process control, making recycled PP more predictable for reuse in manufacturing. Highlights Study of PIR‐quality PP without additives or compatibilizers. Residence time analysis shows processing temperature drives PP property changes. Mark‐Houwink enables quick molecular weight checks for quality control. Models predict mechanical and rheological shifts in reprocessing. Optimized processing parameters minimize property degradation in recycling.

Estela‐García, John E. [Polymer Engineering Center↗
DOE OSTI2025

Topology-Dependent Polymer Stretching and Scission in Solution at Extreme Shear Rates

There has been significant interest in the engineering of polymer topology to control rheology and mechanical stability in dilute solutions for applications involving extreme shear rate flows. However, methods to experimentally probe properties at relevant shear rates (≈ 10 4 –10 6 s –1 ) have remained ex situ, obscuring access to measures of polymer deformation and rheology that would otherwise provide mechanistic insight into the topology-dependent properties that control their behavior in extreme shear flows. In this study, we used novel in situ small angle neutron scattering measurements in a capillary rheometer (capillary rheo-SANS) to simultaneously measure solution viscosities and polymer deformations in high shear on a series of chemically homologous topology-defined polymers including linear, randomly branched, and star-shaped molecules. We demonstrate that differences in the onset of chain stretching and shear thinning of these polymers in dilute solution are controlled primarily by differences in their molecular relaxation time. These differences correlate with differences in chain scission inferred from ex situ measurements at more extreme shear rates. Together, the results demonstrate a direct coupling between chain deformation and scission, and suggest that the dominant effect of branching as a means to impart resilience against mechanical degradation is through differences in relaxation dynamics due to branching. We anticipate that these results will provide key insights to engineer topology-controlled polymers for rheological modification, mechanical stability, and controlled mechano-chemistry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Extreme Nanoconfinement Dramatically Enhances Small Molecule Solubility in Nonpolar Polymers

Elucidating gas solubility in confined polymer systems addresses a fundamental gap in polymer physics and has important implications for gas barrier and separation technologies and polymer upcycling reactions. In this study, we examine the solubility of methanol and n-hexane in polystyrene and low-density polyethylene confined within the interstitial pores of disordered silica nanoparticle packings. Using capillary rise infiltration, these polymers are infiltrated into the nanoparticle packings. Gas solubility in these confined polymers is measured using a quartz crystal microbalance. Remarkably, confinement leads to a 10- to ∼100-fold increase in gas solubility. Systematic experiments reveal that pore size plays a dominant role in increasing solubility. In contrast, the molecular weight of the polymer and the surface wetting characteristics of the nanoparticles, achieved by hydrophobically modifying the nanoparticles, have minimal effects. By systematically varying penetrant polarity, polymer crystallinity, pore size, and nanopore surface chemistry, this study isolates geometric nanoconfinement as the dominant factor governing solubility enhancement in confined polymers. Atomistic simulations revealed that confinement and surface−polymer interactions both contribute to enhanced solubility, with polymer packing playing a significant role in modulating gas uptake. Here, these results suggest that the changes in the molecular arrangements of polymer segments underlie the observed trends. This study highlights the potential of confined polymers in engineering the separation performance of membranes and heterogeneously catalyzed polymer upcycling reactions.

alcohols↗
DOE OSTI2025

Solvent-based plastic recycling technologies

Solvent-based recycling approaches are receiving industrial and academic interest for their ability to produce high-quality plastic resins from a variety of plastic waste sources without breaking the polymer chains. Here we highlight the development of solvent-based technologies, focusing on the underlying principles, techno-economic and life-cycle analyses, and commercialization. The basic steps in solvent-based recycling include plastic size reduction, plastic dissolution, filtration or centrifugation, and optional additional cleaning steps such as adsorption, precipitation and solvent removal. Impurities that build up in the solvent must also be removed. The goal of solvent-based technologies is to produce a high-quality resin without plastic contaminants or other added substances. Disadvantages of these solvent-based technologies are their physicochemical complexity and the difficulty in scaling up to achieve continuous operations with high polymer and solvent yields and throughputs. As a result, chemical engineering is thus critical in bringing solvent-based recycling technologies to market.

Chemical engineering↗
DOE OSTI2025

An elastin-like polymer targeting vascular endothelial growth factor receptor-1 reduces survival in serum-starved endothelial cells

Peptides often exhibit biological activity that depends on the context in which they are displayed and delivered. Understanding and controlling these contextual effects on peptide function is critical for designing targeted and responsive peptide-based biomaterials and therapeutics. Genetically engineered protein polymers such as elastin-like polypeptides (ELPs) can incorporate bioactive peptide motifs and are attractive candidates for biomaterials used in tissue engineering and targeted drug delivery. They also present an opportunity for investigating and modulating cell signaling pathways by presenting a peptide ligand in various defined chemical and physical environments. Vascular endothelial growth factor receptor-1 (VEGFR1) signaling plays important and complex roles in cell survival and angiogenesis, but polymeric materials that interact with this signaling axis are scarce. In this study, a novel genetically engineered elastin-like polymer that targets VEGFR1 is characterized. This polymer, termed R1B-ELP, binds to human endothelial cells in a manner dependent on its VEGFR1-targeting motif and, based on cell proliferation and cytotoxicity assays, demonstrates activity consistent with disrupting pro-survival signaling necessary for endothelial cell function under conditions of environmental stress. Notably, these findings indicate that ELP fusion alters the functional behavior of the targeting peptide. Modulators of VEGFR1 signaling have potential applications in basic studies of angiogenesis as well as in therapeutic applications targeting vascular or inflammatory diseases.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Engineering a biopolymer for vascular embolization based on fundamental polymer principals

Herein we describe the engineering of a potential polymer substitute to metal coils for achieving vascular embolization. Our system is based on a methacrylate end-functionalized polyethylene oxide-polypropylene oxide-polyethylene oxide (PEO-PPO-PEO) triblock copolymer which displays thermal-reversible gelation properties and FCC ordering of the original copolymer while also being able to chemically crosslink. This system shows injectability, two-step gelation, chemical crosslinking with a five-fold increase in modulus and is highly resistant to washout under physiological flow conditions. Furthermore, we show that exposure to aqueous flow imparts resistance to swelling where less than 10 % swelling was observed under physiological flow as opposed to more than 60 % under static conditions after 30 days. Auxiliary experiments with PEO-PPO-PEO copolymers of various molecular weights indicate that this phenomenon may possibly be attributed to entanglements known to occur between adjacent micelles, where the reptation time, the time for polymer disentanglement, is long compared to the flow rate.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tunable Crosslinked Ether Polymer Network Electrolytes for High‐Performance All‐Solid‐State Sodium Batteries

All-solid-state batteries (ASSBs) are critical for achieving high energy density and enhanced safety. Solid polymer electrolytes (SPEs) offer key advantages over other electrolytes, including improved safety, flexibility, and interfacial contact. Among the SPEs, ether-based polymers are widely studied due to their ease of processing and high ionic conductivity (σi) in the amorphous state. In this work, the introduction of poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) into an SPE matrix composed of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) (PEG2k), and sodium bis(fluorosulfonyl)imide (NaFSI) salt is investigated to facilitate the formation of amorphous, high σ i SPEs through end-group engineering and polymer ratio optimization. PEGMEMA enhances structural integrity via crosslinking with PEGDA through its methacrylate group, while its methyl end group aids ion conduction. A 2:1:7 ratio of PEGDA:PEGMEMA:PEG2k exhibits a σi of 1.16 x 10 -4 S cm -1 and oxidative stability up to 4.4 V at 60 °C. A solid-state cell incorporating this SPE, a Na 2/3 Ni 1/3 Mn 2/3 O 2 (NM12) cathode, and a sodium-metal anode demonstrates excellent cycling stability, retaining over 80 % of its initial capacity for 150 cycles at 60 °C. The findings highlight the potential of end-group engineering in improving the electrochemical performance of SPEs.

25 ENERGY STORAGE↗
DOE OSTI2024

Recycling polyolefin plastic waste at short contact times via rapid joule heating

Abstract The chemical deconstruction of polyolefins to fuels, lubricants, and waxes offers a promising strategy for mitigating their accumulation in landfills and the environment. Yet, achieving true recyclability of polyolefins into C 2 -C 4 monomers with high yields, low energy demand, and low carbon dioxide emissions under realistic polymer-to-catalyst ratios remains elusive. Here, we demonstrate a single-step electrified approach utilizing Rapid Joule Heating over an H-ZSM-5 catalyst to efficiently deconstruct polyolefin plastic waste into light olefins (C 2 -C 4 ) in milliseconds, with high productivity at much higher polymer-to-catalyst ratio than prior work. The catalyst is essential in producing a narrow distribution of light olefins. Pulsed operation and steam co-feeding enable highly selective deconstruction (product fraction of >90% towards C 2 -C 4 hydrocarbons) with minimal catalyst deactivation compared to Continuous Joule Heating. This laboratory-scale approach demonstrates effective deconstruction of real-life waste materials, resilience to additives and impurities, and versatility for circular polyolefin plastic waste management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Reversible two-way tuning of thermal conductivity in an end-linked star-shaped thermoset

Polymeric thermal switches that can reversibly tune and significantly enhance their thermal conductivities are desirable for diverse applications in electronics, aerospace, automotives, and medicine; however, they are rarely achieved. Here, we report a polymer-based thermal switch consisting of an end-linked star-shaped thermoset with two independent thermal conductivity tuning mechanisms—strain and temperature modulation—that rapidly, reversibly, and cyclically modulate thermal conductivity. The end-linked star-shaped thermoset exhibits a strain-modulated thermal conductivity enhancement up to 11.5 at a fixed temperature of 60 °C (increasing from 0.15 to 2.1 W m –1 K –1 ). Additionally, it demonstrates a temperature-modulated thermal conductivity tuning ratio up to 2.3 at a fixed stretch of 2.5 (increasing from 0.17 to 0.39 W m –1 K –1 ). When combined, these two effects collectively enable the end-linked star-shaped thermoset to achieve a thermal conductivity tuning ratio up to 14.2. Moreover, the end-linked star-shaped thermoset demonstrates reversible tuning for over 1000 cycles. The reversible two-way tuning of thermal conductivity is attributed to the synergy of aligned amorphous chains, oriented crystalline domains, and increased crystallinity by elastically deforming the end-linked star-shaped thermoset.

42 ENGINEERING↗