Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “irreversible strain effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Protocols and methodologies for acquiring and analyzing critical-current versus longitudinal-strain data in Bi 2 Sr 2 CaCu 2 O 8+x wires

Abstract In the literature on Bi 2 Sr 2 CaCu 2 O 8+ x (Bi-2212) superconducting wires, it is evident that measurement protocols for transport critical-current I c versus longitudinal strain ϵ and definitions of the so-called ‘strain limit’ are generally dissimilar. Yet, values obtained for the ‘strain limit’ are frequently assimilated to being those of the irreversible strain limit ϵ irr , regardless of the I c degradation-criterion used to define it. In effect, ϵ irr should correspond specifically to the I c ( ϵ ) irreversibility onset , where crack formation in Bi-2212 filaments presumably starts. Because I c ( ϵ ) degradation remains progressive over a fairly wide strain range beyond ϵ irr , the different I c degradation-criteria in use do not yield to the same result and, thus, are not equivalent from metrology perspective. Indeed, in studying densified samples of a modern Bi-2212 round wire, we found ϵ irr ≈ 0.4% and ϵ 5% ≈ 0.6% ( ϵ 5% being the strain where I c degrades by 5%). In this paper, we outline and suggest I c ( ϵ )-measurement protocols and data-analysis methodologies in the hope to converge the various approaches taken for studying Bi-2212 strain properties and, thus, remove related result discrepancies. A unified approach would enable more objective data comparisons among laboratories and among different Bi-2212 conductors. It would pave the way for more rigorous studies of effects potentially associated with wire design, powder, heat treatments, and other such parameters on the conductor’s strain properties.

protocols↗
DOE OSTI2023

Computation of the Strain Induced Critical Current Reduction in the 16 T Nb 3 Sn Test Facility Dipole

A test facility dipole is being developed at LBNL, targeting a 16 T field in a 144 mm wide aperture. The magnet uses a block design, with two double-pancake coils. In order to minimize motion under the large Lorentz forces, the coils are preloaded against a thick aluminum shell and iron yoke using bladder and key technology. It is then crucial to verify that the performance of the magnet is not degraded due to strain induced on the Nb 3 Sn conductor during assembly, cool-down and powering. The critical current of extracted strands was measured in a varying background magnetic field and as a function of the applied longitudinal strain. Finite element analysis was used to extract the strain state inside the superconducting strands during magnet assembly and operation. This strain was then compared to the measurements to evaluate potential reversible and irreversible effects on the magnet performances. Here the results suggest that the magnet can reach 16 T with sufficient margin, with no irreversible degradation in the high field region.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Effect of reversible dislocation-based deformation on nanoparticle strain at failure

Molecular dynamics simulations are used to isolate and quantify the reversible and irreversible mechanisms that contribute to deformation in platinum nanoparticles under compression. Quantitative analysis reveals how the nucleation and entanglement of dislocations can lead to reversible dislocation-based deformation. Simulations run at different temperatures and loading conditions show that the formation of entangled dislocations is more likely at higher temperatures and is facilitated by loading orientations where dislocations nucleate on intersecting slip planes. The presence of entangled dislocations increases the strain at failure due to the ability of those dislocations to accommodate strain reversibly. The results are corroborated by the observation of similar entangled dislocation loops during in situ compression experiments on nanoparticles of the same material. Altogether, these findings provide insight into the role of dislocations in both reversible and irreversible deformation and their implications for nanoparticle stability and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Bayesian calibration and uncertainty quantification of a rate-dependent cohesive zone model for polymer interfaces

In this work we present a rate-dependent cohesive zone model for the fracture of polymeric interfaces and performs a Bayesian calibration, an uncertainty quantification, and a sensitivity analysis for the model. The proposed cohesive zone model accounts for both reversible elastic and irreversible rate-dependent separation sliding deformation at the interface. The viscous dissipation due to the irreversible opening at the interface is modeled using elastic-viscoplastic kinematics that incorporates the effects of strain rate. Inverse calibration of parameters for such complex models through trial and error is challenging due to the large number of parameters of the model. Moreover, the calibrated parameter values are often non-unique and uncertain when the available experimental data is limited. To tackle this challenge, we employ a Bayesian calibration approach to identify parameters from experimental data, the resulting parameters significantly enhance the accuracy of the model. To quantify the uncertainty associated with the inverse parameter estimation, a modular Bayesian approach is employed to calibrate the unknown model parameters, accounting for the parameter uncertainty of the cohesive zone model. The advantages of the Bayesian calibration over a deterministic parameter fit are demonstrated. Further, to quantify the model uncertainties, such as incorrect assumptions or missing physics, a discrepancy function is introduced, which significantly improves the model’s prediction. Finally, the total uncertainty of the model is quantified in a predictive setting. A sensitivity analysis is performed to assess how changes in the input variables of the model affect the peak load, facilitating the identification of a concise set of highly influential parameters. The present approach can be used for calibration and uncertainty quantification for other complex computational mechanics models. It should also facilitate the designing of interface materials under uncertainty.

42 ENGINEERING↗
DOE OSTI2020

Coefficient of Thermal Expansion during Ratchet Growth of TATB Compactions

Triamino trinitrobenzene (TATB) is an insensitive high explosive, meaning that it is quite immune from accidental detonation and only performs in appropriately engineered configurations. While this is advantageous for applications, the TATB crystal is graphitic and possesses significant thermal and mechanical anisotropy. Compactions of TATB crystals, with or without binder, have been shown to have oriented TATB crystals that relate to the pressing geometry and process, and this TATB texture necessarily imparts microscale and macroscale anisotropy to the compaction. By a mechanism not fully understood, thermal cycling results in irreversible volume expansion (also called ratchet growth) of the compaction likely by creating stress points on the microscale. Changes in density caused by thermal cycling can certainly effect the explosive performance. Our past characterization of the ratchet growth phenomenon has focused on the magnitude of the irreversible strain as measured before and after a thermal cycle. Finally, in the work presented here, we analyze the evolving thermal expansion behavior during the ascending and descending temperature ramps, providing further insight into the material changes taking place during the ratchet growth phenomenon.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2025

Electric field driven domain wall dynamics in BaTiO 3 nanoparticles

We report a detailed investigation into the response of single BaTiO 3 (BTO) nanocrystals under applied electric fields (E-field) using Bragg coherent diffraction imaging. Our study reveals pronounced domain wall migration and expansion of a sample measure under applied electric field. The changes are most prominent at the surface of the nanocrystal, where the lack of external strain allows greater domain wall mobility. The observed domain shifts are correlated to the strength and orientation of the applied E-field, following a side-by-side domain model from Suzana []. Notably, we identified a critical electric field strength of 3 MV/m, which leads to irreversible structural changes, suggesting plastic deformation. The findings highlight how surface effects and intrinsic defects contribute to the enhanced dielectric properties of BTO at the nanoscale, in contrast to bulk materials, where strain limits domain mobility. These findings deepen our understanding of nanoscale dielectric behavior and inform the design of advanced nanoelectronic devices. Published by the American Physical Society 2025

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Manipulating Ferroelectric Topological Polar Structures with Twisted Light

Abstract The dynamic control of non‐equilibrium states represents a central challenge in condensed matter physics. While intense terahertz fields drive metal‐insulator transitions and ferroelectricity via soft phonon modes, recent theory suggests that twisted light with orbital angular momentum (OAM) offers a distinct route to manipulate ferroelectric order and stabilize topological excitations including skyrmions, vortices, and Hopfions. Control of ferroelectric polarization in quasi‐2D CsBiNb 2 O 7 (CBNO) is demonstrated using non‐resonant twisted ultra‐violet (UV) light (375 nm, 800 THz). Combining in situ X‐ray Bragg coherent diffractive imaging (BCDI), twisted optical Raman spectroscopy, and density functional theory (DFT), three‐dimensional (3D) ionic displacements, strain fields, and polarization changes are resolved in single crystals. Operando measurements reveal light‐induced strain hysteresis under twisted light–a hallmark of nonlinear, history‐dependent ferroelastic switching driven by OAM. Discrete, irreversible domain transitions emerge as the topological charge ℓ is cycled, stabilizing non‐trivial domain textures including vortex‐antivortex pairs, Bloch/anti‐Bloch points, and merons. These persist after OAM removal, indicating a memory effect. Competing mechanisms are discussed, including multiphoton absorption, strain‐mediated polarization switching, and defect‐wall interactions. The findings establish structured light as a tool for deterministic, reversible control of ferroic states, enabling optically reconfigurable non‐volatile devices.

Chemistry↗
DOE OSTI2021

High-temperature superconducting CORC ® wires with record-breaking axial tensile strain tolerance present a breakthrough for high-field magnets

Cuprate high-temperature superconductors (HTS), such as RE-Ba 2 Cu 3 O 7–δ (REBCO, RE = rare earth), (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O 10–x and Bi 2 Sr 2 CaCu 2 O 8–x , have enabled the development of high-field superconducting magnets capable of generating magnetic fields far exceeding 20 T. The brittle nature of HTS requires elaborate means to protect them against the high stresses and strains associated with high-field magnet operation, and so far, has prevented reliable high-field HTS magnets from becoming a reality. Here we report a more than tenfold increase in the irreversible strain limit under axial tension (epsilonirr) to over 7% in optimized high-current conductor on round core (CORC®) conductors, compared to the REBCO tapes from which the CORC® conductor is wound. Minimizing the tape winding pitch of the helical wind mechanically decouples the brittle REBCO film from the overall conductor. The REBCO tapes behave as springs, limiting the rate at which applied strain is transferred to the ceramic film. In addition, high-strength alloy cores allow the critical stress (ϵ crit ) under axial tension at which initial degradation of CORC® conductors occurs to exceed 600 MPa, making them one of the strongest superconductors available. Mechanically decoupling the ceramic REBCO films from the overall CORC® conductor allows effective protection against the high operating stresses in high-field magnets. Furthermore, this breakthrough presents a monumental shift for HTS magnet technology, bringing reliable high-field superconducting magnets for compact fusion machines, the next generation of particle accelerators, and 40–60 T research solenoids within reach.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Highly stretchable polymer semiconductor thin films with multi-modal energy dissipation and high relative stretchability

Abstract Stretchable polymer semiconductors (PSCs) have seen great advancements alongside the development of soft electronics. But it remains a challenge to simultaneously achieve high charge carrier mobility and stretchability. Herein, we report the finding that stretchable PSC thin films (<100-nm-thick) with high stretchability tend to exhibit multi-modal energy dissipation mechanisms and have a large relative stretchability ( rS ) defined by the ratio of the entropic energy dissipation to the enthalpic energy dissipation under strain. They effectively recovered the original molecular ordering, as well as electrical performance, after strain was released. The highest rS value with a model polymer (P4) exhibited an average charge carrier mobility of 0.2 cm 2 V −1 s −1 under 100% biaxial strain, while PSCs with low rS values showed irreversible morphology changes and rapid degradation of electrical performance under strain. These results suggest rS can be used as a parameter to compare the reliability and reversibility of stretchable PSC thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Thickness-dependent phase transition kinetics in lithium-intercalated MoS 2

The phase transitions of two-dimensional (2D) materials are key to the operation of many devices with applications including energy storage and low power electronics. Nanoscale confinement in the form of reduced thickness can modulate the phase transitions of 2D materials both in their thermodynamics and kinetics. Here, using in situ Raman spectroscopy we demonstrate that reducing the thickness of MoS 2 below five layers slows the kinetics of the phase transition from 2H- to 1T'-MoS 2 induced by the electrochemical intercalation of lithium. In this study, we observe that the growth rate of 1T' domains is suppressed in thin MoS 2 supported by SiO 2 , and attribute this growth suppression to increased interfacial effects as the thickness is reduced below 5 nm. In this study, the suppressed kinetics can be reversed by placing MoS 2 on a 2D hexagonal boron nitride ( h BN) support, which readily facilitates the release of strain induced by the phase transition. Additionally, we show that the irreversible conversion of intercalated 1T'-MoS 2 into Li2S and Mo is also thickness-dependent and the stability of 1T'-MoS 2 is significantly increased below five layers, requiring a much higher applied electrochemical potential to break down 1T'-MoS 2 into Li 2 S and Mo nanoclusters.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Power-Law Decrease in Interfacial Resistance Between Li 7 La 3 Zr 2 O 12 and Lithium Metal After Removing Stack Pressure

The high interfacial resistance between solid electrolytes and lithium metal is a hurdle to developing all solid-state batteries. External pressure applied on the lithium and solid electrolyte interface prior to electrochemical cycling is known to effectively lower the interfacial resistance. Here we report that the interfacial resistance between Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) and lithium metal decreases over time even after removing the external pressure. The irreversible decrease of interfacial resistance can be understood by a gradual reduction of the total energy of the system, including strain energy and interfacial energy. Under external pressure exceeding ~25 MPa, however, lithium can be squeezed into LLZTO, fracturing the ceramic solid electrolyte. As a result, these observations can help improve the understanding of lithium metal creep and the interactions between garnet-type solid electrolytes and lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2021

Damage Modeling of Solid Oxide Fuel Cells Accounting for Redox Effects

This work applies a multiscale mechanistic damage model developed for brittle ceramics and implemented in commercial finite element (FE) packages via user subroutines to study progressive damage in solid oxide fuel cells (SOFC) subjected to thermomechanical loading under normal operating and shutdown conditions including redox effects. The damage model captures the micromechanics of stiffness reduction due to material porosity change and microcracking and integrates the as-obtained stiffness reduction law into a continuum damage mechanics (CDM) formulation for the evolution of microcracks up to fracture. The volumetric “swelling” that occurs during redox is treated in constitutive modeling similarly to thermal expansion, but swelling strains are irreversible. Furthermore, this damage model was first validated through predictions of strength and stress-strain response for the SOFC electrode materials. Next, it has been applied to predict the potential for degradation in a generic planar SOFC stack with large active area cells. Multicell stack models were simulated in both co-flow and counter-flow configurations. In addition, a constant temperature redox cycle was also simulated to capture overall cell electrode damage due to volumetric swelling of the nickel (Ni)-based anode in the anode-supported cells.

25 ENERGY STORAGE↗
DOE OSTI2019

Dilation Behavior of Thermal Spray Coatings

The thermal expansion of a thermally sprayed coating material is an important design-relevant property from both processing and application service points of view. High thermal stresses and residual strains can arise during deposition, and thermal exposure in service. The linkage to process conditions which can impact both physical and chemical attributes of the microstructure and consequently its expansion behavior is of great importance. The observed dilation response of various coatings is discussed based on the processing effects that induce differences in microstructural features and the impact of residual strain and annealing of defects on the dilation behavior during first thermal exposure. The coefficient of thermal expansion (CTE) of coatings was found to approach the bulk when the material is not sensitive to oxidation in-flight. For those materials sensitive to oxidation, mathematical models used to describe effective properties of composite materials were adopted to describe the CTE property. A large irreversible dilation change was found in the first heating cycle due to defect annealing (referred to as thermal shakedown). Several reasons are hypothesized for the magnitude of such dilation change. Finally, together, the paper presents a comprehensive analysis of thermal expansion behavior of a diversity of thermal spray processed materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Bounds on the Rate-Dependent Plastic Flow of Tantalum up to 75 GPa

In this study we report on the continued development of thermodynamics-based analysis of shock waves propagation with the objective of extracting information related to materials strength at high strain rates and pressures. Building on previous results reported for peak stresses of 10 GPa and 25 GPa, we present a series of three-step gas-gun shock experiments designed to explore the pressure and strain rate dependence of plastic flow in polycrystalline tantalum. These experiments at nominal peak stresses of 50 GPa and 75 GPa show the irreversible deformation before pullback to be almost entirely confined to the shock loading, with negligible plastic relaxation on the post-shock plateau. We also add a reverse-ballistics shot at 25 GPa, which was designed to reveal the pullback response with negligible interference from free-surface effects. General thermodynamic considerations allow us to place bounds on the plastic behavior even for parts of the curve that change far too rapidly for the velocimetric time resolution of (conservatively) ~ 5 ns. To analyze the data, we found it necessary to substantially improve the interpolation/extrapolation scheme in order to improve its robustness, flexibility and range of applicability. We describe the new scheme based on splines, as well as an extension of free-surface corrections to the post-shock rarefaction waves. Reanalysis with the new scheme produces results essentially within the error bars previously reported, showing that the known systematic errors associated with free-surface effects are relatively inconsequential for determining thermodynamic paths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Proppant embedment in coal and shale: Impacts of stress hardening and sorption

During methane production in CBM reservoirs, the influence of proppant embedment and permeability damage cannot be neglected – especially where the wall-rock is soft. Effective stresses are elevated during methane recovery, increasing both normal loading stress and confinement and simultaneously overprinting sorption-induced volumetric strains. Experiments and analytic modeling are conducted to define key mechanisms controlling these competitive effects. We independently measure overall sample compaction (external LVDT) and local strain (strain gauge) in the matrix to deconvolve proppant embedment in a propped fracture for different conditions of confining stress. The results show symptomatic behaviors of elastic (shale) and elastoplastic (coal) responses of embedment. Different from shale, the evolution of embedment is convex upwards with increased stress where indented depth increases more rapidly as loading stress increases under constant confinement. In addition, a stress-hardening effect is found to play a pivotal role in determining the characteristics of indentation, which are examined in terms of evolution profiles, deformation regimes, embedment slopes, curvatures, yield points and irreversible indentations. Based on the experimental observations a semianalytical model predicts indentation and the evolution of propped permeability under recreated in-situ stress conditions. A simplified case study is conducted to further illustrate the evolution of aperture and permeability of a propped fracture in CBM reservoirs. The modeling results suggest that proppant embedment is significantly overestimated if the variable stress-hardening (VSH) effect is neglected, especially when effective stress is large. Moreover, a decrease in indentation depth possibly occurs during late stage methane production, resulting in a reversal/recovery in fracture closure. This is because desorption-induced shrinkage becomes the predominant effect, causing an increase in aperture and a reduction in the indented volume of proppant. The resulting recovery in permeability implies that the propped coal fracture has the potential to optimally facilitate methane production as a pathway, even at high closure stresses generated by methane drainage.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Constraining Interlayer Slipping in P2-Type Layered Oxides with Oxygen Redox by Constructing Strong Covalent Bonds

Lattice oxygen redox (LOR) in P2-type layered oxides is an effective strategy to break through the limit of energy density of conventional cathodes due to its high redox potential (>4 V vs. Na + /Na) as well as extra capacity. Nevertheless, LOR induced local structure distortion and irreversible phase transitions cause serious electrochemical performance degradation, hindering the practical applications. In this work, we propose that the generation of the OP4 phase can be replaced with the Z phase by introducing Sb element with higher ionic potential and strong covalent bonds within the TMO 6 octahedron. Z phase transition is realized by constraining interlayer slipping between adjacent TM layers compared to OP4, which reduces the strain in the layered structure, lowers the Na+ diffusion energy barrier and creates more efficient Na+ diffusion channels. Consequently, Sb-substituted oxides demonstrates excellent kinetics, rate capability (79 mAh g -1 at 1 A g -1 ) in half cell and a high energy density of 487 Wh kg -1 (on cathode) in full cell.

25 ENERGY STORAGE↗
DOE OSTI2024

Neutron and photon in-vivo materials characterization at the evolving plasma-material interface in plasma-burning fusion environments

This report includes the first set of MOSS data collected in the context of fusion-relevant plasma-material interactions. The data collected show that the surface curvature and stress irreversibly change during low-energy deuterium ion irradiation. This holds for both tungsten thin films, bulk tungsten, and single-crystal silicon. Meanwhile, argon irradiation did not produce this same effect. The surface morphology of the exposed samples was virtually identical regardless of gas species. There were, however, some surface chemistry differences between argon-exposed and deuterium-exposed samples, mainly concerning the oxide states of the W4f XPS signal. The changes in surface chemistry could be due to hydrogen dynamics on the tungsten surfaces, though further investigation will be required with in-situ irradiation and analysis. The changes in surface stress could also not be explained by temperature alone, as the temperature reached during the ion irradiations was too low to induce non-elastic strain. With this in mind, deuterium retention in the materials could change the surface curvature and stress. To confirm this, further work will be needed to quantify the change in curvature and relate it to ion flux, fluence, and deuterium retention. Unfortunately, when this work was conducted, the experimental setup for thermal desorption spectroscopy was not operating correctly, and that work could not be included in this dissertation. Despite experimental difficulties, this work shows the first results of a promising technique to study deuterium dynamics in tungsten-based reconstituted thin films.

36 MATERIALS SCIENCE↗