Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface chemistry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Dominance of interface chemistry over the bulk properties in determining the electronic structure of epitaxial metal/perovskite oxide heterojunctions

We show that despite very similar crystallographic properties and work function values in the bulk, epitaxial Fe and Cr metallizations on Nb:SrTiO3(001) generate completely different heterojunction electronic properties. Cr is Ohmic whereas Fe forms a Schottky barrier with a barrier height of 0.50 eV. This contrast arises because of differences in interface chemistry. In contrast to Cr [Chambers, S. A. et al., Adv. Mater. 2013, 25, 4001.], Fe exhibits a +2 oxidation state and occupies Ti sites in the perovskite lattice, resulting in negligible charge transfer to Ti, upward band bending, and Schottky barrier formation. The differences between Cr and Fe are understood by performing first-principles calculations of the energetics of defect formation which corroborate the observed interface chemistry and structure.

Environmental Molecular Sciences Laboratory↗

Operando APXPS for direct probing of Li ion battery LCO electrode/electrolyte interface chemistry during lithiation/delithiation

The real-time interface chemistry between the lithium cobalt oxide (LCO) working electrode and the LiClO 4 /propylene carbonate (PC) electrolyte is investigated during lithiation/delithiation using dip-and-pull ambient pressure photoelectron spectroscopy (APXPS). The APXPS results appear to exhibit the seldom discussed Co 2+ state in the LCO structure, where the operando measurements indicate electron transfer among Co 2+ , Co 3+ , and Co 4+ states. Specifically, the lithiation of LCO reduces the Co 4+ state to both Co 3+ and Co 2+ states, where, as a function of voltage, reduction to the Co 2+ state is initially more pronounced followed by Co 3+ formation. In addition, a delay in surface delithiation is observed during the reverse potential steps. This is discussed in terms of overpotential at the interface measurement position as a consequence of the dip-and-pull setup for this experiment. Finally, the shifts in the apparent binding energies of the spectral features corresponding to the electrolyte and LCO at their interface show that the electrochemical potentials at delithiation voltage steps are different from the lithiation steps at the same applied voltages. This further explains the non-responsive delithiation. The BE shift observed from the LCO surface is argued to be dominantly due to the semi-conductive nature of the sample. Overall, this article shows the importance of operando APXPS for probing non-equilibrium states in battery electrodes for understanding electron transfer in the reactions.

Liu, Qianhui [Uppsala Univ. (Sweden)] (ORCID:00000↗

Tuning the Anode–Electrolyte Interface Chemistry for Garnet-Based Solid-State Li Metal Batteries

Lithium (Li) metal anode is a promising candidate for high energy density solid-state batteries. However, the interface issues, including large interfacial resistance and Li dendrite generation, have always frustrated the attempt to commercialize solid-state Li metal batteries (SSLBs). Here, we report that infusing the garnet-type solid electrolytes (GSEs) with air-stable electrolyte Li 3 PO 4 (LPO) dramatically reduces the interfacial resistance to ~1 Ω cm 2 and achieves a high critical current density of 2.2 mA cm -2 under ambient condition due to enhanced interfacial stability to Li metal anode. The coated and infused LPO electrolytes not only improve the mechanical strength and Li-ion conductivity of grain boundaries, but also form a stable Li-ion conductive but electron-insulating LPO-derived solid-electrolyte interphase between Li metal and GSEs, and consequently eliminates the Li dendrites growth and prevents the direct reduction of GSEs by Li metal over a long cycle life. This interface engineering approach together with grain-boundary modification on GSEs represents a promising strategy to revolutionize the anode-electrolyte interface chemistry for SSLBs and provides new design strategy for other-types of solid-state batteries.

25 ENERGY STORAGE↗

Ge/SrTiO{sub 3}(001): Correlation between interface chemistry and crystallographic orientation

In this work, the desorption of a submonolayer deposit of Ge on SrTiO{sub 3}(001) is studied by reflection high energy electron diffraction. The results are compared to those of a previous experiment done using soft x-ray photoelectron spectroscopy. Combining these techniques allows for correlating interface chemistry and crystal orientation, and for bringing clarifying elements concerning the competition between (111) and (001) crystal orientation typical for the semiconductor/perovskite epitaxial systems. Despite poor interface matching, (111)-oriented islands are stabilized at the expense of (001)-oriented islands due to the relatively low energy of their free facets. Such 'surface energy driven' crystallographic orientation of the deposit is enhanced by the low adhesion energy characteristic of the Ge/SrTiO{sub 3} system.

36 MATERIALS SCIENCE↗

Pyrite (001) Interface Chemistry is Controlled by a Sulfoxy Termination

Pyrite (FeS 2 ) is the most common sulfide mineral on Earth, forming through inorganic reactions in the crust and oceanic hydrothermal systems and via microbially driven processes in anaerobic sediments. The pyrite–water interface is the site of a wide range of adsorption and reaction processes in Earth systems including oxidation that dramatically affects the geochemistry of surface waters and influences global carbon and oxygen cycles. Mechanistic geochemical models of pyrite interfacial reactivity, however, are limited by the lack of experimentally derived atomistic structures of the reduced and reacting surfaces. Here, in this work, we reveal the atomic-scale structure of the pyrite (001)-water interface that forms at very low oxygen partial pressures, relevant to suboxic environments in Earth. The interface structure and surface speciation were obtained using the crystal truncation rod method supported by ambient-pressure photoelectron spectroscopy and density functional theory calculations. The surface is dominantly composed of disulfide groups bound to a single oxygen atom, forming a sulfoxy group that has no known molecular or bulk mineral analog. This surface is interpreted as the first step in the oxidative dissolution of pyrite. The sulfoxy group is readily protonated through surface acid–base reactions that alter the structure of interfacial water and the free energy of interfacial reactions. Surface iron sites are not oxidized. Surprisingly, this interface can likely develop in equilibrium with bulk pyrite in some reducing and acidic solutions. This termination is therefore likely representative of pyrite surfaces under a vast range of experimental, industrial and Earth conditions.

oxidation↗

Effect of ball-milling surfactants on the interface chemistry in hot-compacted SmCo5 magnets

Anisotropic SmCo5 nanoflakes prepared by high-energy ball-milling with surfactants have great potential in applications for high-performance nanocomposite magnets. For such "nanocomposite" applications, the surface structure and chemistry of nanoflakes are crucial for achieving high coercivity. In this study, hot-pressed samples from anisotropic SmCo5 nanoflakes, ball-milled with different surfactants, oleic acid (OA) and oleylamine (OY), were investigated. Interface layers between the SmCo5 nanoflakes were found to consist of samarium oxides and a soft magnetic Co phase. These surface layers contribute to the degradation of hard magnetic performance, which is confirmed by scanning transmission electron microscopy-energy dispersive X-ray spectroscopy analysis of the cross-section of a single flake ball-milled with OA. Samples milled with OY show a much thinner interface layer in compacted samples, which means that the surface degradation during ball-milling with OY is much less than that with OA. The results show clearly that the choice of proper surfactant and the control of processing parameters are the key factors for improving the surface condition of the nanoflakes and the resulting hard magnetic properties. (C) 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Li, WF↗

Applications of SPM to Studies of Mineral–Water Interface Chemistry

The scanning probe microscope (SPM) has been utilized in studies of solid surfaces for nearly four decades. With resolution as high as the single atom level, valuable information on the structure and other properties of solid surfaces can be obtained. One of the most exciting areas of application for the SPM is in the study of mineral–water interfaces where the chemical reactions taking place are both of fundamental interest as well as important from an environmental/geochemical perspective. In this article, the basic design of one type of SPM, the atomic force microscope (AFM), is introduced followed by an examination of the different levels of resolution that may be exploited to obtain fundamental information on kink, step, and surface microtopography from mineral surfaces immersed in reactive solutions. The examples of these particular applications highlight the influence of solution chemistry on the rates and mechanisms of mineral growth and dissolution reactions that are readily followed with in-situ AFM instrumentation.

Higgins, Steven↗

Effect of ion sputtering on interface chemistry and electrical properties of Au GaAs(100) Schottky contacts

The effects of sputtering n-type (100)GaAs with 1 to 5 keV argon ions have been studied in ultrahigh vacuum. Auger electron and X-ray photoelectron spectroscopies have been used to characterize the surface before and after sputtering. Gold Schottky contacts were prepared in situ to avoid contamination at the metal/semiconductor interface. The data show that sputtering depletes the surface in As, and the extent of depletion increased as the ion energy was increased. However, angular-resolved photoelectron data showed As was enriched on the outer atom layer by 5 keV but depleted by 1 keV Ar(+) sputtering. Current and capacitance versus voltage data showed that sputtering always lowered the Schottky barrier height and generally increased the ideality factor. However, the barrier height after 3 keV sputtering was higher than after 1 keV sputtering. Those effects are explained based on a combined effective work function model and creation of a donorlike surface damage layer. The donor layer was correlated with As depletion by sputtering. Deep level trap formation and annealing of sputtering effects were studied.

Wang, Y.-X.↗

A multiscale model to understand the interface chemistry, contacts, and dynamics during lithium stripping

A reversible Li-metal electrode, paired with a solid electrolyte, is critical for attaining higher energy density and safer batteries beyond the current lithium-ion cells. A stable stripping process may be even harder to attain as the stripping process will remove Li-atoms from the surface, and naturally reduce surface contact area, if not self-corrected by other mechanisms, such as diffusion and plastic deformation under an applied external stack pressure. Here, we capture these mechanisms occurring at multiple length- and time- scales, i.e., interface interactions, vacancy hopping, and plastic deformation, by integrating density functional theory (DFT) simulations, kinetic Monte Carlo (KMC), and continuum finite element method (FEM). By assuming the self-affine nature of multiscale contacts, we predict the steady-state contact area as a function of stripping current density, interface wettability, and stack pressure. We further estimate the exponential increase of overpotential due to contact area loss to maintain the same stripping current density. We demonstrate that a lithiophilic interface requires less stack pressure to reach the same steady-state contact area fraction than a lithiophobic interface. A “tolerable steady-state” contact area loss for maintaining stable stripping is estimated at 20 %, corresponding to a 10 % increase in overpotential. To constrain contact loss within the tolerance, the required stack pressure is 0.1, 0.5, and 2 times the yield strength of lithium metal for three distinct interfaces, lithiophilic Li/lithium oxide(Li2O), Li/lithium lanthanum zirconium oxide(LLZO), and lithiophoblic Li/lithium fluoride(LiF), respectively. The modeling results agree with experiments on the impact of the stack pressure quantitatively, while the discrepancy in stripping rate sensitivity is attributed to the simplifying interface interaction in our simulations. Overall, this multiscale simulation framework demonstrates the importance of electrochemical-mechanical coupling in understanding the dynamics of the Li/SE interface during stripping.

Feng, Min↗

Nanostructured ligament and fiber Al–doped Li 7 La 3 Zr 2 O 12 scaffolds to mediate cathode-electrolyte interface chemistry

In this study, scaffold structures of electrospun aluminum–substituted lithium lanthanum zirconate Li 7 La 3 Zr 2 O 12 (Al-LLZO) were synthesized and used as an additive in a LiNi 0.6 Mn 0.2 Co 0.2 O 2 composite cathode. The scaffolds were crystalized in the cubic phase after calcination at 700 °C. The Al-LLZO scaffold morphology was dependent on the precursor formulation (aqueous and dimethylformamide. The aqueous precursors resulted in scaffolds of densely coalesced ligaments, whereas the dimethylformamide precursors resulted in high–aspect ratio nanofiber scaffolds. The long-term cycling stability and rate performance of the cells were found to depend on the Al-LLZO scaffold morphology. The uniformly dispersed Al-LLZO fibers resulted in a more stable cathode electrolyte interface formation through the reduced decomposition of the LiPF 6 salt during cycling, resulting in a better high-rate and long-term cycling performance.

25 ENERGY STORAGE↗

Structure and interface chemistry of MoO{sub 3} back contacts in Cu(In,Ga)Se{sub 2} thin film solar cells

Molybdenum oxide (MoO{sub 3}) is considered as a possible primary back contact for Cu(InGa)Se{sub 2} thin film solar cells for its potential as a transparent back contact for superstrate and bifacial devices. MoO{sub 3} films were deposited on Mo or ITO-coated soda lime glass substrates by reactive rf sputtering in an ambient of Ar + O{sub 2} with O{sub 2}/(O{sub 2} + Ar) = 35% on which Cu(In{sub 0.7}Ga{sub 0.3})Se{sub 2} alloy absorber layers were deposited using multi-source elemental evaporation. Scanning Electron Microscopy studies showed uniform coverage of the as-deposited MoO{sub 3} layer and good adhesion was obtained in all cases. X-ray Photoelectron Spectroscopy depth profile analysis showed that MoSe{sub 2} was not formed at the Cu(InGa)Se{sub 2} interface with either the Mo-MoO{sub 3} or ITO-MoO{sub 3} back contacts. Determination of the valence band offsets showed that the MoO{sub 3} layer at the interface changes the energy band alignment with Cu(InGa)Se{sub 2}, producing a primary contact with lower valence band offset than ITO. Cu(In,Ga)Se{sub 2} thin film solar cells prepared using an as-deposited Mo-MoO{sub 3} back contact yielded a best conversion efficiency of 14%, with V{sub OC} = 647 mV, J{sub SC} = 28.4 mA/cm{sup 2}, and FF = 78.1%. Cells with ITO-MoO{sub 3} back contact showed a best efficiency of 12%, with V{sub OC} = 642 mV, J{sub SC} = 26.8 mA/cm{sup 2}, and FF = 69.2%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tungsten Incorporation into Gallium Oxide: Crystal Structure, Surface and Interface Chemistry, Thermal Stability and Interdiffusion

Tungsten (W) incorporated gallium oxide (Ga2O3) (GWO) thin films were deposited by radio-frequency magnetron co-sputtering of W-metal and Ga2O3-ceramic targets. Films were produced by varying sputtering power applied to the W-target in order to achieve variable W-content (0-12 at%) into Ga2O3 while substrate temperature was kept constant at 500 °C. Chemical composition, chemical valence states, microstructure and crystal structure of as-deposited and annealed GWO films were evaluated as a function of W-content. The structural and chemical analyses indicate that the samples deposited without any W-incorporation are stoichiometric, nanocrystalline Ga2O3 films, which crystallize in β-phase monoclinic structure. While GWO films also crystallize in monoclinic β-Ga2O3 phase, W-incorporation induces surface amorphization as revealed by structural studies. The chemical valence state of Ga ions probed by X-ray photoelectron spectroscopic (XPS) analyses is characterized by the highest oxidation state i.e., Ga3+. No changes in Ga chemical state are noted for variable W-incorporation in the range of 0-12 at%. Rutherford backscattering spectrometry (RBS) analyses indicate the uniform distribution of W-content in the GWO films. However, XPS analyses indicate the formation of mixed valence states for W ions, which may be responsible for surface amorphization in GWO films. GWO films were stable up to 900 oC, at which point thermally induced secondary phase (W-oxide) formation was observed. A transition to mesoporous structure coupled with W interdiffusion occurs due to thermal annealing as derived from the chemical analyses at the GWO films’ surface as well as depth-profiling towards the GWO-Si interface. A model has been formulated to account for the mechanism of W-incorporation, thermal stability and interdiffusion via pore formation in GWO films.

Chemical composition↗

Role of Interface Chemistry in Opening New Radiative Pathways in InP/CdSe Giant Quantum Dots with Blinking-Suppressed Two-Color Emission

InP/CdSe core/thick–shell “giant” quantum dots (gQDs) that exhibit blinking–suppressed two–color excitonic emission have been synthesized and optically characterized. These type II heterostructures exhibit photoluminescence from both a charge–separated, near–infrared type II excitonic state, and a shell–localized visible–color excitonic state. Infrared emission is intrinsic to the type II QD, while visible emission can either be eliminated or enhanced through chemical modification of the InP surface prior to CdSe shell growth. Single–QD photoluminescence measurements confirm that the dual color emission is from individual nanocrystals. Here, the probability of observing dual emission from individual QDs and the extent of blinking suppression increases with shell thickness. Visible emission can be stabilized by the addition of a second shell of CdS, where the resulting InP/CdSe/CdS core/shell/shell nanocrystals afford the strongest blinking suppression, determined by analysis of the Mandel Q parameter. Transient absorption spectroscopy verifies that dual emission arises when hole relaxation from the shell to the core is impeded, possibly as a result of enhanced interfacial hole trapping at F – or O 2– defect sites. Electron–hole recombination in the shell then competes with slower type II recombination, providing a different mechanism for breaking Kasha's rule and allowing two colors of light to be emitted from one nanostructure.

36 MATERIALS SCIENCE↗

Interface chemistry informs about cathode and anode degradation during fast charging

Here, the aim of this study is to examine the development and makeup of the Solid Electrolyte Interphase (SEI) and Cathode Electrolyte Interphase (CEI) in lithium-ion batteries during rapid charging. Using X-ray photoelectron spectroscopy (XPS) and depth profiling, we investigate the chemical modifications occurring on the electrode surfaces during the initial formation and subsequent fast charge-discharge cycles. Our research shows that the anode's SEI initially comprises a thin layer rich in ketones, which then transforms into a thicker layer dominated by carbonaceous compounds during rapid charging cycles. Following assembly, lithium fluoride (LiF) quickly becomes a key element of the SEI, and its presence continues to grow substantially during the formation cycle, remaining the primary component throughout subsequent cycles. Initially, the cathode forms a thin oxide layer rich in ketones, with no noticeable carbonaceous CEI. The CEI primarily comprises LiF, which experiences an increase during the formation cycle and retains a thin layer of carbon coating after the initial rapid discharge. These findings show how the interphase layers impact the performance and stability of lithium-ion batteries, especially during fast charging for electric vertical take-off and landing (eVTOL) vehicles.

Fast charging↗

Engineered Interface Chemistry to Improve the Strength of Carbon Fiber Composites Cured by Electron Beam

A reactive sizing was designed to achieve high levels of interfacial adhesion and mechanical properties with a carbon fiber-acrylate system cured by electron beam (EB). The sizing was made of a partially cured epoxy sizing with a high density of pendant functional groups (acrylate functionality) able to generate a covalent bonding with the matrix. The interlaminar shear strength was clearly improved from 61 MPa to 81 MPa (+ 33 %) without any post-processing, reaching a similar value to the one obtained with the same system cured by a thermal treatment. Observation of the fracture profiles clearly highlighted a change in the fracture mechanism from a purely adhesive failure to a cohesive failure. Such improvements of the mechanical properties of carbon fiber composites cured by EB, without any post-cure, have not been reported previously to the best of our knowledge. This constitutes a breakthrough for the industrial development of composites EB curing.

acrylate↗

Addressing Soiling: From Interface Chemistry to Practicality

Natural soiling has reduced the energy output of photovoltaic (PV) systems since the technology was first used. Projecting even a small average annual soiling loss translates to billions of dollars in annual lost revenue worldwide. Production losses due to soiling can be very high in some locations, substantially increasing the levelized cost of electricity (LCOE) due to lost power production, increased operating and maintenance costs, and/or increased finance cost due to the uncertainty. Furthermore, although soiling has been discussed in the literature for more than 70 years, solutions to many problems are still needed. The National Renewable Energy Laboratory (NREL) is working with the PV industry to develop the tools/knowledge so that the effects of soiling can be predicted for different environmental conditions and cost-effective mitigation can be implemented. For this project, NREL performed a number of research and development tasks/subtasks in the following general areas to 1) predict PV module soiling losses based on environmental factors at a PV installation and from its energy production data, 2) quantitatively measure the adhesion forces to understand the physics enabling soiling, and 3) develop related standards on PV module coatings and artificial soiling. At the inception of the project, the PV industry considered these efforts to be the most important and immediate soiling issues that we could address to have the highest impact on LCOE. These focused efforts have led to outstanding accomplishments that have been communicated and very well received by the community.

14 SOLAR ENERGY↗