Soothing Science: Scientific glass blowing
Melt away the stress of your day with some #SoothingScience. Glassblowers at ORNL fabricate custom scientific equipment that helps make the lab’s research possible.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Melt away the stress of your day with some #SoothingScience. Glassblowers at ORNL fabricate custom scientific equipment that helps make the lab’s research possible.
This work investigates the scale-up of pitch precursors for the carbon fiber market using mesophase pitch formulated and produced by Advanced Carbon Products Technologies’ (ACPT’s) patented mesophase pitch processing technology. Through use of its patented process, ACPT developed strategic materials by converting petroleum-based pitch into a high-value, low-cost, carbon-rich feedstock for carbon fiber and other materials critical to our national security. The team successfully developed processing criteria for the tailored mesophase pitch material that can be processed further into precursor and carbon fiber. Processability of the mesophase pitch into precursor and carbon fiber was demonstrated at scale. The resulting materials sequester the carbon that would otherwise be burned and released into the atmosphere, making this an environmentally friendly way to produce these materials in the United States.Pitch-based carbon fibers offer a promising pathway toward cost-effective, high-performance materials for structural and high-modulus composite applications; however, adoption has been limited by challenges in precursor processability and scale-up. In this work, tailored isotropic and mesophase petroleum-derived pitch materials were developed and evaluated for precursor and carbon fiber production through a collaborative effort between Oak Ridge National Laboratory (ORNL) and ACPT. Processing conditions were established at ORNL’s Carbon Fiber Technology Facility to enable stable melt-blowing of pitch-based precursors under continuous operation. Mesophase pitch precursor fibers were produced following oxidation and carbonization, corresponding to a diameter shrinkage of approximately 12%–13% and an estimated mass yield of about 75%–80%. Continuous melt-blowing steady-state operation was demonstrated over time, indicating robust process stability. Melt-blowing was achieved at throughput rates of approximately 20 lb/h⁻¹, validating the commercial viability of petroleum-derived pitch feedstocks for fiber production. Further studies are required to tailor carbon fiber microstructure and properties for specific composite applications.
This report documents activities carried out by Oak Ridge National Laboratory and by Ramaco Carbon LLC under CRADA project NFE-20-08273 entitled “Coal to Carbon Fibers.” This project’s main objective was the demonstration of commercially relevant utilization of coal as a precursor for high-value-added products, such as carbon fibers. The specific objectives included the following: • Deploy a production platform for the conversion of coal into carbon fibers in a way that utilizes preexisting base technologies and accelerates the commercialization of coal to carbon fibers. • Rapid deployment and utilization of versatile conversion test beds for accommodating preexisting base technologies for both the conversion of coal-to-pitch (proven donor solvent liquefaction techniques) and conversion of pitch-to-fiber (proven melt spun and melt blown techniques). Results from the generation of an isotropic pitch from a subbituminous coal through the low severity direct coal liquefaction process are presented. Carbon fibers were produced from this isotropic pitch through melt spinning and melt blowing.
Lignin, a low-cost, biomass derived precursor, was selected as an alternative for carbon based free standing anodes in Li-ion batteries. Industrially scalable melt-spinning and melt-blowing synthesis methods were developed at Oak Ridge National Laboratory that are compatible with industrially viable production. Engineering studies predict that LCFs can be manufactured at $3/lb using these technologies, which compares favorably to $12/lb for battery grade graphite. The physical properties of lignin carbon fibers, specifically the tunable electrochemical and thermal transport, are suitable for energy storage applications as both an active material and current collector. The elimination of inactive components in the slurry-coated electrodes was enabled by LCF processing parameters modifications to produce monolithic mats in which the fibers are electrically interconnected. These mats were several hundreds of micrometers thick, and the fibers functioned as both current collector and active material by virtue of their mixed ionic/electronic conductivities. The LCFs were coated onto copper current collectors with PVDF binder and conductive carbon additive through conventional slurry processing. Galvanostatic cycling of the LCFs against Li revealed reversible capacities greater than 300 mAh/g. The coulombic efficiencies were over 99.8%. The mats were galvanostatically cycled in half cells against Li. Specific capacities as high as 250 mAh/g were achieved approximately 17% lower than the capacities of the same fibers in slurries. However, there were no inactive materials reducing the practical specific capacity of the entire electrode construction. Lithiation and delithiation of the LCFs proceeded with coulombic efficiencies greater than 99.9%, and the capacity retention was greater than 99% over 100 cycles at a rate of 15 mA/g. Research sponsored by the Laboratory Directed Research and Development Program of Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the U. S. Department of Energy.
For Earth-impacting objects that are large in size or have short warning times nuclear explosives are an effective threat mitigation response. Nuclear-based deflection works by means of conservation of momentum: as material is heated by incoming photons and neutrons it is ejected from the body which imparts momentum to the remaining mass of the asteroid. Predicting the complete response of a particular object is difficult, since the ejecta size and velocity distributions rely heavily on the unknown, complicated internal structure of the body. However, lower bounds on the blow-off momentum can be estimated using the melted and vaporized surface material. In this paper, we model the response of a one-dimensional SiO2 surface to monoenergetic soft X-ray, hard X-ray and neutron sources using Arbitrary Lagrangian–Eulerian radiation/hydrodynamic simulations. Errors in the blow-off momentum due to our hydrodynamic mesh resolution are quantified and inform zone sizing that balances numerical discretization error with computational efficiency. We explore deposited energy densities ranging from 1.1 to 200 times the melt energy density for SiO2, and develop an approximate relation that gives the mesh resolution needed for a desired percent error in the blow-off momentum as a function of deposited energy density and melt depth. Using these mesh constraints, the response of our one-dimensional SiO2 surface to the energy sources is simulated, and lower bounds are placed on the melt/vapor blow-off momentum as a function of deposited energy density and source energy type.
The current severe acute respiratory syndrome coronavirus 2 (SARS-COV-2) pandemic has highlighted the need for personal protective equipment, specifically filtering facepiece respirators like N95 masks. While it is common knowledge that polypropylene (PP) is the industry standard material for filtration media, trial and error is often required to identify suitable commercial precursors for filtration media production. This work aims to identify differences between several commercial grades of PP and demonstrate the development of N95 filtration media with the intent that the industry partners can pivot and help address N95 shortages. Three commercial grades of high melt flow index PP were melt blown at Oak Ridge National Laboratory and broadly characterized by several methods including differential scanning calorimetry (DSC), X-ray diffraction (XRD), and neutron scattering. Despite the apparent similarities (high melt flow and isotacticity) between PP feedstocks, the application of corona charging and charge enhancing additives improve each material to widely varying degrees. From the analysis performed here, the most differentiating factor appears to be related to crystallization of the polymer and the resulting electret formation. Materials with higher crystallization onset temperatures, slower crystallization rates, and larger number of crystallites form a stronger electret and are more effective at filtration.
Novel LDH intercalated with organic aliphatic long-chain anion was large-scale synthesized innovatively by high-energy ball milling in one pot. The linear low density polyethylene (LLDPE)/layered double hydroxides (LDH) composite films with enhanced heat retention, thermal, mechanical, optical and water vapor barrier properties were fabricated by melt blending and blowing process. FT IR, XRD, SEM results show that LDH particles were dispersed uniformly in the LLDPE composite films. Particularly, LLDPE composite film with 1% LDH exhibited the optimal performance among all the composite films with a 60.36% enhancement in the water vapor barrier property and a 45.73 °C increase in the temperature of maximum mass loss rate compared with pure LLDPE film. Furthermore, the improved infrared absorbance (1180–914 cm{sup −1}) of LLDPE/LDH films revealed the significant enhancement of heat retention. Therefore, this study prompts the application of LLDPE/LDH films as agricultural films with superior heat retention. - Graphical abstract: The fabrication process of LLDPE/LDH composite films. - Highlights: • LDH with basal spacing of 4.07 nm was synthesized by high-energy ball milling. • LLDPE composite films with homogeneous LDH dispersion were fabricated. • The properties of LLDPE/LDH composite films were improved. • LLDPE/LDH composite films show superior heat retention property.
The formation of metallic foams by use of a blowing agent in the melt was investigated. It was attempted to produce a metallic foam by melting a mixture of Cu powder and graphite in a SPAR rocket. The graphite combines with the oxide on the copper to form Co and acts as a blowing agent. No foam was formed, and it could not be determined whether the foam fails to form, forms but was lost to surface tension instabilities, or is destroyed by incomplete solidification before reentry.
The melt strength of poly(lactic acid) (PLA) is an important factor in preparing foams and blowing films. Aiming to endow PLA with a suitable melt strength via a slight crosslink, a superficial micro-crosslinking method was introduced in which the PLA feed was mixed with benzoyl peroxide (BPO) and crosslinked in a 100 °C oven for 1 h. Additionally, poly(butyleneadipate-co-terephthalate) (PBAT) was blended with the crosslinked PLA (C-PLA) to further improve melt strength and viscosity. The blend foams were prepared using a single-screw extruder and azodicarbonamide as a foaming agent. The properties were characterized by gel fraction, melt flow rate (MFR), rheometry, DSC and SEM. The rheological results showed that the complex viscosity and storage modulus of C-PLA and C-PLA/PBAT blends increased, attributed to the micro-crosslinking and addition of PBAT and indicating an improvement in melt strength. Furthermore, the crystallization of modified PLA was also enhanced. Compared with pure PLA foams, the C-PLA/PBAT blend foams showed larger cells with more uniform shapes and homogenous distribution. This approach to improve the melt strength of polymers with micro-crosslinking and blending with PBAT represents an attractive method for preparing foams with regular cells.
The Aerospace Industry is experiencing growing demand for high performance polymer foam. The X-33 program needs structural foam insulation capable of retaining its strength over a wide range of environmental conditions. The High Speed Research Program has a need for low density core splice and potting materials. This paper reviews the state of the art in foam materials and describes experimental work to fabricate low density, high shear strength foam which can withstand temperatures from -220 C to 220 C. Commercially available polymer foams exhibit a wide range of physical properties. Some with densities as low as 0.066 g/cc are capable of co-curing at temperatures as high as 182 C. Rohacell foams can be resin transfer molded at temperatures up to 180 C. They have moduli of elasticity of 0.19 MPa, tensile strengths of 3.7 Mpa and compressive strengths of 3.6 MPa. The Rohacell foams cannot withstand liquid hydrogen temperatures, however Imi-Tech markets Solimide (trademark) foams which withstand temperatures from -250 C to 200 C, but they do not have the required structural integrity. The research activity at NASA Langley Research Center focuses on using chemical blowing agents to produce polyimide thermoplastic foams capable of meeting the above performance requirements. The combination of blowing agents that decompose at the minimum melt viscosity temperature together with plasticizers to lower the viscosity has been used to produce foams by both extrusion and oven heating. The foams produced exhibit good environmental stability while maintaining structural properties.
The extensional viscosity is an important rheological characteristic of polymer melts. It is however not as frequently reported on as the shear viscosity. The extensional viscosity is of special interest when considering polymeric materials for foaming and film blowing processes. Here, the extensional (and shear) viscosity along with the melt strength and the tensile properties of the corresponding solid film of a β-glucan concentrate are reported on. A capillary viscometer equipped with a hyperbolic die, yielding a contraction flow, was used to assess the extensional viscosity of the aqueous β-glucan compound at room temperature and at elevated temperatures (110 and 130 °C). In general, the extensional viscosity as well as the shear viscosity decreased with increasing deformation rate. The influence of two different amounts of added water (40 and 50%) was also examined. As expected, both types of viscosities decreased with increasing temperature. It is suggested that gelatinization of the starch fraction in the concentrate at 110 and 130 °C contributes to temperature dependence of the viscosity. To some extent, this is supported by light microscopy and confocal scanning laser microscopy studies of the microstructure of the materials. The results reported here indicate that the β-glucan concentrate might, after some modifications, be used as a complement to fossil-based polymers and processed by conventional manufacturing techniques.
Plastics is a group of materials commonly encountered on a daily basis by many people. They have enabled rapid, low-cost manufacturing of products with complicated geometries and have contributed to the weight reduction of heavy components, especially when produced into a foamed structure. Despite the many advantages of plastics, some drawbacks such as the often fossil-based raw-material and the extensive littering of the material in nature, where it is not degraded for a very long time, needs to be dealt with. One way to address at least one of the issues could be to use polymers from nature instead of fossil-based ones. Here, a β-glucan concentrate originating from barley was investigated. The concentrate was processed into a foam by hot-melt extrusion, and the processing window was established. The effect of different blowing agents was also investigated. Water or a combination of water and sodium bicarbonate were used as blowing agents, the latter apparently giving a more uniform pore structure. The porous structure of the foamed materials was characterized mainly by using a combination of confocal laser scanning microscope and image analysis. The density of the samples was estimated and found to be in a similar range as some polyurethane foams. A set of 3D parameters were also quantified on two selected samples using X-ray microtomography in combination with image analysis, where it was indicated that the porous structure had a pre-determined direction, which followed the direction of the extrusion process.
Here this work demonstrates a greater than expected enhancement of oxygen barrier properties in linear low-density polyethylene (LLDPE)-based materials by blending LLDPE with high-density polyethylene (HDPE). The films made by melt pressing the LLDPE/HDPE blends had a greater reduction in oxygen permeability coefficients (PO 2 ) than predicted using common permeability reduction models, i.e., the harmonic average model and zero-permeability nanofiller model. The reduction of PO 2 was attributed to the presence of spherulite crystal structures, as revealed by atomic force microscopy combined with infrared spectroscopy (AFM-IR). The LLDPE matrix exhibited significant spherulite formation even at a relatively low addition of HDPEs, which likely formed tortuous pathways for diffusing oxygen molecules. Transport results from melt-pressed films contrast with the results from films with similar compositions prepared by film blowing, which did not show barrier enhancement beyond expectation. AFM-IR revealed that the blown films lacked spherulite crystals likely due to stretching in the machine direction followed by rapid cooling. These findings demonstrate the role of processing in controlling microstructures and thus the oxygen barrier performance. This work offers the possibility of achieving easily recyclable LLDPE-based packaging materials by simple blending of polyethylenes with different crystalline content.
Permafrost, permanently frozen ground which underlies much of the Arctic and sub-Arctic, is influenced by deciduous shrubs, yet our understanding of permafrost-shrub interactions is limited. This is largely due to a lack of widespread, long-term, high-quality observations across Arctic and sub-Arctic systems, which are difficult to study due to their remote locations. Shrubs are rapidly expanding in many areas of Arctic tundra and can either amplify or inhibit permafrost thaw, making it crucial that we can understand and predict permafrost-shrub interactions. As we have limited time and resources to make observations, we must design our field campaigns to be as impactful as possible. Below we outline the current state of knowledge and give suggestions about how we can maximize our fieldwork’s impact. From field studies conducted around the Arctic, we know that shrubs generally have a cooling effect on permafrost in the summer, largely caused by the shrub canopy shading the soil. However, summertime cooling can be counteracted by a warming effect in winter, caused by the trapping of blowing snow by shrubs, which leads to increased snow depths. In addition to these commonly observed effects, both observations and models show that other local factors such as climate, soil, snow, and disturbances can interact to cause contrasting dominant effects on permafrost temperatures. For example, shrubs that protrude through the snowpack have been observed to cool permafrost in winter via thermal bridging between the air above the snow and the soil below. However, at other research sites, protruding shrubs lower the surface albedo and cause earlier snowmelt in spring, amplifying permafrost thaw by exposing the soil to thawing earlier. Protruding shrubs have also been observed to induce snow melt in autumn, creating ice layers at the snow surface that prevent further snow accumulation and eliminate the ability of shrubs to trap blowing snow, thereby reducing the winter warming effect. While we understand the physical processes that lead to these effects, we cannot explain why we observe different effects between sites.
The effects of cooling the crystal side surface by blowing a jet of an inert gas are examined in detail for Czochralski crystal growth. A combined model of the crystal + melt, which incorporates the detailed radiation calculations, the shape of the melt-gas meniscus, predicts the growth rate and the crystal-melt interface shape, is used for this study. The convective heat transfer coefficient for the jet is estimated from the correlation available in the literature. The effect of the jet cooling on the interface shape and the pulling rate is significant. The crystal diameter as well as the interface shape tend to be more stable in the environment of the rapid cooling of the crystal by the jet. The crystal diameter or the interface shape can be easily controlled by adjusting the gas flow rate through the jet. This gives the Czochralski pulling an additional degree of freedom facilitating the control of crystal diameter and interface shape.
Traditionally, most flexible food packaging is made of linear low-density polyethylene (LLDPE) which cannot easily be recycled, nor will it degrade in a reasonable timescale. In this work, a biobased biodegradable polyester alternative was investigated as a possible replacement for LLDPE. High molecular weight poly (pentylene adipate-co-terephthalate) with a 40/60 adipic acid/terephthalic acid mole ratio was synthesized using direct esterification and polycondensation. Glycerol and hexane-1,2,5,6-tetrol were added as branching agents to better match the structure of the LLDPE which in turn might help the ability of these materials in film-blowing. Thermal, mechanical, and rheological properties of the copolyesters were thoroughly investigated. All copolyesters had a weight-average molecular weight of over 140,000 g/mol, which is necessary for proper rheology, and were thermally stable up to 350°C. Here, the addition of branching agents led to a slight decrease in crystallinity, d-spacing, melting temperature, enthalpy of melting, stress at break, and elongation at break. However, an increase in Young's modulus and complex viscosity at high frequency were observed compared to PPeAT60 without branching agent added. Although the improved crystallinity and mechanical properties of the copolyesters made them viable for film-blowing, the slow crystallization rate creates a major challenge.
NASA’s Science Mission Directorate (SMD) created the Asteroid Threat Assessment Project (ATAP) to inform decision-makers of risks associated with Potentially Hazardous Objects (PHOs), which may pose an existential threat to human civilization. ATAP assesses risk, in part, by developing analytical physics-based damage models which draw upon data collected during material property characterization efforts, entry simulations, hazard simulations, and ground-based arc-jet testing. Therefore, a pathfinder test campaign was con-ducted at the Hypersonic Materials Environmental Test System (HyMETS) at the NASA Langley Re-search Center to investigate the ablation mechanisms of an ordinary chondrite (Tamdakht H5) and a terrestrial analog (basalt). The HyMETS facility is a 400 kW constricted arc heater used to screen material performance under simulated aerothermal conditions of hypersonic flow.1 Facility conditions were chosen to simulate Earth entry conditions be-tween the upper-mesosphere and the lower thermo-sphere. The ablation mechanisms of Tamdakht and bas-alt are illustrated with still images collected from high-speed video cameras (fig. 1, Tamdakht). Tamdakht produces a relatively stable melt flow, as evidenced by the perpetual growth of a flange at the sidewall and the exiguous detachment of molten material into the flow. Furthermore, an inspection of high-speed video and chemical analysis of the post-test melt layer suggests that the dominant mode of mass loss for Tamdakht, at these test conditions, is expressed through the vaporization of volatiles (e.g., iron, potassium, sodium, phosphorus, and sulfur). The vaporization rates of Tamdakht are greater than basalt under the most extreme test conditions, which leads to an enhanced blowing layer, in-creased thermal shielding, and reduced recession. The ablation mechanisms of basalt are markedly different from Tamdakht and are attributed to the presence of hydrated minerals dispersed at irregular intervals throughout the silicate matrix. Rapid de-composition of secondary minerals and the subsequent formation of water lead to the ejection of the subsurface and overlying melt layer. Furthermore, the presence of water is suspected of lowering the viscosity of the melt layer resulting in increased mass loss near the edge of the test article where drag forces overcome rheological properties (fig. 1, bas-alt). Finally, the results will be discussed in the broader context of meteorite-based material response model development and the potential impact on the Asteroid Threat Assessment Project (ATAP).
Biopolymers are becoming increasingly important to both industry and consumers. With regard to waste management, CO{sub 2} balance and the conservation of petrochemical resources, increasing efforts are being made to replace standard plastics with bio-based polymers. Nowadays biopolymers can be built for example of cellulose, lactic acid, starch, lignin or bio mass. The paper will present material properties of selected cellulose based polymers (cellulose propionate [CP], cellulose acetate butyrate [CAB]) and corresponding processing conditions for particle foams as well as characterization of produced parts. Special focus is given to the raw material properties by analyzing thermal behavior (differential scanning calorimetry), melt strength (Rheotens test) and molecular weight distribution (gel-permeation chromatography). These results will be correlated with the foaming behavior in a continuous extrusion process with physical blowing agents and underwater pelletizer. Process set-up regarding particle foam technology, including extrusion foaming and pre-foaming, will be shown. The characteristics of the resulting foam beads will be analyzed regarding part density, cell morphology and geometry. The molded parts will be tested on thermal conductivity as well as compression behavior (E-modulus, compression strength)