Metal-oxide-metal, M-O-M, detector
Metal-oxide-metal tunnel diode properties, discussing parametric effects on small and large signals detector operation
Haddad, G. I.↗
SEARCH · Engineering Papers
Results for “metal oxides”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Metal-oxide-metal point contact junction detectors
The detection mechanism(s) and design of a mechanically stable metal-oxide-metal point contact junction detector are considered. A prototype for a mechanically stable device has been constructed and tested. A technique has been developed which accurately predicts microwave video detector and heterodyne mixer SIM (semiconductor-insulator-metal) diode performance from low dc frequency volt-ampere curves. The difference in contact potential between the two metals and geometrically induced rectification constitute the detection mechanisms.
Baird, J.↗
Coupling characteristics of thin-film metal-oxide-metal diodes at 10.6 microns
Direct detection experiments have demonstrated the coherent coupling of 10.6 micrometer radiation into photolithographically fabricated metal-oxide-metal tunnel junctions. A CO2 laser beam mechanically chopped at 1 KHz was focused at a variable angle of incidence with a power density of about 10 W/sq cm at the diodes. Diodes in which the junction resistance was much greater than the lead resistance displayed angular characteristics dominated by coherent antenna coupling.
Wang, S. Y.↗
Oxide film on metal substrate reduced to form metal-oxide-metal layer structure
Electrically conductive layer of zirconium on a zirconium-oxide film residing on a zirconium substrate is formed by reducing the oxide in a sodium-calcium solution. The reduced metal remains on the oxide surface as an adherent layer and seems to form a barrier that inhibits further reaction.
Youngdahl, C. A.↗
Dynamics of inverse metal oxides on metal catalysts using spectro-kinetics: reversible Brønsted acid site formation and irreversible reduction
Brønsted acid sites (BASs) in inverse catalysts are vital for the selective hydrogenolysis of polyols, specifically cleaving secondary C–O bonds. These BASs form dynamically in situ in an H 2 environment. While H 2 enables rapid BAS generation on short timescales, it reduces the catalyst at prolonged exposures. The active center for BAS generation, the kinetics of BAS formation, its reverse decomposition, and the irreversible oxide reduction have lacked direct experimental evidence. Here, aided by advanced spectro-kinetic studies, we identify trimeric W 3 O x sites on Pt as the active centers for BAS generation, whereas isolated WO x species on SiO 2 act merely as spectator species, demonstrated using an inverse WO x /Pt catalyst as a representative system. A detailed kinetic profile capturing the dynamics of W 3 O x sites on Pt is also established. The rate constant for BAS formation is two orders of magnitude higher than for its decomposition, which is one order of magnitude faster than the irreversible site reduction. Co-fed H 2 O suppresses the site reduction by ∼50%. Furthermore, the H 2 partial pressure plays an important role. While lower gas-phase H 2 partial pressure does not influence the reversible BAS formation, it can significantly (∼3×) suppress catalyst reduction. Finally, these findings offer critical insights into optimizing reaction conditions through periodic H 2 pulsing, enhancing catalyst stability and performance in hydrogenolysis reactions.
Sourav, Sagar [Indian Inst. of Technology (IIT), M↗
A General Solution Route to Nanoporous Metal Oxide Films
Metal oxide semiconductors are of interest as efficient, stable, and low-cost photoanode materials for photoelectrochemical water splitting, but their characteristically poor charge transport properties remain a fundamental challenge to practical use. Nanoporous metal oxide films that feature open bicontinuous networks of nanocrystals and nanopores can overcome such inefficient charge transport to enable high-performance photoanodes. Here, this paper describes a general method to make high-quality nanoporous films of metal oxides by spin coating and calcining molecular inks that contain a porosity-generating block copolymer. Phase-pure nanoporous films of BiFeO 3 , FeWO 4 , WO 3 , Fe 2 O 3 , and TiO 2 serve to demonstrate the versatility of the approach. It is demonstrated that the crystallite size, film porosity, and film thickness can be independently tuned by adjusting the ink composition and film processing conditions. The method is extended to fabricate core–shell nanoporous films consisting of a nanoporous film coated in a thin shell of a second metal oxide, using WO 3 –BiVO 4 and BiFeO 3 –BiVO 4 as examples. Given its simplicity and flexibility, this solution-phase route should prove useful for making nanoporous films of many different materials for a variety of applications, including energy conversion and storage, catalysis, and chemical sensing.
coating materials↗
Porogen‐Integrated Rapid Oxidation Enables Structured Mesoporous Metal Oxide Films
Structured metal oxide films have promise in optoelectronics, sensing, energy storage, and catalysis but their uptake is predominately limited due to their long and high‐temperature syntheses. Here, in this study, a self‐assembling polymer is used which can act as a chelating fuel source in a solution combustion reaction to generate highly structured mesoporous aluminum oxide films at <250 °C in a matter of minutes through a process termed porogen‐integrated rapid oxidation (PiRO). The resulting films with thicknesses up to 500 nm show an open‐cell, face‐centered cubic structure of spheroidal pores. Further, an additional ligand can be included to control the self‐assembly step to yield both through‐film ordering or tunable disordering for increased pore volume as confirmed by both grazing incidence small angle X‐ray scattering and ellipsometry. Finally, roll‐to‐roll manufacturing with PiRO is demonstrated on flexible polymeric substrates. The method offers a tunable, scalable, low‐temperature, and lower‐cost method to generate large‐area structured mesoporous metal oxide films.
36 MATERIALS SCIENCE↗
Tuning the Selectivity of Carboxylic Acid–Based Eutectic Solvents for the Dissolution and Electrochemical Separation of Metal Oxides
Extracting metals from natural resources and recovering from waste materials with less-hazardous solvents is essential for sustainable technological advancements. The commonly employed method utilizes harsh chemicals for metal dissolution and the ensuing separation. Here, in this study, we examined the potential of eutectic solvents (types III and IV) as alternative media for the selective dissolution of metals and metal oxides and their subsequent electrochemical separation. Notably, type III eutectics composed of betaine:acetic acid and triazole:lactic acid exhibited excellent solubility for cobalt oxide (24.1 g·L –1 ) and copper oxide (30.5 g·L –1 ), respectively. In comparison, the type IV eutectic mixture of Ca(NO 3 ) 2 ·4H 2 O:acetic acid demonstrated the highest conductivity and lowest viscosity with solubility for both copper oxide (6.1 g·L –1 ) and metallic copper (5.4 g·L –1 from a used electronic circuit). Using a Ca(NO 3 ) 2 ·4H 2 O:acetic acid mixture, copper was selectively dissolved from a waste printed circuit board and subsequently electrodeposited onto a nickel electrode. These findings highlight the tunability of DESs for the selective recovery of metals from electronic waste, offering a promising approach for sustainable metal recycling and resource recovery.
electrodeposition↗
Injection and migration of charges in the oxide of a metal-oxide-semiconductor structure
Injection of charges in oxide of metal oxide semiconductor structure
Saminadayar, K.↗
The MSFC complementary metal oxide semiconductor (including multilevel interconnect metallization) process handbook
The fabrication techniques for creation of complementary metal oxide semiconductor integrated circuits at George C. Marshall Space Flight Center are described. Examples of C-MOS integrated circuits manufactured at MSFC are presented with functional descriptions of each. Typical electrical characteristics of both p-channel metal oxide semiconductor and n-channel metal oxide semiconductor discrete devices under given conditions are provided. Procedures design, mask making, packaging, and testing are included.
Bouldin, D. L.↗
Measurements of Total Hemispherical Emissivity of Several Stably Oxidized Metals and Some Refractory Oxide Coatings
A description of the apparatus and methods used for obtaining total hemispherical emissivity is presented, and data for several stably oxidized metals are included. The metals which were tested included type 347 stainless steel, tungsten, and Haynes alloys B, C, X, and 25. No values of emissivity were obtained for tungsten or Haynes alloy B because of the nature of the oxides produced. The refractory oxide coatings tested were flame-sprayed alumina and zirconia. The results of the investigation indicate that strongly adherent, oxidized surfaces of a high stable emissivity can be produced on type 347 stainless steel for which the total hemispherical emissivity varied from 0.87 to 0.91 for temperatures from 600 F to 2,000 F. For this same temperature range, the Haynes alloys tested showed values of total hemispherical emissivity from 0.90 to 0.96 for alloy C, from 0.85 to 0.88 for alloy X, and from 0.85 to 0.89 for alloy 25. Haynes alloy B and tungsten formed nonadherent oxides at elevated temperatures and, therefore, stable emissivities were not obtained. The results obtained for the flame-sprayed ceramics (alumina and zirconia) showed considerably higher values of total emissivity than those measured for coatings applied by other methods. Emissivity values ranging from 0.69 to 0.44 for aluminum oxide and from 0.62 to 0.44 for zirconium oxide were measured for temperatures from 800 F to 2,000 F.
Wade, William R.↗
Fermi Level Equilibration and Charge Transfer at the Exsolved Metal-Oxide Interface
Exsolution is a promising approach for fabricating oxide-supported metal nanocatalysts through redox-driven metal precipitation. A defining feature of exsolved nanocatalysts is their anchored metal-oxide interface, which exhibits exceptional structural stability in (electro)catalysis. However, the electronic interactions at this unique interface remain unclear, despite their known impact on catalytic performance. In this study, we confirm charge transfer between the host oxide and the exsolved metal by demonstrating a two-stage Fermi level ( E F ) evolution on SrTi 0.65 Fe 0.35 O 3−δ (STF) during metallic iron (Fe 0 ) exsolution. Combining ambient pressure X-ray photoelectron spectroscopy with theoretical analysis, we show that E F initially rises due to electron doping from oxygen vacancy formation in STF. Subsequently, upon Fe 0 precipitation, E F stabilizes and becomes insensitive to further oxygen release in STF, driven by E F equilibration and charge transfer between STF and the exsolved Fe 0 . In conclusion, these findings highlight the importance of considering electronic metal–support interactions when optimizing exsolved nanocatalysts.
36 MATERIALS SCIENCE↗
Elucidating the role of surface species in CO oxidation catalyzed by boron nitride nanotube supported transition metal oxides
Boron nitride nanotube (BNNT) is considered a highly promising catalyst support due to its outstanding thermal stability and chemical inertness. These characteristics make BNNT an attractive alternative for high-temperature applications. However, most studies to date have focused on incorporating platinum group metals (PGMs) to achieve high activity. Although BNNT-supported PGM catalysts are highly effective, their scarcity and high cost hinder widespread use in industrial processes. In this study, BNNT-supported transition metal oxides (TMO x /BNNT; TM = Fe, Co, Ni, and Cu) catalysts were investigated, and CO oxidation was applied as a model reaction to evaluate their catalytic performance. Several characterization techniques, including SEM-EDX, TEM, SXRD, H 2 -TPR, and XPS, were employed to examine their physicochemical properties. Notably, the particle size of the metal oxides differed significantly depending on the metal type. This variation is primarily attributed to the inherent metal–support interactions and the thermodynamic stability of each oxide during synthesis. These properties also affected catalytic activity, and various parameters, such as oxygen mobility and redox behavior, played important roles in determining performance. Finally, in situ DRIFTS, CO-TPSR, reaction-order analysis, and 18 O 2 isotope-labeling experiment were used to investigate the reaction mechanism. In conclusion, the findings provide insights into the design of cost-effective BNNT-supported catalysts and highlight their potential applicability in oxidation reactions.
36 MATERIALS SCIENCE↗
Alkali-induced catalytic tuning at metal and metal oxide interfaces
Alkali metals have been recognized as effective promoters in heterogeneous catalysis, capable of enhancing catalytic activity and tuning product distributions. Over the past few decades, significant efforts have been made aiming to reveal the mechanisms underlying the promoting effect of alkalis. However, the roles that alkali metals play in the catalytic process remain elusive due to challenges in capturing their catalytic behaviours upon exposure to reactive environments. This review summarizes recent surface science and theoretical studies of alkali (potassium, cesium)-decorated metal and metal oxide model catalysts, revealing the crucial tuning by alkalis of activity and selectivity for CO 2 hydrogenation. The analysis of electronic structures identifies the selective binding mechanism of the positively charged alkali ions on the surface, being able to reduce the surface work function and lead to strong electron polarization on the surfaces. Depending on the alkali–support interaction, the deposition of alkalis can selectively modify the bindings of reaction intermediates involved in CO 2 hydrogenation via the interplay among the ionic, covalent and electrostatic tunings. As a result, CO 2 can be effectively activated and converted into diverse products at the alkali–support interface, ranging from formic acid to methanol and ethanol. The identified selective bond-tuning advances the application of alkalis in promoting catalytic activity and controlling catalytic selectivity at alkali–support interfaces.
03 NATURAL GAS↗
Lead oxide /pbo/ and other metal oxides as solid lubricants for temperatures to 1000 deg f
Explore the source record for details and available documents.
Johnson, R. L.↗
Monolayer Films of Binary Metal Oxide Nanoparticles for Carbon Nanotube Synthesis
Binary metal oxide nanoparticles (biMO-NPs) combining transition and main-group metals with well-organized atomic architectures have unique potential as robust and economical heterogeneous catalysts. Herein, metal oxide nanoparticles (CoAlxOy) using cobalt and aluminum were synthesized, and their structure, morphology, and chemical composition were investigated using various characterization techniques. The biMO-NPs, which had a Gaussian-type size distribution (∼6 nm), were assembled on plain silicon substrates modified chemically with linker molecules bearing suitable end groups. Surface analysis revealed an ordered, uniform, close-packed arrangement of biMO-NPs forming a monolayer architecture with nanoscale thickness (∼12 nm), high surface uniformity, and negligible defects. The nanoparticle monolayer film (NP-MF) was employed as a catalyst to grow carbon nanotube (CNT) forests via the thermal chemical vapor deposition (CVD) method, similar to those grown from catalyst thin films deposited by physical vapor deposition. Structural characterization confirmed the growth of a dense, uniform, high-quality vertically aligned carbon nanotube (VA-CNT) forest with a length of ∼125 µm, which is comparable to the VA-CNTs grown from expensive thin films. Thus, CNT growth was successfully catalyzed by the biMO-NPs, highlighting a simple and inexpensive alternative for catalyst deposition. In this innovative wet-chemistry approach, the catalyst and catalyst support are combined within a single nanoparticle before NP-MF assembly. Interestingly, this approach provides a scalable and cost-effective pathway for CNT growth, eliminating the need for expensive thin deposition techniques.
Regmi, Bishow [University of Cincinnati]↗
Fundamental Insights into Cathode Stability: Linking Compositional Tuning and Local Coordination in Complex Metal Oxides under Aqueous Transformations
Compositional tuning of complex metal oxides in Li-ion battery materials influences their performance as well as their end-of-life behavior, in particular, the tendency to release toxic metal cations in aqueous solution. We modeled ternary variants of a parent LiCoO 2 delafossite structure by varying the metal identity and relative amounts. This yielded ten model formulations of Li(A 4/6 B 1/6 C 1/6 )O 2 , where the material is enriched with the A metal and doped with B and C, with Ni, Mn, Co, Fe, Al, V, and Ti as constituent metals. To assess their stability in aqueous conditions, metal release energetics were calculated using a combination of Density Functional Theory calculations and thermodynamics. Metal release in ternary oxides is dictated by subtle variations in the coordination environment of the leaving group. To identify governing chemical features across diverse compositions with varying local coordination environments, we leverage random forest regression and descriptor importance analysis. A key result is that metal–oxygen orbital hybridization, quantified using a projected density-of-states-derived descriptor, H d/p , provides a physically grounded measure of interaction strength that governs metal release energetics. This refined perspective goes beyond conventional oxidation state considerations and offers more robust insights for materials science. Finally, we model defect surface-bound O 2 dimer formation as a proxy for reactive oxygen species (ROS) generation. The results show that Ni-rich compositions more readily stabilize spin-polarized O 2 dimers, corroborating experimental reports of an increased ROS-driven biological response. In conclusion, our results establish a compositional and electronic basis for metal release and surface oxygen reactivity that form a rationale for complex metal oxide design principles.
36 MATERIALS SCIENCE↗