Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interactive materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Material interactions with the Low Earth Orbital (LEO) environment: Accurate reaction rate measurements

To resolve uncertainties in estimated LEO atomic oxygen fluence and provide reaction product composition data for comparison to data obtained in ground-based simulation laboratories, a flight experiment has been proposed for the space shuttle which utilizes an ion-neutral mass spectrometer to obtain in-situ ambient density measurements and identify reaction products from modeled polymers exposed to the atomic oxygen environment. An overview of this experiment is presented and the methodology of calibrating the flight mass spectrometer in a neutral beam facility prior to its use on the space shuttle is established. The experiment, designated EOIM-3 (Evaluation of Oxygen Interactions with Materials, third series), will provide a reliable materials interaction data base for future spacecraft design and will furnish insight into the basic chemical mechanisms leading to atomic oxygen interactions with surfaces.

Visentine, James T.↗
NASA NTRS1985

Material interactions with the low earth orbital environment Accurate reaction rate measurements

Interactions between spacecraft surfaces and atomic oxygen within the low earth orbital (LEO) environment have been observed and measured during Space Shuttle flights over the past 3 yr. The results of these experiments have demonstrated that interaction rates for many materials proposed for spacecraft applications are high and that protective coatings must be developed to enable long-lived operation of spacecraft structures in the LEO environment. A flight experiment discussed herein uses the Space Shuttle as an orbiting exposure laboratory to obtain accurate reaction rate measurements for materials typically used in spacecraft construction. An ion-neutral mass spectrometer, installed in the Orbiter cargo bay, will measure diurnal ambient oxygen densities while material samples are exposed at low altitude (222 km) to the orbital environment. From in situ atomic oxygen density information and postflight material recession measurements, accurate reaction rates can be derived to update the Space Station materials interaction data base. Additionally, gases evolved from a limited number of material surfaces subjected to direct oxygen impingement will be identified using the mass spectrometer. These measurements will aid in mechanistic definitions of chemical reactions which cause atom-surface interactions and in validating results of upcoming degradation studies conducted in ground-based neutral beam laboratories.

Visentine, J. T.↗
NASA NTRS1973

High temperature material interactions of thermoelectric systems using silicon germanium.

The efficient use of silicon germanium thermoelectric material for radioisotope thermoelectric generators (RTG) is achieved by operation at relatively high temperatures. The insulation technique which is most appropriate for this application uses multiple layers of molybdenum foil and astroquartz. Even so, the long term operation of these materials at elevated temperatures can cause material interaction to occur within the system. To investigate these material interactions, the Jet Propulsion Laboratory is currently testing a number of thermoelectric modules which use four silicon germanium thermoelectric couples in conjunction with the multifoil thermal insulation. The paper discusses the results of the ongoing four-couple module test program and correlates test results with those of a basic material test program.

Stapfer, G.↗
NASA NTRS1973

Materials interactions between the thermoelectric converter and the 5kwe reactor system

The integration of a compact thermoelectric converter with a 5-kwe reactor system is described. Material interaction uncertainties study is also presented. This includes degradation of the required austenitic - refractory metal transition joint during operation at high temperatures; loss of corrosion resistance; embrittlement by the presence of hydrogen; and loss of design margin by transport of interstitial elements. Analysis and limited experimental evidence indicate that these potential materials interactions can be adequately controlled. Group 5-2 refractory metals can be utilized without unacceptable adverse effect on system reliability.

Ferry, P. B.↗
NASA NTRS1981

High power densities from high-temperature materials interactions

Thermionic energy converters and metallic-fluid heat pipes are well suited to serve together synergistically. The two operating cycles appear as simple and isolated as their material problems seem forebodingly deceptive and complicated. Simplified equations verify material properties and interactions as primary influences on the operational effectiveness of both. Each experiences flow limitations in thermal emission and vaporization because of temperature restrictions redounding from thermophysicochemical stability considerations. Topics discussed include: (1) successful limitation of alkali-metal corrosion; (2) protection against external hot corrosive gases; (3) coping with external and internal vaporization; (4) controlling interfacial reactions and diffusion; and (5) meeting other thermophysical challenges; expansion matches and creep.

Morris, J. F.↗
NASA NTRS1981

High power densities from high-temperature material interactions

Thermionic energy conversion (TEC) and metallic-fluid heat pipes (MFHPs), offering unique advantages in terrestrial and space energy processing by virtue of operating on working-fluid vaporization/condensation cycles that accept great thermal power densities at high temperatures, share complex materials problems. Simplified equations are presented that verify and solve such problems, suggesting the possibility of cost-effective applications in the near term for TEC and MFHP devices. Among the problems discussed are: the limitation of alkali-metal corrosion, protection against hot external gases, external and internal vaporization, interfacial reactions and diffusion, expansion coefficient matching, and creep deformation.

Morris, J. F.↗
NASA NTRS1987

High power lasers: Sources, laser-material interactions, high excitations, and fast dynamics in laser processing and industrial applications; Proceedings of the Meeting, The Hague, Netherlands, Mar. 31-Apr. 3, 1987

The design and operation of high-power lasers for industrial applications are discussed in reviews and reports. Topics addressed include the status of optical technology in the Netherlands, laser design, the deposition of optical energy, laser diagnostics, nonmetal processing, and energy coupling and plasma formation. Consideration is given to laser-induced damage to materials, fluid and gas flow dynamics, metal processing, and manufacturing. Graphs, diagrams, micrographs, and photographs are provided.

Kreutz, E. W.↗
NASA NTRS2006

Material Interactions with Solar Wind Ion Environments

Solar wind composition is dominated by hydrogen (approx.96%) and helium (approx.3 to 4%) with a minor fraction (less than or equal to 1%) of heavy ions. Hydrogen (helium) ions impact spacecraft surfaces with energies from 0.5 to 5 keV (1.8 to 21 keV) due to variations in solar wind velocity from 300 km/s to 1000 km/sec with extremes of a few 10 s keV during periods of extremely high solar wind velocity exceeding 1000 km/sec. Mean impact energies are typically on the order of approximately 1 keV and 4 keV for hydrogen ions and helium ions, respectively. These energies are typically of the peak of the energy dependent light ion sputter yields for hydrogen and helium on many metals. In addition, light ions with kilovolt energies have been shown to produce blister (or exfoliation) damage to metal surfaces due to formation of high pressure gas bubbles within the materials when exposed to ion fluences on the order of 10(exp 16 to (10(exp 17 ions/sq cm. A number of spacecraft designs for current and future missions include gossamer polymer structures with thin metallic reflection coatings to shield instruments from the Sun or solar sail propulsion systems for use in a variety of locations in the inner solar system from 0.5 to 1 AU. In addition, there is interest in designing spacecraft for solar physics missions requiring operations as close to the Sun as 0.16 to 0.2 AU. Integrity of the metallic coatings is critical in many of these applications since degradation will result in modification of material thermal properties or exposure of polymers to solar UV photons which can compromise mission requirements. This paper will evaluate the relative contributions of sputtering and blister formation to material degradation in solar wind environments over a range of radial distances from the Sun to demonstrate where solar wind environments become important for materials selection. We will first review the physics and results from laboratory measurements of light ion sputtering, blistering, and exfoliation of metallic surfaces to establish the order of magnitude ion fluence required for significant surface damage. Solar wind ion fluence environments will then be evaluated due to variations in solar wind conditions as a function of solar cycle for varying distances from the Sun using models for radial variations in solar wind ion number density, temperature, and velocity to determine where sputtering and blistering is most likely to be an issue. Finally, ion fluence statistics for varying radial distances from the Sun will be shown to establish the mission duration and radial distances from the Sun where missions will encounter sufficient ion fluence to exhibit damage to metallic surfaces.

Minow, Joseph I.↗
NASA NTRS1994

Laboratory studies of fast oxygen atom interactions with materials

A pulsed 8 km/s oxygen atom source was used to perform a number of measurements of material interactions of interest to low Earth orbit applications. A system to measure the scattering distribution resulting from 8 km/s oxygen atoms impinging on selected spacecraft materials was developed. Data for scattering from glass and black and clear anodized aluminum are presented. Results on the fast atom oxidation mechanism for thin silver films, the O-atom velocity dependent erosion rates for selected materials, and the oxidation dependence on material temperature are presented.

Caledonia, George E.↗
NASA NTRS1989

Simulation of the low earth orbital atomic oxygen interaction with materials by means of an oxygen ion beam

Atomic oxygen is the predominant species in low-Earth orbit between the altitudes of 180 and 650 km. These highly reactive atoms are a result of photodissociation of diatomic oxygen molecules from solar photons having a wavelength less than or equal to 2430A. Spacecraft in low-Earth orbit collide with atomic oxygen in the 3P ground state at impact energies of approximately 4.2 to 4.5 eV. As a consequence, organic materials previously used for high altitude geosynchronous spacecraft are severely oxidized in the low-Earth orbital environment. The evaluation of materials durability to atomic oxygen requires ground simulation of this environment to cost effectively screen materials for durability. Directed broad beam oxygen sources are necessary to evaluate potential spacecraft materials performance before and after exposure to the simulated low-Earth orbital environment. This paper presents a description of a low energy, broad oxygen ion beam source used to simulate the low-Earth orbital atomic oxygen environment. The results of materials interaction with this beam and comparison with actual in-space tests of the same meterials will be discussed. Resulting surface morphologies appear to closely replicate those observed in space tests.

Banks, Bruce A.↗
NASA NTRS1972

Microphysical, microchemical and adhesive properties of lunar material. 3: Gas interaction with lunar material

Knowledge of the reactivity of lunar material surfaces is important for understanding the effects of the lunar or space environment upon this material, particularly its nature, behavior and exposure history in comparison to terrestrial materials. Adsorptive properties are one of the important techniques for such studies. Gas adsorption measurements were made on an Apollo 12 ultrahigh vacuum-stored sample and Apollo 14 and 15 N2-stored samples. Surface area measurements were made on the latter two. Adsorbate gases used were N2, A, O2 and H2O. Krypton was used for the surface area determinations. Runs were made at room and liquid nitrogen temperature in volumetric and gravimetric systems. It was found that the adsorptive/desorptive behavior was in general significantly different from that of terrestrial materials of similar type and form. Specifically (1) the UHV-stored sample exhibited very high initial adsorption indicative of high surface reactivity, and (2) the N2-stored samples at room and liquid nitrogen temperatures showed that more gas was desorbed than introduced during adsorption, indicative of gas release from the samples. The high reactivity is a scribed cosmic ray track and solar wind damage.

Grossman, J. J.↗
NASA NTRS1972

Microphysical, microchemical, and adhesive properties of lunar material. III - Gas interaction with lunar material.

Gas adsorption measurements on an Apollo 12 ultrahigh vacuum-stored sample and Apollo 14 and 15 N2-stored samples, show that the cosmic ray track and solar wind damaged surface of lunar soil is very reactive. Room temperature monolayer adsorption of N2 by the Apollo 12 sample at 0.0001 atm was observed. Gas evolution of Apollo 14 lunar soil at liquid nitrogen temperature during adsorption/desorption cycling is probably due to cosmic ray track stored energy release accompanied by solar gas release from depths of 100-200 nm.

Grossman, J. J.↗
NASA NTRS1995

Analysis of selected specimens from the STS-46 Energetic Oxygen Interaction with Materials-3 experiment

The Energetic Oxygen Interaction with Materials 3 (EOIM-3) experiment was flown on the STS-46 mission, which was launched on 31 Jul. 1992 and returned 8 Aug. 1992. Boeing specimens were located on both the NASA Marshall Space Flight Center (MSFC) tray and the Ballistic Missile Defense Organization (BMDO) tray integrated by the Jet Propulsion Laboratory (JPL). The EOIM-3 pallet was mounted in the Space Shuttle payload bay near the aft bulkhead. During the mission, the atomic oxygen (AO) exposure levels of specimens in these passive sample trays was about 2.3 x 10(exp 20) atoms/sq cm. The specimens also received an estimated 22 equivalent sun hours of solar exposure. In addition, it appears that the EOIM-3 pallet was exposed to a silicone contamination source and many specimens had a thin layer of silicon based deposit on their surfaces after the flight. The specimens on the MSFC tray included seven solid film lubricants, a selection of butyl rubber (B612) and silicone (S383) o-rings, three indirect scatter surfaces, and Silver/Fluorinated Ethylene Propylene (Ag/FEP) and Chemglaze A276 specimens which had previously flown on trailing edge locations of the Long Duration Exposure Facility (LDEF). The specimens on the JPL tray included composites previously flown on LDEF and two indirect scattering surfaces.

Golden, Johnny L.↗
NASA NTRS2000

Increasing Importance of Material Electrical Interaction with the Space Environment

The electrical properties of materials have always been important for spacecraft in charging environments. However, in recent years consideration of interactions of materials and systems with the plasma environment has become more and more important in spacecraft design. This has primarily been driven by independent factors including increase in power and high voltage power systems, operation of tethered satellites, and science requirements for electrostatic clean spacecraft. Increased need for power has led to increased operating voltages for spacecraft. The Upper Atmospheric Research Satellite (UARS) was one of the first to operate at near 100 V solar array potential and demonstrate that the spacecraft floated nearly the entire voltage negative of the ionospheric plasma. The high voltage, 160 V, of the solar arrays on the International Space Station (ISS) led to the requirement to have a plasma contactor to control structure potential relative to the local plasma. Issues such as sputtering, dielectric breakdown, capacitive energy storage in the structure, space debris impact induced arcs and other arcing mechanisms had to be addressed. Recently commercial satellites, driven to higher voltages for efficiency, have experienced arcing problems which led to severe, permanent power degradation. The first tethered satellite, Tethered Satellite System (TSS), was deployed from the Space Shuttle. A conductive coating was developed which provided a low resistivity and also the required solar absorptivity and emittance. Other tether systems are being designed which will have similar requirements but also long life and "bare tether" designs are also being built for flight experiments. The wire requires an electrically conductive coating with proper thermal control properties, which a bare wire doesn't possess. Increasing sophistication of scientific instruments and measurements which scientists want to make have led to increasing requirements for conducting thermal control coatings to provide electrostatic cleanliness. These issues, which are increasing the importance of electrical interaction of materials to the space environment, will be discussed in this paper as well as research into material development to meet thermal and electrical requirements and research to understand phenomena regarding such interactions.

Carruth, M. R., Jr.↗