Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plasma conditions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Ground-Based Simulation of Low-Earth Orbit Plasma Conditions: Plasma Generation and Characterization

A 16-cm diameter plasma source operated on argon is described that is capable of producing a plasma environment that closely simulates the low Earth orbit (LEO) conditions experienced by satellites in the altitude range between 300 to 500 km. The plasma source uses a transverse-field magnetic filter, and has been successful in producing low electron temperature plasmas that contain streaming ion populations. Both of these characteristics are important because the plasma in LEO is relatively cold (e.g., Te approx. 0.1 eV) and the ram energy of the ions due to the motion of the satellite relative to the LEO plasma is high (e.g., 7,800 m/s which corresponds to approx. 5 eV for O+ ions). Plasma source operational conditions of flow rate and discharge power are presented that allow the electron temperature to be adjusted over a range from 0.14 to 0.4 eV. The expanding plasma flow field downstream of the source contains both low-energy, charge-exchange ions and streaming ions with energies that are adjustable over a range from 4 eV to 6 eV. At low flow rates and low facility pressures, the streaming ion component of the ion population comprises over 90% of the total plasma density. In the work described herein, a large area retarding potential analyzer was used to measure both electron and ion energy distribution functions in the low density, expanding plasma produced downstream of the plasma source. The benefits of using this type of plasma diagnostic tool in easily perturbed, low-density plasma are identified, and techniques are also discussed that can be used to perform real-time measurements of electron temperature. Finally, recommendations are made that may enable lower electron temperatures to be produced while simultaneously decreasing the plasma source flow rate below 1 to 2 sccm.

Williams, John D.↗
DOE OSTI2022

A case study of using x-ray Thomson scattering to diagnose the in-flight plasma conditions of DT cryogenic implosions

The design of inertial confinement fusion ignition targets requires radiation-hydrodynamics simulations with accurate models of the fundamental material properties (i.e., equation of state, opacity, and conductivity). Validation of these models is required via experimentation. A feasibility study of using spatially integrated, spectrally resolved, x-ray Thomson scattering measurements to diagnose the temperature, density, and ionization of the compressed DT shell of a cryogenic DT implosion at two-thirds convergence was conducted. Synthetic scattering spectra were generated using 1D implosion simulations from the LILAC code that were post processed with the x-ray scattering model, which is incorporated within SPECT3D. Analysis of two extreme adiabat capsule conditions showed that the plasma conditions for both compressed DT shells could be resolved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Addressing the impact of Lyman opacity in inference of divertor plasma conditions with 2D spectroscopic camera analysis of Balmer emission during detachment in JET L-mode plasmas

The impact of re-absorption of the deuterium Lyman series emission was addressed in inferring divertor plasma conditions from Balmer series emission with 2D spectroscopic camera analysis during detachment in JET L-mode plasmas. The previously presented methodology was amended by modifying the standard photon emission coefficients and ionization and recombination rate coefficients of the ADAS database to consider the re-population of excited states due to Lyman opacity. This resulted in the estimate for the atomic density near the outer strike point to decrease by up to 75% at the onset of detachment at strike point temperatures of T e,osp ≈ 1.0–3.0 eV with respect to the strongly overestimated previously obtained values, whereas the estimated electron temperature and density were unaffected by the opacity correction within the scatter of the data and only a moderate reduction by up to 20% was observed in the estimate for the molecularly induced fraction of the Balmer emission. No noticeable change was seen in the ionization rate, calculated from the estimated outer strike point conditions, due to the decrease in the atomic density estimate compensating for the increased values of the opacity-corrected ADAS rate coefficients for ionization. In detached conditions at T e,osp ≈ 0.5–1.0 eV, 25%–35% lower recombination rates were provided by the opacity-corrected model. The observed effects on the experimental analysis were supported by a corresponding synthetic analysis based on EDGE2D-EIRENE simulations.

Balmer emission↗
NASA NTRS2019

K-line X-ray fluorescence from highly charged iron ions under dense astrophysical plasma conditions

In the present work, we report an investigation of plasma environment effects on the atomic parameters associated with the K-vacancy states in highly charged iron ions within the astrophysical context of accretion disks around black holes. More particularly, the sensitivity of K-line X-ray fluorescence parameters (wavelengths, radiative transition probabilities, and Auger rates) in Fe XVII–Fe XXV ions has been estimated for plasma conditions characterized by an electron temperature ranging from 105 to 107K and an electron density ranging from 1018 to1022 cm−3. In order to do this, relativistic multiconfiguration Dirac-Fock atomic structure calculations have been carried out by considering a time averaged Debye-Hückel potential for both the electron–nucleus and electron–electron interactions.

Jérôme Deprince↗
DOE OSTI2025

Pump with Broadband Probe Experiments for Single-Shot Measurements of Plasma Conditions and Crossed-Beam Energy Transfer

Here, a novel technique for measuring plasma conditions using monochromatic pump-broadband-probe laser interactions has been experimentally demonstrated. Originally proposed in Ludwig et al. [Phys. Plasmas 26, 113108 (2019)], this method utilizes crossed-beam energy transfer between the broadband probe and the pump, mediated by plasma ion acoustic waves. The complete energy transfer spectrum can be captured in a single shot, enabling the inference of plasma parameters such as density, electron and ion temperatures, and flow velocity. Compared to Thomson scattering, this technique offers signal enhancements typically larger than 9 orders of magnitude, significantly reducing the required probe laser intensity and facilitating interactions that are linear and measurements that are nonperturbative of the plasma. Furthermore, it provides a powerful tool for advancing studies of crossed-beam energy transfer under conditions relevant to inertial confinement fusion experiments.

Physics - Plasma physics↗
DOE OSTI2024

Investigating the impact of intermediate-mode perturbations on diagnosing plasma conditions in DT cryogenic implosions via synthetic x-ray Thomson scattering

The pursuit of inertial confinement fusion ignition target designs requires precise experimental validation of the conditions within imploding capsules, in particular the density and temperature of the compressed shell. Previous work has identified x-ray Thomson scattering (XRTS) as a viable diagnostic tool for inferring the in-flight compressed deuterium-tritium shell conditions during capsule implosions (Poole et al 2022 Phys. Plasmas 29 072703). However, this study focused on one-dimensional simulations, which do not account for the growth of hydrodynamic instabilities. In this work, two-dimensional DRACO simulations incorporating intermediate-mode perturbations up to Legendre mode l = 50 were used to generate synthetic XRTS spectra with the SPECT3D code. The analysis employed Markov-Chain Monte Carlo techniques to infer plasma conditions from these spectra. The results demonstrate that the XRTS diagnostic platform can effectively discern the in-flight compressed shell conditions for targets with varying adiabats, even in the presence of intermediate-mode perturbations. This work underscores the potential of XRTS for realistic inertial confinement fusion experiments, providing a robust method for probing the complex dynamics of fusion implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Experimental Investigation of Uranium and Iron Condensation from High-Temperature Plasma Conditions

We used a plasma flow reactor (PFR) to generate synthetic fallout nanoparticles from vapor-phase condensation of two different input concentrations of uranium and iron analytes (U/Fe = 1:1 and 1:2). Synthetic fallout from complex chemical matrices (e.g., mixtures of U and Fe) has not been generated in this setup before and allows for the observation of relative condensation and fractionation of nuclear debris. Experiments were conducted under two different temperature histories with variations in particle flow patterns along the PFR. Transmission electron microscopy (TEM) observation and analysis of the nanoparticles revealed variations in speciation of uranium oxides (UO 2 and α-UO 3 ) depending on the competition between flow mixing and oxygen sequestration by iron. A ternary metal oxide, UFeO 4 , was observed in addition to iron oxides (e.g., FeO and Fe 3 O 4 ), which suggests that fallout models should account for chemical speciation of ternary metal oxides (i.e., UFeO 4 ) and their relative condensation behaviors in addition to those of singular metal oxides (e.g., FeO and UO 2 ). X-ray Energy Dispersive Spectroscopy (EDS) elemental maps showed that some particles had Fe-rich cores surrounded by U-rich regions. This suggests that either condensed U oxides coagulate onto molten Fe oxides or that the increase in iron analyte concentration might drive the system toward a higher degree of supersaturation, leading to earlier formation of iron oxide particles and providing an energetically favored pathway for nucleation of uranium oxides around iron oxide particles.

and nuclear chemistry↗
DOE OSTI2022

Influence of temporal variations in plasma conditions on the electric potential near self-organized dust chains

Self-organization of dust grains into stable filamentary dust structures (or “chains”) largely depends on dynamic interactions between individual charged dust grains and complex electric potential arising from the distribution of charges within a local plasma environment. Recent studies have shown that the positive column of the gas discharge plasma in the Plasmakristall-4 (PK-4) experiment at the International Space Station supports the presence of fast-moving ionization waves, which lead to variations of plasma parameters by up to an order of magnitude from the average background values. The highly variable environment resulting from ionization waves may have interesting implications for the dynamics and self-organization of dust particles, particularly concerning the formation and stability of dust chains. Here, we investigate the electric potential surrounding dust chains in the PK-4 experiment by employing a molecular dynamics model of the dust and ions with boundary conditions supplied by a particle-in-cell with Monte Carlo collision simulation of the ionization waves. The model is used to examine the effects of the plasma conditions within different regions of the ionization wave and compare the resulting dust structure to that obtained by employing the time-averaged plasma conditions. Here, the comparison between simulated dust chains and experimental data from the PK-4 experiment shows that the time-averaged plasma conditions do not accurately reproduce observed results for dust behavior, indicating that more careful treatment of plasma conditions in the presence of ionization waves is required. It is further shown that commonly used analytic forms of the electric potential do not accurately describe the electric potential near charged dust grains under these plasma conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1993

High-time resolution measurements of upstream magnetic field and plasma conditions during flux transfer events at the Earth's dayside magnetopause

We present preliminary results of a study of upstream magnetic field and plasma conditions measured by IRM during flux transfer events observed at the Earth's magnetopause by CCE. This study was designed to determine the importance of various upstream factors in the formation of bipolar magnetic field signatures called flux transfer events (FTEs). Six FTE encounters were examined. In three cases, the two satellites were on similar magnetic field lines. Preliminary investigation showed that fluctuations occurred in the Bz component of the interplanetary magnetic field (IMF) resulting in a southward field preceding the FTE in all three of these cases. In two of these cases, the changes were characterized by a distinct rotation from a strong southward to a strong northward field. There were also accompanying changes in the dynamic and thermal pressure in the solar wind immediately before the FTE was encountered. Examination of the 3D plasma distributions showed that these pulses were due to the addition of energetic upstreaming foreshock particles. There were no consistent changes in either Bz or the plasma pressure at IRM for the three events when the satellites were not connected by the IMF.

Jacob, Jamey D.↗
NASA NTRS1961

Experiments with Plasmas Produced by Potassium-Seeded Cyanogen Oxygen Flames for Study of Radio Transmission at Simulated Reentry Vehicle Plasma Conditions

A method for the chemical production of an ionized gas stream for application to radio transmission studies is described. Involved is the combustion of gaseous cyanogen and oxygen with the addition of vaporized potassium in some cases to further increase the ionization. Experiments are described in which a 3-inch-diameter subsonic free jet at atmospheric pressure is used, and the results are presented. The plasma obtained by using this method is sufficient to simulate plasma conditions expected for reentering hypersonic vehicles. The unseeded plasma stream temperature is indicated to be about 4,200 K, with the degree of ionization indicated to be that expected from thermal equilibrium considerations. Measurements of radio-signal loss due to the unseeded flame plasma are presented for microwaves of 8 to 20 kmc transmitted through the stream and for a dipole transmitting model of 219.5 mc immersed in the stream. Favorable comparison of these results with the simple plane-wave signal-attenuation theory was obtained. In the case of a 9.4-kmc microwave signal of 30-kw peak power, the preliminary indication is that the plasma characteristics were not changed due to this strong signal. Comparison of a simplified concept of radio-signal attenuation due to plasmas is made with some hypersonic reentry vehicle signal-loss data. Other areas of plasma research using this method for the transmission problem are indicated.

Huber, Paul W.↗
DOE OSTI2024

Overview of Large Helical Device experiments of basic plasma physics for solving crucial issues in reaching burning plasma conditions

Recently, experiments on basic plasma physics issues for solving future problems in fusion energy have been performed on a Large Helical Device. There are several problems to be solved in future devices for fusion energy. Emerging issues in burning plasma are: alpha-channeling (ion heating by alpha particles), turbulence and transport in electron dominant heating helium ash exhaust, reduction of the divertor heat load. To solve these problems, understanding the basic plasma physics of (1) wave–particle interaction through (inverse) Landau damping, (2) characteristics of electron-scale (high-k) turbulence, (3) ion mixing and the isotope effect, and (4) turbulence spreading and detachment, is necessary. This overview discusses the experimental studies on these issues and turbulent transport in multi-ion plasma and other issues in the appendix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2003

Modeling Variability of Plasma Conditions in the Io Torus

Telescopic observations an in situ measurements of the Io plasma torus show the density, temperature and composition to vary over time, sometimes up to a factor of 2. While previous models of the physical and chemical processes in the Io plasma torus have reasonably modeled the conditions of the Voyager 1 era, their authors have not addressed the observed variability nor explored the sensitivity of torus conditions to input parameters. In this paper we present a homogeneous torus model parameterized by five variables (transport timescale, neutral source strength, ratio of oxygen sulfur to atoms in the source, fraction of superthermal electrons, temperature of these hot electrons). The model incorporates the most recent data for ionization, recombination, charge exchange and radiative energy losses for the major torus species (S, S(sup +), S(sup ++), S(sup +++), O, O(sup +), O(sup ++). We solve equations of conservation of mass and energy to find equilibrium conditions for a set of input parameters. We compare model plasma conditions with those observed by Voyager 1 Voyager 2, and Cassini. Furthermore, we explore the sensitivity of torus conditions to each parameter. We find that (1) torus conditions are distinctly different for the Voyager 1, Voyager 2 and Cassini eras, (2) unique torus input parameters for any given era are poorly constrained given the wide range of solution space that is consistent with the range of observed torus conditions, (3) ion composition is highly sensitive to the specification of a non-thermal electron distribution, (4) neutral O/S source ratio is highly variable with model values ranging between 1.7 for Cassini to 4.0 for Voyager 1 conditions, (5) transport times range between 23 days for Voyager 2 to 50 days for Voyager 1 and Cassini, (6) neutral source strengths range between 7 to 30 x 10(sup -4) cm (sup -3) s(sup -1) which corresponds to a net production of 0.4 to 1.3 tons/s for a torus volume of 1.4 x 10(sup 31) cm(sup 3), or 38 R(sub j)(sup 3).

Delamere, P. A.↗
DOE OSTI2021

Using neutrons and x rays to measure plasma conditions in a solid sphere of deuterated polyethylene compressed to densities of 35 g/cc at temperatures of 2 keV and pressures of 40 Gbar

This paper describes an experiment that shock compresses the center of a solid deuterated polyethylene sphere, CD 2 , to densities of 35 g/cc and temperatures of 2 keV with corresponding pressure of 40 Gbar. The design employs a strong spherically converging shock launched through a solid ball of material using a Hohlraum radiation drive. As the shock coalesces at the center it produces a hot spot that we characterize by measuring the x-ray self-emission and 2.45 MeV neutrons emitted. Two-dimensional images and time-resolved measurements of the x rays emitted determine the size and time duration of the hot spot, leading to an estimated 2k eV electron temperature. The neutron time of flight spectrometer measures an average ion temperature of 1.06 ± 0.15 keV and neutron yield of 7.0 (±0.5) × 10 9 DD neutrons. Our new distribution function tool enables us to create a forward model of the experimental data based on 1D radiation-hydrodynamic simulations, leading to a better understanding of the plasma conditions that produce the measured neutrons and x rays. Furthermore, our simulations indicate that the x rays are produced in a short-lived hot-dense core over tens of picoseconds, whereas the neutron emission continues for about 200 ps, as the hot core starts to expand, thereby leading to a lower mean temperature of the plasma during neutron production. This finding is in agreement with the experimental data, and we therefore conclude that the forward-modeling is a useful tool for inferring the conditions of the hot spot in a laser-driven implosion during burn.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1991

A comparison of ULF fluctuations in the solar wind, magnetosheath, and dayside magnetosphere. I - Magnetosheath morphology. II - Field and plasma conditions in the magnetosheath

Simultaneous data from ISEE 1 and 2 in the upstream solar wind, from AMPTE IRM in the subsolar magnetosheath, and from AMPTE CCE in the dayside magnetosphere are used to investigate the properties of the magnetosheath responsible for the transmission into the magnetosphere the ULF waves generated in the solar wind upstream of a quasi-parallel bow shock. The data are used to characterize the magnetosheath both during the periods when azimuthally polarized resonant harmonic ULF magnetic pulsations were observed in the dayside outer maagnetosphere, and when they were not. In addition, a detailed analysis is carried out of magnetic field and plasma conditions in the subsolar magnetosheath during these and other periods.

Engebretson, M. J.↗
NASA NTRS1983

On the plasma conditions at the dayside magnetopause of Saturn

The energy densities epsilon(P) of the low energy ions measured by the Low Energy Charged Particle experiment on Voyager 1 and 2 are compared to the magnetic field energy densities derived from the magnetometer instrument during the crossing of the dayside Saturn magnetopause. The ratios of the proton to magnetic field energy densities are greater than about 0.5 during the Voyager 2 crossing when the magnetopause was at about 18 R(s). During the Voyager 1 crossing of the magnetopause at about 23 R(s), the ratios were about 0.1, although they approached one as the spacecraft entered the region near 18 R(s). The observations show that the dayside Saturnian magnetopause can at times have high beta plasma conditions, similar to the situation found at Jupiter.

Lanzerotti, L. J.↗
DOE OSTI2022

Coulomb expansion of a thin dust cloud observed experimentally under afterglow plasma conditions

The Coulomb expansion of a thin cloud of charged dust particles was observed experimentally, in a plasma afterglow. This expansion occurs due to mutual repulsion among positively charged dust particles, after electrons and ions have escaped the chamber volume. In the experiment, a two-dimensional cloud of dust particles was initially levitated in a glow-discharge plasma. The power was then switched off to produce afterglow conditions. The subsequent fall of the dust cloud was slowed by reversing the electric force, to an upward direction, allowing an extended observation. At early time, measurements of the Coulomb expansion in the horizontal direction are found to be accurately modeled by the equation of state for a uniformly charged thin disk. Finally, bouncing from the lower electrode was found to be avoided by lowering the impact velocity <100 mm/s.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1989

Method and apparatus for maintaining thermal control in plasma conditions

An apparatus and method are disclosed for determining the effects of exposure of oxygen plasma on a thin film polymer whose bulk is maintained at a predetermined temperature. The apparatus includes a chamber having a specimen therein. A plasma environment is provided in the chamber. A closure member is provided for sealing the chamber after the specimen is introduced into the chamber. The closure member also serves as a support for the test apparatus which includes a cooling coil. A platform having the test specimen thereon is supported on the cooling coil to be cooled by coolant flowing through the cooling coils. A thermoelectric module is supported on the platform to assist in maintaining a low test temperature for the test samples. The temperature of the sample is monitored by a thermocouple probe which is in contact with the sample. Any change in bulk sample temperature caused by the thermocouple probe is quickly adjusted to maintain the initial bulk temperature by the thermoelectric module.

Whitaker, Ann F.↗