Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “inverse pole figures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Visualization of texture components using MTEX

Knowledge of the appearance of texture components and fibres in pole figures, in inverse pole figures and in Euler space is fundamental for texture analysis. For cubic crystal systems, such as steels, an extensive literature exists and, for example, the book by Matthies, Vinel & Helming [Standard Distributions in Texture Analysis: Maps for the Case of Cubic Orthorhomic Symmetry, (1987), Akademie-Verlag Berlin] provides an atlas to identify texture components. For lower crystal symmetries, however, equivalent comprehensive overviews that can serve as guidance for the interpretation of experimental textures do not exist. Here, this paper closes this gap by providing a set of scripts for the MTEX package [Bachmann, Hielscher & Schaeben (2010). Solid State Phenom.160, 63–68] that allow the texture practitioner to compile such an atlas for a given material system, thus aiding orientation distribution function analysis also for non-cubic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and Mechanical Properties of the AA7075 Tube Fabricated using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) experimental setup and tooling were adopted for extruding thin-walled AA7075 aluminum tube from as-cast non-homogenized billet material in a single run. The mechanical and microstructural characterizations were performed on the extrudate in the as-extruded condition without subsequent heat treating. It was shown that the ShAPE process developed a significantly refined microstructure with uniform and almost equiaxed grain structure on both hoop and axial cross-sections of the extrudate as well as through the thickness of the material. The pole figures and inverse pole figures of the EBSD data showed an strong shear texture development, and it was found out that axial shear is the dominant deformation mechanism in the regions near the inner surface of the tube, while combined axial and torsional shears are the two dominant modes of deformation near the outer surface of the extrudate. As for the mechanical properties, there was an increase of 150% and 73% in the yield and ultimate strengths of the tube produced using ShAPE process, respectively, and a 18% decrease in maximum uniform plastic elongation compared to the conventionally extruded AA7075-O tube.

Shear Assisted Processing and Extrusion, Friction ↗
DOE OSTI2020

Influence of defect characteristics on tensile deformation of an additively manufactured stainless steel: Evolutions of texture and intergranular strain

The micromechanics of plastic deformation behavior of a selective laser melt processed austenitic stainless steel were studied by investigating the evolutions of texture and intergranular strain using in situ high-energy synchrotron x-ray diffraction (sXRD). The effects of defect characteristics on tensile behavior were studied using three different samples: a near full-density sample with elliptical closed voids and two samples with lack-of-fusion (LOF) defects tensile loaded either perpendicular or parallel to their major axes. The evolutions of pole figures and inverse pole figures show that the full-density specimen develops a strong (111)/(200) fiber texture along the loading direction. For both LOF specimens, the evolution of texture is qualitatively similar to the full-density counterpart, but the development of the fiber texture was much slower, indicating a limited plasticity at a given macroscopic strain. The intergranular strain evolution in the full-density specimen is similar to that of a wrought 316L stainless steel. Conversely, a significantly different intergranular strain development was observed in a LOF specimen, where tensile strain development was observed in both the axial and transverse directions. Finally, the influence of defect type, density, and orientation on the local stress states in the steel matrix and the evolutions of intergranular strains is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In situ synchrotron X-ray diffraction analysis of ultrasonically assisted microstructure refinement during laser melting process

This work investigates the effect of ultrasonic treatment (UST) on the microstructure of AA4043 alloy during laser melting process. Here, the study utilizes in situ synchrotron X-ray diffraction (SXRD) and postmortem electron backscatter diffraction (EBSD) techniques to examine the ultrasonic grain refinement mechanism. The SXRD diffraction patterns exhibit higher continuity of major diffraction rings in the UST-test pattern, indicating a more refined grain structure. The presence of new diffraction spots in the post-test diffraction pattern with UST suggests the breakdown of epitaxial growth of columnar dendrites during solidification. Thermal profiles determined by analyzing the lattice parameter evolution show a faster cooling rate with UST. The inverse pole figures and aspect ratio distribution from EBSD reveal that the UST samples exhibit a refined, more equiaxed grain structure along the weld centerline. UST sample also develops more fine-sized low angle grain boundaries (LAGBs). These features offer better hot-cracking resistance in aluminum alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Deformation of binary and boron-doped Ni 3 Al alloys at high pressures studied with synchrotron x-ray diffraction

In situ x-ray synchrotron diffraction experiments were carried out on nickel-based high-strength superalloys under pressure to understand their deformation mechanism using a diamond anvil cell (DAC). Radial x-ray diffraction determines the room-temperature equations of state and yield strengths of binary Ni 3 Al alloy and 500 ppm boron-doped Ni 3 Al to pressures of 20 and 46 GPa, respectively. Crystallographic preferred orientations observed in these superalloys due to anisotropic stress field in DAC indicate the onset of plastic deformation. Inverse pole figure analysis reveals that the underlying deformation mechanisms change from an octahedral slip to a simultaneous activation of octahedral and cube slips upon doping with boron. The yield-strength values were found to increase with pressure and are comparable to those determined from axial diffraction experiments. The results indicate that the yield strength of Ni 3 Al:B is about 0.5 GPa higher (at pressures below 20 GPa) due to grain boundary strengthening by boron. It is shown that due to high elastic anisotropy of Ni 3 Al alloy, the yield-strength estimations from diffraction experiments strongly depend on the micromechanical model used to convert the measured elastic strains into stresses.

42 ENGINEERING↗
DOE OSTI2024

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

316L stainless steel↗
DOE OSTI2024

Deformation and Transformation Textures in the NaMgF3 Neighborite—Post-Perovskite System

The D″ region of the lower mantle, which lies just above the core–mantle boundary, is distinct from the bulk of the lower mantle in that it exhibits complex seismic heterogeneity and seismic anisotropy. Seismic anisotropy in this region is likely to be largely due to the deformation-induced texture (crystallographic preferred orientation) development of the constituent mineral phases. Thus, seismic anisotropy can provide a marker for deformation processes occurring in this dynamic region of the Earth. Post-perovskite-structured (Mg,Fe)SiO3 is believed to be the dominant mineral phase in many regions of the D”. As such, understanding deformation mechanisms and texture development in post-perovskite is important for the interpretation of observed seismic anisotropy. Here, we report on high-pressure diamond anvil cell deformation experiments on NaMgF3 neighborite (perovskite structure) and post-perovskite. During deformation, neighborite develops a 100 texture, as has been previously observed, both in NaMgF3 and MgSiO3 perovskite. Upon transformation to the post-perovskite phase, an initial texture of {130} at high angles to compression is observed, indicating that the {100} planes of perovskite become the ~{130} planes of post-perovskite. Further compression results in the development of a shoulder towards (001) in the inverse pole figure. Plasticity modeling using the elasto-viscoplastic self-consistent code shows this texture evolution to be most consistent with deformation on (001)[100] with some contribution of glide on (100)[010] and (001)<110> in NaMgF3 post-perovskite. The transformation and deformation mechanisms observed in this study in the NaMgF3 system are consistent with the behavior generally observed in other perovskite–post-perovskite systems, including the MgSiO3 system. This shows that NaMgF3 is a good analog for the mantle bridgmanite and MgSiO3 post-perovskite.

Geochemistry & Geophysics↗
DOE OSTI2022

Reconstructing parent microstructures in martensitic and pearlitic Ti-Cu

Evaluating the microstructural evolution of parent phases has long been a challenge in metals with a partial or complete solid state transformation. Most parent microstructure evolution has to be inferred from the product microstructure, with some information permanently lost. Parent microstructure reconstructions relying on orientation relationships and EBSD data are a useful tool to overcome this challenge, though much background knowledge is required to do so. Here, this work introduces a reconstruction process for a eutectoid composition Ti-Cu binary alloy to evaluate the high temperature β-Ti phase from martensitic and pearlitic product microstructures. Martensitic microstructures were accurately reconstructed, enabling elucidation of β-Ti grain size and texture, and the employed script included for scientific reference. Pearlitic microstructures did not reconstruct effectively with the current process. However, new insight into the interfacial crystallographic orientations of pearlitic Ti-Cu microstructures was gleaned via this analysis, and future investigations of interest are discussed accordingly. Ultimately, these findings demonstrate tools widely implemented on conventional titanium and ferrous alloys can also be applied to understand parent microstructures in Ti-Cu and other alloys of emerging interest. This is especially of use as new manufacturing processes for such materials require understanding how parent phase microstructures respond to new, novel material processing such as AM.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantitative texture analysis at the WAND 2 and HIDRA diffractometers

Data collection and analysis strategies have been developed for efficient and reliable crystallographic texture measurements at two recently upgraded neutron diffractometers: the Wide Angle Neutron Diffractometer Squared (WAND 2 ) and the High Intensity Diffractometer for Residual Stress Analysis (HIDRA) at the High Flux Isotope Reactor located at Oak Ridge National Laboratory. These methods are demonstrated using measurements on a variety of textured samples, including multi-phase steel composites and polycrystalline calcite (CaCO 3 ). Reference measurements were also made at VULCAN, the engineering diffractometer located at the Spallation Neutron Source. The texture data obtained on the different instruments are in agreement, and WAND 2 is more time efficient than HIDRA. Two analysis methods were investigated, single-peak fitting to obtain individual pole figures for inversion and Rietveld texture analysis using MAUD. Here, the impact of the differences between the various textures obtained was evaluated through the calculation of diffraction elastic constants, which is one application of the texture data collected. Both instruments were found to provide texture data that are suitable for complementing other analyses, such as residual stress mapping.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Inversion, chemical complexity, and interstitial transport in spinels

Abstract Spinels with the generic chemical formula AB 2 O 4 have potential applications in nuclear energy and batteries. In both cases, their functionality is related to mass transport through the crystal. Here, using long‐time atomistic simulations, we examine the impact of the cation structure on interstitial transport in two spinel chemistries, inverse MgGa 2 O 4 and double MgAlGaO 4 . We emphasize two aspects of the transport properties: the unit mechanisms that are described by individual barriers, for which we introduce pole‐figure‐like plots, and the aggregate behavior of those unit mechanisms. Compared to previous work on normal spinels, we find that inversion significantly reduces the rate of interstitial transport in these structures and has an impact on the stability of defects as they move through the lattice. In particular, B cation interstitials are found to be kinetically stable only in the inverse MgGa 2 O 4 . These results provide new insight into relationship between structure, chemistry, and transport in spinels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗