Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “particle impact testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Particle impact tests

Particle impact tests were performed on three types of orbiter surface with a micrometeoroid facility. The test equipment electrostatically accelerated micron sized particles to high velocities simulating micrometeoroid impacts. Test particles were titanium diboride with typical velocities in the range 1 to 2.3 km x sec/1 and equivalent particle diameters in the range 4 to 16 microns. Impact angles to the material surface were 90, 60 and 30 degrees. The particle impact sites were located on the sample surfaces and craters were photographed with a magnification of 400X.

Komatsu, G. K.↗
NASA NTRS1995

Neural Networks Analyze Data In Particle-Impact-Noise Tests

Electronic neural networks and computers put to use in analyzing data acquired in particle-impact-noise-detection (PIND) tests of packaged electronic components. PIND tests detect loose particles in packages that cause failures during subsequent operation of packages in presence of accelerations or other effects - for example, loose electrically conductive particles that bounce into positions in which they cause short circuits. Interpretation of test data more objective and accurate. Preliminary results suggest use of neural networks result in significant improvement in quality and reliability and decrease in cost of PIND testing.

Scaglione, Lois J.↗
NASA NTRS1989

Orbit transfer rocket engine technology program: Oxygen materials compatibility testing

Particle impact and frictional heating tests of metals in high pressure oxygen, are conducted in support of the design of an advanced rocket engine oxygen turbopump. Materials having a wide range of thermodynamic properties including heat of combustion and thermal diffusivity were compared in their resistance to ignition and sustained burning. Copper, nickel and their alloys were found superior to iron based and stainless steel alloys. Some materials became more difficult to ignite as oxygen pressure was increased from 7 to 21 MPa (1000 to 3000 psia).

Schoenman, Leonard↗
NASA NTRS1985

An experimental data base for material selection and design of high-speed, high-pressure, oxygen turbomachinery

New technologies for space-based, reusable, throttleable, cryogenic, orbit transfer propulsion are being evaluated. A variable-thrust (200 to 3000 lbF), 2000 psi chamber pressure, LO2/LH2 engine has been selected to demonstrate the 20-hour, 500-restart life goal, and a specific impulse of 480 lbF-sec/lbM. The advanced design uses warm oxygen to power a fully integrated turbopump that delivers 4500 psi LO2. The selected engine cycle provides the following advantages over conventional expander cycle designs which use H2 to drive the LH2 and LO2 pumps; higher engine operating pressures and performance in a smaller envelope, lower turbine operating temperatures, elimination of interpropellant seals and purges, and an extended throttling range. The design approach and results of testing to characterize materials for use in high-pressure gaseous oxygen are discussed. Test methods include particle impact testing in a sonic-flow, hot GO2 streams and forced, high-speed friction rubbing testing. Materials are exposed to oxygen and nitrogen atmospheres at pressures of 100, 1000, and 3000 psi to identify separately the gas cooling effects from the metal oxidation effects at the rubbing surface. The selection of candidate design materials is based on an analytical parameter defined as the burn factor. Typical materials tested include carbon steel, stainless steel, nickel, copper, and monel alloys.

Schoenman, L.↗
NASA NTRS1992

Specimen Holder For Flammability Tests

Fixture holds sheet specimens for flammability tests. Frame and clamps designed to minimize local overstress on specimen. Heat capacity of fixture low, interfering less with interpretation of results of test by drawing less heat away from specimen. Accepts films, fabrics, foams, and other sheets, rigid or flexible. Specimens thin or thick, or of variable thickness. Bent to accommodate curved rigid specimens. Also used for such other tests as particle-impact tests.

Rucker, Michelle A.↗
NASA NTRS1977

Preparation of calibrated test packages for particle impact noise detection

A standard calibration method for any particle impact noise detection (PIND) test system used to detect loose particles responsible for failures in hybrid circuits was developed along with a procedure for preparing PIND standard test devices. Hybrid packages were seeded with a single gold ball, hermetically sealed, leak tested, and PIND tested. Conclusions are presented.

Source record↗
NASA NTRS1997

SEDS Tether M/OD Damage Analyses

The Small Expendable Deployer System (SEDS) was designed to deploy an endmass at the end of a 20-km-long tether which acts as an upper stage rocket, and the threats from the meteoroid and orbital debris (M/OD) particle environments on SEDS components are important issues for the safety and success of any SEDS mission. However, the possibility of severing the tether due to M/OD particle impacts is an even more serious concern, since the SEDS tether has a relatively large exposed area to the M/OD environments although its diameter is quite small. The threats from the M/OD environments became a very important issue for the third SEDS mission, since the project office proposed using the shuttle orbiter as a launch platform instead of the second stage of a Delta II expendable rocket, which was used for the first two SEDS missions. A series of hyper-velocity impact tests were performed at the Johnson Space Center and Arnold Engineering Development Center to help determine the critical particle sizes required to sever the tether. The computer hydrodynamic code or hydrocode called CTH, developed by the Sandia National Laboratories, was also used to simulate the damage on the SEDS tether caused by both the orbital debris and test particle impacts. The CTH hydrocode simulation results provided the much needed information to help determine the critical particle sizes required to sever the tether. The M/OD particle sizes required to sever the tether were estimated to be less than 0.1 cm in diameter from these studies, and these size particles are more abundant in low-Earth orbit than larger size particles. Finally, the authors performed the M/OD damage analyses for the three SEDS missions; i.e., SEDS-1, -2, and -3 missions, by using the information obtained from the hypervelocity impact test and hydrocode simulations results.

Hayashida, K. B.↗
NASA NTRS1991

Test methods for determining the suitability of metal alloys for use in oxygen-enriched environments

Materials are more flammable in oxygen rich environments than in air. When the structural elements of a system containing oxygen ignite and burn, the results are often catastrophic, causing loss of equipment and perhaps even human lives. Therefore, selection of the proper metallic and non-metallic materials for use in oxygen systems is extremely important. While test methods for the selection of non-metallic materials have been available for years, test methods for the selection of alloys have not been available until recently. Presented here are several test methods that were developed recently at NASA's White Sands Test Facility (WSTF) to study the ignition and combustion of alloys, including the supersonic and subsonic speed particle impact tests, the frictional heating and coefficient of friction tests, and the promoted combustion test. These test methods are available for commercial use.

Stoltzfus, Joel M.↗
NASA NTRS1984

Selection of burn-resistant materials for oxygen-driven turbopumps

NASA goals for reusable space-based, high-performance orbit transfer vehicle propulsion systems have resulted in a need for oxygen/hydrogen engines which include lightweight, highly reliable, liquid oxygen pumps. The selection of ignition- and burn-resistant materials is a major factor in the design of a compact 75,000-rpm turbopump which can deliver 6 lbM/sec of liquid oxygen at 5,000 psia. The potential operational hazards of rubbing friction and impact of foreign particles at high velocity were investigated experimentally for a wide range of candidate materials, i.e., nickel, copper, monel, 316 Stainless Steel, Hastelloy-X, Invar-36, and silicon carbide. Test parameters included oxygen pressure and temperature up to 5,000 psia and 800 F, respectively. The effect of increasing the O2 pressure from 1000 to 5000 psi is discussed. The applicability of the candidate materials to oxygen pump design was ranked by comparing the experimental results among themselves and with an analytically determined parameter, i.e., the burn factor. Nickel and copper demonstrated superior resistance to ignition and burn in the friction rubbing and particle impact tests relative to monel, stainless steel, and nickel-iron base superalloys.

Schoenman, L.↗
NASA NTRS1991

Impact design methods for ceramic components in gas turbine engines

Methods currently under development to design ceramic turbine components with improved impact resistance are presented. Two different modes of impact damage are identified and characterized, i.e., structural damage and local damage. The entire computation is incorporated into the EPIC computer code. Model capability is demonstrated by simulating instrumented plate impact and particle impact tests.

Song, J.↗
NASA NTRS1975

Contamination Control in Hybrid Microelectronic Modules. Part 1: Identification of Critical Process and Contaminants

Various hybrid processing steps, handling procedures, and materials are examined in an attempt to identify sources of contamination and to propose methods for the control of these contaminants. It is found that package sealing, assembly, and rework are especially susceptible to contamination. Moisture and loose particles are identified as the worst contaminants. The points at which contaminants are most likely to enter the hybrid package are also identified, and both general and specific methods for their detection and control are developed. In general, the most effective controls for contaminants are: clean working areas, visual inspection at each step of the process, and effective cleaning at critical process steps. Specific methods suggested include the detection of loose particles by a precap visual inspection, by preseal and post-seal electrical testing, and by a particle impact noise test. Moisture is best controlled by sealing all packages in a clean, dry, inert atmosphere after a thorough bake-out of all parts.

Himmel, R. P.↗
NASA NTRS1992

The effectiveness of multi-layer insulation as meteoroid and orbital debris shielding

This paper presents the results of a study of the penetration resistance of Type I Multi-Layer Insulation (MLI) to meteoroid and orbital debris particles. Hypervelocity impact tests on MLI were performed and the collected data was compared to data and empirical equations developed for aluminum. The study results indicate that MLI can be an effective shield from meteoroids and orbital debris for short duration missions and for non-critical elements. However, long missions which require high levels of protection cannot rely on MLI without a thorough investigation of the overall system reliability.

Robinson, J. H.↗
NASA NTRS1993

TSS tether cable meteoroid/orbital debris damage analysis

This report summarizes the damage analyses performed on the tether cable used for the tethered satellite system (TSS), for the damage that could be caused by meteoroid or orbital debris impacts. The TSS consists of a tethered satellite deployer and a tethered satellite. The analytical studies were performed at Marshall Space Flight Center (MSFC) with the results from the following tests: (1) hypervelocity impact tests to determine the 'critical' meteoroid particle diameter, i.e., the maximum size of a meteoroid particle which can impact the tether cable without causing 'failure'; (2) electrical resistance tests on the damaged and undamaged tether cable to determine if degradation of current flow occurred through the damaged tether cables; and (3) tensile load tests to verify the load carrying capability of the damaged tether cables. Finally, the HULL hydrodynamic computer code was used to simulate the hypervelocity impact of the tether cable by particles at velocities higher than can be tested, to determine the extent of the expected tether damage.

Hayashida, K. B.↗
NASA NTRS1978

Some aspects of contamination detection, analyses, and control in microcircuits for the NASA Space Shuttle program

The Space Shuttle system is currently one of the National Aeronautics and Space Administration's (NASA) most important and complex programs. A significant number of hybrid microcircuits are being developed and used on the Space Shuttle. Since the Shuttle is a manned vehicle, reliability of the hybrids is flight critical. Loose particle contamination is one of the major causes of failure and reduced operating life for microcircuits. Process controls, surface coatings, and the particle impact noise detection (PIND) test were assessed for control of particle contamination, and the decision was made by NASA to require PIND test for all hybrid circuits. Selected hybrids from the production line of one vendor that had failed the PIND test were analyzed. Results of this program are presented.

Caruso, S. V.↗
NASA NTRS1979

Shock during PIND test frees particles

Recent study on Particle-Impact Noise-Detection (PIND) shows impact at 1,500 to 4,000 G normally imparted to hybrid microcircuits during testing knocks loose stray trapped particle that can be subsequentially removed. Process may be 80 to 90 percent effective in removal of particles depending on type of test utilized.

Caruso, S. V.↗
NASA NTRS1988

Ignition of steel alloys by impact of low-velocity iron/inert particles in gaseous oxygen

The ignition of carbon steel and 316 and 304 stainless steels caused by the impact of low-velocity particles (a standard mixture consisting of 2 g of iron and 3 g of inert materials) in gaseous oxygen was investigated using NASA/White Sands Test Facility for the ignition test, and a subsonic particle impact chamber to accelerate the particles that were injected into flowing oxygen upstream of the target specimen. It was found that the oxygen velocities required to ignite the three alloys were the same as that required to ignite the particle mixture. Ignition occurred at oxygen velocities greater than 45 m/sec at 20 to 24 MPa and was found to be independent of pressure between 2 and 30 MPa. Comparison of the present results and the past results from Wegener (1964) with the Compressed Gas Association (CGA) oxygen velocity limits for safe operations indicates that the CGA limits may be excessively conservative at high pressures and too liberal at low pressures.

Benz, Frank J.↗