Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “homogeneous charge compression ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Methanol mixing−controlled compression ignition enabled via homogeneous charge compression ignition of dimethyl ether through catalytic decomposition of methanol

Methanol is a potentially attractive fuel for marine and off−road engines owing to its availability at bunkering and global distribution locations. Although methanol is well−distributed worldwide, its fuel chemistry and ignition properties make it poorly suited as a direct drop−in replacement for diesel fuel in compression−ignition engines. However, industrial processes are regularly used to convert methanol, via catalytic dehydration, to dimethyl ether (DME) over nonprecious metal catalysts. This chemical conversion can occur at relatively low pressures, temperatures, and catalyst space velocities, highlighting a potential opportunity to generate DME via onboard catalytic dehydration of methanol. DME’s fuel kinetic and ignition properties for compression ignition are much more favorable than those of methanol or even diesel fuel, but DME is more challenging than diesel fuel or methanol to pump, store, and deliver through conventional diesel fueling injection hardware. Thus, a potential opportunity exists to use the ignition and kinetic properties of DME, with the transportation and delivery advantages of methanol, in a methanol−fueled mixing−controlled compression−ignition engine. The present work explores performance, combustion behavior, and emissions reduction opportunities for methanol mixing−controlled combustion, enabled by a HCCI of DME that represents a small fraction of the total fuel energy that can be generated onboard via catalytic dehydration of methanol.

Splitter, Derek [ORNL] (ORCID:0000000174044047)↗
DOE OSTI2020

Enhancing the efficiency benefit of thermal barrier coatings for homogeneous charge compression ignition engines through application of a low-k oxide

Prior experiments reported by the authors have proven the hypothesis that achieving a dynamic temperature swing on the combustion chamber surface will lead to improved thermal and combustion efficiencies of the homogeneous charge compression ignition engine. A thin layer of yttria-stabilized zirconia, roughly 150 μm, was plasma sprayed on the piston top. It led to markedly advanced ignition and heat release in the gasoline homogeneous charge compression ignition engine, accompanied with reduced unburnt hydrocarbon and carbon monoxide emissions, improved combustion efficiency, and a higher thermal efficiency. A related computational study highlighted the critical role of coating thermal conductivity in achieving a desired dynamic response; hence, the second phase of experimental investigations focused on introducing structured porosity in the yttria-stabilized zirconia coating, as a means of reducing effective conductivity. Indeed, additional incremental improvements were observed, as well as limitations related to adverse effects of the surface roughness and the fuel interactions with the surface roughness and open pores. Erosion can also be a problem in a direct injection engine. Therefore, the third round of investigations focused on a material with a natively low conductivity (low-k), sprayed on the top of an Al piston in a relatively dense form, and in a way that yields a smooth surface. The objective was to capitalize on the low conductivity, while avoiding the pitfalls accompanying high-porosity formulations. The heat-storage capacity was limited by keeping the thickness relatively low. The results verify the paramount importance of thermal conductivity in the context of high “temperature swing” behavior and indicate a potential to improve the homogeneous charge compression ignition engine’s combustion efficiency roughly 1.5%, with the overall indicated efficiency improvement on the order of 5%, on a relative basis. In addition, the low-k oxide thermal barrier applied to the piston extended significantly the low-load homogeneous charge compression ignition operability limit.

42 ENGINEERING↗
DOE OSTI2020

Computationally efficient evaluation of optimum homogeneous charge compression ignition operating range with accelerated multizone engine cycle simulation

The very intensive calculations necessary to define a performance map requiring evaluation of over a hundred individual operating points can be efficiently conducted with accelerated multizone for engine cycle simulation, leading to a definition of regions of acceptable and optimum homogeneous charge compression ignition operation. Accelerated multizone for engine cycle simulation has the virtue of enabling accurate evaluation of many operating conditions based on thermal stratification data from a single fluid mechanics run at motored conditions. This is possible because thermal stratification is more sensitive to engine geometry than to operating conditions. In this article, accuracy of accelerated multizone for engine cycle simulation is demonstrated by comparison with experimental data for iso-octane homogeneous charge compression ignition operation over a broad range of lean equivalence ratios (0.14–0.28). The validated accelerated multizone for engine cycle simulation model is then applied to generating a performance map for an engine controlled by appropriately adjusting equivalence ratio and internal exhaust gas recirculation. Regions of acceptable and optimum combustion are identified. It is finally demonstrated that while indicated mean effective pressure remains low for optimum homogeneous charge compression ignition operation (1–4 bar), this is sufficient for a large fraction of typical driving in light-duty vehicles. Much driving including idle can therefore be done in homogeneous charge compression ignition mode at high efficiency and low (essentially zero) NOx and particulate matter emissions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

An experimental and kinetic modeling study of NO x sensitization on methane autoignition and oxidation

An experimental and kinetic modeling study of the influence of NO x (i.e. NO 2 , NO and N 2 O) addition on the ignition behavior of methane/‘air’ mixtures is performed. Ignition delay time measurements are taken in a rapid compression machine (RCM) and in a shock tube (ST) at temperatures and pressures ranging from 900–1500 K and 1.5–3.0 MPa, respectively for equivalence ratios of 0.5–2.0 in ‘air’. The conditions chosen are relevant to spark ignition and homogeneous charge compression ignition engine operating conditions where exhaust gas recirculation can potentially add NO x to the premixed charge. The RCM measurements show that the addition of 200 ppm NO 2 to the stoichiometric CH 4 /oxidizer mixture results in a factor of three increase in reactivity compared to the baseline case without NOx for temperatures in the range 600–1000 K. However, adding up to 1000 ppm N 2 O does not show any appreciable effect on the measurements. The promoting effect of NO 2 was found to increase with temperature in the range 950–1150 K, while the sensitization effect decreases at higher pressures. The experimental results measured are simulated using NUIGMech1.2 comprising an updated NO x sub-chemistry in this work. A kinetic analysis indicates that the competition between the reactions ĊH 3 + NO 2 ↔ CH 3 Ȯ + NO and ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), the former being a propagation reaction and the latter being a termination reaction governs NO x sensitization on CH 4 ignition. Recent calculations by Matsugi and Shiina (A. Matsugi, H. Shiina, J. Phys. Chem. A. 121 (2017) 4218–4224) for the nitromethane formation reaction CH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), together with the recently calculated rate constants for HONO/HNO 2 reactions significantly improve ignition delay time predictions in the temperature range 600–1000 K. Furthermore, the experiments with NO addition reveal a non-monotonous sensitization impact on CH 4 ignition at lower temperatures with NO initially acting as an inhibitor at low NO concentrations and then as a promoter as NO concentrations increase in the mixture. This non-monotonous trend is attributed to the role of the chain-termination reaction ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M) and the impact of NO on the transition to the chain-branching steps CH 2 O + HȮ 2 ↔ HĊO + H 2 O 2 , H 2 O 2 (+M) ↔ ȮH + ȮH (+M), HĊO ↔ CO + Ḣ followed by CO + O 2 ↔ CO 2 + Ö and Ḣ + O 2 ↔ Ö + ȮH. NUIGMech1.2 is systematically validated against the new ignition delay measurements taken here together with species measurements and high temperature ignition delay time data available in the literature for CH 4 /oxidizer mixtures diluted with NO 2 /N 2 O/NO and is observed to accurately capture the sensitization trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Alkyl dialkoxyalkanoates as bioderived, high cetane diesel fuels

A fuel for an internal combustion engine includes a C 5 to C 30 dialkoxyalkanoate corresponding to formula (I), wherein the R 1 group is —H or a —CH 3 group, the R 2 and R 2 ′ groups are alkyl groups independently selected to have 1 to 9 carbon atoms; and the R 3 group is selected to have 1 to 9 carbon atoms. The compounds described herein may be used as neat fuels or mixed fuels (with diesel, biodiesel, jet fuel, marine fuel or other fuel compounds) in autoignition or spark ignition engines, such as diesel engines, gasoline (spark ignition) engines, MCCI, Homogeneous Charge Compression Ignition (HCCI) engines, or more generally in Low-Temperature Gasoline Combustion (LTGC) engines (using gasoline-like fuels), that have the high-efficiency advantages of HCCI but can operate with some level of charge inhomogeneities. Methods of making these compounds are environmentally friendly and can be done in a continuous manner.

Myllenbeck, Nicholas↗
DOE OSTI2026

Methanol mixing controlled combustion process enabled by methanol dehydration to dimethyl ether

This work demonstrates an initial proof-of-concept approach for operating a compression ignition off-road and marine relevant engine using neat methanol. The approach utilizes mixing controlled compression ignition (MCCI) of methanol that is enabled by a homogeneous charge compression ignition (HCCI) pre-burn of premixed dimethyl ether (DME). Although two fuels are used, this work explores and evaluates the opportunity and performance to generate the premixed fuel via. methanol catalytic dehydration over an alumina catalyst at engine relevant temperatures, pressures, and space velocities. Conversion purity and species output results from catalytic dehydration bench flow reactor studies were coupled with single cylinder experiments of the characterized output species for pre-burn HCCI performance. Subsequent initial methanol MCCI performance is also evaluated and compared relative to conventional diesel combustion. The detailed flow reactor results show that the catalytic dehydration conversion efficiency of methanol to DME is a function of system pressure, temperature, and space velocity. The engine results demonstrate that a 100% conversion of methanol to DME is not required for successful pre-burn HCCI, and the water formed during the dehydration process does not need to be removed to achieve the desired HCCI event from this pre-burn mixture. Subsequent methanol MCCI combustion results show that the level of methanol slip in the dehydration process affects the pre-burn HCCI phasing, low temperature heat release process, and magnitude of energy released, all of which can dictate the available window for direct injection of methanol for MCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

LES of HCCI combustion of iso-octane/air in a flat-piston rapid compression machine

Homogeneous Charge Compression Ignition (HCCI) engines promise better efficiency and cleaner emissions than conventional piston engines, but can be challenging to control. Rapid compression machines (RCM) provide a simplified configuration for investigating HCCI combustion behavior, which is necessary for effective control of engine ignition timing and peak pressures. Here, in this study, we assess the utility of large eddy simulations (LES) for predicting HCCI combustion in a 3-D configuration. To this end, LES with finite-rate chemistry employing a 99-species iso-octane/air mechanism of two RCM operating conditions are performed. The RCM configuration under consideration was designed by Strozzi et al. with a flat piston to introduce large amounts of thermal stratification representative of realistic HCCI engine conditions, through the generation of corner vortices. It is shown that the simulation provides reasonable agreement with temperature fluctuations (7% difference), as well as ignition delay in the short ignition case (1 ms difference), while the long ignition case (35 ms difference) highlights more substantial deficiencies that are still within the expected uncertainty from the employed chemical mechanism. Flame propagation modes predicted by LES agree with experimental observations: spontaneous ignition is seen in the short ignition case, while deflagration is more prominent in the long ignition case. Analysis of global and local quantities classify the short ignition case in a mixed ignition regime, and the long ignition case in the mild ignition regime. These results demonstrate the utility of FRC-LES for investigations of multimode combustion regimes of HCCI combustion in a 3-D configuration.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Gasoline fuels properties for multi-mode operation – Observations in a GDI and the CFR engine

The combustion behavior of five full boiling range RON98 gasoline blends was evaluated for multi-mode operation in a GDI and the CFR octane rating engine. The GDI engine tests were conducted with stoichiometric air-fuel ratio in spark-ignition (SI), and with air-diluted homogeneous charge compression ignition (HCCI) mode. In the CFR engine, the knocking combustion was analyzed under standard RON testing conditions at both peak knocking lambda and stoichiometric air-fuel ratios, whereas compression ignited operation was characterized by utilizing the HCCI number test protocol. Disparate knock limited SI and HCCI combustion behavior was observed for the test fuels, despite four of the fuels having the same RON and octane sensitivity. It was found that knock-limited combustion phasing in the GDI engine did not align well with the RON. However, a detailed comparison of knock-limited SI operation in the GDI and CFR engine revealed that a more appropriate effective RON based on a common knock intensity metric (MAPO) and stoichiometric air-fuel ratio resulted in comparable knock characterization between the two engine platforms. Furthermore, the critical intake air temperature and the critical compression ratio were proposed to characterize knock-limited SI operation, while the minimum intake air heating and compression ratio were used to define a fuel's autoignition propensity for compression ignition operation in the GDI and CFR engine, respectively. Finally, each fuel's characteristic compression ratio needed to obtain knock-limited SI (KLSI) and HCCI operation was used to calculate an effective multi-mode octane number (MM-ON) based on the primary reference fuel blends.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

A co-kurtosis PCA based dimensionality reduction with nonlinear reconstruction using neural networks

For turbulent reacting flow systems, identification of low-dimensional representations of the thermo-chemical state space is vitally important, primarily to significantly reduce the computational cost of device-scale simulations. Principal component analysis (PCA), and its variants, are a widely employed class of methods. Recently, an alternative technique that focuses on higher-order statistical interactions, co-kurtosis PCA (CoK-PCA), has been shown to effectively provide a low-dimensional representation by capturing the stiff chemical dynamics associated with spatiotemporally localized reaction zones. While its effectiveness has only been demonstrated based on a priori analyses with linear reconstruction, in this work, we employ nonlinear techniques to reconstruct the full thermo-chemical state and evaluate the efficacy of CoK-PCA compared to PCA. Specifically, we combine a CoK-PCA-/PCA-based dimensionality reduction (encoding) with an artificial neural network (ANN) based reconstruction (decoding) and examine, a priori, the reconstruction errors of the thermo-chemical state. In addition, we evaluate the errors in species production rates and heat release rates, which are nonlinear functions of the reconstructed state, as a measure of the overall accuracy of the dimensionality reduction technique. We employ four datasets to assess CoK-PCA/PCA coupled with ANN-based reconstruction: zero-dimensional (homogeneous) reactor for autoignition of an ethylene/air mixture that has conventional single-stage ignition kinetics, a dimethyl ether (DME)/air mixture which has two-stage (low and high temperature) ignition kinetics, a one-dimensional freely propagating premixed ethylene/air laminar flame, and a two-dimensional dataset representing turbulent autoignition of ethanol in a homogeneous charge compression ignition (HCCI) engine. Finally, results from the analyses demonstrate the robustness of the CoK-PCA based low-dimensional manifold with ANN reconstruction in accurately capturing the data, specifically from the reaction zones.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Transported Livengood–Wu Integral Model for Knock Prediction in Computational Fluid Dynamics Simulation

This work describes the development of a transported Livengood–Wu (L–W) integral model for computational fluid dynamics (CFD) simulation to predict autoignition and engine knock tendency. The currently employed L–W integral model considers both single-stage and two-stage ignition processes, thus can be generally applied to different fuels such as paraffin, olefin, aromatics, and alcohol. The model implementation is first validated in simulations of homogeneous charge compression ignition (HCCI) combustion for three different fuels, showing good accuracy in prediction of autoignition timing for fuels with either single-stage or two-stage ignition characteristics. Then, the L–W integral model is coupled with G-equation model to indicate end-gas autoignition and knock tendency in CFD simulations of a direct-injection spark-ignition engine. This modeling approach is about 10 times more efficient than the ones that based on detailed chemistry calculation and pressure oscillation analysis. Two fuels with same Research Octane Number (RON) but different octane sensitivity are studied, namely, Co-Optima alkylate and Co-Optima E30. Feed-forward neural network model in conjunction with multivariable minimization technique is used to generate fuel surrogates with targets of matched RON, octane sensitivity, and ethanol content. The CFD model is validated against experimental data in terms of pressure traces and heat release rate for both fuels under a wide range of operating conditions. The knock tendency—indicated by the fuel energy contained in the autoignited region—of the two fuels at different load conditions correlates well with the experimental results and the fuel octane sensitivity, implying the current knock modeling approach can capture the octane sensitivity effect and can be applied to further investigation on composition of octane sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

A transported Livengood-Wu integral model for knock prediction in CFD simulation

This work describes the development of a transported Livengood-Wu (L-W) integral model for computational fluid dynamics (CFD) simulation to predict auto-ignition and engine knock tendency. The currently employed L-W integral model considers both single-stage and two-stage ignition processes, thus can be generally applied to different fuels such as paraffin, olefin, aromatics and alcohol. The model implementation is first validated in simulations of homogeneous charge compression ignition combustion for three different fuels, showing good accuracy in prediction of auto-ignition timing for fuels with either single-stage or two-stage ignition characteristics. Then, the L-W integral model is coupled with G-equation model to indicate end-gas auto-ignition and knock tendency in CFD simulations of a direct injection spark ignition engine. This modeling approach is about 10 times more efficient than the ones that based on detailed chemistry calculation and pressure oscillation analysis. Two fuels with same Research Octane Number (RON) but different octane sensitivity are studied, namely Co-Optima Alkylate and Co-Optima E30. Feed-forward neural network model in conjunction with multi-variable minimization technique is used to generate fuel surrogates with targets of matched RON, octane sensitivity and ethanol content. The CFD model is validated against experimental data in terms of pressure traces and heat release rate for both fuels under a wide range of operating conditions. The knock tendency indicated by the fuel energy contained in the auto-ignited region of the two fuels at different load conditions correlates well with the experimental results and the fuel octane sensitivity, implying the current knock modeling approach can capture the octane sensitivity effect and can be applied to further investigation on composition of octane sensitivity.

Yue, Zongyu↗
DOE OSTI2020

Autoignition behavior of gasoline/ethanol blends at engine-relevant conditions

Ethanol is an attractive oxygenate increasingly used for blending with petroleum-derived gasoline yielding beneficial combustion and emissions behavior for a range of internal combustion engine schemes, including stoichiometric spark-ignition and low temperature combustion (LTC). As such, it is important to fundamentally understand the autoignition behavior of gasoline/ethanol blends. This work utilizes a rapid compression machine (RCM) and a homogeneous charge compression ignition (HCCI) engine to experimentally quantify changes in fuel reactivity, through ignition delay times and preliminary heat release, for blends of 0 to 30% vol./vol. into a full boiling range research gasoline (FACE-F). Diluted/stoichiometric and undiluted/fuel-lean conditions are explored covering a wide range of compressed temperatures and pressures relevant to conventional and advanced, gasoline combustion engines. Detailed chemical kinetic modeling is undertaken using a recently updated gasoline surrogate model in conjunction with a five-component surrogate to model the RCM experiments and provide chemical insight into the perturbative effects of ethanol on the autoignition process. The diluted/stoichiometric RCM measurements reveal that within the low-temperature regime ethanol retards first-stage and main ignition delay times, and suppresses both the rates and extents of low-temperature heat release (LTHR), while within the intermediate-temperature regime ethanol only causes slight changes. Good agreement of ignition delay time and preliminary heat release prediction is found between model and experimental results. Sensitivity and flux analyses further show that ethanol blending effects are dominated by the competition between the H-atom abstraction from ethanol and other fuel components by OH radical at low temperatures and by HO 2 radical at intermediate temperatures. These findings are consistent across both fuel loading conditions explored in this study. In addition, when HCCI engine experiments are mapped onto undiluted/lean RCM measurements under a constant combustion phasing scenario, good correspondence between the two apparatuses is observed for LTHR and start of high-temperature heat release. Finally, the current study highlights the importance of characterizing LTHR in predicting fuel behaviors in high-boost/low-temperature engines, and demonstrates that RCM experiments can provide an alternative, and more-efficient avenue for such characterization.

02 PETROLEUM↗
DOE OSTI2026

Effect of NO on DME-Methanol HCCI Combustion Using a Reduced Chemical Kinetics Mechanism

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) mixing controlled compression ignition (MCCI) of neat methanol. Within that context, complementary experimental work found that the influence of combustion residuals on the heat release rate (HRR) was significant, specifically for residual NO. This finding motivated the present computational and kinetic evaluation of the effects of NO on the low (LTHR) and high (HTHR) temperature heat release rates. The strong influence of small quantities of NO on the combustion process of a DME/methanol/H2O mixture (low catalyst or reactor efficiency) necessitated a kinetics-based investigation into this phenomenon. A mechanism sourced from the existing literature with NO had 172 species and 1375 reactions, making it computationally expensive for use. Hence, a mechanism reduction effort was implemented, and a rate constant (k) tuning effort based on sensitivity analysis was needed to validate experimental results using a zero-dimensional engine model in Cantera. The reduced mechanism was able to successfully capture the negligible influence of NO addition on DME HCCI combustion, whereas an advancement in LTHR and HTHR for a DME/methanol/H2O mixture was kinetically confirmed. Reaction pathway analysis showed that addition of NO chemically counteracted the OH sink created by alcohols like methanol, increasing the effectiveness of DME ignition.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗
DOE OSTI2026

Effect of NO on DME-Methanol HCCI Experimental Observations

Methanol is an attractive fuel for the maritime sector due to its wide availability. Its direct use as a fuel, however, is accompanied by challenges such as high latent heat of vaporization and low cetane number. A potential solution to overcome the ignition properties of methanol could be through on-board generation of dimethyl ether (DME) via catalytic dehydration of methanol. The resulting mixture from dehydration can be mixed in with the intake air to generate a homogenous charge compression ignition (HCCI) preburn for subsequent direct injection (DI) and successful ignition methanol at diesel–like timescales. However, if the preburn species are treated separately from the complete methanol MCCI approach the preburn heat release rate (HRR) phasing and behavior do not replicate the preburn behavior of the complete approach. Thus, the presence of the main methanol mixing controlled compression ignition (MCCI) combustion event influences the DME/methanol preburn kinetics. Specifically, it was found that trapped residual temperature alone was insufficient alone to be responsible for the observed differences, and that trace species concentrations of NO in the trapped residual gas also influenced DME/methanol kinetics increasing low temperature heat release (LTHR) magnitude and advancing high temperature heat release (HTHR) phasing. NO is not present in HCCI combustion of neat DME or DME/methanol blends nor is elevated gas temperature in the trapped residuals; both of which result in failure to accurately predict the HCCI combustion of DME/methanol blends when coupled with subsequent DI methanol MCCI. This work experimentally explores the effect of trapped residual temperature and NO on DME and DME/methanol HCCI combustion.

Jatana, Gurneesh [ORNL] (ORCID:0000000288903225)↗
DOE OSTI2026

A single-zone zero-dimensional study of HCCI combustion of methanol dehydration products to enable ignition of direct-injected methanol

Methanol is an alternative fuel gaining traction in the maritime sector. Its direct adoption, however, is accompanied by a unique set of technical challenges, such as low cetane number and high latent heat of vaporization. An approach to overcome these challenges is being developed at the US Department of Energy’s Oak Ridge National Laboratory, where onboard generation of dimethyl ether (DME) via catalytic dehydration of methanol can be used to assist in the mixing controlled combustion of direct-injected (DI) methanol. The generated mixture from this dehydration process can be premixed with intake air to condition the cylinder via. homogeneous charge compression ignition (HCCI) for subsequent DI methanol. In this preliminary work, various catalyst or reactor conversion efficiencies were simulated (using bottles) at constant DME and water flow at low load on a single-cylinder marine-variant of a CAT® C18 18 L engine with a 145 mm bore. To substantiate the experimental findings, a zero-dimensional engine model was developed in Cantera using a DME mechanism with 79 species and 658 reactions. Results presented include experimental and simulation heat release rate comparisons, species evolution information, and constant volume ignition delay (ID) for DI methanol with and without background species from HCCI of the premixed products from different reactor efficiencies. The results suggest that thermal effects dominate the DI methanol ignition process, and this work provides a chemical kinetic foundation or guideline for developing future control schemes.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗
DOE OSTI2022

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗