Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials mechanical behaviors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Characterization of High Strain Rate Mechanical behavior of AZ31 magnesium alloy using 3D Digital Image Correlation

Characterization of the material mechanical behavior at sub-Hopkinson regime (0.1 to 1000 s{sup -1}) is very challenging due to instrumentation limitations and the complexity of data analysis involved in dynamic loading. In this study, AZ31 magnesium alloy sheet specimens are tested using a custom designed servo-hydraulic machine in tension at nominal strain rates up to 1000 s{sup -1}. In order to resolve strain measurement artifacts, the specimen displacement is measured using 3D Digital Image correlation instead from actuator motion. The total strain is measured up to {approx} 30%, which is far beyond the measurable range of electric resistance strain gages. Stresses are calculated based on the elastic strains in the tab of a standard dog-bone shaped specimen. Using this technique, the stresses measured for strain rates of 100 s{sup -1} and lower show little or no noise comparing to load cell signals. When the strain rates are higher than 250 s{sup -1}, the noises and oscillations in the stress measurements are significantly decreased from {approx} 250 to 50 MPa. Overall, it is found that there are no significant differences in the elongation, although the material exhibits slight work hardening when the strain rate is increased from 1 to 100 s{sup -1}.

36 MATERIALS SCIENCE↗

2012 THIN FILM AND SMALL SCALE MECHANICAL BEHAVIOR GRS/GRC, JULY 21-27, 2012

The mechanical behavior of materials with small dimension(s) is of both fundamental scientific interest and technological relevance. The size effects and novel properties that arise from changes in deformation mechanism have important implications for modern technologies such as thin films for microelectronics and MEMS devices, thermal and tribological coatings, materials for energy production and advanced batteries, etc. The overarching goal of the 2012 Gordon Research Conference on "Thin Film and Small Scale Mechanical Behavior" is to discuss recent studies and future opportunities regarding elastic, plastic and time-dependent deformation, as well as degradation and failure mechanisms such as fatigue, fracture and wear. Specific topics of interest include, but are not limited to: fundamental studies of physical mechanisms governing small-scale mechanical behavior; advances in test techniques for materials at small length scales, such as nanotribology and high-temperature nanoindentation; in-situ mechanical testing and characterization; nanomechanics of battery materials, such as swelling-induced phenomena and chemomechanical behavior; flexible electronics; mechanical properties of graphene and carbon-based materials; mechanical behavior of small-scale biological structures and biomimetic materials. Both experimental and computational work will be included in the oral and poster presentations at this Conference.

36 MATERIALS SCIENCE↗

The influence of stacking faults on mechanical behavior of advanced materials

We report there are abundant studies on deformation mechanisms in metallic materials dominated by grain boundaries and twin boundaries. In comparison, the influence of stacking faults on deformation mechanisms of materials remains less well understood. Recent studies have shown that when the density of stacking faults increases sharply, their influence on mechanical behavior of metallic or ceramic materials becomes prominent, and in fact, dominates in some cases. This article reviews recent research progress on how nanoscale stacking faults impact the mechanical behavior of metallic and ceramic materials. We primarily focus on studies that reveal the formation of pre-existing stacking faults, their interactions with dislocations, and phase transformations during plastic deformation as evidenced by experiments and simulations. The aim of this review is to highlight the potential opportunities in using stacking faults to tailor the deformation mechanisms of advanced materials.

36 MATERIALS SCIENCE↗

Environmental Testing Of High Temperature Materials and Coatings

Materials for today′s extreme environments have unique challenges and design requirements that require multi-faceted evaluations. Thermal and mechanical testing and analysis is important in design, but environmental effects are often the limiting factor of materials in service. Degradation modes such as oxidation, recession, erosion, foreign object damage, and chemical corrosion can negatively impact the materials thermo-mechanical behavior. While materials may ultimately fail under thermo−mechanical stresses, environmental effects are many times the root cause. Evaluation of materials systems under relevant conditions are critical.....start by identifying mechanisms and develop corresponding test methods. Comprehensive modeling begins with thermo-mechanical behavior, then considers environmental degradation modes that provide a “knock down” of that behavior.

Thermal testing Mechanical testing↗

Reliability Quantification of Advanced Stirling Convertor (ASC) Components

The Advanced Stirling Convertor, is intended to provide power for an unmanned planetary spacecraft and has an operational life requirement of 17 years. Over this 17 year mission, the ASC must provide power with desired performance and efficiency and require no corrective maintenance. Reliability demonstration testing for the ASC was found to be very limited due to schedule and resource constraints. Reliability demonstration must involve the application of analysis, system and component level testing, and simulation models, taken collectively. Therefore, computer simulation with limited test data verification is a viable approach to assess the reliability of ASC components. This approach is based on physics-of-failure mechanisms and involves the relationship among the design variables based on physics, mechanics, material behavior models, interaction of different components and their respective disciplines such as structures, materials, fluid, thermal, mechanical, electrical, etc. In addition, these models are based on the available test data, which can be updated, and analysis refined as more data and information becomes available. The failure mechanisms and causes of failure are included in the analysis, especially in light of the new information, in order to develop guidelines to improve design reliability and better operating controls to reduce the probability of failure. Quantified reliability assessment based on fundamental physical behavior of components and their relationship with other components has demonstrated itself to be a superior technique to conventional reliability approaches based on utilizing failure rates derived from similar equipment or simply expert judgment.

Shah, Ashwin R.↗

Concepts and techniques for ultrasonic evaluation of material mechanical properties

The ultrasonic nondestructive evaluation techniques discussed in the present paper indicate potentials for material characterization and property prediction. Stress wave interaction and material transfer function concepts are examined as a basis for explaining correlations between material mechanical behavior and ultrasonically measured quantities. It is observed that the effect and criticality of any discrete flaw, such as crack, inclusion, or any other stress raiser, is definable only in terms of its material microstructural environment. This underscores the importance of ultrasonic techniques capable of characterizing the stress wave energy transfer properties of a material.

Vary, A.↗

Indentation Methods in Advanced Materials Research Introduction

Since its commercialization early in the 20th century, indentation testing has played a key role in the development of new materials and understanding their mechanical behavior. Progr3ess in the field has relied on a close marriage between research in the mechanical behavior of materials and contact mechanics. The seminal work of Hertz laid the foundations for bringing these two together, with his contributions still widely utilized today in examining elastic behavior and the physics of fracture. Later, the pioneering work of Tabor, as published in his classic text 'The Hardness of Metals', exapdned this understanding to address the complexities of plasticity. Enormous progress in the field has been achieved in the last decade, made possible both by advances in instrumentation, for example, load and depth-sensing indentation and scanning electron microscopy (SEM) and transmission electron microscopy (TEM) based in situ testing, as well as improved modeling capabilities that use computationally intensive techniques such as finite element analysis and molecular dynamics simulation. The purpose of this special focus issue is to present recent state of the art developments in the field.

36 MATERIALS SCIENCE↗

Autonomous reinforcement learning agent for stretchable kirigami design of 2D materials

Abstract Mechanical behavior of 2D materials such as MoS 2 can be tuned by the ancient art of kirigami. Experiments and atomistic simulations show that 2D materials can be stretched more than 50% by strategic insertion of cuts. However, designing kirigami structures with desired mechanical properties is highly sensitive to the pattern and location of kirigami cuts. We use reinforcement learning (RL) to generate a wide range of highly stretchable MoS 2 kirigami structures. The RL agent is trained by a small fraction (1.45%) of molecular dynamics simulation data, randomly sampled from a search space of over 4 million candidates for MoS 2 kirigami structures with 6 cuts. After training, the RL agent not only proposes 6-cut kirigami structures that have stretchability above 45%, but also gains mechanistic insight to propose highly stretchable (above 40%) kirigami structures consisting of 8 and 10 cuts from a search space of billion candidates as zero-shot predictions.

36 MATERIALS SCIENCE↗

The initial buckling behavior of flat and curved fiber metal laminate panels

Local buckling is expected to become an important design issue when metallic materials in conventional stiffened panels are replaced by fiber metal laminates. An experimental study to validate the use of existing design methods for the initial buckling and postbuckling of flat and curved unstiffened fiber metal laminate panels is reported on. All existing design methods can be used for fiber metal laminate panels with the same efficiency and accuracy as for metals. The influence of the collapse behavior and imperfections on the material's mechanical behavior are equal for metallic materials and fiber metal laminate materials. The collapse is found to be important for plates with a curvature parameter of greater than approximately seven, while imperfections are found to play an role for plates with curvature parameters exceeding 20.

Verolme, Koos↗

Mechanical Behavior of Advanced Materials for Aerospace Applications

The purpose of this study was to determine whether High Cycle Fatigue (HCF) loading has any deleterious synergistic effect on life when combined with the typical Low Cycle Fatigue (LCF) loading present in engine disks. This interaction is particularly important in the rim region of blisk applications, where fatigue initiations from vibratory stresses (HCF) may be propagated to the disk by LCF. The primary effort in this study was focused on determining and documenting initiation sites and damage mechanisms. Under LCF loading conditions the failures were predominantly surface initiated, while HCF loading favored internal initiations. Deleterious HCF/LCF interactions would always result in a transition from internal to surface initiations. The results indicated that under the relative stress conditions evaluated there was no interaction between HCF and LCF. In FY99 this effort was extended to investigate several other loading conditions (R-ratio effects) as well as interactions between LCF and two-hour tensile dwells. The results will be published as a NASA Technical Memorandum.

Telesman, Ignancy↗

Mechanical behavior of nanotwinned materials – experimental and computational approaches

Nanotwinned materials exhibit high strength combined with excellent thermal stability, making them potentially attractive for numerous applications. When deposited on cold substrates at high rates, for example, silver films can be prepared with a high-density of growth twins with an average twin boundary spacing of less than 10 nm. These films show a very strong {111} texture, with the twin boundaries being perpendicular to the growth direction. The origins of superior mechanical and thermal properties of nanotwinned materials, however, are not yet fully understood and need further improvements.

36 MATERIALS SCIENCE↗

Development of COPVS for High pressure, In-Space, Cryogenic Fuel Storage

Polymeric composite overwrapped pressure vessels (COPVs) provide an attractive material system to support developing commercial launch business and alternate fuel ventures. However to be able to design with these materials, the mechanical behavior of the materials must be understood with regards to processing, performance, damage tolerance, and environment. For the storage of cryogenic propellants, it is important to evaluate the materials performance and impact damage resistance at cryogenic temperatures in order to minimize weight and to ensure safety and reliability. To evaluate the ultimate performance, various polymeric COPV's have been statically burst tested at cryogenic conditions before and after exposure to irradiation. Materials selected for these COPVs were based on the measured mechanical properties of candidate resin systems and fibers that were also tested at cryogenic conditions before and after exposure to irradiation. The correlation of COPV burst pressures with the constituent material properties has proven to be a valuable screening method for selection of suitable candidate materials with resistance to material degradation due to exposure to temperature and radiation.

DeLay, Tom↗

Nanoscale Mechanical Behavior of Nuclear Materials

One of the primary performance objectives targeted for improved performance of nuclear fuels is fracture toughness. New materials or composite fuel architectures that offer greater resistance to cracking under the extreme environments encountered during nuclear reactor service would provide significant improvements to steady state (e.g. heat transfer, fuel redistribution) and transient (e.g. radionuclide release at elevated temperatures) conditions. Options currently under investigation include 'nontraditional' nuclear fuels designated around high uranium density. These include uranium silicides, uranium borides, and composite fuel materials constructed of these and uranium nitride or uranium dioxide. The increase uranium density compared with uranium dioxide (UO{sub 2}) has made them interesting to a new generation of nuclear fuels research driven by the renewed push for accident-tolerant light water reactor (LWR) fuels. Measurement of the thermophysical and thermodynamic properties of these constituent materials has progressed in recent years, but evaluation of mechanical properties at relevant temperatures is necessary to support further evaluations. While thermophysical properties such as thermal conductivity, heat capacity, and thermal expansion are generally the primary properties of interest, mechanical properties will play an important role in governing the deformation and fracture of the fuel during both normal operation and potential transients. It is therefore necessary to develop techniques capable of measuring these properties to predict the response of a candidate fuel form to anticipated thermal gradients. Nanoindentation techniques provide a demonstrated alternative to traditional mechanical test methods. Much work has also been carried out over the past few years to obtain stress-strain curves using a spherical nanoindentation approach. The techniques are expected to be useful for measurement of the mechanical properties of local structure of various materials. Nanomechanical test techniques have particular value in the area of nuclear materials, where numerous factors motivate limiting the sample volume to the extent possible. However, few attempts at application of nanoindentation to evaluate the mechanical properties of the nuclear fuels and cladding materials are reported in the literature. The effect of a limited set of variables (e.g. porosity, temperature dependence) on the mechanical properties of UO{sub 2} has been explored using early nanomechanical testing techniques. However, nanomechanical evaluation has not been extended to other nuclear fuels. In this work, we demonstrate the effectiveness of using instrumented spherical nanoindentation test techniques to capture the mechanical response of regions within individual grains in ion-irradiated W and Zr over a range of ion-irradiation conditions. As well as the nanomechanical response of U-Si and UO{sub 2} fuel materials Nanoindentation results obtained at room temperature will be used to express nano- and bulk- mechanical properties as a function of material stoichiometry. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fundamental Processes of Coupled Radiation Damage and Mechanical Behavior in Nuclear Fuel Materials for High Temperature Reactors

The objective of this work has been to elucidate the relationship among microstructure, radiation damage and mechanical properties for nuclear fuel materials. As representative nuclear materials, we have taken an hcp metal (Mg as a generic metal, and Ti alloys for fast reactors) and UO2 (representing fuel). The degradation of the thermo-mechanical behavior of nuclear fuels under irradiation, both the fissionable material itself and its cladding, is a longstanding issue of critical importance to the nuclear industry. There are experimental indications that nanocrystalline metals and ceramics may be more resistant to radiation damage than their coarse-grained counterparts. The objective of this project look at the effect of microstructure on radiation damage and mechanical behavior in these materials. The approach to be taken was state-of-the-art, large-scale atomic-level simulation. This systematic simulation program of the effects of irradiation on the structure and mechanical properties of polycrystalline Ti and UO2 identified radiation damage mechanisms. Moreover, it will provided important insights into behavior that can be expected in nanocrystalline microstructures and, by extension, nanocomposites. The fundamental insights from this work can be expected to help in the design microstructures that are less susceptible to radiation damage and thermomechanical degradation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Theoretical studies on the mechanical behavior of granular materials under very low intergranular stresses

The salient aspects of the theoretical modeling of a conventional triaxial test (CTC) of a cohesionless granular medium with stress and strain rate loading are described. Included are a controllable gravitational body force and provision for low confining pressure and/or very low intergranular stress. The modeling includes rational, analytic, and numerical phases, all in various stages of development. The numerical evolutions of theoretical models will be used in final design stages and in the analysis of the experimental data. In this the experimental design stage, it is of special interest to include in the candidate considerations every anomaly found in preliminary terrestrial experimentation. Most of the anomalies will be eliminated by design or enhanced for measurement as the project progresses. The main aspect of design being not the physical apparatus but the type and trajectories of loading elected. The major considerations that have been treated are: appearance and growth of local surface aberrations, stress-power coefficients, strain types, optical strain, radial bead migration, and measures of rotation for the proper stress flux.

French, Kenneth W., Jr.↗

High Performance COPVs for In-Space Storage of High Pressure Cryogenic Fuels

Polymeric composite overwrapped pressure vessels (COPVs) provide an attractive material system to support developing commercial launch business and alternate fuel ventures. However to be able to design with these materials, the mechanical behavior of the materials must be understood with regards to processing, performance, damage tolerance, and environment. For the storage of cryogenic propellants, it is important to evaluate the materials performance and impact damage resistance at cryogenic temperatures in order to minimize weight and to ensure safety and reliability. As part of this study, material tests of candidate fiber and resin systems were used as the basis for the selection of the material combinations for evaluation in a COPV at cryogenic conditions. This comprehensive approach has also been expanded to address issues with impact damage tolerance and material degradation due to environmental factors. KEY WORDS: Cryogenic testing, evaluation and applications for pressure vessels, COPVs, tanks, or storage vessels.

Schneider, Judy↗