Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ink preparation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Long-term durability test of highly efficient membrane electrode assemblies for anion exchange membrane seawater electrolyzers

Direct seawater electrolysis faces fundamental electrochemical challenges, such as suppression of chlorine adsorption and/or evolution reactions that poison the current state-of-the-art anode catalysts and accelerate the degradation of the anion exchange membrane (AEM). The technically favored solution path for addressing these issues includes development of novel selective catalysts and implementation of limited operating conditions. Therefore, development of highly active, selective, cost-effective, and stable seawater-splitting catalysts is required for a successful commercialization of the AEM water electrolyzers (AEMWEs). In this work, we report for the first-time an extended operation for over 1000 h of advanced AEMWEs, operating directly with seawater. To fabricate the membrane electrode assemblies (MEAs), catalyst coated electrodes (CCEs) are assembled with Sustainion® X37-50 grade T anion exchange membranes. The anode CCEs are fabricated by spraying an ink prepared from nanostructured NiFe-layered double hydroxide (LDH) catalyst that are synthesized by the solvothermal method and deposited directly onto platinized titanium porous transport layers (PTLs). The cathode CCEs are prepared by spraying an ink prepared from commercial Renay-Nickel catalyst onto a nickel fiber felt. As prepared AEM electrolyzer cells operated with seawater and demonstrated better than previously reported in the literature performance of over 1000 h of operation at a constant current density of 300 mA cm –2 .

25 ENERGY STORAGE↗
DOE OSTI2020

Microscopy Studies of the Catalyst Inks for PEM Fuel Cells

The microstructure of the catalyst layer in proton exchange membrane fuel cells (PEMFC) is one of the key factors that determine fuel cell performance. The ink preparation, including dispersion solvent, mixing time, and mixing power, are among the less reported parameters that would influence the ionomer distribution on the catalyst surface and the continuity of the carbon network. In this work, novel characterization approaches have been used to investigate the effect of the Pt/C catalyst ink preparation conditions on the morphology and structures of the catalyst layer. Microscopy analysis revealed that longer mixing time led to better performing electrode structures than shorter mixing time. The longer mixing time enabled improved continuity of the ionomer network and high porosity in the cathode layer that contributes to improved proton conductivity and mass transport. This has been reflected in performance and durability tests, where the electrode made from a 5-day catalyst ink displayed improved performance compared to the one made from a 3-day ink. Durability studies showed 26% and 43% loss of the initial mass activity for 5 days and 3 days mixing, respectively. Finally, in addition, the catalyst layer prepared with ethylene glycol as the dispersion solvent showed better durability than water/1-propanol based solution.

25 ENERGY STORAGE↗
DOE OSTI2021

Impact of Catalyst Ink Dispersing Solvent on PEM Fuel Cell Performance and Durability

The dispersing solvent used for fuel cell catalyst ink preparation plays a vital role in establishing the resulting morphology of the electrode layers, which in turn will impact the performance of proton exchange membrane (PEM) fuel cells. In this study, we report the impact of various ionomer dispersion solvents on PEM fuel cell performance and durability; two aqueous (1-propanol/water and 2-propanol/water) and several non-aqueous dispersing solvents (ethylene glycol and 1,2-butanediol) are compared. The cathode catalyst layer (CCL) fabricated using inks prepared with 1-propanol/water (3:1, w/w) exhibited the best initial performance followed by the CCL prepared using ethylene glycol. The CCLs made from non-aqueous ethylene glycol and 1,2-butanediol exhibited the best durability upon accelerated stress testing. Scanning transmission electron microscopy combined with energy dispersive X-ray spectroscopy indicated that, after the stress test, the distribution of both the Nafion ionomer and Pt nanoparticles within the CCLs prepared with non-aqueous ionomer dispersions underwent less change than those prepared with aqueous dispersions, which is responsible for the improved durability

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Cost-Effective Additive Manufacturing of Ambient Pressure-Dried Silica Aerogel

The conventional manufacturing processes for aerogel insulation materials mostly rely on the supercritical drying, which suffers from issues of massive energy consumption, high-cost equipment, and prolonged processing time. Considering the large market demand for the aerogel insulation material in the next decade, a cost-effective and scalable fabrication technique is highly desired. In this paper, a direct ink writing (DIW) method is used to three-dimensionally fabricate the silica aerogel insulation material, followed by room-temperature and ambient pressure drying. Compared with the supercritical drying and freeze-drying techniques, the reported method significantly reduces the fabrication time and costs. The cost-effective DIW technique offers the capability to print complex hollow internal structures, coupled with the porous aerogel structure, it is found to be beneficial for the thermal insulation property. In this work, the addition of fiber to the ink assures the durability of the fabricated product, without sacrificing the thermal insulation performance. The foam ink preparation methods and the printability are demonstrated in this paper, along with the printing of complex three-dimensional geometries. The thermal insulation performance of the printed objects is characterized, and the mechanical properties were also examined. The proposed approach is found to have a 56% reduction in the processing time. The printed silica aerogels exhibit a low thermal conductivity of 0.053 W m –1 K –1 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Opening twisted polymer chains for simultaneously high printability and battery fast-charge

Fast-charging is key to the widespread adoption of battery-based electric vehicles. However, improving fast-charging through architecture optimization is expensive. To reduce costs and expand to commercialization, we applied roll-to-roll screen printing technology to create channels and decrease the tortuosity of electrodes. For the first time, this work successfully opened twisted polymer chains within high-solid-content inks to improve their screen printability and battery performance of as-printed electrodes. With LiNi 0.6 Mn 0.2 Co 0.2 O 2 as active materials, the 60% solid content ink presents superior screen printability after opening the twisted binder chains. As-printed electrode exhibits 33% higher charge capacity at 6 C than printed electrode with chains twisted ink at mass loading of 6.5 mg/cm 2 . Furthermore, coarse-grained molecular dynamics simulations are performed to study the underlying mechanism systematically. In conclusion, the new ink preparation procedure provides a scalable, effective strategy for manufacturing screen-printable battery ink and promotes screen-printed electrode technology.

25 ENERGY STORAGE↗
DOE OSTI2025

Direct Functionalization of Established 3D-Printed Aza-Michael Liquid Crystal Elastomers with Donor–Acceptor Stenhouse Adducts

Extrusion 3D printing has advanced the manufacturing of complex liquid crystal elastomer (LCE) architectures. In parallel, donor–acceptor Stenhouse adducts (DASAs), a class of white-light-responsive photoswitches, have enabled both photochemical and photothermal LCE actuation. However, DASA–LCEs have yet to be extruded and 3D-printed. Two key challenges exist: DASA’s inherent sensitivity to heat and radicals can lead to degradation during ink preparation and printing, and small changes in the concentration of the added DASA component impact the properties of the extrudable ink, requiring reoptimization of well-established 3D-printing protocols. To overcome these challenges, we present a post-printing functionalization strategy that circumvents these limitations. Residual secondary amines, inherent to inks synthesized via standard aza-Michael addition, serve as active sites for covalent attachment of DASA photoresponsive groups following printing and cross-linking. Our method means that DASAs can be directly grafted onto 3D-printed aza-Michael LCEs without modifying the ink formulation or processing. The resulting DASA–LCEs exhibit wavelength tunability within the visible range and a variety of photothermal and photochemical responses. The post-functionalization can occur within 2 min and enables spatial control of the DASA concentration, producing films with tunable color gradients and locally varied photothermal and photochemical responses under visible light. In conclusion, this approach enables the rapid fabrication of DASA-based light-responsive LCEs using established ink formulations with the potential for the design of complex 3D architectures.

3D printing↗
DOE OSTI2023

Aging gracefully? Investigating iridium oxide ink's impact on microstructure, catalyst/ionomer interface, and PEMWE performance

Here, in this study, we conducted a thorough investigation of the impact of aging iridium oxide (IrO 2 ) perfluorosulfonic acid ionomer ink for up to 14 days on the properties of the ink and the resulting catalyst layers. We examined ink properties, such as zeta potential, dynamic light scattering (DLS), density, surface tension, and rheology, as functions of ink aging time. To evaluate the microstructure and catalyst/ionomer interface, we employed transmission electron microscopy (TEM), X-ray scattering, and X-ray photoelectron spectroscopy (XPS) techniques. Furthermore, we assessed the effect of ink aging on the performance of proton exchange membrane water electrolyzers (PEMWEs). Our findings reveal that most ink properties remain stable for 14 days. The variations in PEMWE cell performance are minimal, and no clear trend is observed in relation to ink aging time. This study demonstrates that the effects of aging the inks for 14 days on ink properties, catalyst layer structure, catalyst/ionomer interface, and PEMWE performance are negligible, indicating a substantial time window after ink preparation without any significant changes in its properties. These insights provide crucial guidance for the commercial production and coating processes of ink, which is necessary for scaling up PEM technologies to meet future demand.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

All 2D Material Printed Diodes and Circuits on Paper for Sustainable Electronics

Sustainable electronics aim to reduce environmental impact by using ecofriendly materials, energy-efficient manufacturing, and recyclable components. However, existing approaches rely on complex, resource-intensive methods, rare metals, or nanomaterials with limited stability as well as plastic substrates, raising sustainability issues. Solution-processed two-dimensional (2D) materials offer a promising alternative: water-based and biocompatible conductive, semiconductive, and insulating 2D material inks can be produced with scalable techniques and are suitable for the fabrication of fully printed devices on low-cost and biodegradable paper substrates. However, 2D material only and fully printed diodes on paper have not yet been reported. Here, we demonstrate fully inkjet-printed 2D material-based diodes on paper using metal-insulator-semiconductor and metal-insulator-metal-semiconductor architectures. Water-based graphene and MoS2 inks, prepared by liquid-phase exfoliation, are used for the metallic and insulating films, while electrochemical exfoliation is used to produce the semiconducting MoS2 ink. The highest forward-to-reverse current ratio obtained is 330 (at ±2 V), while the forward current density is 1 mA/cm2 (at 1 V), making the diode performance comparable to the best solution-processed diodes reported so far. However, in contrast to previous works, fabrication occurs entirely at room temperature and ambient pressure, without using high-pressure sputtering, thermal evaporation, and any precious metal ink. The devices maintain stable performance under bending up to strain of 4% over 10,000 cycles. Finally, the diodes are successfully integrated with other 2D-material based electrical components to realize fully printed RC circuits, differentiators, integrators, and AC-to-DC converters onto paper, hence demonstrating the suitability of our approach for sustainable and disposable integrated circuits.

2D materials↗
DOE OSTI2025

Overcoming efficiency and cost barriers for large-area quantum dot photovoltaics through stable ink engineering

The bottom-up construction of electronics from colloidal quantum dots (CQDs) could innovate nanotechnology manufacturing through printing. However, the unstable and expensive semiconductive CQD inks make the scaling up of CQD electronics challenging. Here, in this study, we develop a strategy for engineering the solution chemistry of lead sulfide (PbS) CQD inks prepared from a low-cost direct synthesis method. By creating an iodine-rich environment in weakly coordinating solvents, we convert the iodoplumbates into functional anions, which condense into a robust surface shell. The fully charged electrostatic surface layer prevents aggregation and epitaxial fusion of CQDs, yielding stable inks. By eliminating the fusion-induced inter-band states, we print a compact CQD film with uniformity in three dimensions, flattened energy landscape and improved carrier transport. We achieved a certified efficiency of 13.40% on 0.04 cm 2 cells, with a 300-fold increase in active area, scaling up to a 12.60 cm 2 module with a certified efficiency of 10%.

14 SOLAR ENERGY↗
DOE OSTI2020

EXPERIMENTAL STUDY ON COST-EFFECTIVE ADDITIVE MANUFACTURING OF SILICA AEROGEL

The conventional aerogel insulation material manufacturing from supercritical drying suffers from issues of massive energy consumption and prolonged processing time. With the consideration of large market demand of the aerogel insulation material in the next decade, a low-cost and scalable fabrication technique is highly desired. In this paper, a direct ink writing (DIW) method is used to three-dimensionally fabricate the silica aerogel insulation material, followed by ambient pressure drying. Compared to the supercritical drying and freeze drying, the reported method significantly reduces the fabrication time and costs. The cost-effective DIW technique offers the capability to print complex hollow internal structure, coupled with the porous structure, is found to be beneficial to the thermal insulation property. The addition of fiber to the ink assures the durability of the fabricated product. The foam ink preparation methods and the printability are demonstrated in this paper, along with the printed samples for characterizing thermal insulation properties and mechanical properties.

42 ENGINEERING↗
DOE OSTI2022

Charge-Density-Wave Thin-Film Devices Printed with Chemically Exfoliated 1T-TaS 2 Ink

In this work, we report on the preparation of inks containing fillers derived from quasi-two-dimensional charge-density-wave materials, their application for inkjet printing, and the evaluation of their electronic properties in printed thin-film form. The inks were prepared by liquid-phase exfoliation of CVT-grown 1T-TaS 2 crystals to produce fillers with nm-scale thickness and μm-scale lateral dimensions. Exfoliated 1T-TaS 2 was dispersed in a mixture of isopropyl alcohol and ethylene glycol to allow fine-tuning of filler particles thermophysical properties for inkjet printing. The temperature-dependent electrical and current fluctuation measurements of printed thin films demonstrated that the charge-density-wave properties of 1T-TaS 2 are preserved after processing. The functionality of the printed thin-film devices can be defined by the nearly commensurate to the commensurate charge-density-wave phase transition of individual exfoliated 1T-TaS 2 filler particles rather than by electron-hopping transport between them. The obtained results are important for the development of printed electronics with diverse functionality achieved by the incorporation of quasi-two-dimensional van der Waals quantum materials.

1T-TaS2↗
DOE OSTI2024

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗
DOE OSTI2021

In situ Al 2 O 3 incorporation enhances the efficiency of CuIn(S,Se) 2 solar cells prepared from molecular-ink solutions

Here, we report an efficiency enhancement of solution-processed CuIn(S,Se) 2 (CISSe) thin film solar cells via in situ incorporation of Al 2 O 3 . These films were produced using inks containing CuCl, InCl 3 , AlNO 3 (Al/Al + In: 0.1) and thiourea dissolved in methanol. After spin coating of these solutions in air, samples were subjected to a selenization process. Auger electron spectroscopy depth-profiling analysis showed that Al is evenly distributed throughout the bulk of the film. Transmission electron microscopy revealed that AlNO 3 precursor reacted with oxygen to form nanosized amorphous Al 2 O 3 grains located within the bulk and grain boundaries of CISSe, as well as at both the top and bottom interfaces. Power conversion efficiency (PCE) as high as 11.6% (JS C : 35.8 mA cm –2 , V OC : 518 mV, FF: 62.2%, no anti-reflection coating) was achieved with Al–CISSe solar cell devices integrated with CdS (chemical bath deposition, thickness: 80 nm) and ZnO/ITO bilayers (sputtered, thickness: 300 nm). The average PCE (10.1%, $\langle$J SC $\rangle$: 34.5 mA cm –2 , $\langle$V OC $\rangle$: 491 mV, $\langle$FF$\rangle$: 59.8%) was nearly 4% (absolute) higher than that measured on CISSe baseline cells fabricated from solutions without Al ($\langle$PCE$\rangle$ = 6.4%, $\langle$J SC $\rangle$: 32.8 mA cm –2 , $\langle$V OC $\rangle$: 410 mV, $\langle$FF$\rangle$: 47.3%). This in situ Al 2 O 3 incorporation is speculated to play a role in the enhancement of the VOC and FF of the devices through passivation of defects in CISSe reducing interface and bulk recombination, as evidenced by a reduced defect density and an increased activation energy of the dominant recombination mechanism from capacitance and temperature-dependent VOC measurements, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Additive Manufacturing of Porous Ceramics With Foaming Agent

The macro-porous ceramics has promising durability and thermal insulation performance. As porous ceramics find more and more applications across many industries, a cost-effective and scalable additive manufacturing technique for fabricating macro-porous ceramics is highly desirable. Herein, we reported a facile additive manufacturing approach to fabricate porous ceramics and control the printed porosity. Several printable ceramic inks were prepared, and the foaming agent was added to generate gaseous bubbles in the ink, followed by the direct ink writing and the ambient-pressure and room-temperature drying to create the three-dimensional geometries. In this work, a set of experimental studies were performed to optimize the printing quality. The results revealed the optimal process parameters for printing the foamed ceramic ink with a high spatial resolution and fine surface quality. Varying the concentration of the foaming agent enables the controllability of the structural porosity. The maximum porosity can reach 85%, with a crack-free internal porous structure. The tensile tests showed that the printed macro-porous ceramics possessed enhanced durability with the addition of fiber. With a high-fidelity three-dimensional (3D) printing process and the precise controllability of the porosity, we showed that the printed samples exhibited a remarkably low thermal conductivity and durable mechanical strength.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Low density syntactic foams via material extrusion additive manufacturing

An ink formulation for additive manufacturing of low density syntactic foams is described. The ink formulation can include a thermoset resin, a curing agent suitable for use with the thermoset resin, a plurality of hollow spheres, such as glass microballoons, one or more solvents, and one or more non-hollow, viscosity modifying filler. Also described are a method of preparing the ink formulation, a method of preparing three-dimensional objects comprising low density syntactic foams, and the three-dimensional objects prepared thereby.

Compton, Brett Gibson↗