Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high speed microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Stereoscopic high-speed microscopy to understand transient internal flow processes in high-pressure nozzles

The flow and cavitation behavior inside fuel injectors is known to affect spray development, mixing and combustion characteristics. We discuss that while diesel fuel injectors with converging and hydro-eroded holes are generally known to limit cavitation and feature higher discharge coefficients during the steady period of injection, less is known about the flow during transient periods corresponding to needle opening and closing. Multiple injection strategies involve short injections, multiplying these aspects and giving them a growing importance as part of the fuel delivery process. In this study, single-hole transparent nozzles were manufactured with the same hole inlet radius and diameter as the Engine Combustion Network Spray D nozzle, mounted to a modified version of a common-rail Spray A injector body and needle. Needle opening and closing periods were visualized with stereoscopic high-speed microscopy at injection pressures relevant to modern diesel engines. Time-resolved sac pressure was extracted via elastic deformation analysis of the transparent nozzles. Sources of cavitation were observed and tracked, enabling the identification of a gas exchange process after the end of injection with ingestion of chamber gas into the sac and orifice. We observed that the gas exchange contributed widely to disrupting the start of injection and outlet flow during the subsequent injection event.

42 ENGINEERING↗

High-speed nanoscale characterization of dewetting via dynamic transmission electron microscopy

The dewetting of thin films can occur in either the solid or the liquid state for which different mass transport mechanisms are expected to control morphological changes. Traditionally, dewetting dynamics have been examined on time scales between several seconds to hours, and length scales ranging between nanometers and millimeters. The determination of mass transport mechanisms on the nanoscale, however, requires nanoscale spatial resolution and much shorter time scales. This study reports the high-speed observation of dewetting phenomena for kinetically constrained Ni thin films on crystalline SrTiO{sub 3} substrates. Movie-mode Dynamic Transmission Electron Microscopy (DTEM) was used for high-speed image acquisition during thin film dewetting at different temperatures. DTEM imaging confirmed that the initial stages of film agglomeration include edge retraction, hole formation, and growth. Finite element modeling was used to simulate temperature distributions within the DTEM samples after laser irradiation with different energies. For pulsed laser irradiation at 18 μJ, experimentally observed hole growth suggests that Marangoni flow dominates hole formation in the liquid nickel film. After irradiation with 13.8 μJ, however, the observations suggest that dewetting was initiated by nucleation of voids followed by hole growth through solid-state surface diffusion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A serial-kinematic nanopositioner for high-speed atomic force microscopy

A flexure-guided serial-kinematic XYZ nanopositioner for high-speed Atomic Force Microscopy is presented in this paper. Two aspects influencing the performance of serial-kinematic nanopositioners are studied in this work. First, mass reduction by using tapered flexures is proposed to increased the natural frequency of the nanopositioner. 25% increase in the natural frequency is achieved due to reduced mass with tapered flexures. Second, a study of possible sensor positioning in a serial-kinematic nanopositioner is presented. An arrangement of sensors for exact estimation of cross-coupling is incorporated in the proposed design. A feedforward control strategy based on phaser approach is presented to mitigate the dynamics and nonlinearity in the system. Limitations in design approach and control strategy are discussed in the Conclusion.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The effects of carbonaceous inclusions and their distributions on dynamic failure processes in boron carbide ceramics

Commercially available boron carbide ceramics typically have heterogeneous microstructures that contain distributions of processing-induced inclusions. The inclusions that are rich in carbon (i.e., carbonaceous) govern the underlying mechanisms of brittle fracture through wing crack formation, and thus dictate the mechanical response of the ceramic. In this study, we investigate the dynamic failure of five boron carbide ceramic materials with different inclusion populations. All of the materials were prepared by hot-pressing; four of these boron carbides contained different sizes and concentrations of carbonaceous inclusions, while one contained no carbonaceous inclusions. The heterogeneity distributions were characterized in some detail for statistical analysis using scanning electron microscopy and quantitative image analysis. A modified compression Kolsky bar setup with in situ ultra-high-speed microscopic imaging (10 million frames per second) was then used to study the influence of the inclusion distributions on the dynamic failure processes in these materials, at nominal high strain rates of 10 2 -10 3 s -1 . The in situ ultra-high-speed microscopy highlighted the link between micro and macroscale failure processes and demonstrated that the carbonaceous inclusions are indeed the preferential sites for nucleation of wing cracks, as previously hypothesized based on post-mortem observations. The relative orientation of an inclusion with respect to the compression axis was shown to affect the likelihood that it would participate in crack nucleation. In conclusion, all of the ceramics were also found to have orientation-dependent peak compressive stress, regardless of the presence of carbonaceous inclusions, suggesting that grain orientation distributions are also important.

36 MATERIALS SCIENCE↗

High speed quantitative digital microscopy

Modern digital image processing hardware makes possible quantitative analysis of microscope images at high speed. This paper describes an application to automatic screening for cervical cancer. The system uses twelve MC6809 microprocessors arranged in a pipeline multiprocessor configuration. Each processor executes one part of the algorithm on each cell image as it passes through the pipeline. Each processor communicates with its upstream and downstream neighbors via shared two-port memory. Thus no time is devoted to input-output operations as such. This configuration is expected to be at least ten times faster than previous systems.

Castleman, K. R.↗

SAF Combustion & Soot Processes [Slides]

The atomization, mixing, combustion and emissions characteristics of aviation fuels were measured using a novel approach based on a non-continuous injection scheme called the single-hole atomizer (SHA). High-speed microscopy revealed differences between fuels in terms of evaporation and mixing regimes over conditions relevant to modern and next generation aero-engine combustors. Measurements of liquid and vapor penetration, mixing fields, combustion and emissions metrics (ignition delay, lift-off length, PAH formation, soot mass) highlighted the effects of fuels and combustor conditions. The experimental results are being leveraged to adjust and validate chemical and CFD models. Detailed analysis of sampled soot showed subtle differences in soot morphology between fuels. The results revealed the presence of contaminants potentially affecting surface chemistry and the nucleation propensity of water droplets on particles. Chemical mechanisms for NJFCP A-2, C-1 and C-4 showed good performance over a large parameter space. Spray breakup at relight conditions is vastly different from the atomization observed at high pressure. CFD simulations of the SHA target conditions confirmed the good behavior of the C-1 kinetic mechanism. The simulations support the strong relationship between low and high temperature reactions. New altitude chamber facility to enable detailed characterization of the heterogeneous nucleation process of water on aerosol particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Visualization of the evolution of charged droplet formation and jet transition in electrostatic atomization

A detailed experimental study on the evolution of charged droplet formation and jet transition from a capillary is reported. By means of high-speed microscopy, special attention has been paid to the dynamics of the liquid thread and satellite droplets in the dripping mode, and a method for calculating the surface charge on the satellite droplet is proposed. Jet transition behavior based on the electric Bond number has been visualized, droplet sizes and velocities are measured to obtain the ejection characteristic of the spray plume, and the charge and hydrodynamic relaxation are linked to give explanations for ejection dynamics with different properties. The results show that the relative length is very sensitive to the hydrodynamic relaxation time. The magnitude of the electric field strength dominates the behavior of coalescence and noncoalescence, with the charge relationship between the satellite droplet and the main droplet being clear for every noncoalescence movement. Ejection mode transitions mainly depend on the magnitude of the electric Bond number, and the meniscus dynamics is determined by the ratio of the charge relaxation time to the hydrodynamic relaxation time.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optical knife-edge displacement sensor for high-speed atomic force microscopy

We show that an optical knife-edge technique can be used to detect the parallel shift of an object with sub-nanometer resolution over a wide bandwidth. This allows to design simple, contact-free, and high-speed displacement sensors that can be implemented in high-speed atomic force microscope scanners. In an experimental setup, we achieved a root-mean-square sensor noise of 0.8 nm within a bandwidth from 1 Hz to 1.1 MHz. We used this sensor to detect and correct the nonlinear z-piezo displacement during force curves acquired with rates of up to 5 kHz. We discuss the fundamental resolution limit and the linearity of the sensor.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-speed atomic force microscopy reveals structural dynamics of α-synuclein monomers and dimers

We report that α-Synuclein (α-syn) is the major component of the intraneuronal inclusions called Lewy bodies, which are the pathological hallmark of Parkinson’s disease. α-Syn is capable of self-assembly into many different species, such as soluble oligomers and fibrils. Even though attempts to resolve the structures of the protein have been made, detailed understanding about the structures and their relationship with the different aggregation steps is lacking, which is of interest to provide insights into the pathogenic mechanism of Parkinson’s disease. Here we report the structural flexibility of α-syn monomers and dimers in an aqueous solution environment as probed by single-molecule time-lapse high-speed AFM. In addition, we present the molecular basis for the structural transitions using discrete molecular dynamics (DMD) simulations. α-Syn monomers assume a globular conformation, which is capable of forming tail-like protrusions over dozens of seconds. Importantly, a globular monomer can adopt fully extended conformations. Dimers, on the other hand, are less dynamic and show a dumbbell conformation that experiences morphological changes over time. DMD simulations revealed that the α-syn monomer consists of several tightly packed small helices. The tail-like protrusions are also helical with a small β-sheet, acting as a “hinge”. Monomers within dimers have a large interfacial interaction area and are stabilized by interactions in the non-amyloid central (NAC) regions. Additionally, the dimer NAC-region of each α-syn monomer forms a β-rich segment. Moreover, NAC-regions are located in the hydrophobic core of the dimer.

59 BASIC BIOLOGICAL SCIENCES↗

Ultra-high vacuum compatible optical chopper system for synchrotron x-ray scanning tunneling microscopy

High-speed beam choppers are a crucial part of time-resolved x-ray studies as well as a necessary component to enable elemental contrast in synchrotron x-ray scanning tunneling microscopy (SX-STM). However, many chopper systems are not capable of operation in vacuum, which restricts their application to x-ray studies with high photon energies, where air absorption does not present a significant problem. To overcome this limitation, we present a fully ultra-high vacuum (UHV) compatible chopper system capable of operating at variable chopping frequencies up to 4 kHz. The lightweight aluminum chopper disk is coated with Ti and Au films to provide the required beam attenuation for soft and hard x-rays with photon energies up to about 12 keV. The chopper is used for lock-in detection of x-ray enhanced signals in SX-STM.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗