SEARCH · Engineering Papers
Results for “hammers”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Correcting distortions of thin-walled machined parts by machine hammer peening
Thin-walled aerostructural components frequently get distorted after the machining process. Reworking to correct distortions or eventually rejecting parts significantly increases the cost. This paper proposes a new approach to correct distortions in thin-walled components by strategically applying hammer peening on target surfaces of a machined component. Aluminium alloy 7475-T7351 was chosen for this research. The study was divided in two stages. First, the residual stresses (RS) induced by four different pneumatic hammer peening conditions (modifying the stepover distance and initial offset) were characterised in a test coupon, and one of the conditions was selected for the next stage. In the second stage, a FEM model was used to predict distortions caused by machining in a representative workpiece. Then, the RS induced by hammer peening were included in an FEM model to define two hammer peening strategies (varying the coverage area) to analyse the capability to reduce distortions. Two workpieces were machined and then treated with the simulated hammer peening strategies for experimental validation. Results in the test coupon showed that pneumatic hammer peening can generate high compressive RS (-50 to –350 MPa) up to 800 μm depth, with their magnitude increasing with a reduced stepover distance. Application of hammer peening over 4% of the surface of the representative workpiece reduced the machining-induced distortions by 37%, and a coverage area of 100% led to and overcorrection by a factor of five. This confirms that hammer peening can be strategically applied (in target areas and changing the percentage of coverage) to correct low or severe distortions.
Value proposition of coatings or new alloys on hammer wear
The goal of this Case Study was to elucidate the value of improving of the life of parts that wear within a system in terms of the additional material cost that it takes to reach the level of improvement. We recognize that the failure limits and system performance are representative of a single system that may or may not exist in the real world, however, our goal of this project was not to provide an answer for a specific system or to provide a full understanding the economics of all potential systems. The analysis was performed using relative changes from the base alloy cost and considered relative improvements in part life in order to generalize the comparison without referencing specific alloys or coatings that might be employed. Ultimately, this work provides a first check of the potential for improving wear characteristics of grinder hammers to provide a meaningful and impactful benefit to biomass preprocessing and conversion systems. Key takeaways include: • Increasing the life of hammers by 3× provides a delivered feedstock cost benefit of approximately $\$2.25$/dry ton assuming that the relative cost of the hammer material of construction is not increased. • The feasible area of relative hammer cost increase ranges from 110% to 122% of the relative life increase, i.e., a 3× life increase can cost 3.66× the cost of the original hammers • Beyond a 3× increase in relative hammer life, little economic benefit is realized • Even when moisture impacts are included, the relationship between relative hammer cost and relative hammer life was reduced only slightly to a range of 108% to 116% • From the simulation we would expect delivered feedstock costs to be within ±$1.10/dry ton, based on the uncertainty analysis
Application of an Erosion Wear Model to Predict Wear of Hammer Milling Components
A workable analytical erosion model that relates critical hammermill process parameters (hammermill geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear (more specifically, change in the shape of hammers) in hammer milling operations. Results of the model were compared to experimental observations of the shape of hammers used in the INL Stage 1 Vermeer hammermill. Results showed good agreement between predicted and measured shape of the hammer, and that a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.
Techno-economic analysis comparison of comminution of wood chips using a hammer mill and a rotary shear
Preprocessing is a crucial step in the utilization of biomass feedstocks for the production of fuel and biomaterials [1]. Size reduction and drying of the material, where used, are two of the most costly and energy intensive operations that are undertaken during preprocessing, reduction of the energy usage during these two phases will reduce cost of processing and ultimately reduce the overall cost to the final user. Traditionally, a hammer mill has been the primary method used for secondary size reduction. For wet material, a hammer mill requires high amounts of energy, while for dry material the hammer mill produces a large quantity of small particles [2]. In both cases, the costs increase either from additionally needed fuel cost or from the cost of lost material. In effort to lower the cost for size reduction, a rotary shear has been developed for the comminution of biomass feedstocks. The rotary shear utilizes interlocking, rotating disk that shear the material rather than using impact to reduce the particle size of the materials. Because the material is size reduced using a cutting motion, rather than impact, the distribution of particle sizes is much narrower than produced by hammer mills.
Auto Indexer for Percussive Hammers Final Report
Geothermal energy has been underutilized in the U.S., primarily due to the high cost of drilling in the harsh environments encountered during the development of geothermal resources. Drilling depths can approach 5,000 m with temperatures reaching 170 C. In situ geothermal fluids are up to ten times more saline than seawater and highly corrosive, and hard rock formations often exceed 240 MPa compressive strength. This combination of extreme conditions pushes the limits of most conventional drilling equipment. Furthermore, enhanced geothermal systems are expected to reach depths of 10,000 m and temperatures more than 300 °C. To address these drilling challenges, Sandia developed a proof-of-concept tool called the auto indexer under an annual operating plan task funded by the Geothermal Technologies Program (GTP) of the U.S. Department of Energy Geothermal Technologies Office. The auto indexer is a relatively simple, elastomer-free motor that was shown previously to be compatible with pneumatic hammers in bench-top testing. Pneumatic hammers can improve penetration rates and potentially reduce drilling costs when deployed in appropriate conditions. The current effort, also funded by DOE GTP, increased the technology readiness level of the auto indexer, producing a scaled prototype for drilling larger diameter boreholes using pneumatic hammers. The results presented herein include design details, modeling and simulation results, and testing results, as well as background on percussive hammers and downhole rotation.
Impact of anatomical fractionation of corn stover on hammer mill throughput and energy consumption
The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on loss of very wet stover that causes failures in the first stage grinder and that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbohydrate content (minimum total carbohydrate specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed stover not meeting the total carbohydrate specification to the conversion reactor. Laboratory data on the impacts of moisture content and tissue fraction on throughput and energy consumption in a stage 2 hammer mill were received from FCIC Subtask 5.1. Additional air classifier throughput, energy consumption and separation efficiency data were obtained from FCIC Subtask 5.1 for the new air classifier, which has three exit streams (lights, middle and heavies). These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents and particle sizes had not been analyzed in the laboratory at the time of the model runs, we assumed that the ash distributed proportionally with total mass into the lights and heavies in an air classifier having two exit streams (lights and heavies) and that the lights fraction from the air classifier was not removed. Key takeaways from this Case Study are that due to lower energy consumption, it is more cost effective to hammer mill fractionated corn stover tissues than whole stover. Reduction of grinding energy was significant and may possibly be connected to particle-particle interactions in the grinder that lead to increased residence time of leaves and husks, resulting in decreased throughput and higher generation of fines when milling whole stover. While we did not see significant impacts to throughput, this was due to moisture failures of the first stage grinder in each system dominating failures and downtime. The operating cost savings of reduced grinding energy savings in the second stage hammer mills alone was high enough to offset the added capital cost of the air classifier and extra grinding line.
High-moisture pelleting of corn stover using pilot- and commercial-scale systems: Impact of moisture content, L / D ratio and hammer mill screen size on pellet quality and energy consumption
Here, high-moisture pelleting of corn stover was tested in pilot- and commercial-scale systems. For the pilot-scale study, a 6.35 mm screen size hammer mill ground corn stover was reconditioned to moisture between 14 and 29.6% (w.b.), and 5, 7 and 9 L/D ratio pellet die were used. At 29% corn stover moisture content and L/D ratios of 5 and 9, the bulk density and durability of the pellets were ≤450 kg/m 3 and <90% and >540 kg/m 3 and >90%, respectively. Increasing the feedstock moisture and L/D ratio increased the pelleting energy. Increasing the hammer mill screen size to 11.11 mm reduced the bulk density but not the durability. The response surface models adequately described the pelleting process (R 2 ≥ 0.88), and analysis of variance showed a strong interaction between the process variables and pellet properties. Commercial-scale testing of high-moisture pelleting using 6.35 mm ground corn stover bales in the moisture range 24–26% (w.b.) produced pellets with a density of >675 kg/m 3 and durability of >98%, whereas increasing the hammer mill screen size to 11.11 mm reduced the bulk density by about 100 kg/m 3 but not the durability. The energy consumption of the commercial-scale unit operations for the high-moisture pelleting process was in the range 98–124 kW h/ton, which is 64–72% less energy than conventional pelleting that requires energy about 350 kW h/ton for biomass drying from 30% (w.b.) to 10% (w.b.) moisture content before pelleting. Pellets produced using high-moisture pelleting met International Organization for Standardization and Pellets Fuel Institute international standards. Published 2023. This article is a U.S. Government work and is in the public domain in the USA.
Feeding properties and behavior of hammer- and knife-milled pine
This work reports the rheological characterization of hammer and knife-milled lodgepole pine materials as a function of grind size and moisture content. Characterizations included particle size and shape distributions, bulk density, compressibility at 10 kPa uniaxial pressure, elastic recovery from 10 kPa uniaxial pressure, shear strength, effective angle of internal friction, arching in a custom hopper, and feeding performance in volumetric and gravimetric auger feeders. Particle analysis indicates that the width and length distributions of the 3 mm hammer-milled and the 6 mm knife-milled materials are quite similar, and that all the materials have relatively short aspect ratios (< 4). Compressibility and elastic recovery both increased with increasing moisture content with both values increasing more than 10% and the effect being most severe for the 3 mm grind. Adding 3 kPa of pressure increased the critical arching width for all hopper arching tests, except for the 25 mm grind material with 20% MC, for which the critical arching width actually decreased with increased pressure. Interestingly, for materials with smaller particle sizes, the volumetric feed rate tends to decrease as moisture increases even though the density of the material increases with moisture content and the auger speeds are the same. Time variability of volumetric feed rate increased dramatically with increasing particle size but the impact of moisture content was not as clear. For nearly all tests, gravimetric auger feeding resulted in better feeding control and substantially decreased time variability in the material feed rate. These tests show that material feed rate and volumetric auger feed rate variability are dependent upon material shear strength, bulk density, and particle size. Shear tests indicate that material strength generally decreased with increasing particle size, although the impact of moisture was not entirely consistent.
Episodic Magma Hammers for the 15 January 2022 Cataclysmic Eruption of Hunga Tonga‐Hunga Ha'apai
Understanding the forces and magma system dynamics on timescales of seconds to minutes remains challenging. In the January 2022 phreatoplinian Hunga Tonga-Hunga Ha'apai eruption, four remarkably similar seismic subevents within a 5-min interval occurred during the intensifying early eruptive phase. The subevents are similar in waveforms and durations (~25 s each). Each subevent begins with an unusual negative P-wave polarity which is inferred, using full-wave seismic modeling, to be caused by an upward single-force mechanism at the volcano created by a magma hammer likely in response to magma flow blockage/constriction during the early part of the eruption as discharge rapidly increased over orders of magnitude with concomitant conduit geometry evolution and instability. Our proposed episodic magma hammer model is consistent with thermodynamic and phase properties of the magmatic mixture, and yields an estimate of conduit mass flow in agreement with vent discharge rates derived from satellite imagery of plume heights.
Impact of Anatomical Fractionation of Corn Stover on Hammer Mill Throughput and Energy Consumption
The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on loss of very wet stover that causes failures in the first stage grinder and that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbohydrate content (minimum total carbohydrate specification), maximum ash content and the delivered feedstock cost impacts of not being able to feed stover that did not meet the total carbohydrate specification to the conversion reactor. Laboratory data on the impacts of moisture content and tissue fraction on throughput and energy consumption in a stage 2 hammer mill were received from FCIC Subtask 5.1: Preprocessing, Corn Stover Preprocessing (Neal Yancey and Sergio Hernandez, INL). Additional air classifier throughput, energy consumption and separation efficiency data were obtained from FCIC Subtask 5.1 (Neal Yancey, INL) for the new air classifier, which has three exit streams (lights, middle and heavies). These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents and particle sizes had not been analyzed in the laboratory at the time of the model runs, we assumed that the ash distributed proportionally with total mass into the lights and heavies in an air classifier having two exit streams (lights and heavies) and that the lights fraction from the air classifier was not removed.
Improvement of Drop‐Hammer Impact Testing for Safety Assessment of High Explosives Using 10‐mg Samples
Here, in this study, we established an improved method for drop-hammer impact testing of small quantities of high explosives (10 mg). We performed about seven hundred impact tests under various experimental conditions (e.g., sandpaper vs bare anvil, different sample masses, drop-weights, and striker diameters) to determine an optimal set of conditions and reaction detection methods (e.g., gas analysis, video, and sound recordings) that give the most statistically reliable results with 10 mg samples. We used both Frequentist and Bayesian statistical approaches to compare estimates of the drop height (DH50) that initiates a reaction 50% of the time, and to quantify the associated uncertainty. Gas analysis proved to be the most reliable reaction detection method, showing unambiguous rises in HE decomposition products (e.g., CO 2 ) even when the other indicators (e.g., sound, video) were inconclusive. The impact tests performed with a bare anvil showed much better reproducibility than those conducted with sandpaper, reducing the largest uncertainty observed in the data sets by a factor of 1.7. The DH 50 values obtained from three different sample masses (10, 20, and 35 mg) fell within the uncertainties of the measurements. We demonstrated the improved procedure (i.e., 10-mg samples, gas analysis, bare anvil, and Bayesian approach) on a variety of PETN samples having different surface areas and thermal histories.
Material Characterization-Based Wear Mechanism Investigation for Biomass Hammer Mills
Biomass, as harvested, is composed of inorganic compounds both intrinsically and extrinsically and can be abrasive. The present study investigates the wear modes and mechanisms of two types of blades of hammer mills used in biomass size reduction (impacting the particle size and distribution) and densification (impacting the size, shape, and density). The dominant wear modes for the stage 1 steel blades are determined to be erosive and polishing wear. For the stage 2 blades with a carbide weld overlay, the main wear mechanisms are erosion and fracture. Partial replacement of Co by Fe in the outer layer of the carbide grits, likely induced by diffusion during high-temperature welding, has been correlated to the observed microcracking. Finally, the microcracking is believed to weaken the grit strength and fracture toughness to make the overlay prone to fracture and erosion due to repetitive contact with the inorganic contents in chopping biomass.
Building a Next Generation Seismic Hammer™ to Improve Ground-Based Nuclear Detonation Detection
HK Exploration proposes to build a next generation of Seismic Hammer™, a rapidly deployed, self-mobile, repeatable, high-energy, impulsive mechanical seismic / infrasound source.
Joining Dissimilar Materials via Rotational Hammer Riveting Technique
A mechanically robust joining method for Mg/Al and Mg/CFRP could enable multi-material assemblies that decrease vehicle weight while offering more flexibility for designers. However, certain challenges exist for joining Mg/Al and Mg/CFRP. Mechanical joining, such as conventional riveting, clinching and bolting do not form a metallurgical bond between the fastener and metal sheet being fastened. Large differences in physical and mechanical properties of metals and polymers make joining Al or Mg to CFRP challenging via various welding techniques. With solid-state and fusion based welding, rapid formation of brittle intermetallic compounds at the Mg/Al interface lead to interfacial fracture under mechanical loading. In this study, a Rotational Hammer Rivet (RHR) technique was developed to fabricate Mg/CFRP and Mg/Al joints. With RHR technique, direct joining between Mg/Al and Mg/CFRP were replaced by joining Mg rivet head and top Mg sheet. Through heat generated by plastic deformation of an Mg rivet, RHR creates a metallurgical bond between rivet head and Mg sheet which seals corrosive electrolyte from penetrating around the rivet head.
Sandia and Ditch Witch Technology Commercialization Fund Integral Motor and Percussive Hammer
This report captures the results of development and testing of a integral downhole motor and percussive hammer used for drilling in near-surface hard rock formations. The work was funded through the DOE Office of Technology Transitions Technology Commercialization Fund. It was a collaboration between Sandia National Labs and The Charles Machine Works (aka Ditch Witch). In the collaboration, Sandia developed a pneumatic motor derived from an indexing tool used in other drilling applications, and Ditch Witch developed the bearing pack tied to the output shaft of the motor as well as the angled beacon housing used for directional control.
Value Proposition of Coatings or New Alloys on Hammer Wear
The goal of this Case Study was to compare the cost savings from improving the life span of parts that wear within a system to the additional material cost required to reach varying levels of improved life span. We recognize that the failure limits and system performance are representative of a single system that may or may not exist in the real world, however, our goal for this analysis was not to provide an answer for a specific system or to provide a full understanding the economics of all potential systems. The analysis was performed using relative changes from the base alloy cost and considered relative improvements in part life in order to generalize the comparison without referencing specific alloys or coatings that might be employed. Ultimately, this work provides a first check of the potential for improving wear characteristics of grinder hammers to provide a meaningful and impactful benefit to biomass preprocessing and conversion systems.
Das ist der HAMMER: consistent new physics interpretations of semileptonic decays
Abstract Precise measurements of $$b\rightarrow c\tau \bar{\nu }$$ b → c τ ν ¯ decays require large resource-intensive Monte Carlo (MC) samples, which incorporate detailed simulations of detector responses and physics backgrounds. Extracted parameters may be highly sensitive to the underlying theoretical models used in the MC generation. Because new physics (NP) can alter decay distributions and acceptances, the standard practice of fitting NP Wilson coefficients to SM-based measurements of the $$R(D^{(*)})$$ R ( D ( ∗ ) ) ratios can be biased. The newly developed software tool enables efficient reweighting of MC samples to arbitrary NP scenarios or to any hadronic matrix elements. We demonstrate how allows avoidance of biases through self-consistent fits directly to the NP Wilson coefficients. We also present example analyses that demonstrate the sizeable biases that can otherwise occur from naive NP interpretations of SM-based measurements. The library is presently interfaced with several existing experimental analysis frameworks and we provide an overview of its structure.