Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interfacial evaporation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Optimization of Delignified Wood Rods for Interfacial Solar Evaporation

Interfacial solar evaporation using three-dimensional evaporator materials has shown promise to achieve high evaporation rates exceeding the photothermal limit for water treatment and resource recovery processes. However, challenges remain in optimizing the material geometry to balance the vertical capillary uptake of water and the rate of evaporation to achieve both stable and high evaporation rates. Delignified wood can serve as a highly porous and hydrophilic substrate material to achieve high evaporation rates. In this work, we designed a suspended biochar-coated delignified wood rod evaporator and investigated the influence of its geometric parameters on its evaporation performance. The height of the evaporator exposed to air for evaporation was observed to be an important parameter in governing the evaporation rate, as shorter evaporators limited the available surface area for evaporation, but taller evaporators could not achieve sufficient rates of capillary uptake to maintain stable evaporation rates over 24 h under 1-sun illumination (1 kW m –2 ). In conclusion, the exposed height of the evaporator was optimized to achieve an average hourly evaporation rate of 3.05 ± 0.23 kg m –2 h –1 , which could be maintained in saline solutions containing up to 5 wt % NaCl.

Coating materials↗
DOE OSTI2021

Interfacial Solar Evaporation by a 3D Graphene Oxide Stalk for Highly Concentrated Brine Treatment

In this study, we demonstrate a 3-dimensional graphene oxide (3D GO) stalk that operates near the capillary wicking limit to achieve an evaporation flux of 34.7 kg m -2 h -1 under 1 sun conditions (1 kW/m 2 ). This flux represents nearly a 100 times enhancement over a conventional solar evaporation pond. Interfacial solar evaporation traditionally uses 2D evaporators to vaporize water using sunlight, but their low evaporative water flux limits their practical applicability for desalination. Some recent studies using 3D evaporators demonstrate potential for more efficient water transfer, but the flux improvement has been marginal because of a low evaporation area index (EAI), which is defined as the ratio of the total evaporative surface area to the projected ground area. By using a 3D GO stalk with an ultrahigh EAI of 70, we achieved nearly a 20-fold enhancement over a 2D GO evaporator. The 3D GO stalk also exhibited additional advantages including omnidirectional sunlight utilization, a high evaporation flux under dark conditions from more efficient utilization of ambient heating, a dramatic increase of the evaporation rate by introducing wind, and scaling resistance in evaporating brines with a salt content of up to 17.5 wt %. This performance makes the 3D GO stalk well suited for the development of a low-cost, reduced footprint technology for zero liquid discharge in brine management applications.

3D evaporator↗
DOE OSTI2025

Mineral Scaling in 3D Interfacial Solar Evaporators–A Challenge for Brine Treatment and Lithium Recovery

In this work, we analyzed the effects of mineral scaling on the performance of a 3D interfacial solar evaporator, with a focus on the cations relevant to lithium recovery from brackish water. The field has been rapidly moving toward resource recovery applications from brines with higher cation concentrations. However, the potential complications caused by common minerals in these brines other than NaCl have been largely overlooked. Therefore, in this study, we thoroughly examined the effects of two common cations (calcium and magnesium) on the long-term solar evaporation performance of a 3D graphene oxide stalk. The 3D stalk can achieve an evaporation flux as high as 17.8 kg m –2 h –1 under one-sun illumination, and accumulation of NaCl on the stalk surface has no impact. However, the presence of CaCl 2 and MgCl 2 significantly reduces the evaporative flux even in solutions lacking scale-forming anions. A close examination of scale formation during long-term evaporation experiments revealed that CaCl 2 and MgCl 2 tend to precipitate out within the stalk, thus blocking water transport through the stalk and significantly dropping the evaporation rates. These findings imply that research attention is needed to modify and optimize the internal water transport channels for 3D evaporators. Additionally, we emphasize the importance of testing realistic mixtures–including prominent divalent cations– and testing long-term operations in interfacial solar evaporation research and investigating approaches to mitigate the negative impacts of divalent cations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Seawater Desalination Derived Entirely from Ocean Biomass

Solar-driven interfacial evaporation shows great prospects for seawater desalination with its rapid fast evaporation rate and high photothermal conversion efficiency. Here, a sustainable, biodegradable, non-toxic, and highly efficient full ocean biomass-based solar-driven evaporator is reported, which is composed of chitosan (CS) hydrogel as the hydratable skeleton and cuttlefish ink (CI) as the photothermal material. Under solar irradiation, the cuttlefish ink powder harvests solar energy and heats the surrounding water. Simultaneously, the water in the three-dimensional network of chitosan hydrogel is rapidly replenished by the interconnected porous structure and the hydrophilic functional groups attached to the polymer chains. With its enlarged evaporation surface, high solar absorptance, adequate water transportation, good salt drainage, and heat localization, the CI/CS-based evaporator achieves a remarkable evaporation rate of 4.1 kg m-2 h-1 under one sun irradiance (1 kW m-2) with high-quality freshwater yields. This full ocean biomass-based evaporator with abundant raw material availability provides new possibilities for an efficient, stable, sustainable, and environmentally friendly solar evaporator with guaranteed water quality.

BIOMASS FUELS,INORGANIC, ORGANIC, PHYSICAL, AND AN↗
NASA NTRSDate not supplied

The ZBOT-NC Experiment - Effects of Non-Condensable Gases on Propellant Tank Pressurization and Pressure Control

Introduction Integral to all phases of NASA’s projected planetary expeditions is affordable and reliable cryogenic fluid storage for use in propellant or life support systems. It is greatly advantageous to develop innovative vent-less pressure control designs based on cooling/mixing of the bulk tank fluid to allow storage of the cryogenic fluid with zero or reduced boil-off. The presence of noncondensable gases, can interfere with the condensation at the interface impacting tank pressure control during subcooled jet mixing especially in microgravity. The Zero-Boil-Off Tank (ZBOT) Experiments are a series of small-scale experiments aboard the International Space Station (ISS) that use a transparent volatile simulant fluid in a transparent sealed tank to delineate various fundamental fluid flow, heat and mass transport, and phase change phenomena associated with storage tank pressurization and pressure control in microgravity. The ZBOT-1 experiment was performed on the ISS 2017-2018 timeframe and collected data to validate a state-of-the-art CFD model for tank pressurization and pressure control for a pure system. The ZBOT-NC Experiment is the second experiment in the series to be performed on the International Space Station (ISS) in 2025. Its goal is to investigate the effects of noncondensable gases on interfacial evaporation and condensation during self -pressurization and jet-mixing pressure control in microgravity for a two-component system. Materials & Methods In this work, we will describe the detailed features of the ZBOT-NC experimental hardware and Diagnostics that includes nonintrusive Quantum Dot Thermometry (QDT) for whole field temperature measurement. All microgravity pressurization and pressure control tests will be performed for both the pure and the two-components systems with Xenon and Neon as the two noncondensable gases spanning small and large molecular weights and sizes. The two-phase CFD model that is developed as part of the project will be also presented and discussed. Results Ground-based pressurization and jet mixing experiments and CFD simulation results are compared to each other to validate both the fidelity of the CFD model predictions and the accuracy of the QDT measurement. Model simulations for noncondensable gas effects will also be compared against large Cryogenic LH2-GHe experiments to indicate the noncondensable gas effects on tank pressure control during jet mixing in 1G. Finally, CFD results will be presented to predict the effects of the noncondensable gas during subcooled jet mixing during the ZBOT-NC in advance of the microgravity experiment in 2015.

Evaporation Condensation↗
NASA NTRSDate not supplied

The Zero-Boil-Off Tank Experiment: the Effects of Non-Condensable Gases on Pressurization and Pressure Control of Propellant Tanks in Microgravity

Introduction Integral to all phases of NASA’s projected planetary expeditions is affordable and reliable cryogenic fluid storage for use in propellant or life support systems. It is greatly advantageous to develop innovative vent-less pressure control designs based on cooling/mixing of the bulk tank fluid to allow storage of the cryogenic fluid with zero or reduced boil-off. The presence of noncondensable gases, can interfere with the condensation at the interface impacting tank pressure control during subcooled jet mixing especially in microgravity. The Zero-Boil-Off Tank (ZBOT) Experiments are a series of small-scale experiments aboard the International Space Station (ISS) that use a transparent volatile simulant fluid in a transparent sealed tank to delineate various fundamental fluid flow, heat and mass transport, and phase change phenomena associated with storage tank pressurization and pressure control in microgravity. The ZBOT-1 experiment was performed on the ISS 2017-2018 timeframe and collected data to validate a state-of-the-art CFD model for tank pressurization and pressure control for a pure system. The ZBOT-NC Experiment is the second experiment in the series to be performed on the International Space Station (ISS) in 2025. Its goal is to investigate the effects of noncondensable gases on interfacial evaporation and condensation during self -pressurization and jet-mixing pressure control in microgravity for a two-component system. Materials & Methods In this work, we will describe the detailed features of the ZBOT-NC experimental hardware and Diagnostics that includes nonintrusive Quantum Dot Thermometry (QDT) for whole field temperature measurement. All microgravity pressurization and pressure control tests will be performed for both the pure and the two-components systems with Xenon and Neon as the two noncondensable gases spanning small and large molecular weights and sizes. The two-phase CFD model that is developed as part of the project will be also presented and discussed. Results Ground-based pressurization and jet mixing experiments and CFD simulation results are compared to each other to validate both the fidelity of the CFD model predictions and the accuracy of the QDT measurement. Model simulations for noncondensable gas effects will also be compared against large Cryogenic LH2-GHe experiments to indicate the noncondensable gas effects on tank pressure control during jet mixing in 1G. Finally, CFD results will be presented to predict the effects of the noncondensable gas during subcooled jet mixing during the ZBOT-NC in advance of the microgravity experiment in 2015.

Evaporation Condensation↗
DOE OSTI2020

Integrated Evaporator for Efficient Solar-Driven Interfacial Steam Generation

Solar-driven interfacial steam generation is a promising technique for clean water production as it can minimize thermal loss by localizing solar-to-heat conversion at the air/liquid interface. Here we report an integrated solar-evaporator by partially growing two-dimensional polypyrrole microsheets within a melamine foam through chemical vapor polymerization. These microsheets can induce multiple light reflections within the foam, enable omnidirectional light absorption, provide abundant surfaces to promote heat transfer, and achieve spatially-defined hydrophobicity to facilitate vapor escape. Meanwhile, the inherent hydrophilicity of the bottom part of the foam promotes spontaneous upward water transport and suppresses heat loss. The composite foam exhibits an excellent apparent evaporation rate of ~2 kg/(m 2 ·h) and solar-to-vapor efficiency of ~91%. Here, the combined advantages of large surface area, high efficiency, low cost, all weather application, excellent durability, and scalable manufacturing make our integrated design promising for fabricating large-scale solar steam generation systems that are suitable for practical clean water production.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Theory of the photomolecular effect

It is well-known that water in liquid and vapor phases exhibits weak visible-light absorption. Recent experiments, however, show that at the liquid-air interface, absorption drastically increases, accelerating evaporation beyond thermal limits by 2–5 times. Strikingly, evaporation peaks at green wavelengths, despite no corresponding absorptance peak. The underlying mechanism of this observation, termed the photomolecular effect, remains puzzling, particularly as water molecules do not exhibit resonance peaks in the visible spectrum. Here, we present a theoretical model explaining the effect. We show that surface-bound water clusters undergo non-resonant photon-driven evaporation, with green light being particularly effective. Crucially, we do not expect green light to couple more strongly than other wavelengths to the molecules at the surface, rather the energy of green light is more effectively used to vaporize water. Our model accounts for why the evaporation peak does not align with absorptance and provides a quantum mechanical explanation of how a single photon can vaporize an entire molecular cluster. This model challenges conventional views on water-light interactions, revealing a fundamentally non-thermal evaporation mechanism. Furthermore, our findings have implications for water purification, energy-efficient drying, and climate modeling, opening new pathways for optimizing evaporation-based technologies.

Interfacial evaporation↗
DOE OSTI2023

A conservative, interface-resolved, compressible framework for the modeling and simulation of liquid/gas phase change

This paper presents a method for simulating evaporation in a compressible, interface-resolved framework appropriate for modeling problems of engineering interest. In order to achieve robustness and broad applicability, the method has been designed to discretely enforce consistent mass and thermal energy transport at the phase interface, to globally conserve mass, momentum, and energy, and to be capable of modeling compressible and incompressible systems. Verification is performed via the Sod-shock test, one-dimensional heat conduction, evaporation from a planar interface, and evaporation of three-dimensional droplets. Convergence with increasing mesh resolution is demonstrated in all tested configurations, and conservation is maintained near machine precision for a translating droplet. Conservation and accurate phase change rates are preserved at the low numerical resolutions commonly encountered in engineering calculations. Following verification, the method is validated by comparison to an empirical correlation for evaporating droplets in high temperature crossflow, and the presentation concludes with the simulation of an iso-octane spray at conditions representative of gasoline direct injection. In conclusion, successful verification, validation, and demonstrated practical utility suggest the method to be an accurate, efficient, and robust approach for the study of phase change in engineering systems.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1981

Improved adhesion of Ni films on X-ray damaged polytetrafluoroethylene

The considered investigation shows that the adhesion of evaporated Ni on polytetrafluoroethylene (PTFE) is enhanced by irradiating the PTFE surface prior to evaporation. Evidence obtained with the aid of X-ray photoelectron spectroscopy is presented concerning the association of the enhanced adhesion with an interfacial chemical reaction. Evaporated Ni clearly adheres better to the X-ray damaged PTFE surface than to the undamaged surface. There is evidence that the improved adhesion is not related to the Ni-C bond, but rather to the NiF2. A possible mechanism which may be consistent with the data is the formation of a F-Ni-C complex, where C is a member of the polymer chain.

Wheeler, D. R.↗
DOE OSTI2020

An implicit, sharp numerical treatment of viscous terms at arbitrarily shaped liquid-gas interfaces in evaporative flows

We report a novel methodology for accurate treatment of viscous terms in evaporation problems. The proposed scheme is an extension of the sharp viscous treatment of Kang et al. (2000) [7] to 3D phase change problems. To ensure accuracy and grid converging solutions, a new implicit approach to computing viscous fluxes across the phase interfaces is proposed, which was previously unavailable in fixed grid numerical schemes. Analytical relations were derived for the jump in velocity gradients across the 2D and 3D phase interfaces, an important constituent of the proposed scheme. The relations show a non-vanishing jump in the tangential gradients across the phase interface that are associated with evaporative flux and interfacial curvature. The proposed methodology demonstrated first order accuracy in canonical test cases. It is general and applicable to arbitrarily oriented interfaces, and can be readily implemented in existing evaporation flow solvers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRSDate not supplied

Modeling Self-Pressurization and Spray Bar Pressure Control of a Cryogenic Storage Tank in Normal Gravity

This paper presents Computational Fluid Dynamics (CFD) models for simulating self-pressurization and spray bar cooling processes in a large-scale liquid hydrogen storage tank under normal gravity. The self-pressurization model utilizes the kinetics-based Schrage equation with the Volume-Of-Fluid (VOF) model to account for the evaporative and condensing interfacial mass fluxes. It uses a laminar approach to model natural convection and compares the pressures and temperatures predicted by the CFD model with experimental data from the Multipurpose Hydrogen Test Bed (MHTB) self-pressurization experiment. Additionally, the predicted interfacial mass flux is presented. A CFD model for simulating pressure control using a spray bar is also presented. An Eulerian-Lagrangian approach models the interactions between the discrete droplets and the continuous ullage phase. The spray model is coupled with the VOF model by tracking particles in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. The T-sat model is used to calculate the droplet-ullage heat and mass transfer. In this model, droplets warm up to the saturation temperature corresponding to the ullage vapor pressure thereafter evaporating while remaining at the saturation temperature. The tank pressure, vapor, and liquid temperature evolutions are validated against data from the MHTB spray bar mixing experiment.

Self-Pressurization↗
NASA NTRS2014

Self-Pressurization and Spray Cooling Simulations of the Multipurpose Hydrogen Test Bed (MHTB) Ground-Based Experiment

This paper presents a CFD (computational fluid dynamics) model for simulating the self-pressurization of a large scale liquid hydrogen storage tank. In this model, the kinetics-based Schrage equation is used to account for the evaporative and condensing interfacial mass flows. Laminar and turbulent approaches to modeling natural convection in the tank and heat and mass transfer at the interface are compared. The flow, temperature, and interfacial mass fluxes predicted by these two approaches during tank self-pressurization are compared against each other. The ullage pressure and vapor temperature evolutions are also compared against experimental data obtained from the MHTB (Multipuprpose Hydrogen Test Bed) self-pressurization experiment. A CFD model for cooling cryogenic storage tanks by spraying cold liquid in the ullage is also presented. The Euler- Lagrange approach is utilized for tracking the spray droplets and for modeling interaction between the droplets and the continuous phase (ullage). The spray model is coupled with the VOF (volume of fluid) model by performing particle tracking in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. Droplet ullage heat and mass transfer are modeled. The flow, temperature, and interfacial mass flux predicted by the model are presented. The ullage pressure is compared with experimental data obtained from the MHTB spray bar mixing experiment. The results of the models with only droplet/ullage heat transfer and with heat and mass transfer between the droplets and ullage are compared.

cryogenic fluid storage↗
NASA NTRS1975

Interfacial impurities and the reaction between Si and evaporated Al

As commonly formed, the interface between substrate Si and evaporated Al is laden with impurities. Subsequent heating causes modest dissolution of Si into solid Al, the dissolution morphology being influenced by the interface impurities. In the present experiments, the amount of Si dissolving was considerably enhanced, causing sufficient interface movement to carry most interfaces clear of the original impurities. Under these conditions, the Si/Al interface assumes, during brief heat treatment, a simple shape composed of a few 111 plane-type facets. Such Si/Al interfaces produced in situ should be useful for low-temperature solid-state growth of Si.

Best, J. S.↗
DOE OSTI2022

Numerical simulation of evaporating wavy falling liquid films in laminar gas streams

Numerical simulations are performed to investigate the interfacial heat and mass transfer from evaporating wavy falling liquid films in interaction with laminar gas streams. The OpenFOAM solver has been used to conduct the simulations where the liquid-gas interface is resolved using the Volume of Fluid method of solving for three phases, i.e., liquid, vapor, and air. The configuration considered is a falling liquid (water) film on a heated vertical plate with a confined laminar moist air (gas) flow that is either (a) co-current or (b) counter-current to the downward liquid flow. The evaporation at the liquid-gas interface is driven by the interfacial gradient of the vapor mass fraction. Interfacial waves are triggered using a monochromatic forcing disturbance that leads to sinusoidal or solitary waves forming at the liquid-gas interface under respective forcing frequencies. Further, the numerical model is validated with the available experimental data. The results show nearly a 15% enhancement in time-averaged Sherwood number (Sh) due to film waviness (sinusoidal or solitary) at the lower volumetric gas flow rate, Q g = +50 (co-current) and Q g = -50 (counter-current). This enhancement in the Sh for both the waves further increases by 11% with Q g = +800 and 196% with Q g = -800. A closer examination of the mass transfer process over a wave demonstrates that with Q g = +50, the concentration of the gas side streamlines at the trough locations of the wave leads to higher values of Sh at these locations. However, with Q g = +800, although the overall Sh increases, vortices appear at the wave trough locations, leading to a corresponding decrease in the local Sh values. Correlations are proposed for predicting Sh under co-current and counter-current gas flow effects.

36 MATERIALS SCIENCE↗
NASA NTRS2015

CFD Modeling of the Multipurpose Hydrogen Test Bed (MHTB) Self-Pressurization and Spray Bar Mixing Experiments in Normal Gravity: Effect of the Accommodation Coefficient on the Tank Pressure

A CFD model for simulating the self-pressurization of a large scale liquid hydrogen storage tank is utilized in this paper to model the MHTB self-pressurization experiment. The kinetics-based Schrage equation is used to account for the evaporative and condensi ng interfacial mass flows in this model. The effect of the accommodation coefficient for calculating the interfacial mass transfer rate on the tank pressure during tank selfpressurization is studied. The values of the accommodation coefficient which were considered in this study vary from 1.0e-3 to 1.0e-1 for the explicit VOF model and from 1.0e-4 to 1.0e-3 for the implicit VOF model. The ullage pressure evolutions are compared against experimental data. A CFD model for controlling pressure in cryogenic storage tanks by spraying cold liquid into the ullage is also presented. The Euler-Lagrange approach is utilized for tracking the spray droplets and for modeling the interaction between the droplets and the continuous phase (ullage). The spray model is coupled with the VOF model by performing particle tracking in the ullage, removing particles from the ullage when they reach the interface, and then adding their contributions to the liquid. Droplet-ullage heat and mass transfer are modeled. The flow, temperature, and interfacial mass flux, as well as droplets trajectories, size distribution and temperatures predicted by the model are presented. The ul lage pressure and vapor temperature evolutions are compared with experimental data obtained from the MHTB spray bar mixing experiment. The effect of the accommodation coefficient for calculating the interfacial and droplet mass transfer rates on the tank pressure during mixing of the vapor using spray is studied. The values used for the accommodation coefficient at the interface vary from 1.0e-5 to 1.0e-2. The droplet accommodation coefficient values vary from 2.0e-6 to 1.0e-4.

cryogenic fluid storage↗
DOE OSTI2020

Vaporizable endoskeletal droplets via tunable interfacial melting transitions

Liquid emulsion droplet evaporation is of importance for various sensing and imaging applications. The liquid-to-gas phase transformation is typically triggered thermally or acoustically by low–boiling point liquids, or by inclusion of solid structures that pin the vapor/liquid contact line to facilitate heterogeneous nucleation. However, these approaches lack precise tunability in vaporization behavior. Here, we describe a previously unused approach to control vaporization behavior through an endoskeleton that can melt and blend into the liquid core to either enhance or disrupt cohesive intermolecular forces. This effect is demonstrated using perfluoropentane (C 5 F 12 ) droplets encapsulating a fluorocarbon (FC) or hydrocarbon (HC) endoskeleton. FC skeletons inhibit vaporization, whereas HC skeletons trigger vaporization near the rotator melting transition. Our findings highlight the importance of skeletal interfacial mixing for initiating droplet vaporization. Tuning molecular interactions between the endoskeleton and droplet phase is generalizable for achieving emulsion or other secondary phase transitions, in emulsions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗