Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lithium vapor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Photography of a lithium vapor trail during the daytime.

Barium and lithium vapors were released from sounding rockets in the thermosphere and observed from aboard a jet aircraft at an altitude of 40,000 ft. The purpose of the releases was to demonstrate the feasibility of an all-weather technique for observing chemical releases and to evaluate methods of observing daytime releases. The selected flight plan of the aircraft allowed a series of observations of the trail from two different straight line paths. Data were recorded photographically. The reduction in sky brightness at the 40,000-ft altitude as compared to the ground allows the use of a filter with a 10-A bandwidth for trail photography in the daytime. These photographs verified the calculation of the usable angular field of the narrow-band filters. Photographs of a 45-min-old trail of lithium vapor were obtained up to 20 min after sunrise at the aircraft. It is concluded that now vapor trail observations may be made during the daytime without regard to weather and logistic restrictions.

Bedinger, J. F.↗
NASA NTRS1985

A measurement of the efficiency of lithium vapor production in high altitude releases

The masses of lithium vapor produced in two sounding rocket chemical releases were determined by comparing ground measurements of the irradiance and the brightness distribution of the sunlit releases with the results from a model calculation. The yields of the two releases, which had different compositions, were found to be approximately 5 and 15 percent of the available lithium.

Ledley, B. G.↗
NASA NTRS1973

Observations of chemical releases from high flying aircraft

Barium and lithium vapors were released from sounding rockets in the thermosphere and observed from aboard the NASA Convair 990 at an altitude of 40,000 ft. The purpose of the releases was to (1) check out observational and operational procedures associated with the large high altitude barium release from a Scout rocket (BIC); (2) develop an all-weather technique for observing chemical releases; (3) evaluate methods of observing daytime releases, and (4) investigate the possibilities of observations from a manned satellite. The initial analysis indicates that the previous limitations on the usage of the vapor release method have been removed by the use of the aircraft and innovative photographic techniques. Methods of analysis and applications to the investigation of the thermosphere are discussed.

Bedinger, J. F.↗
NASA NTRS1977

Heat pipe reactors for space power applications

A family of heat pipe reactors design concepts has been developed to provide heat to a variety of electrical conversion systems. Three power plants are described that span the power range 1-500 kWe and operate in the temperature range 1200-1700 K. The reactors are fast, compact, heat-pipe cooled, high-temperature nuclear reactors fueled with fully enriched refractory fuels, UC-ZrC or UO2. Each fuel element is cooled by an axially located molybdenum heat pipe containing either sodium or lithium vapor. Virtues of the reactor designs are the avoidance of single-point failure mechanisms, the relatively high operating temperature, and the expected long lifetimes of the fuel element components.

Koenig, D. R.↗
NASA NTRS1990

The AMPTE lithium releases in the solar wind - A possible trigger for geomagnetic pulsations

Shortly after the AMPTE/IRM satellite had released Lithium ions into the solar wind, magnetometers on the ground and in the frontside magnetosphere observed deflections of a type similar to those associated with solar wind pressure pulses. Since the natural solar wind was very stable during this event and did not exhibit pressure changes, the magnetic deflections have likely been caused by the artificially injected Lithium cloud when it hit the magnetosphere. Order of magnitude estimates show that 300 g of Lithium vapor released in the solar wind are indeed able to produce a 300 nT magnetic deflection on the ground under favorable conditions.

Luehr, Hermann↗
NASA NTRS1993

JPL nuclear electric propulsion task

The development of lithium magnetoplasmadynamic (MPD) thrusters at JPL is discussed. The following topics are presented in vugraph form: mercury vapor mass flow control; porous tungsten vaporizer and housing; the lithium vaporizer experiment; a dry box for handling solid lithium; MPD thruster electrode modeling; engine lifetime definitions; cathode failure modeling; cathode erosion modeling; cathode thermal modeling; near cathode plasma model regions; cathode work function modeling; anode work function modeling; and radiation-cooled anodes.

Pivirotto, Tom↗
NASA NTRS2014

Performance of a Multifunctional Space Evaporator-Absorber-Radiator (SEAR)

The Space Evaporator-Absorber-Radiator (SEAR) is a nonventing thermal control subsystem that combines a Space Water Membrane Evaporator (SWME) with a Lithium Chloride Absorber Radiator (LCAR). The LCAR is a heat pump radiator that absorbs water vapor produced in the SWME. Because of the very low water vapor pressure at equilibrium with lithium chloride solution, the LCAR can absorb water vapor at a temperature considerably higher than the SWME, enabling heat rejection sufficient for most EVA activities by thermal radiation from a relatively small area radiator. Prior SEAR prototypes used a flexible LCAR that was designed to be installed on the outer surface of a portable life support system (PLSS) backpack. This paper describes a SEAR subsystem that incorporates a very compact LCAR. The compact, multifunctional LCAR is built in the form of thin panels that can also serve as the PLSS structural shell. We designed and assembled a 2 ft² prototype LCAR based on this design and measured its performance in thermal vacuum tests when supplied with water vapor by a SWME. These tests validated our models for SEAR performance and showed that there is enough area available on the PLSS backpack shell to enable rejection of metabolic heat from the LCAR. We used results of these tests to assess future performance potential and suggest approaches for integrating the SEAR system with future space suits.

Izenson, Michael G.↗
NASA NTRS2013

Performance of a Multifunctional Space Evaporator- Absorber-Radiator (SEAR)

The Space Evaporator-Absorber-Radiator (SEAR) is a nonventing thermal control subsystem that combines a Space Water Membrane Evaporator (SWME) with a Lithium Chloride Absorber Radiator (LCAR). The LCAR is a heat pump radiator that absorbs water vapor produced in the SWME. Because of the very low water vapor pressure at equilibrium with lithium chloride solution, the LCAR can absorb water vapor at a temperature considerably higher than the SWME, enabling heat rejection by thermal radiation from a relatively small area radiator. Prior SEAR prototypes used a flexible LCAR that was designed to be installed on the outer surface of a portable life support system (PLSS) backpack. This paper describes a SEAR subsystem that incorporates a very compact LCAR. The compact, multifunctional LCAR is built in the form of thin panels that can also serve as the PLSS structural shell. We designed and assembled a 2 sq ft prototype LCAR based on this design and measured its performance in thermal vacuum tests when supplied with water vapor by a SWME. These tests validated our models for SEAR performance and showed that there is enough area available on the PLSS backpack shell to enable heat rejection from the LCAR.

Izenson, Michael G.↗
NASA NTRS1986

Heat pipe cooling for scramjet engines

Liquid metal heat pipe cooling systems have been investigated for the combustor liner and engine inlet leading edges of scramjet engines for a missile application. The combustor liner is cooled by a lithium-TZM molybdenum annular heat pipe, which incorporates a separate lithium reservoir. Heat is initially absorbed by the sensible thermal capacity of the heat pipe and liner, and subsequently by the vaporization and discharge of lithium to the atmosphere. The combustor liner temperature is maintained at 3400 F or less during steady-state cruise. The engine inlet leading edge is fabricated as a sodium-superalloy heat pipe. Cooling is accomplished by radiation of heat from the aft surface of the leading edge to the atmosphere. The leading edge temperature is limited to 1700 F or less. It is concluded that heat pipe cooling is a viable method for limiting scramjet combustor liner and engine inlet temperatures to levels at which structural integrity is greatly enhanced.

Silverstein, Calvin C.↗
NASA NTRS1980

Alkali metal vapors - Laser spectroscopy and applications

The paper examines the rapidly expanding use of lasers for spectroscopic studies of alkali metal vapors. Since the alkali metals (lithium, sodium, potassium, rubidium and cesium) are theoretically simple ('visible hydrogen'), readily ionized, and strongly interacting with laser light, they represent ideal systems for quantitative understanding of microscopic interconversion mechanisms between photon (e.g., solar or laser), chemical, electrical and thermal energy. The possible implications of such understanding for a wide variety of practical applications (sodium lamps, thermionic converters, magnetohydrodynamic devices, new lasers, 'lithium waterfall' inertial confinement fusion reactors, etc.) are also discussed.

Stwalley, W. C.↗
NASA NTRS1972

Fabrication and evaluation of chemically vapor deposited tungsten heat pipe

A network of lithium-filled tungsten heat pipes is considered as a method of heat extraction from high temperature nuclear reactors. The need for material purity and shape versatility in these applications dictates the use of chemically vapor deposited (CVD) tungsten. Adaptability of CVD tungsten to complex heat pipe designs is shown. Deposition and welding techniques are described. Operation of two lithium-filled CVD tungsten heat pipes above 1800 K is discussed.

Bacigalupi, R. J.↗
NASA NTRS1972

Fabrication and evaluation of chemically vapor deposited tungsten heat pipe.

A network of lithium-filled tungsten heat pipes is being considered as a method of heat extraction from high temperature nuclear reactors. The need for material purity and shape versatility in these applications dictates the use of chemically vapor deposited (CVD) tungsten. Adaptability of CVD tungsten to complex heat pipe designs is shown. Deposition and welding techniques are described. Operation of two lithium-filled CVD tungsten heat pipes above 1800 K is discussed.

Bacigalupi, R. J.↗
NASA NTRS2024

Optimization of Mission Enabling Broadband Lyman Ultraviolet Series to Infrared Aluminum Lithium Fluoride Reflectors

The Habitable Worlds Observatory (HWO) concept NASA flagship mission aims extend the ultraviolet (UV) observation range and sensitivity capabilities of the Hubble Space Telescope (HST) with respective goals of reaching photons down to 100 nm and containing an ultraviolet multi-object spectrograph with sensitivity improved 30-100 times. Adding the sensitivity capabilities near the Lyman series spectral range of ~100-121.6 nm reduces the reliance of redshift for key diagnostic ion lines such as O VI (103.2 nm), and heavily ionized gases of Ne VIII (77.5 nm) and MgX (62.5 nm). Clean and unoxidized aluminum (Al) reflectors provide optimal efficiency over a broadband down to the extreme ultraviolet (EUV) wavelength of ~83 nm. To prevent oxidation and maintain high spectral efficiency down to ~100 nm, the Al reflector is conventionally overcoated with a thin lithium fluoride (LiF) layer. We investigate the optimization of the deposition of the Al+LiF coating material composition to attain high spectral efficiency broadband reflectors down to 100 nm and enable the scientific goals of HWO. Lithium hexafluoroaluminate (Li3AlF6) is investigated as a different composition form of LiF to overcoat Al. The spectral efficiency and durability of the reflectors is evaluated. We will demonstrate the use of Li3AlF6 as an overcoat to protect aluminum yields ultra-high efficiency at the Hydrogen Lyman-alpha (HLyα, 121.6 nm) line with experimental reflectance values peaking up to 99%.

optical coatings↗
NASA NTRS1972

Superconductivity in the alkali metal intercalates of molybdenum disulphide

The complete series of alkali metals, lithium through cesium, have been intercalated into molybdenum disulphide, using both the liquid ammonia and vapor techniques. All the intercalates with the exception of lithium yielded full superconducting transitions with onset temperatures of 6 K for AxMoS2(Ax=K,Rb,Cs) and 4 K for BxMoS2(Bx=Li,Na). The superconducting transition for lithium was incomplete down to 1.5 K. Stoichiometries and unit cell parameters have been determined for the intercalation compounds. Both rhombohedral and hexagonal polymorphs of MoS2 have been intercalated and found to exhibit the same superconductivity behavior. The nature of the extraneous superconducting transition of some intercalated samples on exposure to air was elucidated.

Somoano, R. B.↗