Small-scale trapped filaments in intense laser beams.
Small trapped filaments properties in intense laser beams transmitted through various liquids, discussing power and diameters relationships to Kerr effect
Brewer, R. G.↗
SEARCH · Engineering Papers
Results for “laser filamentation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Anti-Stokes generation in trapped filaments of light.
Emission and frequency shift angles of antiStokes radiation from trapped filaments of laser light in liquids
Lifsitz, J. R.↗
Evidence for sinusoidal phase modulation in small self-trapped filaments.
Sinusoidal phase modulation role in spectral broadening observed in trapped filaments of laser and Raman light
Grieneisen, P. H.↗
A new class of trapped light filaments
New class light filament identified in Raman radiation of intense ruby laser beam
RUBY LASER↗
Instruments Sniff Organic Surface Contaminants
Portable instruments detecting both nonvolatile and volatile organic surface contaminants in real time developed. Instruments easy to use: operate under ordinary ambient atmospheric conditions, without need to use messy liquid solvents or install and remove witness plates, and without need to cut specimens from surfaces to be inspected. Principle of detection involves sweeping pure, activated gas across surface spot inspected, then monitoring light emitted at wavelengths characteristic of excited molecules formed by chemical reactions between activated gas and contaminants. Gas activated by dc discharge, radio-frequency induction, microwave radiation, laser beam, hot filaments, or any other suitable means that excites some of gas molecules.
Adler-Golden, Steven↗
Influence of steric effects and compressibility on nonlinear response to laser pulses and the diameters of self-trapped filaments.
Explore the source record for details and available documents.
Gustafson, T. K.↗
Peculiarities of Efficient Plasma Generation in Air and Water by Short Duration Laser Pulses
We have conducted experiments to demonstrate an efficient generation of plasma discharges by focused nanosecond pulsed laser beams in air and provided recommendations on the design of optical systems to implement such plasma generation. We have also demonstrated generation of the secondary plasma discharge using the unused energy from the primary one. Focused nanosecond pulsed laser beams have also been utilized to generate plasma in water where we observed self-focusing and filamentation. Furthermore, we applied the laser generated plasma to the decomposition of methylene blue dye diluted in water.
Plasma↗
Containerless study of metal evaporation by laser induced fluorescence
Laser induced fluorescence (LIF) detection of atomic vapors was used to study evaporation from electromagnetically levitated and CW CO2 laser-heated molybdenum spheres and resistively-heated tungsten filaments. Electromagnetic (EM) levitation in combination with laser heating of tungsten, zirconium, and aluminum specimens was also investigated. LIF intensity vs temperature data were obtained for molybdenum atoms and six electronic states of atomic tungsten, at temperatures up to the melting point of each metal. The detected fraction of the emitted radiation was reduced by self-absorption effects at the higher experimental temperatures. Vaporization enthalpies derived from data for which less than half the LIF intensity was self-absorbed were -636 + or - 24 kJ/g-mol for Mo and 831 + or - 32 kJ/g-mol for W. Space-based applications of EM levitation in combination with radiative heating are discussed.
Schiffman, Robert A.↗
Deep UV Native Fluorescence Imaging of Antarctic Cryptoendolithic Communities
An interdisciplinary team at the Jet Propulsion Laboratory Center for Life Detection has embarked on a project to provide in situ chemical and morphological characterization of Antarctic cryptoendolithic microbial communities. We present here in situ deep ultraviolet (UV) native fluorescence and environmental scanning electron microscopy images transiting 8.5 mm into a sandstone sample from the Antarctic Dry Valleys. The deep ultraviolet imaging system employs 224.3, 248.6, and 325 nm lasers to elicit differential fluorescence and resonance Raman responses from biomolecules and minerals. The 224.3 and 248.6 nm lasers elicit a fluorescence response from the aromatic amino and nucleic acids. Excitation at 325 nm may elicit activity from a variety of biomolecules, but is more likely to elicit mineral fluorescence. The resultant fluorescence images provide in situ chemical and morphological maps of microorganisms and the associated organic matrix. Visible broadband reflectance images provide orientation against the mineral background. Environmental scanning electron micrographs provided detailed morphological information. The technique has made possible the construction of detailed fluorescent maps extending from the surface of an Antarctic sandstone sample to a depth of 8.5 mm. The images detect no evidence of microbial life in the superficial 0.2 mm crustal layer. The black lichen component between 0.3 and 0.5 mm deep absorbs all wavelengths of both laser and broadband illumination. Filamentous deep ultraviolet native fluorescent activity dominates in the white layer between 0.6 mm and 5.0 mm from the surface. These filamentous forms are fungi that continue into the red (iron-rich) region of the sample extending from 5.0 to 8.5 mm. Using differential image subtraction techniques it is possible to identify fungal nuclei. The ultraviolet response is markedly attenuated in this region, apparently from the absorption of ultraviolet light by iron-rich particles coating the filaments. Below 8.5 mm the filamentous morphology of the upper layers gives way to punctate 1-2 micron particles evidencing fluorescent activity following excitation at both deep ultraviolet wavelengths.
Storrie-Lombardi, M. C.↗
AIAA Ascend 2021 Conference On Demand Manufacturing of Electronics Panel Abstract
1. Session Proposal o Session Title NASA’s In Space Manufacturing and the On Demand Manufacturing of Electronics o Session Topic Primary -- Space Logistics, Autonomy, and Robotics; Secondary – Transformative Research and Technologies o Session Format: Panel Discussion. o Requested Session Duration: 60 minutes o Short Session Description: The goal of NASA’s On Demand Manufacturing of Electronics project is to develop and demonstrate the feasibility of a low-gravity, on-demand manufacturing system for flexible hybrid electronic devices on the International Space Station. This panel will feature several key collaborators and team members from the commercial sector, academia, and internal to NASA, each of which are contributing an unique and vital role to the design and implementation of this new technology system. o Extended Session Description (Please describe in detail the activity proposed, including how you intend to use the requested session duration. This session description will be provided to the reviewers for consideration and will not be displayed in the online agenda.): The session will be moderated by Curtis Hill, the Project Lead for the On Demand Manufacturing of Electronics (ODME), and he will start by giving a brief introduction to the ODME project which is working to produce a demo system for the manufacturing of electronic devices on the International Space Station. Panelists consisting of collaborators and team members to the ODME project will then give a brief (~5 min) introduction highlighting their contributions to the project, followed by time for Q&A from the audience. The panel will consist of: 1. Kenneth Church, nScrypt. nScrypt is a leader in multi-material printing with a modular system that incorporates a direct write thick film print head, a polymer fused filament fabrication print head, a laser sintering attachment, a drill head attachment for milling, and a pick and place. The system can print a layer and scan for accuracy of prints. The combination of multiple print heads and scanning allows for the on-demand production of intricate electronic components. 2. Andy Kurk, TechShot, Inc. Techshot, Inc. has collaborated extensively with NASA on the in space manufacturing of both printed electronics and fused metal materials. They are currently working to develop and integrate a test system for printed electronics, and a flight demonstration on the International Space Station is anticipated in 2024. 3. Ed Hendricks, NextFlex. NextFlex has the goal of advancing the manufacture of flexible hybrid electronics in the U.S. They are working with ODME on the development of AstroSense, an additively manufactured, wireless, flexible, and wearable health sensor. 4. Dr. Pradeep Lall, Auburn University. Professor Lall is the MacFarlane Endowed Distinguished Professor in the Department of Mechanical Engineering with a Courtesy Joint Appointment in the Department of Electrical and Computer Engineering and a Courtesy Joint Appointment in the Department of Finance. He is collaborating with NASA’s ODME project to develop multilayer printable devices and to develop techniques to test the quality of a printed electronic device. 5. Dr. Wei Gao, California Institute of Technology. Professor Gao is an Assistant Professor of Medical Engineering. His group is developing fully printed, flexible, and wearable biosensors for crew health monitoring in collaboration with NASA’s ODME project. In addition, they are working on using sweat to power biofuel cells for wearable, self-powered electronic devices. 6. Beth Paquette, NASA Goddard. The ODME branch at NASA Goddard is spearheading a sounding rocket flight demo to prove the capability of a printed electronic device with multiple sensors. In addition, they focus on thin film and flexible energy storage evaluations. o Session Goal(s)/Outcome(s): Please list the learning objectives and/or tangible outcomes (technical paper or other publication). The goal of this session is to highlight the internal and collaborative efforts of NASA’s On Demand Manufacturing of Electronics project to develop a system for printing electronics that will be tested on the International Space Station in 2024. In addition, the session with facilitate discussion with the community on the state of the art of printable electronics, current challenges, and new avenues for collaboration.
Jennifer McInnis Jones↗
Microelectromechanical Systems (MEMS) Broadband Light Source Developed
A miniature, low-power broadband light source has been developed for aerospace applications, including calibrating spectrometers and powering miniature optical sensors. The initial motivation for this research was based on flight tests of a Fabry-Perot fiberoptic temperature sensor system used to detect aircraft engine exhaust gas temperature. Although the feasibility of the sensor system was proven, the commercial light source optically powering the device was identified as a critical component requiring improvement. Problems with the light source included a long stabilization time (approximately 1 hr), a large amount of heat generation, and a large input electrical power (6.5 W). Thus, we developed a new light source to enable the use of broadband optical sensors in aerospace applications. Semiconductor chip-based light sources, such as lasers and light-emitting diodes, have a relatively narrow range of emission wavelengths in comparison to incandescent sources. Incandescent light sources emit broadband radiation from visible to infrared wavelengths; the intensity at each wavelength is determined by the filament temperature and the materials chosen for the filament and the lamp window. However, present commercial incandescent light sources are large in size and inefficient, requiring several watts of electrical power to obtain the desired optical power, and they emit a large percentage of the input power as heat that must be dissipated. The miniature light source, developed jointly by the NASA Glenn Research Center, the Jet Propulsion Laboratory, and the Lighting Innovations Institute, requires one-fifth the electrical input power of some commercial light sources, while providing similar output light power that is easily coupled to an optical fiber. Furthermore, it is small, rugged, and lightweight. Microfabrication technology was used to reduce the size, weight, power consumption, and potential cost-parameters critical to future aerospace applications. This chip-based light source has the potential for monolithic fabrication with on-chip drive electronics. Other uses for these light sources are in systems for vehicle navigation, remote sensing applications such as monitoring bridges for stress, calibration sources for spectrometers, light sources for space sensors, display lighting, addressable arrays, and industrial plant monitoring. Two methods for filament fabrication are being developed: wet-chemical etching and laser ablation. Both yield a 25-mm-thick tungsten spiral filament. The proof-of-concept filament shown was fabricated with the wet etch method. Then it was tested by heating it in a vacuum chamber using about 1.25 W of electrical power; it generated bright, blackbody radiation at approximately 2650 K. The filament was packaged in Glenn's clean-room facilities. This design uses three chips vacuum-sealed with glass tape. The bottom chip consists of a reflective film deposited on silicon, the middle chip contains a tungsten filament bonded to silicon, and the top layer is a transparent window. Lifetime testing on the package will begin shortly. The emitted optical power is expected to be approximately 1.0 W with the spectral peak at 1.1 mm.
Tuma, Margaret L.↗
Technology Roadmap for the Development of an Orbital Smallsat Factory
Explore the source record for details and available documents.
small sat↗
Noncontact acousto-ultrasonics using laser generation and laser interferometric detection
A compact, portable fiber-optic heterodyne interferometer designed to detect out-of-plane motion on surfaces is described. The interferometer provides a linear output for displacements over a broad frequency range and can be used for ultrasonic, acoustic emission, and acousto-ultrasonic (AU) testing. The interferometer in conjunction with a compact pulsed Nd:YAG laser represents a noncontact testing system. This system was tested to determine its usefulness for the AU technique. The results obtained show that replacement of conventional piezoelectric transducers (PZT) with a laser generation/detection system make it possible to carry out noncontact AU measurements. The waveforms recorded were 5 MHZ PZT-generated ultrasound propagating through an aluminum block, detection of the acoustic emission event, and laser AU waveforms from graphite-epoxy laminates and a filament-wound composite.
Green, Robert E., Jr.↗
Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing
NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.
sintering, alloys, 3D printing↗
Containerless high temperature property measurements by atomic fluorescence
Laser induced fluorescence techniques were developed for the containerless study of high temperature processes, material properties, levitation, and heating techniques for containerless earth-based experimentation. Experiments were performed in which fluorescence of atomic aluminum, mercury, or tungsten were studied. These experiments include measurements of: (1) Al atom evaporation from CW CO2 laser heated and aerodynamically levitated sapphire and alumina spheres, and self-supported sapphire filaments, (2) Al atom reaction with ambient oxygen in the wake of a levitated specimen, (3) Hg atom concentrations in the wake of levitated alumina and sapphire spheres, relative to the ambient Hg atom concentration, (4) Hg atom concentrations in supersonic levitation jets, and (5) metastable, electronically excited W atom concentrations produced by evaporation of an electrically heated tungsten filament.
Nordine, P. C.↗
Laser Ablation Increases PEM/Catalyst Interfacial Area
An investigational method of improving the performance of a fuel cell that contains a polymer-electrolyte membrane (PEM) is based on the concept of roughening the surface of the PEM, prior to deposition of a thin layer of catalyst, in order to increase the PEM/catalyst interfacial area and thereby increase the degree of utilization of the catalyst. The roughening is done by means of laser ablation under carefully controlled conditions. Next, the roughened membrane surface is coated with the thin layer of catalyst (which is typically platinum), then sandwiched between two electrode/catalyst structures to form a membrane/ele c t - rode assembly. The feasibility of the roughening technique was demonstrated in experiments in which proton-conducting membranes made of a perfluorosulfonic acid-based hydrophilic, protonconducting polymer were ablated by use of femtosecond laser pulses. It was found that when proper combinations of the pulse intensity, pulse-repetition rate, and number of repetitions was chosen, the initially flat, smooth membrane surfaces became roughened to such an extent as to be converted to networks of nodules interconnected by filaments (see Figure 1). In further experiments, electrochemical impedance spectroscopy (EIS) was performed on a pristine (smooth) membrane and on two laser-roughened membranes after the membranes were coated with platinum on both sides. Some preliminary EIS data were interpreted as showing that notwithstanding the potential for laser-induced damage, the bulk conductivities of the membranes were not diminished in the roughening process. Other preliminary EIS data (see Figure 2) were interpreted as signifying that the surface areas of the laser-roughened membranes were significantly greater than those of the smooth membrane. Moreover, elemental analyses showed that the sulfur-containing molecular groups necessary for proton conduction remained intact, even near the laser-roughened surfaces. These preliminary results can be taken as indications that laser-roughened PEMs should function well in fuel cells and, in particular, should exhibit current and power densities greater than those attainable by use of smooth membranes.
Whitacre, Jay↗
Laser-induced electric breakdown in solids
A review is given of recent experimental results on laser-induced electric breakdown in transparent optical solid materials. A fundamental breakdown threshold exists characteristic for each material. The threshold is determined by the same physical process as dc breakdown, namely, avalanche ionization. The dependence of the threshold on laser pulse duration and frequency is consistent with this process. The implication of this breakdown mechanism for laser bulk and surface damage to optical components is discussed. It also determines physical properties of self-focused filaments.
Bloembergen, N.↗
A study of transient stimulated Raman scattering and self-focusing in the picosecond time regime
Two third order processes, stimulated Raman scattering and self-focusing, with picosecond pulses are studied. In the case of transient stimulated scattering, the gain is reduced from the steady state value, and qualitatively new features, such as shortening and delay of the Stokes pulse relative to the laser pulse, appear. These predictions are extended to realistic laser pulses, and experiments confirm all of the theoretical predictions. The self-focusing and frequency broadening of picosecond pulses is studied in the absence of stimulated Raman scattering in several materials with large orientational Kerr constants. Measurements of the relaxation time indicate that the orientational Kerr effect is important in the self-focusing of picosecond pulses. Self-focused filaments are observed to propagate with constant diameters over a distance greater than 10 cm, but disappear before the end of a 20 cm cell. The filaments radiate light continuously along their path and the spectrum of the light shows that the frequency content extends symmetrically for several hundred wave numbers on either side of the laser frequency.
Reintjes, J. F.↗