Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loss reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Anomalous Loss Reduction Below Two‐Level System Saturation in Aluminum Superconducting Resonators

Superconducting resonators are widely used in many applications such as qubit readout for quantum computing, and kinetic inductance detectors. These resonators are susceptible to numerous loss and noise mechanisms, especially the dissipation due to two-level systems (TLS) which become the dominant source of loss in the few-photon and low temperature regime. In this study, capacitively-coupled aluminum half-wavelength coplanar waveguide resonators are investigated. Surprisingly, the loss of the resonators is observed to decrease with a lowering temperature at low excitation powers and temperatures below the TLS saturation. This behavior is attributed to the reduction of the TLS resonant response bandwidth with decreasing temperature and power to below the detuning between the TLS and the resonant photon frequency in a discrete ensemble of TLS. When response bandwidths of TLS are smaller than their detunings from the resonance, the resonant response and thus the loss is reduced. At higher excitation powers, the loss follows a logarithmic power dependence, consistent with predictions from the generalized tunneling model (GTM). A model combining the discrete TLS ensemble with the GTM is proposed and matches the temperature and power dependence of the measured internal loss of the resonator with reasonable parameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Modeling of RMS Current in CSI Filter Capacitor and Minimum Conduction Loss Operation of CSI-Fed PMSM Drives for Traction Applications

This paper presents a new minimum conduction loss (MCL) torque control algorithm for current source inverter- (CSI-) fed permanent-magnet synchronous machine drives that improves the overall machine drive efficiency by minimizing the combined conduction losses in the inverter and machine at each operating point. First, analytical models of conduction losses in CSI-fed motor drives are presented, and a closed-form expression for optimal d-axis stator current to achieve MCL operation is derived. An expression for the rms current in both wye- and delta-connected CSI output capacitors is derived. A detailed simulation model that emulates the operation of a 100 kW SiC CSI-fed integrated machine drive (IMD) has been developed based on experimental results and finite element analysis. This simulation model is used to evaluate the proposed MCL control algorithm applied to a CSI-fed IMD system for a battery-electric vehicle traction drive, and the predicted total drive system loss with MCL control is compared to predicted losses with maximum-torque-per-ampere (MTPA) and minimum dc-link current (MDCC) control. Results show that MCL control can achieve loss reductions compared to the other two control algorithms over a wide range of operating conditions, with significant loss reductions >20% in the medium-speed regime.

42 ENGINEERING↗

Modeling oxygen reduction activity loss mechanisms in atomically dispersed Fe–N–C electrocatalysts

Materials degradation is a major factor that limits the wider adoption of renewable and clean energy technologies. This is particularly true for the Pt group metal-free (PGM-free) atomically dispersed metal-nitrogen-carbon (M-N-C) catalysts. Here, while many experimental studies have investigated and reported the phenomenological aspects of M-N-C degradation, only a few modeling studies have considered degradation mechanisms at the atomic level. Understanding the mechanisms responsible for activity loss occurring in atomically dispersed M-N-C’s is crucial towards rationally designing active, durable, and less expensive Earth-abundant catalysts. Towards this end, we have surveyed recent literature concerning the modeling of corrosion mechanisms that impact M-N-C catalysts (Fe–N–C, in particular) and offer our own perspectives on the future direction of this field.

36 MATERIALS SCIENCE↗

Learning-Based Quantum Compilation: Translating QASM to QIR with CodeBERT

We propose a learning-based approach to quantum compilation by translating OpenQASM to Quantum Intermediate Representation (QIR) using a fine-tuned CodeBERT model. Trained on 10,000 synthetic QASM-QIR pairs, the model captures code semantics while addressing QIR verbosity and the 512-token limit via a custom token compression scheme. Finetuning was performed on the Frontier supercomputer, with results showing syntactic correctness and stable validation loss reduction. Our method moves toward enabling flexible, language-modeldriven quantum software tools. It also introduces syntax error handling and the possibility of incorporating classical control constructs, addressing limitations in existing rule-based compilers like qBraid-QIR. While the current model has been validated on quantum-only circuits, we propose future evaluations on hybrid quantum-classical examples. This poster will provide architecture insights, compression examples, training loss plots, and QIR outputs. Our work highlights the potential for scalable, adaptable compilation in future quantum toolchains.

Afrose, Sharmin [ORNL]↗

Patterned OLEDs: effect of substrate corrugation pitch and height

Abstract An ongoing OLED challenge is cost-effective enhancement of light extraction, i.e., increasing the external quantum efficiency ( EQE ∼20% in conventional devices). OLEDs on corrugated substrates often show enhanced EQE s providing insight into light emission processes. In particular, patterned plastic substrates directly imprinted easily at room temperature and amenable to low-cost R2R production are ideal for studying/optimizing various structures, further elucidating the extraction process. We show new semi-quantitative data of the effect of the pitch ( a ) and height/depth ( h ) of plastic substrate patterns on the OLEDs’ stack and EQE , focusing on new designs, interestingly, some showing surprisingly enhanced EQE s that were neither reported nor discussed before. These includ e : ( i ) shallow ( h < 200 nm) convex polycarbonate with a ∼ 750 versus ∼400 nm, where the h gradually decreases as the OLED stack is built and ( ii ) concave PET/CAB with large a (∼2.8 and ∼7.8 μ m), where the EQE enhancement of conformal OLEDs may be due largely to scattering. EQE s of green, blue, and white phosphorescent OLEDs were measured. OLEDs on substrates with narrow a ∼ 400 nm and low h < 200 nm s h owed no enhancement, resembling flat devices. In contrast, OLEDs on substrates with comparable or smaller h , but larger a ∼ 750 nm show signific a nt EQE enhancement despite h reduction across the stack. Green OLEDs with a ∼ 750 nm and h ∼ 160 to ∼180 nm, showed EQE s ∼30%, reaching ∼58% with substrate mode extraction. Surprisingly, fully conformal OLEDs on a PET/CAB substrate with a ∼ 7.8 μ m showed blue a nd white EQE s reaching ∼33%, without substrate mode extraction. The enhancing patterns increase the OLEDs’ EQE by reducing surface plasmon excitation and internal waveguiding. The experimental results for OLEDs on substrates with a < 2 μ m are supported by scattering matrix simulations that assume conformal stacks, incorporating diffraction for internal losses reduction. EQE enhancement not predicted by simulations may be due additionally to scattering mostly for substrates with a signific a ntly larger than the emitting wavelength.

42 ENGINEERING↗

Real-time Optimal Dispatch of Behind-the-Meter DERs for Secondary Frequency Regulation

Active distribution networks (ADNs) can provide grid services such as peak load shaving, loss reduction, VoltNar control, congestion management, and frequency regulation. The fast response of inverter-based distributed energy resources (DERs) and battery storage systems enables them to provide ramping support and frequency control. This paper proposes a real-time optimization approach for behind-the-meter DERs to participate in the secondary frequency regulation. The proposed approach determines optimal set-points of output power of DERs to respond to requests from system operators (SOs) in realtime to maintain the frequency of the system at the nominal value. To satisfy the real-time requirement for the secondary frequency control, the nonlinear AC power flow model is linearized considering power losses in the system to achieve both high computational speed and acceptable accuracy. The optimization problem is rerun in a closed loop manner until the mismatch between the requested power by the system operators and actual delivered power at the substation reaches an acceptable tolerance. Furthermore, the proposed approach is validated using modified versions of the IEEE 33-bus and IEEE 69-bus distribution systems. Although the contribution of a single distribution system in the frequency regulation may not be significant, stacked and coordinated contributions from several distribution systems can provide frequency regulation and other grid services at scale.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Environmental and cost benefits of multi‐purpose buffers in an agricultural watershed for biomass production

Abstract The cost‐benefit of riparian buffers to landowners has not been fully understood despite its ecosystem benefits. This study investigates the environmental and economic value of multi‐purpose buffers for biomass production under alternative land‐management scenarios at the watershed scale. The work incorporates the Soil and Water Assessment Tool with a field‐scale tool, the Agriculture Conservation Practice Framework, and cost‐benefit analysis. Our work took place in the agriculturally dominant Raccoon River watershed (RRW) in Iowa. The cost analysis includes implementing and harvesting the switchgrass buffers, the value of nitrogen and phosphorus fertilizer, and the forgone income of cropland to determine the net return under 12 alternative feedstock scenarios. We estimated that 14 603 Mg of nitrogen and 2563 Mg of phosphorus runoffs can be intercepted by riparian buffers in the RRW, representing a nutrient loss reduction of 11% of nitrogen and 26% of phosphorus. These nutrients are valued at $1.31 million (M) for phosphorus and $1.24 M for nitrogen as fertilizers. The trapped nutrients account for 12% of the riparian buffers’ total cost. We found that net economic returns increase with biomass market price, increase with maintenance fertilizer application, and decrease with the cropland areas that are converted to buffers. Under current land management, a biomass market price at $60 per dry ton of biomass would be economically viable at the sub‐basin level when maintenance fertilizers are applied. At $80 per dry ton, all 108 sub‐basins in the RRW would be profitable up to $517 a year. The results highlight the trade‐offs between water quality and profitability. Published 2021. This article is a U.S. Government work and is inthe public domain in the USA. Biofuels, Bioproducts and Biorefining published by Society of Industrial Chemistry and John Wiley & Sons Ltd.

09 BIOMASS FUELS↗

Feasibility of using crystal channeling for the beam loss mitigation in slow extraction at 8GeV

In the accelerator applications of slow extraction for High Energy Physics (HEP), one of the prime challenges is the mitigation of beam losses, which is becoming increasingly critical with the continuous rise in beam power. A significant breakthrough was achieved earlier at CERN through the successful deployment of proton beam channeling in a crystal at 400GeV, effectively diverting the beam away from extraction septa and offering new avenues for improving slow extraction efficiency. However, a crucial question remains whether this approach is still effective at lower and medium proton beam energies. In this paper, we present the promising results of the computer simulation studies of the septum shadowing at 8GeV for the Mu2e project slow extraction at Fermilab. In conclusion, across the wide range of beam parameters, the beam loss reduction is shown to range between 40% and factor of three.

43 PARTICLE ACCELERATORS↗

Additively Manufactured Copper Windings with Hilbert Structure

In this paper, finite element method simulations and frequency analysis of additively manufactured windings with a Hilbert–cross section pattern were performed over a wide frequency range. The current density distributions for the proposed winding conductor and for a square-wire winding conductor at selected frequencies were compared. An approximately 25% winding loss reduction at higher frequencies and an approximately 5% increase at low frequencies were observed for the analyzed Hilbert structure.

Wojda, Rafal↗

Allocating Reserves in Active Distribution Systems for Tertiary Frequency Regulation

This paper proposes a cooperative game theory-based approach for reserve optimization to enable distributed energy resources (DERs) participate in tertiary frequency regulation. Tertiary frequency regulation schemes ensure that reserve requirements of primary and secondary frequency regulation are fulfilled with a minimum cost. While the available reserve from a single distribution system may not suffice tertiary frequency regulation, stacked reserve from several distribution systems can enable them participate in tertiary frequency regulation at scale. In this paper, a two-stage strategy is proposed to effectively and precisely allocate spinning reserve requirement from each DER in distribution systems. In the first stage, two types of characteristic functions are computed: worthiness index (WI) and power loss reduction (PLR). In the second stage, the equivalent Shapley values are computed based on the characteristic functions, which are used to determine distribution factors for reserve allocation among DERs. The effectiveness of the proposed method for allocating reserves among DERs is demonstrated through several case studies on modified versions of the IEEE 13-node and 33-node distribution systems.

Gautam, Mukesh↗

Assessment of Electrode Contamination Mitigation at 0.5 MA Scale

The Z Machine at Sandia National Laboratories uses current pulses with peaks up to 27 MA to drive target implosions and generate high energy density conditions of interest for stockpile stewardship programs pertinent to the NNSA program portfolio . Physical processes in the region near the Z Machine target create electrode plasmas which seed parasitic current loss that reduce the performance and output of a Z experiment. Electrode surface contaminants (hydrogen, water, hydrocarbons) are thought to be the primary constituent of electrode plasmas which contribute to loss mechanisms. The Sandia team explore d in situ heating and plasma discharge techniques by integrating requisite infrastructure into Sandia's Mykonos LTD accelerator, addressing potential impacts to accelerator operation, and reporting on the impact of these techniques on electrode plasma formation and shot performance. The in situ discharge cleaning utilizes the electrodes of the accelerator to excite an argon-oxygen plasma to sputter and chemically react contaminants from electrode surfaces. Insulating breaks are required to isolate the plasma in electrode regions where loss processes are most likely to occur. The shots on Mykonos validate that these breaks do not perturb experiment performance, reducing the uncertainty on the largest unknown about the in situ cleaning system. Preliminary observations with electrical and optical diagnostics suggest that electrode plasma formation is delayed, and overall inventory has been substantively reduced. In situ heating embeds cartridge heaters into accelerator electrodes and employs a thermal bakeout to rapidly desorb contaminants from electrode surfaces. For the first time, additively manufactured (AM) electrode assemblies were used on a low impedance accelerator to integrate cooling channels and manage thermal gradients. Challenges with poor supplier fabrication to specifications, load alignment, thermal expansion and hardware movement and warpage appears to have introduced large variability in observed loss, though, preventing strong assertions of loss reduction via in situ heating. At this time, an in situ discharge cleaning process offers the lowest risk path to reduce electrode contaminant inventories on Z, though we recommend continuing to develop both approaches. Additional engineering and testing are required to improve the implementation of both systems. .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Feasibility of using crystal channeling for the beam loss mitigation in Slow Extraction at 8GeV

The mitigation of the beam losses in slow extraction is becoming more and more demanding in accelerator applications for HEP as the beam power is gradually increasing. The successful demonstration of using the proton beam channeling at 450GeV to deflect the beam away from the extraction septa opens the new levels of improving the slow extraction efficiency. It is yet to be demonstrated that this method is still effective at low and medium proton beam energies. Here we present the promising results of the recent computer simulation studies of the septum shadowing at 8GeV for the Mu2e project slow extraction at Fermilab. Depending on the beam parameters the beam loss reduction is shown to be achievable in the range of 1/3 to factor of 3.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Invertebrate and Plant Community Diversity of an Illinois Corn–Soybean Field with Integrated Shrub Willow Bioenergy Buffers

Perennial bioenergy crop production within intensively managed agricultural landscapes has the potential to improve the sustainability, resiliency, and diversity of these landscapes. Perennial crops are ideal because of their high production potential on marginal lands relative to grain crops (e.g., corn and soybean) and their ability to provide additional ecosystem service benefits. When agricultural landscapes are designed to target specific services, determining the non-targeted services of perennial bioenergy crops can further promote their adoption. This 3-year study addresses this proposition by evaluating the canopy invertebrates and understory plant (non-target crop) communities using bee bowls and point measurement of ground coverage, respectively, within a grain field integrated with shrub willow buffer systems designed for nutrient loss reduction. Greater plant diversity and richness were observed under willow than under grain, resembling that of the surrounding riparian community with more perennial, native species. However, the same relationship did not hold true for invertebrates, with seasonality having a significant influence resulting in similar communities observed in willow and grain plots. The presence of unique plant and invertebrate species in both willow and grain crops as well as foraging pollinators on both crop and non-target crop species highlights the importance of habitat heterogeneity for supporting biodiversity and the potential benefits of buffer bioenergy landscape designs.

09 BIOMASS FUELS↗

A framework and calculator for evaluating the impacts of shelf life extension and other food loss and waste reduction technologies

Optimization of the food supply chain (FSC) depends on reducing food waste, especially at the consumer stage, where a substantial portion of food is not eaten, but instead disposed of via landfill, incineration, or in-sink disposals. One key strategy is to increase the time that consumers have before food goes bad or expires. This study developed a framework to assess the efficacy of shelf-life extension (SLE) technologies for mitigating food loss and waste (FLW), such as packaging improvements. The impact flows through the entire FSC, reducing FLW, energy use, and other inputs at each stage. The framework and resulting calculator can be used to evaluate the impact of FLW reduction at any stage for any food commodity. As shown by two SLE cases, the calculator is valuable for policy-makers, government entities, and professionals, specifically those in marketing, business development, and capital projects teams, to comprehensively evaluate the impacts of FLW reduction technologies and practices. The framework and calculator are sensitive to the shape of the consumption curve, the fraction of inedible waste, and the current shelf life. The calculator was used to assess the impacts of the United States goal of reducing food waste by consumers through various SLE lengths. It was found that uptake of several near-ready-to-deploy SLE technologies would reduce annual food production demand by about 10–19 MMT and supply chain energy consumption by 240–410 PJ in the United States.

Food loss and waste (FLW)↗

Fast ion confinement in the presence of core magnetic islands in Wendelstein 7-X

The effect of magnetic islands in the core region of Wendelstein 7-X (W7-X) on fast ion confinement is explored through simulations with the BEAMS3D code. A magnetic configuration where the n/m = 5/5 island chain is shifted to r/a ~ 0.7 allows the exploration of core island physics in W7-X. The control coil system on W7-X allows the tuning of the island size either increasing the island width or decreasing it. A coupling of the BEAMS3D code to the FIELDLINES code provides a versatile mechanism for incorporating magnetic islands and stochastic regions into the BEAMS3D code. Collisionless simulations suggest that the presence of core islands degrade the confinement of passing particles in the region of the island chain. Full neutral beam simulations of W7-X show a similar behavior with confinement decreasing as the island width is increased. Comparisons between a vacuum magnetic field and low beta HINT2 simulation are made showing similar fast ion behavior. Measurements of lost fast ions in W7-X confirm this trend with the control coil suppressed island configuration showing lower losses than that with no control coils applied. Simulations of fast ion wall loads are performed suggesting no drastic change in loss pattern and a slight reduction in losses with minimized islands.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Medium- and heavy-duty value of technology improvement

Improvements in vehicle technology impact the purchase price of a vehicle and its operating cost. In this study, the monetary benefit of a technology improvement includes the potential reduction in vehicle price from using cheaper or smaller components, as well as the discounted value of the fuel cost savings. As technology progresses over time, the value and benefit of improving technology varies as well. In this study, the value of improving a few selected technologies (battery energy density, electric drive efficiency, tire rolling resistance, aerodynamics, light weighting) is studied and the value of the associated cost saving is quantified. The change in saving as a function of time, powertrain selection and vehicle type is also quantified. For example, a 10% reduction in aerodynamic losses is worth $24,222 today but only $8,810 in 2030 in an electric long haul truck. The decrease in value is primarily due to expected battery cost reduction over time. The same loss reduction in a 2030 conventional long haul truck is worth $5,117 and is primarily driven by a reduction in diesel expenditure. For conventional vehicles, the value of technology improvement is likely to increase over time as diesel price is expected to increase over the next decades while for electric vehicles, the value of technology improvement is likely to decrease as battery energy density increases and cost decreases. The study focuses on medium- and heavy-duty applications where cost of driving is of paramount importance. The savings realized from each technology improvement serve as an upper limit for how much can be spent to acquire that improvement in technology.

Freyermuth, Vincent↗

Influence of contrasting redox conditions on iron (oxyhydr)oxide transformation and associated phosphate sorption

Iron (oxyhydr)oxides strongly adsorb phosphate and limit its bioavailability, but interactions between phosphate and various Fe (oxyhydr)oxides are poorly constrained in natural systems. An in-situ incubation experiment was conducted to explore Fe (oxyhydr)oxide transformation and effects on phosphate sorption in soils with contrasting saturation and redox conditions. Synthetic Fe (oxyhydr)oxides (ferrihydrite, goethite and hematite) were coated onto quartz sand and either pre-sorbed with phosphate or left phosphate-free. The oxide-coated sands were mixed with natural organic matter, enclosed in mesh bags, and buried in and around a vernal pond for up to 12 weeks. Redox conditions were stable and oxic in the upland soils surrounding the vernal pond but largely shifted from Fe reducing to Fe oxidizing in the lowland soils within the vernal pond as it dried during the summer. Iron (oxyhydr)oxides lost more Fe (- 41% ± 10%) and P (- 43 ± 11%) when incubated in the redox-dynamic lowlands compared to the uplands (- 18% ± 5% Fe and - 24 ± 8% P). Averaged across both uplands and lowlands, Fe losses from crystalline goethite and hematite (- 38% ± 6%) were unexpectedly higher than losses from short range ordered ferrihydrite (- 12% ± 10%). We attribute losses of Fe and associated P from goethite and hematite to colloid detachment and dispersion but losses from ferrihydrite to reductive dissolution. Iron losses were partially offset by retention of solubilized Fe as organic-bound Fe(III). Iron (oxyhydr)oxides that persisted during the incubation retained or even gained P, indicating low amounts of phosphate sorption from solution. In conclusion, these results demonstrate that hydrologic variability and Fe (oxyhydr)oxide mineralogy impact Fe mobilization pathways that may regulate phosphate bioavailability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗