SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The study introduces novel asymmetric hydrofluoroether (HFE) designs, uncovers solvation-property relationships, and leverages molecular dynamics modeling for high-performance electrolytes in advanced lithium batteries.
This NASA Engineering and Safety Center (NESC) Technical Assessment Report addresses the urgent need to identify, test, and qualify replacement cleaning solvents and technologies following 3M’s decision to discontinue production of hydrofluoroether (HFE) products, including Novec HFE-7100, by the end of 2025. HFE-7100 is widely used across NASA for precision cleaning of ground and flight hardware, especially in oxygen system components, and as a heat transfer fluid in high-power-density thermal control systems. The assessment evaluates commercially available replacement solvents, alternative cleaning technologies, and their compatibility with NASA’s operational requirements. Key findings include the identification of viable solvent replacements, their performance in contaminant removal, materials compatibility, and oxygen system safety. The report also explores novel cleaning approaches, including aqueous, supercritical CO₂, cryogenic aerosol, plasma, UV-ozone, magnetically optimized fluids, and induced charge active filtration, highlighting their merits, limitations, and readiness for NASA adoption. The NESC provides recommendations for solvent selection, facility adaptation, and continued technology maturation to ensure mission continuity and regulatory compliance.
The thermal, physical, structural, and transport properties of ionic liquid (IL) electrolytes based on n-methyl-n-butylpyrrolidinium bis(trifluoromethanesulfonyl)imide [PYR14][TFSI] and Li-salts of lithium (nonafluorobutane)(trifluoromethanesulfonyl)imide [Li][IM14] and [Li][TFSI] (0 ≤ x Li ≤ 0.3), with addition of 1,1,2,2-tetrafluoroethyl 2,2,3,3-tetrafluoropropyl ether (TTE) (0 ≤ x TTE ≤ 0.45) were studied. While [IM14] increases glass transition, TTE improves conductivity over a wider liquidus range. Li + is solvated primarily by [TFSI] with some contribution by [IM14]. However, both 7 Li- 19 F HOESY NMR and spatial distribution functions (SDFs) derived from molecular dynamics (MD) indicate short contacts between the fluorines of TTE and Li + . This is a result of tighter anion-solvated Li + without aggregation of the Li + solvates, consistent with Raman measurements, thus confirming the existence of fluorous domains in the bulk which leads to improved fluidity and a Li + diffusivity of 1.26 x 10 –12 m 2 /s at 0 °C (x Li = 0.20) with a Li + transference of 0.16. Improved transport properties translated to a higher capacity of the TTE/IL electrolyte in a Li||LiFePO 4 half-cell with 95mAh/g at 0.1C, compared to the IL electrolyte without TTE (60 mAh/g). Furthermore, this study demonstrates the tunability of solvation and transport properties in IL electrolytes by asymmetric fluorinated anions and hydrofluoroether co-solvents for low temperature Li-ion batteries.
Practical Mg batteries require electrolytes that are stable both toward reduction by Mg metal and oxidation by high voltage cathodes. State-of-the-art Mg electrolytes based on weakly-coordinating Mg salts utilize standard ether-type solvents (usually glymes) due to their reductive stability. However, the oxidative stabilities of these solvents are less than ideal, leading to difficulties in realizing the high oxidative stabilities of novel salts. On the other hand, alternative solvents with greater oxidative stability are typically unable to support Mg cycling. Here, in this work, we report a selective solvation approach involving the combination of glyme and hydrofluoroether solvents. Selective solvation of Mg 2+ by the glyme solvent component increases the oxidative stability of the glyme while maintaining sufficient reductive stability of the noncoordinating hydrofluoroether. We show that this approach enables the design of electrolytes with greater oxidative stability than glyme-only electrolytes while retaining enough reductive stability to cycle Mg metal. We also relate the influence of various coordination interactions among the solvents and anions with Mg 2+ to their electrochemical stabilities to better inform the design of future electrolytes.
A molecule's absorption in the atmospheric infrared (IR) window (IRW) is an indicator of its efficiency as a greenhouse gas. A model for estimating the absorption of a fluorinated molecule within the IRW was developed to assess its radiative impact. This model will be useful in comparing different hydrofluorocarbons and hydrofluoroethers contribution to global warming. The absorption of radiation by greenhouse gases, in particular hydrofluoroethers and hydrofluorocarbons, was investigated using ab initio quantum mechanical methods. Least squares regression techniques were used to create a model based on this data. The placement and number of fluorines in the molecule were found to affect the absorption in the IR window and were incorporated into the model. Several group increment models are discussed. An additive model based on one-carbon groups is found to work satisfactorily in predicting the ab initio calculated vibrational intensities.
Chlorofluorocarbon (CFC) 113 is currently specified as the precision cleaning and verification fluid for orbiter materials. The production ban of CFC 113, an ozone-depleting chlorofluorocarbon, has resulted in a search for a replacement cleaning fluid. Recently, the 3M Company announced the manufacture of a new class of cleaning fluids, hydrofluoroethers. The first in this class of cleaning fluids is HFE 7100, perfluorobutyl methyl ether. This cleaning fluid has been submitted for consideration as a replacement for CFC 113. One of the requirements of the certification process for a replacement cleaning fluid is compatibility testing. The Johnson Space Center (JSC) Materials and Manufacturing Division has requested that NASA JSC White Sands Test Facility perform the compatibility testing with HFE 7100 on selected orbiter materials. Most of the materials selected for testing were previously evaluated for compatibility with CFC 113. Some of the materials are new additions to the orbiter or were not available when the compatibility testing was performed with CFC 113. These materials were evaluated with both cleaning fluids and the results were used to compare the response to the cleaning fluid and to satisfy the certification process requirements. It was found that HFE 7100 is generally compatible with the materials tested.
Abstract Localized high‐concentration electrolytes (LHCEs) have attracted interest in alkali metal batteries due to the advantages of forming stable solid‐electrolyte interphases (SEIs) on anodes and good chemical/electrochemical stability. Herein, a new degradation mechanism is revealed for ether‐based LHCEs that questions their compatibility with alkali metal anodes (Li, Na, and K). Specifically, the ether solvent reacts with alkali metals to generate solvated electrons (e s − ) that attack hydrofluoroether co‐solvents to form a series of byproducts. The ether solvent essentially acts as a phase‐transfer reagent that continuously transfers electrons from solid‐phase metals into the solution phase, thus inhibiting the formation of stable SEI and leading to continuous alkali metal corrosion. Switching to an ester‐based solvating solvent or intercalation anodes such as graphite or molybdenum disulfide has been shown to avoid such a degradation mechanism due to the absence of e s − .
Abstract Localized high‐concentration electrolytes (LHCEs) have attracted interest in alkali metal batteries due to the advantages of forming stable solid‐electrolyte interphases (SEIs) on anodes and good chemical/electrochemical stability. Herein, a new degradation mechanism is revealed for ether‐based LHCEs that questions their compatibility with alkali metal anodes (Li, Na, and K). Specifically, the ether solvent reacts with alkali metals to generate solvated electrons (e s − ) that attack hydrofluoroether co‐solvents to form a series of byproducts. The ether solvent essentially acts as a phase‐transfer reagent that continuously transfers electrons from solid‐phase metals into the solution phase, thus inhibiting the formation of stable SEI and leading to continuous alkali metal corrosion. Switching to an ester‐based solvating solvent or intercalation anodes such as graphite or molybdenum disulfide has been shown to avoid such a degradation mechanism due to the absence of e s − .
Despite being an excellent candidate for lithium metal batteries due to its stability towards lithium metal, ethereal solvent suffers from relatively low anodic stability, rendering it incompatible with high voltage cathode. Although the anodic stability of ethereal solvent can be enhanced by fluorination, the lithium solvating ability of fluorinated ethers is largely reduced. As a result, common hydrofluoroethers, such as 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) and bis(2,2,2-trifluoroethyl) ether (BTFE) are not able to dissolve any lithium salt, albeit enhanced oxidation potential. Therefore, new fluorinated glycol ethers were synthesized in this research. The diglyme analog, which was terminally fluorinated, demonstrated high anodic stability and excellent capability to facilitate lithium plating/stripping. Unlike its non-fluorinated counterpart, the fluorinated diglyme analog displayed outstanding compatibility with lithium hexafluorophosphate, which is an essential salt in lithium-ion batteries. Here it was shown that the electrolyte based on fluorinated diglyme analog with fluoroethylene carbonate as co-solvent enabled highly stable cycling of Li-metal batteries pairing with layered oxide cathode.
Increasing battery energy density is greatly desired for applications such as portable electronics and transportation. However, many next-generation batteries are limited by electrolyte selection because high ionic conductivity and poor electrochemical stability are typically observed in most electrolytes. For example, ether-based electrolytes have high ionic conductivity but are oxidatively unstable above 4 V, which prevents the use of high-voltage cathodes that promise higher energy densities. In contrast, hydrofluoroethers (HFEs) have high oxidative stability but do not dissolve lithium salt. Here, we synthesize a new class of fluorinated ether electrolytes that combine the oxidative stability of HFEs with the ionic conductivity of ethers in a single compound. We show that conductivities of up to 2.7 × 10 –4 S/cm (at 30 °C) can be obtained with oxidative stability up to 5.6 V. The compounds also show higher lithium transference numbers compared to typical ethers. Furthermore, we use nuclear magnetic resonance (NMR) and molecular dynamics (MD) to study their ionic transport behavior and ion solvation environment, respectively. Finally, we demonstrate that this new class of electrolytes can be used with a Ni-rich layered cathode (NMC 811) to obtain over 100 cycles at a C/5 rate. The design of new molecules with high ionic conductivity and high electrochemical stability is a novel approach for the rational design of next-generation batteries.
Silicon (Si) anodes are promising candidates for Li-ion batteries due to their high specific capacity and low operating potential. Implementation has been challenged by the significant Si volume changes during (de)lithiation and associated growth/regrowth of the solid electrolyte interphase (SEI). In this report, fluorinated local high concentration electrolytes (FLHCEs) were designed such that each component of the electrolyte (solvent, salt, diluent) is fluorinated to modify the chemistry and stabilize the SEI of high (30%) silicon content anodes. FLHCEs were formulated to probe the electrolyte salt concentration and ratio of the fluorinated carbonate solvents to a hydrofluoroether diluent. Higher salt concentrations led to higher viscosities, conductivities, and contact angles on polyethylene separators. Electrochemical cycling of Si-graphite/NMC622 pouch cells using the FLHCEs delivered up to 67% capacity retention after 100 cycles at a C/3 rate. Post-cycling X-ray photoelectron spectroscopy (XPS) analyses of the Si-graphite anodes indicated the FLHCEs formed a LiF rich solid electrolyte interphase (SEI). The findings show that the fluorinated local high concentration electrolytes contribute to stabilizing the Si-graphite electrode over extended cycling.
Overview: LANL is using several 3M Novec TM hydrofluoroether (HFE) fluids in production processes; Novec TM HFR fluids currently being used for LANL production processes are: HFE-71IPA, HFE-72DE, HFE-7100, and HFE-7500; With the exit of these fluids being sold commercially scheduled for 2025, LANL is researching what about these HFE fluids make them specifically effective for the processes they are used for in hopes of finding adequate replacement.
The following presentation addresses LANL’s use of Novec™ fluids and specific fluid properties; LANL uses several 3M Novec™ hydrofluoroether (HFE) fluids in various production processes; Novec™ HFE fluids currently used are: HFE-71IPA; HFE-72DE; HFE-7100; HFE-7500; Plutonium’s unique properties and challenging manufacturing conditions require fluids to be above all else: non-flammable; chemically inert.
The Li-S battery is a promising next-generation technology due to its high theoretical energy density (2600 Wh kg -1 ) and low active material cost. However, poor cycling stability and coulombic efficiency caused by polysulfide dissolution have proven to be major obstacles for a practical Li-S battery implementation. In this work, we develop a novel strategy to suppress polysulfide dissolution using hydrofluoroethers (HFEs) with bi-functional, amphiphlic surfactant-like design: a polar lithiophilic "head" attached to a fluorinated lithiophobic "tail." A unique solvation mechanism is proposed for these solvents whereby dissociated lithium ions are readily coordinated with lithiophilic "head" to induce self-assembly into micelle-like complex structures. Complex formation is verified experimentally by changing the additive structure and concentration using small angle X-ray scattering (SAXS). These HFE-based electrolytes are found to prevent polysulfide dissolution and to have excellent chemical compatibility with lithium metal: Li||Cu stripping/plating tests reveal high coulombic efficiency (>99.5%), modest polarization, and smooth surface morphology of the uniformly deposited lithium. Li-S cells are demonstrated with 1395 mAh g-1 initial capacity and 71.9% retention over 100 cycles at >99.5% efficiency-evidence that the micelle structure of the amphiphilic additives in HFEs can prohibit polysulfide dissolution while enabling facile Li + transport and anode passivation.
Hydrochlorofluorocarbon (HCFC) 141b has been selected as the interim blowing agent for use in urethane insulations on NASA's Space Shuttle External Tank. Due to the expected limited commercial lifetime of this material, research efforts at the NASA Thermal Protection Systems Materials Research Laboratory at the Marshall Space Flight Center are now being devoted to the identification and development of alternatives with zero ozone depletion potential. Physical blowing agents identified to date have included hydrocarbons, fluorocarbons, hydrofluoroethers, and more predominantly, hydrofluorocarbons (HFCs). The majority of the HFC evaluations in industry have focused on the more readily available, low boiling candidates such as HFC 134a. Higher boiling HFC candidates that could be handled at ambient conditions and use current processing equipment would be more desirable. This paper will describe results from a research program of two such candidate HFC's performed as a cooperative effort between Martin Marietta Manned Space Systems, the U.S. Environmental Protection Agency, and Oak Ridge National Laboratories. The purpose of this effort was to perform a cursory evaluation of the developmental HFC's 245ca and 236ea as blowing agents in urethane based insulations. These two materials were selected from screening tests of 37 C2, C3, and C4 isomers based on physical properties, atmospheric lifetime, flammability, estimated toxicity, difficulty of synthesis, suitability for dual use as a refrigerant, and other factors. Solubility of the two materials in typical foam components was tested, pour foaming trials were performed, and preliminary data were gathered regarding foam insulation performance.
The Gateway will be humanity’s first space station orbiting the Moon completed by NASA in partnership with ESA and other US and international partners. The Gateway will provide critical support to sustainable human exploration on the moon through the Artemis program. To enable the Lunar Gateway to complete its mission, on orbit refuelling is essential. The ESPRIT Refuelling Module (ERM) will provide the capability to transfer propellants, MMH and MON-3, through the Habitation and Logistics Outpost (HALO) to the Power and Propulsion Element (PPE). The transfer of these propellants carries known risks and hazards. These hazards include overpressure of the propellant lines during priming sequences between modules and during refuelling pause operations. To support the early system development and to mitigate these risks, a collaborative test program between NASA, ESA and Thales Alenia Space was completed at the Thales Alenia Space test facility in Harwell, UK. This test program integrated fluidic breadboards of the ERM, HALO and PPE modules. The objectives of the test program were to demonstrate and characterise critical performance and transient operations, inform refuelling concept of operations and to calibrate and validate numerical models of the refuelling subsystem in EcosimPro. To support the completion of this final objective a detailed model of the integrated breadboard was developed in EcosimPro and key steady-state and transient test cases were simulated. As an industry first, a National Institute of Standards and Technology (NIST) database correlation for Hydrofluoroether (HFE-7000) was used as a mixed oxides of nitrogen (MON-3) simulant with EcosimPro and European Space Propulsion System Simulation (ESPSS) libraries to result in a more accurate analysis for transient phenomenon such as priming. The test and simulation data showed good agreement validating the model for further system analysis as the ERM design progresses.
A highly adsorptive structure, includes: a substrate; and a metal-organic framework (MOF) comprising a plurality of metal atoms coordinated to a plurality of organic spacer molecules; wherein the MOF is coupled to at least one surface of the substrate, wherein the MOF is adapted for adsorbing and desorbing a refrigerant under predetermined thermodynamic conditions. The refrigerant includes one or more materials selected from the group consisting of: acid halides, alcohols, aldehydes, amines, chlorofluorocarbons, esters, ethers, fluorocarbons, perfluorocarbons, halocarbons, halogenated aldehydes, halogenated amines, halogenated hydrocarbons, halomethanes, hydrocarbons, hydrochlorofluorocarbons, hydrofluoroethers, hydrofluoroolefins, inorganic gases, ketones, nitrocarbon compounds, noble gases, organochlorine compounds, organofluorine compounds, organophosphorous compounds, organosilicon compounds, oxide gases, refrigerant blends and thiols.
A highly adsorptive structure includes: a substrate; and a carbon aerogel adhered to the substrate, wherein the carbon aerogel is characterized by having physical characteristics of in-situ formation on the substrate, and wherein the carbon aerogel is configured to selectively adsorb and desorb one or more refrigerants selected from the group consisting of: acid halides, alcohols, aldehydes, amines, chlorofluorocarbons, esters, ethers, fluorocarbons, perfluorocarbons, halocarbons, halogenated aldehydes, halogenated amines, halogenated hydrocarbons, halomethanes, hydrocarbons, hydrochlorofluorocarbons, hydrofluoroethers, hydrofluoroolefins, inorganic gases, ketones, nitrocarbon compounds, noble gases, organochlorine compounds, organofluorine compounds, organophosphorous compounds, organosilicon compounds, oxide gases, refrigerant blends and thiols.