Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “minimodules”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-voltage monocrystalline Si photovoltaic minimodules based on poly -Si/SiO x passivating contacts for high-power laser power conversion

By using photovoltaic cells under high-intensity laser illumination, much higher photoconversion efficiencies are obtained than under the solar spectrum. Here we demonstrate a monocrystalline Si based minimodule to convert laser light into electricity using edge-illuminated Si "minicells" based on polysilicon on silicon oxide passivating contacts. Ten fully metallized devices were stacked in series and illuminated from the edge, creating a high-voltage, low-current minimodule that mitigates resistive and Auger-Meitner losses. The minimodule shows a high open-circuit voltage of >5 V when tested under 1-Sun illumination and >7 V at higher illumination intensities when tested with a flash simulator. The fill factor in these minimodules is limited by shunting at low illuminations but reaches a maximum of ~78% for higher illumination intensities >40 Suns (current density >1200 mA/cm 2 ), indicating that the minimodules are not limited by series resistance up to 40 Suns. Under 1000 nm monochromatic light, we measure efficiencies >40% at > 40 Suns equivalent illumination, showing the potential of passivated contact Si cells for laser power conversion.

14 SOLAR ENERGY↗
DOE OSTI2026

Extended Accelerated Stress Testing of Lamination-Free Edge-Sealed Photovoltaic Minimodules

Lamination-free minimodules are constructed with silicon solar cells between glass sheets and an edge seal of polyisobutylene and silicone. These samples are stressed using a repeated sequential testing sequence including ultraviolet-containing simulated solar spectrum light exposure at elevated temperature, damp heat, humidity freeze, and thermal cycling adapted from the International Electrotechnical Commission (IEC) TS 63209-2:2022. The minimodule performance throughout the stressing is characterized by flash testing and electroluminescence imaging. Results are compared to conventional laminated minimodules using the same type of solar cells. The lamination-free minimodules experience up to 8% power loss compared to roughly 3% for the laminated versions. However, those losses, dominated by current and fill factor, are caused by glass soiling and busbar ribbon separation on the cells. When glass is replaced and the stressed cells are contacted with probes bypassing the delaminated ribbons, the initial performance is recovered, and overall losses of the lamination-free samples become negligible.

14 SOLAR ENERGY↗
DOE OSTI2021

Mechanistic Insights to Degradation of PERC Minimodules with Differentiated Packaging Materials & Module Architectures

In this paper, we study the degradation behavior of glass-backsheet (GB) and double glass (DG) multicrystalline sil- icon monofacial PERC minimodules, fabricated using polyolefin elastomer (POE) and ethylene vinyl acetate (EVA) encapsulants, undergoing exposures of modified damp-heat (80 °C / 85% RH), with and without full spectrum light. The completed exposure time, at this time, is 1512 hours with each step of 504 hours. Step- wise measurements are conducted throughout exposures including current-voltage (I-V ) curves, Suns-V oc , electroluminescence (EL) images, and four-point proof loading with EL for tracking changes in mechanical properties in encapsulants by cell fracture probability. The results show that GB minimodules of both encapsulants, compared to DG minimodules, experience more changes in features of I-V and Suns-V oc measurements. There is no development of PV cell cracking during proof loading as seen from EL images and the load versus load line displacement plots currently.

14 SOLAR ENERGY↗
NASA NTRS2001

Brain-Pituitary Axis Development In The CEBAS Minimodule

The CEBAS minimodule system is a man-made aquatic ecological system that incorporates animals, plants, snails, and microorganisms. It has been proposed that CEBAS will lead to a multigenerational experimental facility for utilization in a space station as well as for the development of an aquatic CELSS to produce animal and plant biomass for human nutrition. In this context, research on the reproductive biology of the organisms within the system should receive the highest priority. 1bus, the goals of our proposal were to provide information on space-flight-induced changes in the brain-pituitary axis and in the organs that receive information from the environment in the vertebrate selected for the CEBAS Minimodule program, the freshwater teleost Xiphophorus helleri (the swordtail). We studied the development of the brain- pituitary axis in neonates, immature and mature swordtails using histology, cytology, immunohistochemistry, morphometry, and in situ histochemistry to evaluate the synthesis, storage, and release of neurotransmitters, neuroregulatory peptides, neurohormones, and pituitary hormones as well as the structure of the organs and cells that produce, store, or are the target organs for these substances. We flew experiments in the CEBAS-minimodule on two shuttle missions, STS-89 and STS-90. In both flights four gravid females and about 200 juvenile (7 days old) swordtails (Xiphophorus helleri) constituted the aquatic vertebrates to be studied, in addition to the plants and snails that were studied by other team members. In a sample sharing agreement developed with Dr. Volker Bluem, organizer of the CEBAS research program, we received a small number of the juveniles and shared the brains of two adult females.

Schreibman, Martin P.↗
DOE OSTI2024

Iodide manipulation using zinc additives for efficient perovskite solar minimodules

Abstract Interstitial iodides are the most critical type of defects in perovskite solar cells that limits efficiency and stability. They can be generated during solution, film, and device processing, further accelerating degradation. Herein, we find that introducing a small amount of a zinc salt- zinc trifluoromethane sulfonate (Zn(OOSCF 3 ) 2 ) in the perovskite solution can control the iodide defects in resultant perovskites ink and films. CF 3 SOO ̶ vigorously suppresses molecular iodine formation in the perovskites by reducing it to iodide. At the same time, zinc cations can precipitate excess iodide by forming a Zn-Amine complex so that the iodide interstitials in the resultant perovskite films can be suppressed. The perovskite films using these additives show improved photoluminescence quantum efficiency and reduce deep trap density, despite zinc cations reducing the perovskite grain size and iodide interstitials. The zinc additives facilitate the formation of more uniform perovskite films on large-area substrates (78-108 cm 2 ) in the blade-coating process. Fabricated minimodules show power conversion efficiencies of 19.60% and 19.21% with aperture areas of 84 and 108 cm 2 , respectively, as certified by National Renewable Energy Laboratory (NREL), the highest efficiency certified for minimodules of these sizes.

14 SOLAR ENERGY↗
DOE OSTI2024

Multifunctional entinostat enhances the mechanical robustness and efficiency of flexible perovskite solar cells and minimodules

Flexible perovskite solar cells (F-PSCs), prized for their nature of soft and high power-weight compatibility, have attracted intensive attention. However, inferior buried perovskite-substrate interfaces due to low interfacial adhesion between perovskites and substrates and large deformation of flexible substrates have greatly limited the performance of F-PSCs. Here, we add organic molecule Entinostat (ET) into hole extraction material Poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) to enhance the adhesion at the perovskite/substrate interface using the interactions of ET with perovskites, PTAA and indium tin oxide (ITO) through its multiple function groups. Meanwhile, ET added into perovskites reduces the voids at the bottom perovskite film, due to its capability to tune the crystallization of perovskites by forming adduct with lead. Consequently, the inverted small area F-PSCs achieved an efficiency of 23.4%. The flexible perovskite minimodule with an area of 9 cm 2 achieved an aperture efficiency of ~19.0% certified by National Renewable Energy Laboratory. Furthermore, the optimized unencapsulated flexible minimodule retained 84% of the initial efficiency after 5000 bending cycles and retained 90% of the initial PCE (T90) after light soaking for >750 hours.

14 SOLAR ENERGY↗
DOE OSTI2023

Lead-chelating hole-transport layers for efficient and stable perovskite minimodules

The defective bottom interfaces of perovskites and hole-transport layers (HTLs) limit the performance of p-i-n structure perovskite solar cells. We report that the addition of lead chelation molecules into HTLs can strongly interact with lead(II) ion (Pb 2+ ), resulting in a reduced amorphous region in perovskites near HTLs and a passivated perovskite bottom surface. Here, the minimodule with an aperture area of 26.9 square centimeters has a power conversion efficiency (PCE) of 21.8% (stabilized at 21.1%) that is certified by the National Renewable Energy Laboratory (NREL), which corresponds to a minimal small-cell efficiency of 24.6% (stabilized 24.1%) throughout the module area. Small-area cells and large-area minimodules with lead chelation molecules in HTLs had a light soaking stability of 3010 and 2130 hours, respectively, at an efficiency loss of 10% from the initial value under 1-sun illumination and open-circuit voltage conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Elongated Fullerene Unlocks Oxygen-Resistant Perovskite Solar Minimodules

State-of-the-art encapsulation cannot prevent the permeation of oxygen into perovskite solar cells (PSCs). Here, we report the finding that p-i-n structured PSCs degrade quickly under oxygen exposure. Oxidation of C60, rather than perovskites, dominates the degradation. Chemical absorption of oxygen by C60 is identified, which impairs its electron transport property. We modify the electron transport layers to address the instability under oxygen exposure. The elongated fullerene C70 is found to react with oxygen orders of magnitude slower than C60. In combination with a compact SnO2 buffer fabricated by atomic layer deposition, which can slow down the oxygen diffusion, the resulting unencapsulated PSCs with C70 retained 90% of their initial efficiency after 1-sun illumination in pure oxygen for 1,200 h at 70 degrees C, improving stability by hundreds of times. Testing of unencapsulated perovskite minimodules of different perovskite compositions with C70 gives extrapolated lifetimes of 17-41 years at 50 degrees C.

14 SOLAR ENERGY↗
DOE OSTI2026

Performance Modeling of Tandem Photovoltaics: A Yearlong Outdoor Degradation Analysis of a Ga⁢As//Si Minimodule

We present a performance modeling and degradation analysis framework for tandem photovoltaic modules, building upon established procedures for crystalline silicon devices and adapting them to account for the spectral sensitivity of multijunction technologies. The methodology employs filter criteria to select outdoor measurements close to standard test conditions (STC) under stable spectral and ambient conditions, followed by normalization of power production data with corrections for temperature, irradiance, and precipitable water vapor. We demonstrate this framework using a mechanically stacked four-terminal gallium arsenide (Ga⁢As) // silicon (Si) tandem solar minimodule deployed outdoors from October 2019 to January 2021 in Golden, Colorado, USA. We determined degradation rates of −4.1 ±0.2%/year for the Ga⁢As subcell and −2.5 ±0.9%/year for the Si subcell, with analysis of individual performance metrics indicating that packaging degradation, particularly delamination, was the dominant failure mode. Simulations using PVcircuit, an open-source equivalent-circuit solver, confirmed these findings. The presented methodology provides a reproducible foundation for performance modeling and degradation analysis of emerging tandem technologies.

14 SOLAR ENERGY↗
DOE OSTI2023

Statistical analysis and degradation pathway modeling of photovoltaic minimodules with varied packaging strategies

Degradation pathway models constructed using network structural equation modeling (netSEM) are used to study degradation modes and pathways active in photovoltaic (PV) system variants in exposure conditions of high humidity and temperature. This data-driven modeling technique enables the exploration of simultaneous pairwise and multiple regression relationships between variables in which several degradation modes are active in specific variants and exposure conditions. Durable and degrading variants are identified from the netSEM degradation mechanisms and pathways, along with potential ways to mitigate these pathways. A combination of domain knowledge and netSEM modeling shows that corrosion is the primary cause of the power loss in these glass/backsheet PV minimodules. We show successful implementation of netSEM to elucidate the relationships between variables in PV systems and predict a specific service lifetime. The results from pairwise relationships and multiple regression show consistency. This work presents a greater opportunity to be expanded to other materials systems.

electrical measurements↗
DOE OSTI2022

Evaluation of PV Module Packaging Strategies of Monofacial and Bifacial PERC Using Degradation Pathway Network Modeling

As the PV industry is rapidly expanding, it is important to thoroughly investigate the long-term impact of packaging strategies on the performance of PV modules. In this study, the variants in sets differ on the basis of manufacturer (A/B), encapsulant (EVA/POE), rear encapsulant (UV-cutoff/opaque/transparent), module architecture (GB/DG) and cell type (monofacial/bifacial). The minimodules were exposed for 2520 hours in modified damp heat, with or without full spectrum light. Every 504 hours, stepwise electrical characterization techniques were employed to track changes in minimodules. Degradation pathway modeling using network structural equation modeling was employed to study pairwise relationships between variables and service lifetime prediction in minimodules. Through this study, differences in quality control are identified in minimodules made by different manufacturers. Minimodules with UV-cutoff rear encapsulant show relatively better stability, whereas the ones with opaque rear encapsulant show greater power loss. In addition, GB having UV-cutoff rear encapsulation and GB with POE having opaque rear encapsulation were identified to be stable as they lack a best model fit. Here, the primary power loss mechanism in degrading variants is interconnect corrosion.

14 SOLAR ENERGY↗
DOE OSTI2026

Innovative Interfacial Engineering for Simultaneous Enhancement in Efficiency, Stability, and Reliability in Perovskite Devices

The overarching objective of this project was to increase significantly the mechanical adhesion toughness of the key interfaces in PSCs, thereby improving the durability and reliability of PSCs and minimodules, while simultaneously enhancing their PCE. This is achieved by incorporating rationally-chosen self-assembled monolayers (SAMs) at key PSC interfaces. Inherently scalable methods for the deposition of MHP light-absorber thin films and SAMs are employed to ensure a viable path towards manufacturability. Furthermore, detailed understanding of mechanisms of PSCs and minimodules degradation, and SAMs-induced mitigation, is provided. As part of the project accomplishments, >60% increase in the adhesion toughness of the key PSC interfaces over their SAMs-free control counterparts was achieved. Also, PCEs >20% and >19% in rigid and flexible, respectively, single-junction PSCs (~1 cm 2 area) were achieved. It was shown that <20% PCE loss in flexible PSCs with SAMs can be achieved after bend testing. It was demonstrated that T80 (80% retention of initial PCE) of >5,000 hours in rigid PSCs (~1 cm2 area) can be achieved. Comprehensive understanding of the degradation mechanisms in PSCs was obtained. These strategies were adopted towards developing minimodules. PCE of >21% was obtained in an 6-cm 2 area minimodule, with T91 of 1,000 hours.

14 SOLAR ENERGY↗
DOE OSTI2024

Metal Halide Perovskite Solar Module Encapsulation Using Polyolefin Elastomers: The Role of Morphology in Preventing Delamination

The development of perovskite solar cells (PSCs) has ushered in a new era of solar technology, characterized by its exceptional efficiency and cost-effective production. However, the soft and fragile nature of perovskites makes module encapsulation challenging. Polyolefin elastomers (POEs) have been reported to be promising encapsulants for perovskite modules. However, little research exists on identifying criteria among different types of POEs as encapsulants. Here, two POEs with different morphologies were compared as encapsulants. The first POE crystallizes during encapsulation (crystal content ∼40%), and the resulting shrinkage or warpage leads to delamination, causing minimodule failure. In contrast, perovskite minimodules encapsulated with a mostly amorphous POE exhibited better reliability and reproducibility. The best perovskite minimodules passed the thermal cycling test for 240 cycles between −40 and 85 °C and the damp heat test for 1419 h, according to the IEC 61215 standard. This study highlights the importance of the morphology of encapsulants in achieving high-quality encapsulation. Published by the American Physical Society 2024

14 SOLAR ENERGY↗
DOE OSTI2022

Network Models of Active Degradation Mechanisms and Pathways for Service Life Prediction of Indoor and Outdoor PV Modules

ct: PV service lifetime prediction (SLP) enables accurate calculation of levelized cost of energy (LCOE), which is crucial to rationalizing PV investment and installation. However, SLP is challeging since PV reliability in the field is affected by many combined factors, including various environmental stresses and module quality. In order to map out the active degradation mechanisms and pathways that best resemble real world conditions, we introduce the framework of a study protocol and use network models fitted to data, to enable analysis and SLP of complex PV systems with multiple active degradation mechanisms. The study protocol is the experimental design, including module variants and different exposure conditions, selection of evaluation methods, time-series data acquisition and training of network models to these data. We present SLP of minimodules in the lab and PV systems in the field. For lab SLP, minimodules with 8 variants based on manufacturer, architecture, and encapsulation were prepared and aged in modified damp heat with or without full spectrum light exposure. Stepwise I-V and Suns-Voc data acquisition tracks changes in electrical properties including Rs,IV, Isc,IV, Vmp,PIV providing insights into power loss of minimodules. Network structural equation modeling (netSEM) was utilized to construct degradation pathway models that identify active degradation mechanisms and predict power loss over time. For field SLP, datastreams of Pmp values and I-V curve datastreams of two types of modules installed in three distinctly different Köppen-Geiger climate zones for 9 years were acquired. With power loss modes corresponding to uniform current loss (ΔPIsc), recombination (ΔPVoc), series resistance (ΔPRs), and current mismatch (ΔPImis) determined, the performance loss rates (PLR) were determined using PVplr. We show how to establish a study protocol framework to ensure appropriate parametric variations and valid data collection from the variants of your complex systems. Then the data-driven netSEM model fitting provides a comprehensive mapping of multiple active degradation mechanisms, and accurate service life prediction.

network model, degradation, photovoltaic, solar↗
DOE OSTI2023

Tailoring Crystallization Dynamics of CsPbI 3 for Scalable Production of Efficient Inorganic Perovskite Solar Cells

All-inorganic perovskite cesium lead triiodide (CsPbI 3 ) with inorganic nature, low-temperature synthesis, and a suitable bandgap is desirable for high-performance photovoltaics. However, the scalable production of CsPbI 3 photovoltaics is still challenging due to a large nucleation energy barrier and slow phase transition during unassisted natural crystallization. Here, the crystallization dynamics of CsPbI 3 thin films is tailored via lead acetate (PbAc 2 ) substitution in the perovskite precursor ink, allowing the scalable fabrication of efficient all-inorganic perovskite solar cells and minimodules. Introducing PbAc 2 enlarges CsPbI 3 colloid size in the precursor and reduces the nucleation energy barrier. Additionally, reactions between acetate and dimethylammonium in the wet film accelerate the removal of dimethylammonium additives and generate solvent vapors for self-regulate internal solvent annealing, resulting in densely packed, uniform, and pinhole-free CsPbI 3 perovskite films over large areas. This strategy demonstrates inverted CsPbI 3 solar cells with 20.17% efficiency and good operational stability (retaining 95.5% of initial efficiency after continuous operation for 1800 h) and 15.1%-efficient CsPbI 3 minimodules with an active area of 26.8 cm 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Surface engineering with oxidized Ti 3 C 2 T x MXene enables efficient and stable p-i-n-structured CsPbI 3 perovskite solar cells

All-inorganic CsPbI 3 perovskite has a near-ideal band gap, high thermal stability, and simple material composition, thus presenting a promising option for developing perovskite/Si tandem solar cells. However, CsPbI 3 undergoes a rapid phase transition under exposure to moisture and exhibits a significant performance gap relative to other perovskite compounds, particularly in the p-i-n structure favored for perovskite/Si tandems. In this work, we demonstrate highly efficient and stable p-i-n-structured CsPbI 3 perovskite solar cells by surface engineering the CsPbI 3 layer with oxidized Ti 3 C 2 T x MXene (OMXene) nanoplates via spray coatings. OMXene provides a physical barrier against moisture and improves charge separation at the perovskite-electron transporting layer interface via an enhanced electric field. Consequently, we demonstrated CsPbI 3 /OMXene-based p-i-n devices with efficiencies of 19.69% for 0.096-cm 2 cells and 14.64% for 25-cm 2 minimodules. The encapsulated minimodule showed good stability, retaining ~85% of the initial efficiency under simultaneous damp heat (85°C/85% relative humidity) and 1-sun light soaking for over 1,000 h.

14 SOLAR ENERGY↗