Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Minimizing Interfacial Resistance between Polymer Electrolytes and Metal Electrodes Using Applied Current

Reducing the interfacial resistance between different phases in electrochemical systems is crucial for enabling practical applications. In this work, we proposed a process for reducing the interfacial resistance between polymer electrolytes and metal electrodes. Thus far in the literature, the lowest interfacial resistance reported in these systems is 15 Ω·cm2. In this study, assembled and preconditioned symmetric cells with lithium–indium alloy electrodes showed similar values. The current through the cell was increased in steps up to the limiting current. This resulted in a permanent decrease of the interfacial resistance to values as low as 1 Ω·cm2, a value that is comparable to that of optimized lithium-ion batteries. The proposed process is general, and it could be applied to any combination of polymer electrolytes and metal electrodes.

Lee, Jaeyong↗
DOE OSTI2021

A Power-Law Decrease in Interfacial Resistance Between Li 7 La 3 Zr 2 O 12 and Lithium Metal After Removing Stack Pressure

The high interfacial resistance between solid electrolytes and lithium metal is a hurdle to developing all solid-state batteries. External pressure applied on the lithium and solid electrolyte interface prior to electrochemical cycling is known to effectively lower the interfacial resistance. Here we report that the interfacial resistance between Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO) and lithium metal decreases over time even after removing the external pressure. The irreversible decrease of interfacial resistance can be understood by a gradual reduction of the total energy of the system, including strain energy and interfacial energy. Under external pressure exceeding ~25 MPa, however, lithium can be squeezed into LLZTO, fracturing the ceramic solid electrolyte. As a result, these observations can help improve the understanding of lithium metal creep and the interactions between garnet-type solid electrolytes and lithium metal.

25 ENERGY STORAGE↗
NASA NTRS1987

New flange correction formula applied to interfacial resistance measurements of ohmic contacts to GaAs

A quasi-two-dimensional analytical model is developed to account for vertical and horizontal current flow in and adjacent to a square ohmic contact between a metal and a thin semiconducting strip which is wider than the contact. The model includes side taps to the contact area for voltage probing and relates the 'apparent' interfacial resistivity to the (true) interfacial resistivity, the sheet resistance of the semiconducting layer, the contact size, and the width of the 'flange' around the contact. This relation is checked against numerical simulations. With the help of the model, interfacial resistivities of ohmic contacts to GaAs were extracted and found independent of contact size in the range of 1.5-10 microns.

Lieneweg, Udo↗
DOE OSTI2020

Effect of Liquid Electrolyte Soaking on the Interfacial Resistance of Li 7 La 3 Zr 2 O 1 2 for All-Solid-State Lithium Batteries

In this work, the impact of liquid electrolyte soaking on the interfacial resistance between the garnet-structured Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte and metallic lithium has been studied. Lithium carbonate (Li 2 CO 3 ) formed by inadvertent exposure of LLZO to ambient conditions is generally known to increase interfacial impedance and decrease lithium wettability. Soaking LLZO powders and pellets in the electrolyte containing lithium tetrafluoroborate (LiBF 4 ) shows a significantly reduced interfacial resistance and improved contact between lithium and LLZO. Raman spectroscopy, X-ray diffraction, and soft X-ray absorption spectroscopy reveal how Li 2 CO 3 is continuously removed with increasing soaking time. On-line mass spectrometry and free energy calculations show how LiBF 4 reacts with surface carbonate to form carbon dioxide. Using a very simple and scalable process that does not involve heat-treatment and expensive coating techniques, we show that the Li–LLZO interfacial resistance can be reduced by an order of magnitude.

25 ENERGY STORAGE↗
DOE OSTI2020

Direct Measurement of Crossover and Interfacial Resistance of Ion-Exchange Membranes in All-Vanadium Redox Flow Batteries

Among various components commonly used in redox flow batteries (RFBs), the separator plays a significant role, influencing resistance to current as well as capacity decay via unintended crossover. It is well-established that the ohmic overpotential is dominated by the membrane and interfacial resistance in most aqueous RFBs. The ultimate goal of engineering membranes is to improve the ionic conductivity while keeping crossover at a minimum. One of the major issues yet to be addressed is the contribution of interfacial phenomena in the influence of ionic and water transport through the membrane. In this work, we have utilized a novel experimental system capable of measuring the ionic crossover in real-time to quantify the permeability of ionic species. Specifically, we have focused on quantifying the contributions from the interfacial resistance to ionic crossover. The trade-off between the mass and ionic transport impedance caused by the interface of the membranes has been addressed. The MacMullin number has been quantified for a series of electrolyte configurations and a correlation between the ionic conductivity of the contacting electrolyte and the Nafion® membrane has been established. The performance of individual ion-exchange membranes along with a stack of various separators have been explored. We have found that utilizing a stack of membranes is significantly beneficial in reducing the electroactive species crossover in redox flow batteries compared to a single membrane of the same fold thickness. For example, we have demonstrated that the utilization of five layers of Nafion ® 211 membrane reduces the crossover by 37% while only increasing the area-specific resistance (ASR) by 15% compared to a single layer Nafion ® 115 membrane. Therefore, the influence of interfacial impedance in reducing the vanadium ion crossover is substantially higher compared to a corresponding increase in ASR, indicating that mass and ohmic interfacial resistances are dissimilar. We have expanded our analysis to a combination of commercially available ion-exchange membranes and provided a design chart for membrane selection based on the application of interest (short duration/high-performance vs. long-term durability). The results of this study provide a deeper insight into the optimization of all-vanadium redox flow batteries (VRFBs).

UV/Vis spectroscopy↗
DOE OSTI2023

Thin film design of amorphous hafnium oxide nanocomposites enabling strong interfacial resistive switching uniformity

A design concept of phase-separated amorphous nanocomposite thin films is presented that realizes interfacial resistive switching (RS) in hafnium-oxide-based devices. The films are formed by incorporating an average of 7% Ba into hafnium oxide during pulsed laser deposition at temperatures ≤400°C. The added Ba prevents the films from crystallizing and leads to ~20-nm-thin films consisting of an amorphous HfO x host matrix interspersed with ~2-nm-wide, ~5-to-10-nm-pitch Ba-rich amorphous nanocolumns penetrating approximately two-thirds through the films. This restricts the RS to an interfacial Schottky-like energy barrier whose magnitude is tuned by ionic migration under an applied electric field. Resulting devices achieve stable cycle-to-cycle, device-to-device, and sample-to-sample reproducibility with a measured switching endurance of ≥10 4 cycles for a memory window ≥10 at switching voltages of ±2 V. Each device can be set to multiple intermediate resistance states, which enables synaptic spike-timing–dependent plasticity. The presented concept unlocks additional design variables for RS devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Intrinsic thermal interfacial resistance measurement in bonded metal–polymer foils

Heat conduction through bonded metal–polymer interfaces often limits the overall heat transfer in electronic packaging, batteries, and heat recovery systems. To design the thermal circuit in such systems, it is essential to measure the thermal interfacial resistance (TIR) across ~1 µm to 100 µm junctions. Previously reported TIR of metal–polymer junctions utilize ASTM E1530-based two-block systems that measure the TIR by applying pressure across the interface through external heating and cooling blocks. Here, we report a novel modification of the ASTM-E1530 technique that employs integrated heaters and sensors to provide an intrinsic TIR measurement of an adhesively bonded metal–polymer junction. We design the measurement technique using finite element simulations to either passively suppress or actively compensate the lateral heat diffusion through the polymer, which can minimize the systematic error to ≲5%. Through proof-of-concept experiments, we report the TIR of metal–polymer interfaces made from DuPont’s Pyralux double-side copper-clad laminates, commonly used in flexible printed circuit boards. Our TIR measurement errors are <10%. We highlight additional sources of errors due to non-idealities in the experiment and discuss possible ways to overcome them. Our measurement technique is also applicable to interfaces that are electrically insulating such as adhesively joined metal–metal junctions and sputter-coated or welded metal–polymer junctions. Altogether, the technique is capable of measuring TIR ≳10 –5 m 2 KW –1 in bonded metal–polymer foils and can be tailored for in situ measurements in flexible electronics, circuit packaging, and other hybrid metal–polymer systems.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Deciphering Interfacial Chemical and Electrochemical Reactions of Sulfide-Based All-Solid-State Batteries

Large interfacial resistance resulting from interfacial reactions is widely acknowledged as one of the main challenges in sulfide electrolytes (SEs)-based all-solid-state lithium batteries (ASSLBs). However, the root cause of the large interfacial resistance between the SEs and typical layered oxide cathodes is not fully understood yet. Here we deciphered that interfacial oxygen loss from single-crystal LiNi 0.5 Mn 0.3 Co 0.2 O 2 (SC-NMC532) chemically oxidizes Li 10 GeP 2 S 12 , generating oxygen-containing interfacial species. Meanwhile, the interfacial oxygen loss also induces a structural change of oxide cathodes (layered-to-rocksalt). Besides, the high operation voltage can electrochemically oxidize SEs to form non-oxygen species (e.g. polysulfides). These chemically and electrochemically oxidized species, together with the interfacial structural change, are responsible for the large interfacial resistance at the cathode interface. More importantly, the widely adopted interfacial coating strategy is effective in suppressing chemically oxidized oxygen-containing species and mitigating the coincident interfacial structural change but is unable to prevent electrochemically induced non-oxygen species. These findings provide a deeper insight into the large interfacial resistance between the typical SE and layered oxide cathodes, which may be of assistance for the rational interface design of SE-based ASSLBs in future.

25 ENERGY STORAGE↗
DOE OSTI2020

The Role of Interfacial Thermal Resistance in Li-Ion Battery Thermal Management: Preprint

Temperature critically affects the performance, life and safety of lithium-ion batteries. Therefore, it is essential to understand heat generation and dissipation within individual battery cells and battery packs to plan a proper thermal management strategy. One of the key challenges is that interfacial heat transfer of a battery unit is difficult to quantify. The steady-state absolute method and the transient laser-flash-diffusivity method were employed to measure heat conductivities of battery layer stacks and individual battery layer separately. Results show flash diffusivity method gives higher thermal conductivity at both cross-plane and in-plane directions. The difference is primarily caused by interfacial thermal resistance so that it can be estimated by steady-state and transient measurements. To investigate the effects of interfacial thermal transport beyond individual cell level, a multiphysics battery model is used. The model is built upon a multi-scale multi-domain modeling framework for battery packs that accounts for the interplay across multiple physical phenomena. Benefits of a battery module using thermal management materials are quantified through numerical experiments. During a thermal runaway event, it is found interfacial thermal resistance can mitigate thermal runaway in a battery module by significantly reducing heat transfer between cells.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

The impact of residual solvent on catholyte performance in solid-state batteries

All-solid-state batteries (ASSBs) are attractive due to their safety, use of the Li metal anode, high energy density, and innovative processing routes. However, high interfacial resistance, especially on the cathode side, is one of the major challenges for commercialization of ASSBs. Catholyte, either a liquid or solid, is added to lower the cathode/electrolyte interfacial resistance. In this study, we find that residual N-methylpyrrolidone solvent remaining in a PVDF/LiTFSI solid polymer catholyte after incomplete drying can dramatically lower the interfacial resistance between the Li 6.25 Al 0.25 La 3 Zr 2 O 12 electrolyte and LiNi 1/3 Mn 1/3 Co 1/3 O 2 cathode-active material. Cells with varying amounts of residual solvent are compared to optimize the residual solvent loading. With moderate residual solvent, the discharge capacity reaches 142 mA h g -1 when cycled at 25 °C and 0.5 C and the capacity retention is 60.5% after 125 cycles. Discharge capacity retention is improved at -10 °C. The conductivity of the free-standing PVDF/LiTFSI film, mimicking the PVDF/LiTFSI catholyte, verifies the role of residual NMP in the cathode. Finally, this study demonstrates the possibility of widely differing results for ASSBs when the cathode is not completely dried. Also, it provides a hint for a potential method to lower the cathode/electrolyte interfacial resistance.

25 ENERGY STORAGE↗
DOE OSTI2021

Interfacial Effects on Transport Coefficient Measurements in Li-ion Battery Electrolytes

Development of Li + -containing electrolytes with improved transport properties requires reliable, reproducible, and ideally low volume techniques to rigorously understand ion-transport with varying composition. Precisely measuring the complete set of transport coefficients in liquid electrolytes under battery-relevant operating conditions is difficult and the reliability of these methods are sparsely described in electrolyte transport literature. In this work, we apply a potentiostatic polarization-based transport characterization approach typically used for polymer electrolytes to liquid electrolyte systems in an attempt to fully measure all transport coefficients (conductivity, total salt diffusion coefficient, thermodynamic factor and transference number) for the model system of LiPF 6 in an ethylene carbonate—ethyl methyl carbonate (EC:EMC) mixture. Using systematic timescale and statistical analyses, we find that transport coefficients measured using potentiostatic polarization of Li-Li symmetric cells exhibit strong correlation to Li electrode interfacial resistance, indicating that such methods are probing both bulk and interfacial phenomena. This reveals a major roadblock in characterizing electrolyte systems where the interfacial resistance is significantly larger than ohmic electrolyte resistance. As a result, we find that methods that rely on potentiostatic Li metal stripping/plating do not readily result in reliable liquid electrolyte transport coefficients, unlike similar methods for solid polymer electrolytes, where interfacial resistances are typically smaller than electrolyte resistances at the elevated temperatures typically of interest for such electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2025

Measurement of interfacial thermal resistance in high-energy-density matter

Heat transport across interfaces is a ubiquitous phenomenon with many unresolved aspects. In particular, it is unknown if an interfacial thermal resistance (ITR) occurs in matter with high-energy-density where free electrons dominate the heat conduction. Here, we report on the first experimental evidence that a significant heat barrier is present between two different regions of high-energy-density matter: a strongly heated tungsten wire and a surrounding plastic layer that stays relatively cold. We use diffraction-enhanced imaging to track the time evolution of density discontinuities and reconstruct the temperature evolution in the quasi-stationary stage. The clear signatures of a temperature jump demonstrate the importance of the ITR for strongly heated systems with far-reaching implications for interpreting experiments and applications like inertial confinement fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Tin-based ionic chaperone phases to improve low temperature molten sodium–NaSICON interfaces

High temperature operation of molten sodium batteries impacts cost, reliability, and lifetime, and has limited the widespread adoption of these grid-scale energy storage technologies. Poor charge transfer and high interfacial resistance between molten sodium and solid-state electrolytes, however, prevents the operation of molten sodium batteries at low temperatures. In this study, in situ formation of tin-based chaperone phases on solid state NaSICON ion conductor surfaces is shown in this work to greatly improve charge transfer and lower interfacial resistance in sodium symmetric cells operated at 110 °C at current densities up to an aggressive 50 mA cm –2 . It is shown that static wetting testing, as measured by the contact angle of molten sodium on NaSICON, does not accurately predict battery performance due to the dynamic formation of a chaperone NaSn phase during cycling. This work demonstrates the promise of sodium intermetallic-forming coatings for the advancement of low temperature molten sodium batteries by improved mating of sodium–NaSICON surfaces and reduced interfacial resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Stabilization of garnet/Li interphase by diluting the electronic conductor

The high interfacial resistance and lithium (Li) dendrite growth are two major challenges for solid-state Li batteries (SSLBs). The lack of understanding on the correlations between electronic conductivity and Li dendrite formation limits the success of SSLBs. Here, by diluting the electronic conductor from the interphase to bulk Li during annealing of the aluminium nitride (AlN) interlayer, we changed the interphase from mixed ionic/electronic conductive to solely ionic conductive, and from lithiophilic to lithiophobic to fundamentally understand the correlation among electronic conductivity, Li dendrite, and interfacial resistance. During the conversion-alloy reaction between AlN and Li, the lithiophilic and electronic conductive Li x Al diffused into Li, forming a compact lithiophobic and ionic conductive Li 3 N, which achieved an ultrahigh critical current density of 2.6/14.0 mA/cm 2 in the time/capacity-constant mode, respectively. The fundamental understanding on the effect of interphase nature on interfacial resistance and Li dendrite suppression will provide guidelines for designing high-performance SSLBs.

25 ENERGY STORAGE↗
DOE OSTI2025

High-heat transfer lithium-ion batteries: A new era in battery thermal management

Despite advances in lithium-ion battery technology, critical challenges remain that must be addressed to accelerate electric vehicle (EV) adoption and global energy transformation. Significantly improved battery thermal management (BTM) is key to overcoming these challenges. BTM approaches focus on increasing heat transfer coefficients via air, liquid, or refrigerant cooling, but less attention is given to reducing the battery's thermal resistance, a major bottleneck for heat transfer. This work introduces a novel approach to reduce battery thermal resistance by integrating in-plane heat transfer with optimized cell geometry, minimized thermal resistances, and reduced interfacial resistances, representing a departure from previous methods. The standard prismatic can cell incorporating this technology is referred to as the high heat transfer (HHT) battery. An equivalent resistance battery thermal model is developed for speed and accuracy, validated against experimental data in the literature, demonstrating strong correlation and ensuring reliable predictions for real-world performance. Thermal performance metrics of the conventional and HHT batteries are compared using a parametric study with air, liquid, and refrigerant boundary conditions across a range of aspect ratios. The HHT battery shows a heat removal rate up to 20 times higher than a conventional battery. These findings suggest that HHT technology could be transformative for EV battery performance, enabling fast charging, mitigating thermal runaway, extending battery life, reducing cold-weather power loss, increasing reliability, lowering costs, and enabling higher energy density, all critical for EV adoption and energy transformation. Future work will focus on prototyping and real-world testing to refine these findings for commercial-scale applications.

25 ENERGY STORAGE↗
NASA NTRS1989

Monolithic Solid Oxide Fuel Cell development

The Monolithic Solid Oxide Fuel Cell (MSOFC) is an oxide-ceramic structure in which appropriate electronic and ionic conductors are fabricated in a honeycomb shape similar to a block of corrugated paperboard. These electronic and ionic conductors are arranged to provide short conduction paths to minimize resistive losses. The power density achievable with the MSOFC is expected to be about 8 kW/kg or 4 kW/L, at fuel efficienceis over 50 percent, because of small cell size and low resistive losses in the materials. The MSOFC operates in the range of 700 to 1000 C, at which temperatures rapid reform of hydrocarbon fuels is expected within the nickel-YSZ fuel channels. Tape casting and hot roll calendering are used to fabricate the MSOFC structure. The performance of the MSOFC has improved significantly during the course of development. The limitation of this system, based on materials resistance alone without interfacial resistances, is 0.093 ohm-sq cm area-specific resistance (ASR). The current typical performance of MSOFC single cells is characterized by ASRs of about 0.4 to 0.5 ohm-sq cm. With further development the ASR is expected to be reduced below 0.2 ohm-sq cm, which will result in power levels greater than 1.4 W/sq cm. The feasibility of the MSOFC concept was proven, and the performance was dramatically improved. The differences in thermal expansion coefficients and firing shrinkages among the fuel cell materials were minimized. As a result of good matching of these properties, the MSOFC structure was successfully fabricated with few defects, and the system shows excellent promise for development into a practical power source.

Myles, K. M.↗
NASA NTRS1988

Experiences in extraction of contact parameters from process-evaluation test-structures

Six-terminal-contact test structures are introduced for characterizing ohmic contacts between a metal and a heavily doped semiconductor layer. Specifically, the six-terminal test structure supplies the additional information needed in order to calculate the transmission length and eventual corrections to the characteristic resistance per unit width due to finite contact length. The essential feature of this test structure is a square contact with four taps in the lower (semiconductor) layer. Every other one of these taps is used for current injection ('front'). From the voltage drop at the opposite tap and the side taps, the 'end' resistance and the 'side' resistances are calculated. The test structures are shown to give valuable information complementary to the common front resistance measurements. The interfacial resistivity is obtained directly after proper correction for flange effects.

Lieneweg, Udo↗
DOE OSTI2026

Particle‐Size‐Dependent Lithium‐Ion Transport in PEO/LLZO Composite Electrolytes

Lithium-metal batteries with solid electrolytes can deliver higher energy density and improved safety than conventional Li-ion batteries. Among solid electrolyte candidates, polymer/ceramic composite electrolytes are attractive because they combine polymer flexibility with the high ionic conductivity of ceramics. However, whether ceramic fillers synergistically reduce polarization losses in the polymer matrix remains unclear. A central unknown is the critical polymer/ceramic interfacial resistance (Rint,crit), below which adding ceramics lowers electrolyte overpotential. Here, we present the first macroscale model framework to quantify R int,crit for composite electrolytes based on polyethylene oxide (PEO) and Ta-doped Li 7 La 3 Zr 2 O 12 (LLZO). A 1D model for DC-polarization of tri-layer cells (PEO-LiTFSI/LLZO/PEO-LiTFSI) shows that LLZO surface functionalization reduces the PEO/LLZO interfacial resistance, consistent with electrochemical impedance measurements. Extending to a 2D composite model, we show notably that Rint,crit scales linearly with LLZO particle diameter and shifts toward experimentally accessible values (e.g., 28.8 Ωcm 2 ) as particle size increases. At fixed ceramic volume fraction, larger LLZO particles reduce the number of interfacial crossings, driving more current through the ceramic phase and lowering concentration polarization. In contrast, R int,crit is largely independent of ceramic volume fraction. These results demonstrate that ceramic filler-size engineering can enable synergistic, energy-efficient transport in polymer/ceramic composite electrolytes.

25 ENERGY STORAGE↗