Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large amplitude oscillatory shear”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Understanding the transient large amplitude oscillatory shear behavior of yield stress fluids

A full understanding of the sequence of processes exhibited by yield stress fluids under large amplitude oscillatory shearing is developed using multiple experimental and analytical approaches. A novel component rate Lissajous curve, where the rates at which strain is acquired unrecoverably and recoverably are plotted against each other, is introduced and its utility is demonstrated by application to the analytical responses of four simple viscoelastic models. Using the component rate space, yielding and unyielding are identified by changes in the way strain is acquired, from recoverably to unrecoverably and back again. The behaviors are investigated by comparing the experimental results with predictions from the elastic Bingham model that is constructed using the Oldroyd–Prager formalism and the recently proposed continuous model by Kamani, Donley, and Rogers in which yielding is enhanced by rapid acquisition of elastic strain. The physical interpretation gained from the transient large amplitude oscillatory shear (LAOS) data is compared to the results from the analytical sequence of physical processes framework and a novel time-resolved Pipkin space. The component rate figures, therefore, provide an independent test of the interpretations of the sequence of physical processes analysis that can also be applied to other LAOS analysis frameworks. Each of these methods, the component rates, the sequence of physical processes analysis, and the time-resolved Pipkin diagrams, unambigiously identifies the same material physics, showing that yield stress fluids go through a sequence of physical processes that includes elastic deformation, gradual yielding, plastic flow, and gradual unyielding.

Kamani, Krutarth M. (ORCID:0000000338975420)↗
DOE OSTI2024

Methodology to determine printability criteria of highly concentrated pastes through rheological characterization

Material extrusion is an additive manufacturing technique that enables the creation of reproducible and complex hardware by depositing a viscous, shear-thinning ink onto a substrate in a custom-pattern via extrusion through a syringe. Here, the ability of an ink to be extruded onto a substrate in many layers, and maintain the desired shape is what defines the printability. Printability is often investigated by formulating, printing, and postmortem analysis of final parts in an iterative manner. Investigations of printability through rheological characterization have often been concerned with inks that straddle the line between printable and too thin, leaving out an entire class of inks that are highly-filled pastes, where extrudability is the limiting factor. Highly-filled pastes continue to pose issues for researchers as the effect of filler morphology, size, loading, and packing fraction on the ink rheology and corresponding printability is not understood. While traditional rheological characterizations may be useful for some inks, we show that protocols utilizing steady-shear, or large-amplitude oscillatory shear are difficult and unreliable for highly-filled pastes. Through transient rheology paired with real-time images we show that each traditional protocol produces inhomogeneous deformations that violate the assumptions that underly common rheological definitions. Instead, we demonstrate metrics measured with small-amplitude oscillatory shear that are correlated to the printability of various ink formulations ranging in loading. The rheological measures that accurately predict the printability of the inks are the axial stress measured at small amplitudes, and the critical stress amplitude above which rheological characterizations become impossible. In addition, we estimate the maximum packing fraction for each filler, based on the exponent common to hard sphere models, and show that the printability of each ink can be predicted by the ratio of the packing fraction to the theoretical maximum. We show how small-amplitude oscillatory shear allows users to develop printability criteria for any ink to enhance the workflow in the development of new inks, increase the performance of material extrusion printing, and improve the stability of printed parts, with less wasted time and materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Easy-Processable and Aging-Free All-Polymer Polysiloxane Composites

In this work, we report all-polymer polysiloxane composites that overcome the long-standing processing problems of silica-reinforced silicone rubbers. Polystyrene fillers are dispersed with styrene/dimethylsiloxane symmetric diblock and triblock copolymers that control the filler morphology, filler–matrix interactions, and filler–filler interactions. Surprisingly, the composites not only rival the traditional silica-reinforced polysiloxane in mechanical properties of cured materials but also have better processability and stability than the silica-filled compound before curing. Large amplitude oscillatory shear experiments demonstrate that the triblock copolymer addition strongly affects the rheological properties. We hypothesize that the bridges and entangled loops that were formed by the triblock copolymer can connect different PS domains to provide additional reinforcement. The aging effect that originates from PDMS chain adsorption on the filler particle surface is also avoided because of the thermodynamic repulsion between PS and PDMS phases.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effects of Salt on Phase Behavior and Rheological Properties of Alginate–Chitosan Polyelectrolyte Complexes

Oppositely charged polyelectrolytes often form polyelectrolyte complexes (PECs) due to the association through electrostatic interactions. Obtaining PECs using natural, biocompatible polyelectrolytes is of interest in the food, pharmaceutical, and biomedical industries. In this work, PECs were prepared from two biopolymers, positively charged chitosan and negatively charged alginate. We investigate the changes in the structure and properties of PECs by adding sodium chloride (salt doping) to the system. The shear modulus of PECs can be tuned from ~10 to 10 4 Pa by changing the salt concentration. The addition of salt led to a decrease in the water content of the complex phase with increasing shear modulus. However, at a very high salt concentration, the shear modulus of the complex phase decreased but did not lead to the liquid coacervate formation, typical of synthetic polyelectrolytes. This difference in phase behavior has likely been attributed to the hydrophobicity of chitosan and long semiflexible alginate and chitosan chains that restrict the conformational changes. Large amplitude oscillatory shear experiments captured nonlinear responses of PECs. The compositions of the PECs, determined as a function of salt concentration, signify the preferential partitioning of salt into the complex phase. Small-angle X-ray scattering of the salt-doped PECs indicates that the Kuhn length and radius of the alginate–chitosan associated structure qualitatively agree with the captured phase behavior and rheological data. This study provides insights into the structure–property as a function of salt concentration of natural polymer-based PECs necessary for developing functional materials from natural polyelectrolytes.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Soft matter approach for creating novel protein hydrogels using fractal whey protein assemblies as building blocks

In this study, mesoscopic sized fractal assembly (FA) particles were prepared using whey protein isolate; the coldset gelation properties of FA particles were investigated in-depth. Two types of FA particles (FA -62 and FA -90) with different mean sizes were synthesized through controlled thermal treatment of whey protein solutions at two concentrations (62 g/L and 90 g/L). Particle characteristics e.g. hydrodynamic radius, ζ-potential and surface hydrophobicity were dependent on pH and structure of FA. Transmission electron microscopy (TEM) observation confirmed the fractal morphology and small-angle X-ray scattering (SAXS) analysis suggested an internal fractal structure for the obtained FA particles. Eight cold-set FA protein gels (2 % w/v) were manufactured by controlling two gelling factors at two levels: pH (5.8 and 7.0) and Ca 2+ content (5 mM and 10 mM). Rheological characteristics in the large amplitude oscillatory shear regime revealed that pH 7.0 gels were softer and elastic while pH 5.8 gels were harder and brittle. Rheology Pipkin diagrams demonstrated that the strain softening/stiffening and the shear-thinning/thickening behaviors may be fine-tuned by manipulating the key gelation factors: e.g. FA structure, pH, and Ca 2+ . The entrainment speed-dependent friction coefficient curves showed that at an intermediate velocity regime (6-250 mm s -1 ), FA -90 particles induced hydrogels had superior lubrication effect compared to FA -62 gels. Further, this work demonstrated a food structure design approach regarding tuning texture and lubrication properties of protein gels without changing protein content and protein composition. The optimized protein hydrogels may be used as texturizer for "cleaner label" food formulas and/or as delivery system for carrying micronutrients.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Medium amplitude parallel superposition (MAPS) rheology. Part 2: Experimental protocols and data analysis

An experimental protocol is developed to directly measure the new material functions revealed by medium amplitude parallel superposition (MAPS) rheology. This protocol measures the medium amplitude response of a material to a simple shear deformation composed of three sine waves at different frequencies, revealing a rich dataset consisting of up to 19 measurements of the third-order complex modulus at distinct three-frequency coordinates. We discuss how the choice of input frequencies influences the features of the MAPS domain studied by the experiment. A polynomial interpolation method for reducing the bias of measured values from spectral leakage and reducing variance due to noise is discussed, including a derivation of the optimal range of amplitudes for the input signal. This leads to the conclusion that conducting the experiment in a stress-controlled fashion possesses a distinct advantage to the strain-controlled mode. The experimental protocol is demonstrated through measurements of the MAPS response of a model complex fluid: a surfactant solution of wormlike micelles. The resulting dataset is indeed large and feature-rich, while still acquired in a time comparable to similar medium amplitude oscillatory shear (MAOS) experiments. We demonstrate that the data represent measurements of an intrinsic material function by studying its internal consistency, compatibility with low-frequency predictions for Coleman–Noll simple fluids, and agreement with data obtained via MAOS amplitude sweeps. Finally, the data are compared to predictions from the corotational Maxwell model to demonstrate the power of MAPS rheology in determining whether a constitutive model is consistent with a material’s time-dependent response.

Lennon, Kyle R. (ORCID:0000000212515461)↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location o excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms o performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Seifert, Avi↗
NASA NTRS2000

Separation Control at Flight Reynolds Numbers: Lessons Learned and Future Directions

Active separation control, using periodic excitation, was studied experimentally at high Reynolds numbers. The effects of compressibility, mild sweep, location of excitation slot and steady momentum transfer on the efficacy of the method were identified. Tests conducted at chord Reynolds numbers as high as 40 x 10(exp 6) demonstrated that active control using oscillatory flow excitation can effectively delay flow separation from, and reattach separated flow to aerodynamic surfaces at flight conditions. The effective frequencies generate one to four vortices over the controlled region at all times, regardless of the Reynolds number. The vortices are initially amplified by the separated shear-layer, and after initiating reattachment, the strength of the vortices decay as they are convected downstream. Large amplitude, low frequency vortices break down to smaller ones upon introduction at the excitation slot. The effects of steady mass transfer were compared to those of periodic excitation. It was found that steady blowing is significantly inferior to periodic excitation in terms of performance benefits and that the response to steady blowing is abrupt, and therefore undesirable from a control point of view. Steady suction and periodic excitation are comparable in effectiveness and both exhibit a gradual response to changes in the magnitude of the control input. The combination of weak steady suction and periodic excitation is extremely effective while the addition of steady blowing could be detrimental. Compressibility effects are weak as long as separation is not caused by a shock-wave/boundary-layer interaction. The undesirable effects of the shock-induced separation could be alleviated by the introduction of periodic excitation upstream of the shock wave, inside the region of supersonic flow. The effects of mild sweep were also studied and periodic excitation was found to be very effective in reattaching three-dimensional separated flow. Scaling laws that correlate 2D and 3D controlled flows were tested and verified. Several performance benefits could be gained by applying the method to existing configurations, but it is expected that the full potential of the method can only be realized through the design of new configurations. A comprehensive, fully turbulent, database was generated in order to guide the development, and enable validation, of candidate unsteady CFD design tools.

Pack, LaTunia G.↗
NASA NTRS1997

Two Dimensional Parametric Studies of Wake Vortex Interaction with the Atmosphere

Results from parametric runs using two-dimensional TASS are presented. First, a set of experiments are presented that examine the sensitivity of the aircraft initiation height for an "in ground effect" case with weak crosswind. Interaction between the ground and the wake vortex produces an oscillatory rebound whose phase and amplitude are a function of the generation height. A second set of experiments are presented which examine the influence on crosswind shear. Shear layers, such as may be found between the nocturnal stable layer and the residual layer, can act to deflect vortices upward. Further investigation reveals that the second derivative of the crosswind can differentially reduce the descent speed of each member of a vortex pair, causing tilting of the vortex pair. If sufficiently large, the second derivative of crosswind can deflect the vortex pair upwards, with the sign of the second derivative determining which of the two vortices rises to a higher altitude. Linear shear, on the other hand, caused no change in the descent speed of the vortices; thus having no effect on the orientation of the vortices. Observed and model data from an actual case are presented in support of the conclusion regarding the influence of shear on rising vortices.

Proctor, Fred↗
NASA NTRS2001

Fundamental Processes of Atomization in Fluid-Fluid Flows

This report outlines the major results of the grant "Fundamental Processes of Atomization in Fluid-Fluid Flows." These include: 1) the demonstration that atomization in liquid/liquid shear flow is driven by a viscous shear instability that triggers the formation of a long thin sheet; 2) discovery of a new mode of interfacial instability for oscillatory two-layer systems whereby a mode that originates within the less viscous liquid phase causes interfacial deformation as the oscillation proceeds; 3) the demonstration that rivulet formation from gravity front occurs because the local front shape specified by gravity and surface tension changes from a nose to a wedge geometry, thus triggering a large increase in viscous resistance; and 4) extension of the studies on nonlinear wave evolution on falling films and in stratified flow, particularly the evolution towards large-amplitude solitary waves that tend to generate drops.

McCready, M. J.↗
NASA NTRS1997

Binary Oscillatory Crossflow Electrophoresis

Electrophoresis has long been recognized as an effective analytic technique for the separation of proteins and other charged species, however attempts at scaling up to accommodate commercial volumes have met with limited success. In this report we describe a novel electrophoretic separation technique - Binary Oscillatory Crossflow Electrophoresis (BOCE). Numerical simulations indicate that the technique has the potential for preparative scale throughputs with high resolution, while simultaneously avoiding many problems common to conventional electrophoresis. The technique utilizes the interaction of an oscillatory electric field and a transverse oscillatory shear flow to create an active binary filter for the separation of charged protein species. An oscillatory electric field is applied across the narrow gap of a rectangular channel inducing a periodic motion of charged protein species. The amplitude of this motion depends on the dimensionless electrophoretic mobility, alpha = E(sub o)mu/(omega)d, where E(sub o) is the amplitude of the electric field oscillations, mu is the dimensional mobility, omega is the angular frequency of oscillation and d is the channel gap width. An oscillatory shear flow is induced along the length of the channel resulting in the separation of species with different mobilities. We present a model that predicts the oscillatory behavior of charged species and allows estimation of both the magnitude of the induced convective velocity and the effective diffusivity as a function of a in infinitely long channels. Numerical results indicate that in addition to the mobility dependence, the steady state behavior of solute species may be strongly affected by oscillating fluid into and out of the active electric field region at the ends of the cell. The effect is most pronounced using time dependent shear flows of the same frequency (cos((omega)t)) flow mode) as the electric field oscillations. Under such conditions, experiments indicate that solute is drawn into the cell from reservoirs at both ends of the cell leading to a large mass build up. As a consequence, any initially induced mass flux will vanish after short times. This effect was not captured by the infinite channel model and hence numerical and experimental results deviated significantly. The revised model including finite cell lengths and reservoir volumes allowed quantitative predictions of the time history of the concentration profile throughout the system. This latter model accurately describes the fluxes observed for both oscillatory flow modes in experiments using single protein species. Based on the results obtained from research funded under NASA grant NAG-8-1080.S, we conclude that binary separations are not possible using purely oscillatory flow modes because of end effects associated with the cos((omega)t) mode. Our research shows, however, that a combination of cos(2(omega)t) and steady flow should lead to efficient separation free of end effects. This possibility is currently under investigation.

Molloy, Richard F.↗
NASA NTRS1990

Stability of an oscillated fluid with a uniform density gradient

Instabilities in a fluid with a constant density gradient that is subject to arbitrarily oriented oscillatory accelerations are considered. With the Boussinesq approximation and for the case of an unbounded fluid, transformation to Lagrangian coordinates allows the reduction of the problem to an ordinary differential equation for each three-dimensional wavenumber. The problem has three parameters: the nondimensional amplitude R of the base-state oscillation, the nondimensional level of background steady acceleration, which for some cases can be represented in terms of a local (in time) Richardson number Ri, and the Prandtl number Pr. Some general bounds on stability are derived. For Pr = 1 closed-form solutions are found for impulse (delta function) accelerations and a general asymptotic solution is constructed for large R and general imposed accelerations. The asymptotic solution takes advantage of the fact that at large R wave growth is concentrated at 'zero points'. These are times when the effective vertical wavenumber passes through zero. Kelvin-Helmholtz instabilities are found to dominate at low R, while Rayleigh-Taylor instabilities dominate at high R. At high R, the uniform shear of the Kelvin-Helmholtz case tends to distort and weaken instability waves. With unsteady flows, Ri = 1/4 is no longer an instability limit. Significant instabilities have been found for sinusoidal forcing for Ri up to 0.6.

Jacqmin, David↗