Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “motorcycles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The Value of Motorcycle Electrification in Mexico City

Local and city governments worldwide are looking to adopt emerging technologies and mobility approaches, such as electric vehicles, as they pursue their environmental and economic goals. Commercially available electric vehicles include buses, automobiles, motorcycles, and other two-wheelers. Electrifying transportation is critical to achieve urban sustainability, but it also raises challenges for private and public actors. Jurisdictions across countries are seeking to answer big questions, including how the transportation sector can be electrified, what impacts are priorities, and how such impacts can be obtained.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Motorcycle Safety Committee [Slides]

This is a presentation to be sent to various DOE sites as a reference for LANL's Motorcycle Safety Committee and includes how to start and sustain a safety committee and organize events. Examples from LANL's program are included. Contacts from Los Alamos National Lab, Lawrence Livermore National Lab, and Idaho National Lab are provided.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
NASA NTRS1973

An experimental study of the motorcycle roll stabilization task

The work of Sharp represents the most complete theoretical analysis of the uncontrolled motorcycle presently available, and serves as a theoretical basis for the study described. Sharp's analysis included roll, yaw, lateral translation, and steering degrees of freedom, and the resulting equations are linear with constant coefficients. Tire aligning moments due to tire sideslip were added to Sharp's equations. Experimental results are presented, and related to the theoretical studies of Sharp and Weir.

Eaton, D. J.↗
NASA NTRS1993

Motorcycle Parts

An article in NASA Tech Briefs describing a vacuum bagging process for forming composite parts helped a small Oklahoma Company to improve its manufacturing process. President of Performance Extremes, Larry Ortega, and his partners make motorcycle parts from carbon/epoxy to reduce weight. Using vacuum bags, parts have a better surface and fewer voids inside. When heat used in the vacuum bag process caused deformation upon cooling, a solution found in another tech brief solved the problem. A metal plate inside the vacuum bag made for more even heat transfer. A third article described a simple procedure for repairing loose connector pins, which the company has also utilized.

Source record↗
NASA NTRS1976

The subjective evaluation of noise from light aircraft

A study was conducted in which subjects evaluated the sounds of a light aircraft and a motorcycle. Particular emphasis was placed on examining the duration of the sounds. Thirty subjects gave annoyance ratings to a total of 50 sounds, with peak levels between 65 and 85dB(A). It was found that aircraft and motorcycles have differing optimum duration corrections. The conventional duration correction used in the calculation of EPNL is far from being the optimum for light aircraft.

Shepherd, K. P.↗
NASA NTRS1986

Rotary Speed Sensor for Antilocking Brakes

Sensor based on fluidic principles produces negative pressure approximately proportional to rotational speed. Sensor developed as part of antilocking brake system for motorcycles. Uses inlet pressure rather than outlet pressure as braking-control signal, eliminating pressure pulsations caused by pump vanes and ensuring low-noise signal. Sensor is centrifugal air pump turned by one of motorcycle wheels. Air enters pump through orifice plates, and suction taken off through port in pump inlet plenum.

Berdahl, C. M.↗
DOE OSTI2020

The Old Post

Motorcycle Safety Committee Newsletter encouraging safe riding habits and raising awareness for motorcyclists at LANL, LLNL and INL.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2021

Science Personality and STEM Ambassador

Dr. Amy Elliott has had unique opportunities to serve as a STEM role model through her various media production projects. Her debut on screen was as a competitor on an engineering reality show competition called “The Big Brain Theory,” aired by The Discovery Channel. Following this competition, Dr. Elliott served as an on-camera host for RoboNation’s water-based, annual collegiate competitions and for The Science Channel’s viral video show, “Outrageous Acts of Science.” Dr. Elliott also serves as volunteer pit-crew for Green Envy Racing, a woman-lead race team that seeks to set and speed records with electric motorcycles. Because of Dr. Elliott’s public exposure, she was selected as an IF/THEN Ambassador by the American Associate for the Advancement of Science (AAAS), a program that seeks to highlight women as STEM role models. Dr. Elliott’s work in 3D printing is frequently a source of inspiration for her.

Elliott, Amy↗
DOE OSTI2021

The 3D printing and modeling of functionally graded Kelvin foams for controlling crushing performance

Mechanical impact protection is an important consideration in many applications, ranging from product transportation to sports. Cellular materials are typically used due to their desirable energy absorption properties and light weight. However, their large deformation and rate dependent responses (especially of polymer foams) are challenging to consider in design. Additionally, the use of foams with uniform properties, such as uniform density and uniform stiffness, often restricts the designed foams to only be suitable for a narrow range of mechanical impact conditions whereas real applications commonly face unpredictable situations. 3D printing offers fabrication flexibility and thus opens the door to create foams with tailored properties. In this work, we investigate the feasibility of using 3D printing for functionally graded foams (FGFs) that are optimal over a broad range of mechanical environments. The foams are fabricated by the recently developed grayscale digital light processing (g-DLP) method which can print parts with locally designed properties. These foams are tested under drop test conditions and with slower displacement control. We also model the large deformation behavior of FGFs using finite element analysis in which we account for the different viscoelastic behaviors of the distinct grayscale regions. We then use the model to examine the impact mitigation capabilities of FGFs in different loading scenarios. Finally, we show how FGFs can be used to satisfy real-world design goals using the case study of a motorcycle helmet. In contrast to prior work, we investigate continuous, functionally graded foams of a single density that differ in their viscoelastic responses. This work provides further insight into the benefits of viscoelastic properties and modulus graded foams and presents a manufacturing approach that can be used to produce the next generation of flexible lattice foams as mechanical absorbers.

3D printing↗
DOE OSTI2024

Hestia SW-IFL Onroad Fossil Fuel Carbon Dioxide (FFCO2) product: Road segment-level annual FFCO2 emissions across Arizona (2017-2022), version 1.1

The SW-IFL onroad fossil fuel carbon dioxide (FFCO2) emissions data product represents CO2 emissions from the combustion of fossil fuels by motor vehicles (e.g., passenger cars, trucks, buses, motorcycles) traveling on designated roadways. The emissions are represented geographically on each road segment within the state of Arizona spanning the 2017 to 2022 time period. This data product was developed as part of the Southwest Urban Corridor Integrated Field Laboratory (SW-IFL) project, which aims to provide new knowledge and tools that address urban environmental issues by integrating high-resolution observations, modeling, and civic engagement. The emissions data are provided in CSV (input data, ONR_FFCO2_AZ_county.csv) and GeoPackage form (output polyline objects - about 786,000 road segments, XXXX_AZ_v1.1.gpkg) designated by road class (interstates, arterials, collectors, local). The metadata file (Metadata_SW-IFL_Onroad_annualFFCO2_v1.1.docx) provides details about attributes and data formats. The GeoPackage emissions data are provided separately for local roads and nonlocal roads (interstates, arterials, collectors). The method file (Methods_SW-IFL_Onroad_annualFFCO2_v1.1.docx) describes the data processing flow and data sources. Update on 2024-04-17: Updates were made to both the input emission data file (.csv) and output segment-level emission file (.gpkg). There was an update in county-level emission input data (ONR_FFCO2_AZ_county.csv) and the entire road segments were reprocessed to reflect this update.Update on 2024-04-29: Update was made to one output segment-level emission file (Nonlocal_AZ_v1.0.gpkg). There was an error in the AADT values and the data were reprocessed to reflect this update.Update on 2024-10-22: Temporal coverage was extended to include 2022. VMT values were recalculated using new AADT data and the entire road segments were reprocessed to reflect these updates.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Embodied Energy in Pyrolysis and Solvolysis Approaches to Recycling for Carbon Fiber-Epoxy Reinforced Composite Waste Streams

Carbon fiber composites are increasingly used in aerospace, motorcycles, sporting, and high-performance vehicles, and their end of life recycling is of growing interest. This study deals with the life cycle assessment (LCA) of carbon fiber reinforced plastics (CFRP) waste streams. The embodied energy (EE) of recycling CFRP via two viable methods—i.e., pyrolysis and solvolysis—is studied. Both pyrolysis and solvolysis were studied for EE with different variants. Alongside fiber recovery from CFRP, the pyrolysis process calculations consider energy recovery from syngas and oil produced within the system. For pyrolysis, electric furnace and natural gas were primarily considered. For solvolysis, different solvent scenarios were considered, including (a) deionized water, (b) water and potassium hydroxide, (c) acetone and water, and (d) water with acetic acid and potassium hydroxide. Energy reduction from one generation to the next has also been highlighted. The EE for recycling CFRP is quantified and discussed for these scenarios in this paper.

composites↗
DOE OSTI2022

An Investigation into the Effects of Swirl on the Performance and Emissions of an Opposed-Piston Two-Stroke Engine using Large Eddy Simulations

Opposed-piston two-stroke (OP-2S) engines have the potential to achieve higher thermal efficiency than a conventional four-stroke diesel engine. However, the uniflow scavenging process is difficult to control over a wider range of speed and loads due to its sensitivity to pressure dynamics, port timings, and port design. Specifically, the angle of the intake ports can be used to generate swirl which has implications for open and closed cycle effects. This study proposes an analysis of the effects of port angle on the in-cylinder flow distribution and combustion performance of an OP-2S using computational fluid dynamics engine. Large Eddy Simulation (LES) was used to model turbulence given its ability to predict in-cylinder mixing and cyclic variability. A three-cylinder model was validated to experimental data collected by Achates Power and the grid was verified using an LES quality approach from the literature. The model was used to simulate port angles from 12 to 29 degrees at constant pressure and temperature boundary conditions. Results indicated that the higher bulk swirl ratio generated by larger port angles tends to trap more internal residuals. This effect on the scavenging performance, combined with the larger trapped swirl ratio, also has a significant impact on the combustion performance in a two-stroke engine. It was concluded that there exists a tradeoff of efficiency and emissions that must be considered when increasing the port angle in a uniflow two-stroke engine. 1. Introduction Two-stroke engines were developed in the 1800s and are commonly used in practice today for lightweight power applications such as motorcycles or handheld power tools, as well as large-bore low speed engines for stationary power and marine applications. Two-stroke engines provide the distinct advantage of higher torque/power output but present challenges due to its coupled intake and exhaust process. Four-stroke engines have the benefit of using two full piston strokes to induct intake charge and to expel exhaust gases. Controlling the trapped charge composition in a twostroke engine via a scavenging process is crucial for reliable and efficient engine operation.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1976

Applications of the Ultrasonic Serial Number Restoration Technique to Guns and Typical Stolen Articles

An ultrasonic cavitation method for restoring obliterated serial numbers has been further explored by application to articles involved in police cases. The method was applied successfully to gun parts. In one case portions of numbers were restored after prior failure by other laboratories using chemical etching techniques. The ultrasonic method was not successful on a heavily obliterated and restamped automobile engine block, but it was partially successful on a motorcycle gear-case housing. Additional studies were made on the effect of a larger diameter ultrasonic probe, and on the method's ability to restore numbers obliterated by peening.

Young, S. G.↗
NASA NTRS1982

Small Fixture Strains Composites for Environmental Tests

Fixture for long-term strain tests of composites is based on inexpensive tool for repairing motorcycle chains. (In normal use tool forces rivet out of chain element.) As modified for composite testing, tool has precision screw and shim. Qualification tests for graphite/epoxy composites are made less expensive by simple test fixture. Used in quantity, fixtures apply precisely similar loads to many samples.

Tervet, F. W.↗
NASA NTRS1982

Ranging/tracking system for proximity operations

The hardware development and testing phase of a hand held radar for the ranging and tracking for Shuttle proximity operations are considered. The radar is to measure range to a 3 sigma accuracy of 1 m (3.28 ft) to a maximum range of 1850 m (6000 ft) and velocity to a 3 sigma accuracy of 0.03 m/s (0.1 ft/s). Size and weight are similar to hand held radars, frequently seen in use by motorcycle police officers. Meeting these goals for a target in free space was very difficult to obtain in the testing program; however, at a range of approximately 700 m, the 3 sigma range error was found to be 0.96 m. It is felt that much of this error is due to clutter in the test environment. As an example of the velocity accuracy, at a range of 450 m, a 3 sigma velocity error of 0.02 m/s was measured. The principles of the radar and recommended changes to its design are given. Analyses performed in support of the design process, the actual circuit diagrams, and the software listing are included.

Nilsen, P.↗
NASA NTRS1993

A four-axis hand controller for helicopter flight control

A proof-of-concept hand controller for controlling lateral and longitudinal cyclic pitch, collective pitch and tail rotor thrust was developed. The purpose of the work was to address problems of operator fatigue, poor proprioceptive feedback and cross-coupling of axes associated with many four-axis controller designs. The present design is an attempt to reduce cross-coupling to a level that can be controlled with breakout force, rather than to eliminate it entirely. The cascaded design placed lateral and longitudinal cyclic in their normal configuration. Tail rotor thrust was placed atop the cyclic controller. A left/right twisting motion with the wrist made the control input. The axis of rotation was canted outboard (clockwise) to minimize cross-coupling with the cyclic pitch axis. The collective control was a twist grip, like a motorcycle throttle. Measurement of the amount of cross-coupling involved in pure, single-axis inputs showed cross coupling under 10 percent of full deflection for all axes. This small amount of cross-coupling could be further reduced with better damping and force gradient control. Fatigue was not found to be a problem, and proprioceptive feedback was adequate for all flight tasks executed.

Demaio, Joe↗
DOE OSTI2021

Global Ethanol-Blended-Fuel Vehicle Compatibility Study

The objective of this study is to understand the impact of ethanol-blended fuel at various blending levels (10%, 15%, and 20% vol.) on "in-operation" vehicles built to differing emissions and manufacturing standards around the world. The study focuses on vehicles used in Canada, China, India, Indonesia, Japan, South Korea, and Mexico. Historical experience in the United States and Brazil informs the analysis. The primary study question is: Are vehicles in targeted countries physically and operationally compatible with ethanol blended fuel? For a fuel to be compatible with a vehicle, the fuel must perform its function as part of the integrated fuel-vehicle system, meaning: the car should start easily and drive normally, the fuel should not cause catastrophic fuel system leaks, the fuel should not cause corrosion or degradation of any engine or fuel system components (including emissions control components). The history of E10 use in the United States, beginning in 1978, was evaluated and shows no reliability or operability issues for cars dating back to pre-emissions-control times -- and likely included many cars manufactured in the 1960s. This strongly supports the contention that fuel chemistry and property differences between E0 and E10 are so small that any car made to international standards in the last 50 years will have a very high probability of being fully compatible with E10. This conclusion is supported by the experience in Brazil in the 1970s, where E10 was also introduced, and ethanol blending for conventional cars rapidly ramped up to even higher blend levels. A limited number of fuel system and component manufacturers supply the global market, including Bosch, Continental, Denso, Delphi, and Visteon. To reduce complexity, ethanol-compatible materials began to be integrated in fuel system designs globally. Fuel systems evolved over the following decades to incorporate ethanol-compatible materials with core subsystem families, such as in-tank fuel pumps used across several global vehicle original equipment manufacturers (OEMs). A similarly compelling case can be made that all cars at the Tier 1 (or equivalent) emissions-control technology level or higher are fully compatible with E15 blends, based on the data evaluated by the U.S. Environmental Protection Agency (EPA) and Ricardo in 2010. For cars at this technology level, the minor differences in fuel chemistry and properties between E10 and E15 are not significant. For E20, studies are not as extensive but are still highly significant. A long-term durability study conducted on mileage accumulation dynamometers presents convincing evidence that Tier 2 technology level cars have materials of construction and engine control authority for compatibility with E20, although this conclusion is not as strong as those drawn for E10 and E15, which are also partly based on real-world experience.

09 BIOMASS FUELS↗