Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high-octane gasoline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Catalyst design to direct high-octane gasoline fuel properties for improved engine efficiency

The paraffin-to-olefin (P/O) ratio in gasoline fuel is a critical metric affecting fuel properties and engine efficiency. In the conversion of dimethyl ether (DME) to high-octane hydrocarbons over BEA zeolite catalysts, the P/O ratio can be controlled through catalyst design. Here, we report bimetallic catalysts that balance the net hydrogenation and dehydrogenation activity during DME homologation. The Cu-Zn/BEA catalyst exhibited greater relative dehydrogenation activity attributed to higher ionic site density, resulting in a lower P/O ratio (6.6) versus the benchmark Cu/BEA (9.4). The Cu-Ni/BEA catalyst exhibited increased hydrogenation due to reduced Ni species, resulting in a higher P/O ratio (19). The product fuel properties were estimated with an efficiency merit function and compared against finished gasolines and a typical alkylate blendstock. Merit values for the hydrocarbon product from all three BEA catalysts exceeded those of the comparison fuels (0–5.3), with the product from Cu-Zn/BEA exhibiting the highest merit value (9.7).

Catalyst design↗
DOE OSTI2022

A separations and purification process for improving yields and meeting fuel contaminant specifications for high-octane gasoline produced from dimethyl-ether over a Cu/BEA catalyst

In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.

09 BIOMASS FUELS↗
DOE OSTI2022

High-Octane Gasoline from Lignocellulosic Biomass via Syngas and Methanol/Dimethyl Ether Intermediates (2021 State of Technology)

The 2021 state of technology (SOT) assessment for the indirect liquefaction (IDL) of lignocellulosic biomass to high-octane gasoline (HOG) via methanol and dimethyl ether (DME) intermediates details the techno-economic analysis (TEA) results and technical progress of the pathway since the 2020 SOT report. A detailed process description and collection of underlying assumptions is given the 2015 design report. In 2021, research efforts rigorously quantified the selectivity of DME to aromatic compounds. As a result, the overall carbon selectivity to hydrocarbon products was updated based upon new findings. Additionally, research conducted over the past few years resulted in successful lower temperature regeneration of NREL's Cu/BEA catalyst with favorable implications on catalyst longevity. Discussions with an engineering firm resulted in an update to the excess air requirement for process combustors (including the char combustor, tar reformer combustor, and catalyst regenerator) in which excess air was reduced from 20% excess to 10%. The cumulative effect of the above efforts was used to calculate a minimum fuel selling price for the modeled pathway. Sensitivity cases examining federal carbon tax credits from CO 2 capture, product selectivity and yield, catalyst lifetime, and other key financial and process parameters were also considered in this assessment.

09 BIOMASS FUELS↗
DOE OSTI2021

High-Octane Gasoline from Lignocellulosic Biomass via Syngas and Methanol/Dimethyl Ether Intermediates: 2020 State of Technology

The 2020 state of technology (SOT) serves as an update to the 2019 SOT report and details the techno-economic analysis (TEA) results for producing high-octane gasoline (HOG) via indirect liquefaction (IDL). This report only describes changes to the experimental and analysis results from previous SOTs; more details regarding the full process design can be found in the 2015 design report. The conversion pathway presented in this report includes the gasification of biomass, steam reforming and cleanup of the syngas, followed by the conversion of the syngas to HOG via methanol and dimethyl-ether (DME) intermediates. Research efforts in 2020 included the collection of experimental results over a variety of isobutane (iC4) to DME ratios in the feed of the DME-to-HOG reactor, enabling the TEA to identify the effect on modeled product yield and cost. Additionally, a significant re-build of the Aspen Plus model allowed for better integration of new research, however underlying conceptual and economic assumptions remain the same as those detailed in the 2015 deign report. The 2020 SOT also considers the potential for federal carbon tax credits from CO 2 capture in the acid-gas removal step and the impact on the final minimum fuel selling price.

09 BIOMASS FUELS↗
DOE OSTI2022

Benchmarking Cu/BEA and HBEA catalysts for high-octane gasoline synthesis

We distinguish rates at which carbon deposition occurs during initiation, rates at which catalytic centers are lost during deactivation, and paraffin-to-olefin ratio during propagation as benchmarks that distinguish 5 wt% Cu/H-BEA and H-BEA (Si/Al = 13.5) catalysts during dimethyl ether (DME) homologation in the presence of hydrogen. Studies that systematically vary initial DME contact time (210, 94, and 45 mol H+, initial s (mol C ) -1 ), DME pressure (4 and 22 kPa), and H 2 pressure (1, 24, and 48 kPa) reveal that Cu enables lower carbon deposition rates (on a per proton basis) in the induction period, increases the effluent paraffin-to-olefin ratio during propagation, and decreases the instantaneous site-loss yields by a factor of ~ 1.5-2x (moles of active sites lost per mole of DME) during termination sequences thus affecting the degree of product saturation and catalyst stability during DME homologation. Furthermore, these results provide mechanistic insights revealing the critical role of Cu in facilitating DME homologation to high value, high-octane gasoline-range hydrocarbons with higher cumulative turnovers than proton form H-BEA.

09 BIOMASS FUELS↗
DOE OSTI2021

BETO 2021 Peer Review - Thermochemical Platform Analysis WBS: 2.1.0.302

The objective of the NREL Thermochemical Platform Analysis (WBS 2.1.0.302) project is to inform and guide R&D priorities for thermal and catalytic conversion processes by providing process design and techno-economic analysis (TEA). This is achieved through close collaboration with researchers and external experts, along with the use of both commercially available modeling tools and the development or use of collaboration-derived domain-specific tools and resources, such as refinery integration, kinetic and reactor models, phase equilibrium models, and pertinent bio-products market studies. This project is directly aligned with DOE-BETO goals, with the enabling of technology advancements and cost reduction for biomass derived biofuels being one of its primary objectives. TEA-guided research facilitated by this project has helped achieve significant modeled cost reductions for the ex situ catalytic fast pyrolysis (CFP) pathway and the indirect liquefaction (IDL) pathway for the conversion of syngas to high-octane gasoline (HOG). Cost reduction through refinery integration, development of valuable co-products, and other options are being identified for future research to help reduce the modeled MFSP to $2.50/GGE by 2030. Additional priorities anticipated in the future, such as the use of renewable electricity for liquid fuels and products, and emphasis on waste utilization are also being explored in conjunction with research on catalytic utilization of syngas and other gases (including CO2). Industry-relevant parameters are given deliberate attention as part of the work done under this project to help answer questions important for future commercialization and address associated risks.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Chapter 14: Sustainable Biomass Conversion Process Assessment

Process intensification and integration for sustainable design play an essential role in addressing and alleviating severe sustainable development challenges. It is prudent to evaluate a process design in its early stage development to ensure the process can achieve sustainability goals. The primary goal of a sustainability evaluation is to assess the impact of systems on areas sought to be protected and maintained over time, such as human well-being and ecosystems (Schaubroeck, T. and Rugani, B. (2017). A revision of what life cycle sustainability assessment should entail: towards modeling the net impact on human well-being. Journal of Industrial Ecology 21 (6): 1464-1477). Parenthetically, sustainable process design to convert biomass to fuels and chemicals plays an integral part in the bioeconomy sustainability. It is recognized that the integration of sustainability in process design is core to the mission in developing renewable fuels and should be considered a necessary practice in biorefinery design. This study demonstrates the use of Gauging Reaction Effectiveness for ENvironmental Sustainability of Chemistries with a multi-Objective Process Evaluator (GREENSCOPE) as a tool to help track progress on process sustainability performance attributed to conversion improvement. With the incorporation of a wide range of indicators, GREENSCOPE captures the multi-dimensional aspect of the process design and operation. As opposed to conventional techno-economic analysis and life cycle assessment (in which the focuses are limited to economic and environmental aspects), GREENSCOPE enables the consideration of process intensification and integration for sustainable design. A high-octane gasoline production from woody biomass feedstock is used as a case study to demonstrate the approach.

biomass↗
DOE OSTI2021

Spectroscopic insight into carbon speciation and removal on a Cu/BEA catalyst during renewable high-octane hydrocarbon synthesis

Conversion of methanol and dimethyl ether (DME) to high-octane gasoline catalyzed by beta zeolite (BEA) provides an opportunity for the production of high-quality fuels from renewable carbon sources (e.g., gasified biomass). Recent research demonstrated that a Cu-modified BEA zeolite catalyst (Cu/BEA) offered advantages over the unmodified BEA catalyst due to multifunctional Cu species that enabled incorporation of co-fed H2, reactivation of light alkanes, and reduction of products from the aromatic hydrocarbon pool. The shift in hydrocarbon pool chemistry has the potential to influence the identity and relative composition of surface carbon species that are often linked to deactivation. A detailed understanding of these carbon species is important to develop an effective and efficient regeneration procedure that can enable the transition from fundamental catalyst development to commercial application. Here, we applied complementary ex situ and in situ characterization techniques to compare the structures of surface carbon species on post-reaction Cu/BEA and unmodified BEA catalysts. Both catalysts contained acyclic and aromatic hydrocarbons along with graphitic carbon species. However, the post-reaction Cu/BEA catalyst had a lower polycyclic aromatic content, and further, the graphitic species were more hydrogenated and defective. It was also found that the presence of Cu promoted carbon removal at lower temperatures than for unmodified BEA through activation of O2 by Cu oxide during thermal oxidation. The fundamental insight into the composition of surface carbon species enabled the design of an effective and efficient regeneration strategy for the DME homologation reaction over Cu/BEA, resulting in full recovery of the catalyst activity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1979

Coal liquefaction to increase jet fuel production

Processing concept that increases supply of jet fuel has been developed as part of study on methods for converting coal to hydrogen, methane, and jet fuel. Concept takes advantage of high aromatic content of coal-derived liquids to make high-octane gasoline, instead of destroying aromatics to make jet fuel.

Source record↗
DOE OSTI2021

BETO 2021 Peer Review - Advanced Catalyst Synthesis and Characterization (ACSC) Project WBS 2.5.4.304; 303; 305

The Advanced Catalyst Synthesis and Characterization (ACSC) project, in close collaboration with the Chemical Catalysis for Bioenergy (ChemCatBio) Consortium enabling projects, CatCost, and the Engineering of Catalyst Scale-Up project, (1) provides fundamental insight into working catalysts leading to actionable recommendations for all of the ChemCatBio catalysis projects, (2) addresses overarching catalysis challenges central to the ChemCatBio Consortium, and (3) adapts and applies new synthesis methodologies and in situ/operando characterization capabilities to meet the evolving needs of the catalysis projects. The outcome is a transition from empirical catalyst development to rational design through the prediction of materials with targeted properties based on advanced characterization combined with computational modeling, and the synthesis of next generation catalysts with predicted structures that yield demonstrated improvements in catalytic performance. In FY18, the ACSC helped to demonstrate the utility of the complete catalyst and process development cycle for dimethyl ether to high-octane gasoline over metal-modified zeolite catalysts for the Upgrading of C1 Building Blocks project, and in FY21 will leverage capabilities, expertise, and computational models established for this effort to target next-generation catalysts for ethanol to distillates for the Upgrading of C2 Intermediates project with enhanced performance in half the time.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

A Full Spectrum of Characterization for Insight into Carbon Speciation and Removal on a Cu/BEA Catalyst During Renewable High-Octane Hydrocarbon Synthesis

Conversion of methanol and dimethyl ether to high-octane gasoline catalyzed by beta zeolite (BEA) provides an opportunity for the production of high-quality fuels from renewable carbon sources (e.g., gasified biomass). Recent research demonstrated that a Cu-modified BEA zeolite catalyst (Cu/BEA) offered advantages over the unmodified BEA catalyst due to multifunctional Cu species that enabled incorporation of co-fed H2, reactivation of light alkanes, and reduction of products from the aromatic hydrocarbon pool. The shift in hydrocarbon pool chemistry has the potential to influence the identity and relative composition of surface carbon species that are often linked to deactivation. A detailed understanding of these carbon species is important to develop an effective and efficient regeneration procedure that can enable the transition from fundamental catalyst development to commercial application. Here, we applied complementary ex situ and in situ characterization techniques to compare the structures of surface carbon species on post-reaction Cu/BEA and unmodified BEA catalysts. Both catalysts contained acyclic and aromatic hydrocarbons along with graphitic carbon species. However, the post-reaction Cu/BEA catalyst had a lower polycyclic aromatic content, and further, the graphitic species were more hydrogenated and defective. It was also found that the presence of Cu promoted carbon removal at lower temperatures than for unmodified BEA through activation of O2 by Cu during thermal oxidation. The fundamental insight into the composition of surface carbon species enabled the design of an effective and efficient regeneration strategy for the DME homologation reaction over Cu/BEA, resulting in full recovery of the catalyst activity.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Rapid prediction of fuel research octane number and octane sensitivity using the AFIDA constant-volume combustion chamber

Current research octane number (RON) and motor octane number (MON) gasoline performance characterization techniques use dated, complex engine testing methodology and limit researchers’ ability to easily characterize small volumes of experimental fuels. A novel methodology is presented that correlates measured ignition delay (ID) time to RON in an Advanced Fuel Ignition Delay Analyzer (AFIDA) constant-volume combustion chamber device at a single pressure/temperature condition, with an r2 of 0.99 and standard error (SE) of 1.0. The correlation of the slope of the ID time between two additional temperature points to octane sensitivity (S) produces an r2 of 0.97 and SE of 0.69; however, fuels with S>12 are indistinguishable. These results are based on methodology calibration using 31 primary and toluene reference fuels containing 0%-40% ethanol with RON values ranging from 85 to 113. Validation of these methods using a 102-sample fuel matrix spanning an array of base fuels and additive chemistry designed to test the robust applicability of the method, along with pump gasoline and high-octane surrogate blend samples, demonstrates an r2 of 0.94 and SE of 1.3 for the RON correlation over all samples, whereas the equivalent S correlation produces an r2 of 0.78 and SE of 1.2 by excluding two additives, 3-pentanone and diisobutylene, which displayed poor S correlation results. This novel AFIDA analysis method can be performed in 1 h and with 40 mL of fuel, offering significant improvements in time and volume requirements over traditional techniques.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Free-spray characteristics and spray-wall interactions of methanol on a gasoline direct injector under flash-boiling and non-flash-boiling conditions

Methanol is considered a promising alternative fuel for internal combustion engines (ICEs) due to its high-octane number, fast laminar flame speed, and elevated latent heat of vaporization, all of which support higher compression ratios and improved thermal efficiency. However, its substantial latent heat of vaporization also poses cold-start challenges, such as misfire and fuel film deposition. This study aims to investigate methanol spray morphology and spray-wall interaction using the Spray M injector from the Engine Combustion Network within a constant-pressure flow vessel. A recently developed unified numerical framework capable of modeling both flash and non-flash boiling sprays is validated against experimental liquid volume fraction data acquired via 3-D computed tomography. Here, the results reveal that flash boiling significantly alters the spray morphology, leading to smaller droplets and spray collapse due to enhanced air-entrainment-induced turbulence. Quantitative agreement between experiments and simulations confirms this behavior. Coupled 0-D equilibrium and 3-D computational fluid dynamics analyses show that flash boiling accelerates evaporation and reduces fuel residence time, while non-flash conditions maintain a persistent liquid core more susceptible to wall wetting. Wall temperature diagnostics reveal that spray collapse alters heat transfer patterns by shifting cooling effects. Mixture fraction analysis indicates that evaporation is primarily governed by shear-layer turbulence, though deviations from adiabatic equilibrium mixing emerge under low-turbulence conditions. Finally, increasing fuel, ambient, and wall temperatures reduces wall wetting and film thickness, mitigating cold-start risks. These findings enhance the understanding of methanol sprays’ behavior and support its adoption as a viable, alternative fuel for ICEs.

Engine Combustion Network↗
DOE OSTI2024

Potential Adoption and Benefits of Co-Optimized Multimode Engines and Fuels for U.S. Light-Duty Vehicles

Exploring a diverse portfolio of technologies for decarbonization is crucial to understanding the potential impacts of different technological solutions and their associated environmental implications. Using high-octane, high-sensitivity biofuel blends in co-optimized multimode engines can increase engine efficiency and reduce vehicle emissions. Here, the multimode engine research focuses on the benefits of light-duty vehicle engines, which can operate in multiple modes depending on the vehicle's load. Low-temperature combustion can improve efficiency and reduce emissions (such as those from oxides of nitrogen and particulate matter) during low-load operation, while spark ignition performance is maintained in high-load operation. These advanced engines can be optimized to run on blends of biobased fuels. This analysis models scenarios for potential market adoption of co-optimized multimode vehicles fueled by three different bioblendstocks: ethanol, isopropanol, and isobutanol. An integrated modeling approach is used to forecast the energy and environmental impacts of the deployment of co-optimized multimode vehicles and fuels in the light-duty sector over the 2020-to-2050 time horizon. The multidisciplinary approach combines vehicle sales modeling, system dynamics modeling of the biorefining industry, and life cycle assessment to estimate the emissions and energy benefits. The models consider market forces such as consumer preferences for vehicle attributes, biofuel supply and demand dynamics subject to biorefinery capacity build-out and bioresource constraints, and forecasted changes to the U.S. bulk energy system over time. Market adoption of co-optimized vehicles is evaluated across a wide parameter space for incremental vehicle cost and engine efficiency improvement. This analysis reveals that the deployment of co-optimized multimode fuels and vehicles results in up to a 5% reduction in annual sector-wide life cycle greenhouse gas (GHG) emissions by 2050, relative to a business-as-usual scenario, but is also indicates environmental trade-offs, such as higher life cycle water-use. Emission benefits could potentially increase beyond 2050, as the new technologies penetrate the market and gain a foothold. Results also show that, under certain circumstances, vehicles with engines co-optimized for use with high-octane, high-sensitivity biofuel blends can be cost-competitive with conventional gasoline, while reducing GHG emissions. Our modeling results indicate that co-optimized multimode fuels and engines can be strategically leveraged in tandem with electrification to decarbonize the light-duty sector. Co-optimized vehicles could play a role in the early years of the time horizon, while electric vehicles (EVs) could become more competitive in the later years, highlighting the complementary benefits of these technologies for GHG reductions.

Oke, Doris↗
NASA NTRS1943

The Measurement of Fuel-air Ratio by Analysis of the Oxidized Exhaust Gas

An investigation was made to determine a method of measuring fuel-air ratio that could be used for test purposes in flight and for checking conventional equipment in the laboratory. Two single-cylinder test engines equipped with typical commercial engine cylinders were used. The fuel-air ratio of the mixture delivered to the engines was determined by direct measurement of the quantity of air and of fuel supplied and also by analysis of the oxidized exhaust gas and of the normal exhaust gas. Five fuels were used: gasoline that complied with Army-Navy Fuel Specification, No. AN-VV-F-781 and four mixtures of this gasoline with toluene, benzene, and xylene. The method of determining the fuel-air ratio described in this report involves the measurement of the carbon-dioxide content of the oxidized exhaust gas and the use of graphs or the presented equation. This method is considered useful in aircraft, in the field, or in the laboratory for a range of fuel-air ratios from 0.047 to 0.124

FUELS-TOLUENE↗