Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microcontroller”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Thermal neutron-induced single-event upsets in microcontrollers containing boron-10

Single-event upsets (SEUs) were measured in thermal neutron-irradiated microcontrollers with 65-nm node and 130-nm node SRAMs. The suspected upset mechanism is charge deposition from the energetic byproducts of 10 B thermal neutron capture. Although elemental analysis confirmed that both microcontrollers contain 10 B, only the 65-nm node microcontroller exhibited a strong response to thermal neutrons. Monte Carlo simulations were performed to investigate the effects of 11 B enrichment on thermal neutron-induced SEUs in a 65-nm SRAM node when boron is present in the p -type well, p -type source and drain, or tungsten plug. Simulations indicate that the byproducts of 10 B(n,α) 7 Li reactions are capable of generating sufficient charge to upset a 65-nm SRAM. Finally, the highest amount of charge deposition from 10 B(n,α) 7 Li reaction byproducts occurs when natural boron is used to dope the p -type source and drain regions. Simulations also show that the SEU cross section is non-negligible when 11 B-enriched boron is used for doping.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Microcontroller-based aerosol jet printer control software

This software is used with a microcontroller to control an aerosol jet printing system. It was written for a 32-bit ARM microcontroller, providing greater processing speed and complexity relative to more conventional low-cost printer controllers. The microcontroller software was written using a real-time operating system (FreeRTOS), which simplifies parallel operation of multiple functions and further customization. It supports simultaneous motion planning, pulse generation for stepper motors, reading encoder feedback, communicating with multiple mass flow controllers, controlling solid state relays, handling a software-based emergency stop, and sending data to the client PC. The program is written in C and communicates with the client PC via USB connection. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. SAND2021-0436 O

Secor, EthanBenjamin↗
DOE OSTI2021

Multi-Core Microcontroller Hardware In the Loop System for Electric Machine Control

Hardware in the Loop (HIL) is a simulation technique used to reduce the software development cycle and test control systems in a non-destructive environment. This work describes a cost effective HIL simulator on a dual core microcontroller in which one core acts as a controller and the other emulates the system under control. The emulator runs one step per Pulse Width Modulation (PWM) period in real time. To handle the computational burden and prioritize execution of simulation and control tasks, an interrupt-based software architecture with task prioritization has been developed. As a demonstration, the HIL has been implemented on a Texas Instruments TMS320F28379D dual core microcontroller, which emulates a Permanent Magnet Synchronous Machine (PMSM) with resolver feedback. Hardware peripherals are developed and tested concurrently with the control system, providing higher confidence in the software. By using the peripherals in the HIL development, the controller exercises either the HIL emulation or a pin compatible PMSM testbench. To quantify performance and validate the processor based emulator, the HIL results are compared to the preexisting testbench for accuracy benchmarking at no-load and under load for a range of operating points.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

A microchip microcontroller-based transducer controller for non-contact scanning probe microscopy with phase-locked loop, amplitude, and Q control

An inexpensive yet versatile transducer controller for non-contact scanning probe microscopy (SPM) based on a PIC32 microcontroller from Microchip Technology, Inc is described. In addition to feedback control using the amplitude or phase of the signal from the non-contact transducer, the controller includes a phase-locked loop for frequency-shift feedback, as well as fixed-amplitude, quality factor (Q) control, and self-excitation modes. Apart from the input amplifiers, output buffers, and the Q-control circuit, all other functions of the controller are instantiated in software on the microchip, enabling rapid changes in operating parameters if needed. The controller communicates with a host personal computer via a simple serial connection. The controller has been tested with a quartz tuning-fork transducer but can be used with any oscillating non-contact transducer.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Reactor System Demonstration with Cyber-Attack Scenarios Using CrowPis and Arduino Microcontrollers

This study covers developing and simulating nuclear reactor system using CrowPis and Arduino microcontrollers for demonstrating cyber-attack scenarios. The team was tasked with implementing more sensors and cybersecurity aspects to the reactor program that was created by last year’s high school interns. The team received the opportunity to collaborate and obtain advice from multiple university interns that helped us gain a better perspective of our project. Our mentor’s background in nuclear science was pivotal to our understanding what we could add to the reactor program to make it as realistic as possible. The first week of our internship was spent reading as much material as possible to gain an understanding of and the background for cyber-attacks and nuclear science. Nuclear science was a new horizon for each of the high school interns on the team, so spending this time in the beginning of our internship was crucial to our success. For the remaining portion of our internship, the team collectively did our best to implement as many sensors and use as much hardware as we could to make an accurate representation of a nuclear reactor in the program that was created. This internship was a big learning experience for everyone on the team. We all gained so many insights into the nuclear world and how it can benefit our lives, as well as how so many moving pieces are needed for it to work properly.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2014

Microcontroller-based locking in optics experiments

Optics experiments critically require the stable and accurate locking of relative phases between light beams or the stabilization of Fabry-Perot cavity lengths. Here, we present a simple and inexpensive technique based on a stand-alone microcontroller unit to perform such tasks. Easily programmed in C language, this reconfigurable digital locking system also enables automatic relocking and sequential functioning. Different algorithms are detailed and applied to fringe locking and to low- and high-finesse optical cavity stabilization, without the need of external modulations or error signals. This technique can readily replace a number of analog locking systems advantageously in a variety of optical experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

Microcontroller-based system for analyzing and characterizing solar panels

A solar cell is one of many alternative energy which is still being developed and it works by converting sunlight into electricity. In order to use a solar cell, a deep knowledge about the solar cell’s characteristics is needed. The current and voltage (I-V) produced when the light hits the solar cell surface with a certain value of intensity and at a certain value of temperature becomes the basic study to determine solar cell characteristics. In the past decade, there were so many developments of devices to characterize solar cells and solar panels. One of them used a MOSFET device for varying electronic load to observe solar cell current and voltage responses. However, many devices which have been developed even device on the market using many expensive tools and quite complex. Therefore in this research, a simple low cost electronic controlled device for solar cell characterization is built based on MOSFET method and a microcontroller but still has high reliability and accuracy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2019

Effect of Radio-Frequency and Ionizing Radiation on the ATmega8515 Microcontroller

Effect of ultrabroadband radiation and bremsstrahlung on a complicated device (ATmega8515) placed in a radio-transparent housing is studied. Similar results are obtained in the two cases: short-term malfunction or hangup. A particular scenario depends on the moment of irradiation relative to the phase of the meander generated by the microcontroller. In the presence of bremsstrahlung, the effect depends on the exposure dose, so that an increase in the duration of the generated phase or hangup can be obtained.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Update to the Microcontroller Benchmark for Radiation Testing

LANL developed a benchmark of software code for radiation testing of microprocessors several years ago, and it was published under an open-source license on GitHub. Publishing the software is necessary for other researchers to adopt and implement this benchmark for radiation testing of other microprocessors to standardize test practices so that test data can be compared across different microprocessors. The original codes have been used several times by other organizations to test a wide range of microcontrollers and microprocessors. After several years of research, LANL is ready to update the benchmark. Changes include: 1. Addition of new codes that allow common software codes to be tested, 2. Addition of new codes that instrument more microprocessor circuitry, 3. Addition of input patterns that allow for a more compressive understanding of how the memory layout affects the sensitivity to radiation-induced faults and better use of automated test pattern generation standards, and 4. Modification of current codes for faster and more resilient detection, reporting and correction of radiation-induced faults. These codes have been tested by LANL researchers over the last few years, which has been published in the open literature. As the code base for the new benchmarks are stable, it is time to release the update to the GitHub repository, where the original codes were released.

Quinn, Heather↗
DOE OSTI2014

Embedded image processing engine using ARM cortex-M4 based STM32F407 microcontroller

Due to advancement in low cost, easily available, yet powerful hardware and revolution in open source software, urge to make newer, more interactive machines and electronic systems have increased manifold among engineers. To make system more interactive, designers need easy to use sensor systems. Giving the boon of vision to machines was never easy, though it is not impossible these days; it is still not easy and expensive. This work presents a low cost, moderate performance and programmable Image processing engine. This Image processing engine is able to capture real time images, can store the images in the permanent storage and can perform preprogrammed image processing operations on the captured images.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Software resilience and the effectiveness of software mitigation in microcontrollers

Commercially available microprocessors could be useful to the space community for noncritical computations. There are many possible components that are smaller, lower-power, and less expensive than traditional radiation-hardened microprocessors. Many commercial microprocessors have issues with single-event effects (SEEs), such as single-event upsets (SEUs) and single-event transients (SETs), that can cause the microprocessor to calculate an incorrect result or crash. In this paper we present the Trikaya technique for masking SEUs and SETs through software mitigation techniques. Furthermore, test results show that this technique can be very effective at masking errors, making it possible to fly these microprocessors for a variety of missions.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2016

Robust Duplication with Comparison Methods in Microcontrollers

Commercial microprocessors could be useful computational platforms in space systems, as long as the risk is bound. Many spacecraft are computationally constrained because all of the computation is done on a single radiation-hardened microprocessor. It is possible that a commercial microprocessor could be used for configuration, monitoring and background tasks that are not mission critical. Most commercial microprocessors are affected by radiation, including single-event effects (SEEs) that could be destructive to the component or corrupt the data. Part screening can help designers avoid components with destructive failure modes, and mitigation can suppress data corruption. We have been experimenting with a method for masking radiation-induced faults through the software executing on the microprocessor. While triple-modular redundancy (TMR) techniques are very effective at masking faults in software, the increased amount of execution time to complete the computation is not desirable. Here in this article we present a technique for combining duplication with compare (DWC) with TMR that decreases observable errors by as much as 145 times with only a 2.35 time decrease in performance.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Internship Work Report

I worked on two projects during my summer internship at Sandia. My official title was “Intern - Mission Tech Electrical Eng./Computer Eng.- R&D Undergraduate Summer.” I worked at the central location, which is Albuquerque, New Mexico. The department you are placed in at Sandia doesn’t always correspond to the people you will be working with. For example, I only directly worked with one person from my department this summer. On one of my projects, I worked with a diverse team of engineers from many different departments. On my other project, I mainly worked with two departments, as the project had two distinct parts. As mentioned earlier, I worked on two projects during my summer at Sandia. The first project focused on a lightweight embedded controller in an advanced FPGA System-on-Chip for radar signal processing applications. The term “controller” refers to a hardware device that directs the flow of data between two entities. An FPGA is a reprogrammable integrated circuit (as opposed to an integrated circuit with one purpose). An FPGA was used on this project so in order to protype various ideas for our System-on-Chip. My role on the project was to implement designs on the fabric of the FPGA and design a state machine (written in C) for the processor. My second project was also heavily involved with embedded systems but had a different application. It focused on using a Newton-Raphson control algorithm to stabilize an inverted pendulum using a novel microcontroller. The pendulum dynamics were derived, and it was successfully simulated in MATLAB. I worked on integrating the microcontroller with the inverted pendulum machinery, and converting the Newton-Raphson control algorithm from MATLAB into C. The inverted pendulum was successfully stabilized using a simple PID controller and industry-standard microcontroller. The project is still ongoing, and the team is gearing up for more tests using the novel Newton-Raphson control algorithm and novel microcontroller

42 ENGINEERING↗