The Wind-induced Loads on a Dynamically Scaled Model of a Large Missile in Launching Position
Wind tunnel tests - effect of wind induced loads on dynamically scaled model of large missile in launching position
WIND EFFECT↗
SEARCH · Engineering Papers
Results for “large load modeling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Aerodynamic loads measurements on externally blown flap STOL models
Small-scale-model data have shown large static loads on the flap system behind the engines. The large-scale-model tests confirmed the magnitude of these loads and indicated that the relative loading of each flap element depends on the engine-wing-flap geometry. Flap response measurements indicated that the unsteady pressure loading excited the natural vibration modes of the flap system on this model. Since this was a boilerplate model, the only conclusion that can be drawn is that the possibility of large vibration loads must be considered for a flight-weight structure. The similarity of the unsteady pressure and flap response spectra for the wind-off and wind-on cases indicated that it may be possible to realistically test flight-weight flap structures on a static test stand rather than endure the extra costs and scheduling problems associated with large-scale wind-tunnel tests. There is a potential flap-temperature problem which if not resolved might preclude the use of materials such as aluminum and the composites in the flap structure.
Greene, G. C.↗
AERODYNAMIC CHARACTERISTICS IN GROUND EFFECT OF A LARGE-SCALE MODEL WITH A HIGH DISK-LOADING LIFTING FAN MOUNTED IN THE FUSELAGE
Aerodynamic characteristics in ground effect of a large scale model
AERODYNAMIC CHARACTERISTICS↗
Measured and calculated steady aerodynamic loads on a large-scale upper-surface blown model
Static aerodynamic loads measurements from wind tunnel tests of a full-scale upper surface blown jet flap configuration are presented. The measured loads are compared with calculations using a method for predicting longitudinal aerodynamic characteristics of upper surface blown jet flap configurations.
Perry, B., III↗
Aerodynamic Characteristics of a Large-Scale Model with a High Disk-Loading Lifting Fan Mounted in the Fuselage
An investigation was conducted to determine the longitudinal characteristics during low-speed flight of a large-scale VTOL airplane model with a direct lifting fan enclosed in the fuselage. The model had a shoulder-mounted unswept wing of aspect ratio 5. The effect on longitudinal characteristics of fan operation, propulsion by means of deflecting the fan efflux, trailing-edge flap deflection, and horizontal-tail height were studied.
Aoyagi, Kiyoshi↗
Aerodynamic heating and loading within large open cavities in cone and cone-cylinder-flare models at Mach 6.7
The aerodynamic heating and loading distributions within large cavities exposed by surface openings to hypersonic flow were determined in the 8-foot high-temperature structures tunnel. Cone and cone-cylinder-flare models with cavities having regular and irregular surface-opening shapes were aerothermally tested at various angles of attack up to 30 deg. Tests were conducted at a Mach number of 6.7, a total temperature of 1800 K, a dynamic pressure of 80 kPa, and a stream unit Reynolds number of 6,000,000 per meter. The results showed that the heating rates at internal reattachment were generally lower but of the same order as the corresponding external heating rates; however, other internal heating rates were an order of magnitude lower. The internal flow showed characteristics of being funneled into jets or being dispersed dependent upon the internal surface contour.
Hunt, R. L.↗
WING AND FLAP LOADS OBTAINED FROM A WIND-TUNNEL INVESTIGATION OF LARGE-SCALE V STOL MODEL
Wing and flap loads of v/stol aircraft - wind tunnel study
WING LOADING↗
Scaling effects in the static and dynamic response of graphite-epoxy beam-columns
Scale model technology represents one method of investigating the behavior of advanced, weight-efficient composite structures under a variety of loading conditions. It is necessary, however, to understand the limitations involved in testing scale model structures before the technique can be fully utilized. These limitations, or scaling effects, are characterized. in the large deflection response and failure of composite beams. Scale model beams were loaded with an eccentric axial compressive load designed to produce large bending deflections and global failure. A dimensional analysis was performed on the composite beam-column loading configuration to determine a model law governing the system response. An experimental program was developed to validate the model law under both static and dynamic loading conditions. Laminate stacking sequences including unidirectional, angle ply, cross ply, and quasi-isotropic were tested to examine a diversity of composite response and failure modes. The model beams were loaded under scaled test conditions until catastrophic failure. A large deflection beam solution was developed to compare with the static experimental results and to analyze beam failure. Also, the finite element code DYCAST (DYnamic Crash Analysis of STructure) was used to model both the static and impulsive beam response. Static test results indicate that the unidirectional and cross ply beam responses scale as predicted by the model law, even under severe deformations. In general, failure modes were consistent between scale models within a laminate family; however, a significant scale effect was observed in strength. The scale effect in strength which was evident in the static tests was also observed in the dynamic tests. Scaling of load and strain time histories between the scale model beams and the prototypes was excellent for the unidirectional beams, but inconsistent results were obtained for the angle ply, cross ply, and quasi-isotropic beams. Results show that valuable information can be obtained from testing on scale model composite structures, especially in the linear elastic response region. However, due to scaling effects in the strength behavior of composite laminates, caution must be used in extrapolating data taken from a scale model test when that test involves failure of the structure.
Jackson, Karen E.↗
Simulation of flight test conditions in the Langley pilot transonic cryogenic tunnel
The theory and advantages of the cryogenic tunnel concept are briefly reviewed. The unique ability to vary temperature independently of pressure and Mach number allows, in addition to large reductions in model loads and tunnel power, the independent determination of Reynolds number, Mach number, and aeroelastic effects on the aerodynamic characteristics of the model. Various combinations of Reynolds number and dynamic pressure are established to represent accurately flight variations of aeroelastic deformation with altitude changes. The consequences of the thermal and caloric imperfections of the test gas under cryogenic conditions were examined and found to be insignificant for operating pressures up to 5 atm. The characteristics of the Langley pilot transonic cryogenic tunnel are described and the results of initial tunnel operation are presented. Tests of a two-dimensional airfoil at a Mach number of 0.85 show identical pressure distributions for a chord Reynolds number of 8,600,000 obtained first at a stagnation pressure of 4.91 atm at a stagnation temperature of 322.0 K and then at a stagnation pressure of 1.19 atm at a stagnation temperature of 116.5 K.
Kilgore, R. A.↗
Wind tunnel investigation of aerodynamic loads on a large-scale externally blown flap model and comparison with theory
Results from a wind-tunnel investigation of a large-scale externally blown flap model are presented. The model was equipped with four turbofan engines, a triple-slotted flap system, and a T-tail. The wing had a quarter-chord sweep of 25 deg, an aspect ratio of 7.28, and a taper ratio of 0.4. Aerodynamic loads and load distributions were determined from a total of 564 static pressure orifices located on the upper and lower surfaces of the slat, wing, and flaps. Loads are presented for variations of angle of attack, engine thrust setting, and flap deflection angle. In addition, the experimental results are compared with analytical results calculated by using a potential flow analysis.
Perry, B., III↗
Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading
Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.
Kelkar, A.↗
Progressive Failure Analysis Correlation with Notched Composite Laminate Test Data
Testing of small and intermediate laminate panels with notches was performed and Progressive Failure Analyses (PFA) models were developed for aid in test planning and for correlation with the test data. Two progressive damage failure models were included in the study: the commercially available Abaqus built-in damage model and COmplete STress Reduction (COSTR) damage model developed at NASA Langley Research Center (LaRC). The finite elements models used for the analysis were developed using shell elements. The pre-test PFA results obtained from the two damage models were compared to test data. Then a post-test PFA with updated material properties based on additional available material property data was executed with the COSTR damage model and compared to the test data. The panels tested in compression all exhibited less scatter in the failure load with self-similar failure behavior. The panels tested in tension exhibited more scatter in the failure load with a failure mode that included delamination of plies. However, a self-similar crack path was also observed as the overall failure mode for all panels tested. When comparing test data to the pre-test analysis results, both damage models with shell element models were considered adequate for predicting the behavior and failure load of both the small and intermediate panels when tested in compression. However, for the tension load cases, larger differences were observed between the test and analysis results. When comparing test data to the post-test analysis performed using the COSTR damage model, better correlation was observed. However, large discrepancies were still observed for the tension load cases. Consequently, a higher fidelity finite element model including solid elements for sub-laminates and the modeling of cohesive layers between sub-laminate layers is recommended for tension loading of notched composite laminates.
Damage Model,Progressive Failure Analysis,Open Hol↗
Load Diffusion in Composite and Smart Structures
The research carried out here builds on our previous NASA supported research on the general topic of edge effects and load diffusion in composite structures. Further fundamental solid mechanics studies were carried out to provide a basis for assessing the complicated modeling necessary for the multi-functional large scale structures used by NASA. An understanding of the fundamental mechanisms of load diffusion in composite subcomponents is essential in developing primary composite structures. Some specific problems recently considered were those of end effects in smart materials and structures, study of the stress response of pressurized linear piezoelectric cylinders for both static and steady rotating configurations, an analysis of the effect of pre-stressing and pre-polarization on the decay of end effects in piezoelectric solids and investigation of constitutive models for hardening rubber-like materials. Our goal in the study of load diffusion is the development of readily applicable results for the decay lengths in terms of non-dimensional material and geometric parameters. Analytical models of load diffusion behavior are extremely valuable in building an intuitive base for developing refined modeling strategies and assessing results from finite element analyses. The decay behavior of stresses and other field quantities provides a significant aid towards this process. The analysis is also amenable to parameter study with a large parameter space and should be useful in structural tailoring studies. Special purpose analytical models of load diffusion behavior are extremely valuable in building an intuitive base for developing refined modeling strategies and in assessing results from general purpose finite element analyses. For example, a rational basis is needed in choosing where to use three-dimensional to two-dimensional transition finite elements in analyzing stiffened plates and shells. The decay behavior of stresses and other field quantities furnished by this research provides a significant aid towards this element transition issue. A priori knowledge of the extent of boundary-layers induced by edge effects is also useful in determination of the instrumentation location in structural verification tests or in material characterization tests.
Horgan, C. O.↗
Structural dynamics system model reduction
Loads analysis for structural dynamic systems is usually performed by finite element models. Because of the complexity of the structural system, the model contains large number of degree-of-freedom. The large model is necessary since details of the stress, loads and responses due to mission environments are computed. However, a simplified model is needed for other tasks such as pre-test analysis for modal testing, and control-structural interaction studies. A systematic method of model reduction for modal test analysis is presented. Perhaps it will be of some help in developing a simplified model for the control studies.
Chen, J. C.↗
A kinematically driven anisotropic viscoelastic constitutive model applied to tires
Aircraft tires are composite structures manufactured with viscoelastic materials such as carbon black filled rubber and nylon cords. When loaded they experience large deflections and moderately large strains. Detailed structural models of tires require the use of either nonlinear shell or nonlinear three dimensional solid finite elements. Computational predictions of the dynamic response of tires must consider the composite viscoelastic material behavior in a realistic fashion. We describe a modification to a nonlinear anisotropic shell finite element so it can be used to model viscoelastic stresses during general deformations. The model is developed by introducing internal variables of the type used to model elastic strain energy. The internal variables are strains, curvatures, and transverse shear angles which are in a one-to-one correspondence with the generalized coordinates used to model the elastic strain energy for nonlinear response. A difference-relaxation equation is used to relate changes in the observable strain field to changes in the internal strain field. The internal stress state is introduced into the equilibrium equations by converting it to nodal loads associated with the element's displacement degrees of freedom. In this form the tangent matrix in the Newton-Raphson solution algorithm is not modified from its form for the nonlinear statics problem. Only the gradient vector is modified and the modification is not computationally costly. The existing finite element model for the Space Shuttle nose gear tire is used to provide examples of the algorithm. In the first example, the tire's rim is displaced at a constant rate up to a fixed value. In the second example, the tire's rim is enforced to follow a saw tooth load and unload curve to generate hysteresis loops.
Johnson, Arthur R.↗
Evaluation of an aerodynamic-load prediction method on a STOL fighter configuration
A three-dimensional panel method was used to compute the aerodynamic loads on a large-scale, powered wind tunnel model. The size of the computation grid was selected such that turnaround times, on present computers remained satisfactory. With this constraint, the STOL aircraft configuration was modeled and the capabilities and limitations of the prediction method were investigated. After this study, a similar numerical model was established for a forward-swept-wing aircraft configuration which is planned for large-scale, low-speed testing. The resulting aerodynamic-load predictions are discussed and will be utilized, together with the future experimental results, to obtain a broader validation of this method as well as to reduce the necessary size of the matrix of the test parameters.
Katz, J.↗
Evaluation of an aerodynamic-load prediction method on a STOL fighter configuration
A three-dimensional panel method was used to compute the aerodynamic loads on a large-scale, powered wind tunnel model. The size of the computation grid was selected such that turnaround times, on present computers remained satisfactory. With this constraint, the STOL aircraft configuration was modeled and the capabilities and limitations of the prediction method were investigated. After this study, a similar numerical model was established for a forward-swept-wing aircraft configuration which is planned for large-scale, low-speed testing. The resulting aerodynamic-load predictions are discussed and will be utilized, together with the future experimental results, to obtain a broader validation of this method as well as to reduce the necessary size of the matrix of the test parameters.
Katz, J.↗
Analysis of a thin-walled pressurized torus in contact with a plane
Finite element analysis is applied to study the large deflection of a standing torus loaded by a plane. The internally pressurized thin-walled structure is found to have an elliptical footprint area. Considerable bulge occurs in the sidewall in the region of the load plane. Stress distributions throughout the torus are shown for various load levels and for various modeling strategies at a given load level. In large load ranges finite element calculations show compressive circumferential stress and negative curvature in the footprint region. Results are compared with inelastic wall analysis.
Mack, M. J., Jr.↗