Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “geologic model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Modeling Geologic Waste Repository Systems Below Residual Saturation

The heat generated by high-level radioactive waste can pose numerical and physical challenges to subsurface flow and transport simulators if the liquid water content in a region near the waste package approaches residual saturation due to evaporation. Here, residual saturation is the fraction of the pore space occupied by liquid water when the hydraulic connectivity through a porous medium is lost, preventing the flow of liquid water. While conventional capillary pressure models represent residual saturation using asymptotically large values of capillary pressure, here, residual saturation is effectively modeled as a tortuosity effect alone. Treating the residual fluid as primarily dead-end pores and adsorbed films, relative permeability is independent of capillary pressure below residual saturation. To test this approach, PFLOTRAN is then used to simulate thermal-hydrological conditions resulting from direct disposal of a dual-purpose canister in unsaturated alluvium using both conventional asymptotic and revised, smooth models. Importantly, while the two models have comparable results over 100 000 years, the number of flow steps required is reduced by approximately 94%.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Illinois State Geological Survey (ISGS), Illinois Basin - Decatur Project (IBDP) Geological Models, July 7, 2021. Midwest Geological Sequestration Consortium (MGSC) Phase III Data Sets. DOE Cooperative Agreement No. DE-FC26-05NT42588.

Three geological models in Petrel (Mark of Schlumberger) and data output from shallow groundwater modeling using TOUGH Codes from Lawrence Berkeley National Laboratory, included under folders: Static_Geologic_Model, Dynamic_Reservoir_Model, Geomechanical_Model, and Groundwater_Model.

3D Geological Model↗
DOE OSTI2018

Fallon FORGE: 3D Geologic Model

The 3D geologic model for the Fallon for site was constructed in EarthVision software using methods similar to (Moeck et al., 2009, 2010; Faulds et al., 2010b; Jolie et al., 2012, 2015; Hinz et al., 2013a; Siler and Faulds, 2013; Siler et al., 2016a, b) - References are included in archive. The model contains 48 faults (numbered 1-48), and 4 stratigraphic surfaces from oldest to youngest (1) undivided Mesozoic basement, consisting of Mesozoic metasedimentary, metavolcanic, and plutonic units (Mzu); (2) Miocene volcanic and interbedded sedimentary rocks, consisting primarily of basaltic and basaltic andesite lava flows (Tvs); and (3) late Miocene to Pliocene (i.e., Neogene) undivided sedimentary rocks (Ns); and (4) Quaternary sediments (Qs). The two files contain points that describe nodes along the fault surfaces and stratigraphic horizons.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

RGM: Random Geological Model Generation Package

This Fortran code is to accompany a manuscript to be submitted to Computers & Geosciences, a high-impact, peer-reviewed journal in computer methods for geosciences research. This Fortran code focuses on generation of synthetic geological models using a multi-randomization strategy. Generating high-fidelity synthetic geological models, including realistic seismic reflector migration images, faults, salt bodies, and relative geological time images, is the key for many supervised machine learning methods that aim to delineate faults and other geological properties of interest from seismic migration images. Our package contains two major functionalities: generating 2D synthetic random geological models and generating 3D synthetic random geological models. In each step of the generation process, we set random values for key properties of a geological model to improve the fidelity of the resulting geological model. The package also includes example codes on how to use the random geological model generation subroutines. We name this package RGM – Random Geological Model generation package.

Gao, Kai↗
DOE OSTI2024

Stochastic representation and conditioning of process-based geological model by deep generative and recognition networks

Accurate and realistic geological modeling is the core of oil and gas development and production. In recent years, process-based methods are developed to produce highly realistic geological models by simulating the physical processes that reproduce the sedimentary events and develop the geometry. However, the complex dynamic processes are extremely expensive to simulate, making process-based models difficult to be conditioned to field data. In this work, we propose a comprehensive generative adversarial network framework as a machine-learning-assisted approach for mimicking the outputs of process-based geological models with fast generation. The main objective of our work is to obtain a continuous parametrization of the highly realistic process-based geological models which enables us to calibrate the models and condition the models to data. Numerical results are presented to illustrate the capability of our proposed methodology.

58 GEOSCIENCES↗
DOE OSTI2026

Generation of random geological models using multi-randomization for machine learning

Generating high-fidelity geological models is essential for advancing machine learning (ML) methods in automated seismic interpretation. For instance, seismic images paired with corresponding fault labels are foundational for ML-based fault detection from seismic migration sections. While several open-access datasets of random geological models exist, open-source tools specifically designed to produce large volumes of such models for ML applications remain scarce. To address this gap, we present RGM (Random Geological Model), an open-source software package for efficiently generating 2D and 3D synthetic geological models tailored for ML workflows. RGM supports the creation of diverse model components, including medium property distributions (P-/S-wave velocities and density), seismic reflectivity images (i.e., synthetic migration sections), relative geological time, and discrete fault attributes such as probability, dip, strike, rake, and displacement. It also accommodates the creation of complex geological features such as salt bodies and unconformities. The model generation algorithm employs a multi-randomization strategy, yielding an effectively infinite-dimensional model space that encompasses a wide range of geological scenarios and associated seismic features. Furthermore, RGM incorporates a method to generate synthetic elastic migration images using analytical elastic reflection coefficients combined with frequency-dependent scaling. This functionality enables the creation of training datasets for ML models that leverage elastic seismic images. RGM is implemented in modern object-oriented Fortran, allowing users to flexibly control statistical parameters governing model variability. We demonstrate the capability, performance, and geological realism of the package through comprehensive 2D and 3D examples.

58 GEOSCIENCES↗
DOE OSTI2020

Kimberlina - Regional Static 3D Geologic Model of the Southern San Joaquin Basin

Regional static 3D geologic model of the southern San Joaquin Basin for the Westcarb Kimberlina demonstration project created in Earthvision (DGI, Inc.). Also contains a smaller-scale model from the larger basin domain for the geometry used in Birkholzer et al. (2011). Data sets derived from: Wagoner, J., 2009, 3D geologic modeling of the Southern San Joaquin Basin for the Westcarb Kimberlina demonstration project—A status report: Lawrence Livermore National Laboratory LLNL-TR-410813, 27 p. Birkholzer, J.T., Zhou, Q., Cortis, A. and Finsterle, S., 2011, A sensitivity study on regional pressure buildup from large-scale CO2 storage projects. Energy Procedia, 4, pp.4371-4378. LLNL contact and file inventory creator: Kayyum Mansoor (mansoor1@llnl.gov)

3D Geological Model↗
DOE OSTI2022

Applying 3D Geologic Modeling Workflows to the Argillite Reference Case (Rev. 1)

The objective of this short report is to document the application of our 3D geologic modeling workflow to an argillite (shale) host rock. Over the past four years, our team at Los Alamos National Laboratory has developed a geologic modeling workflow that can be applied to generic alluvial basins such as those found in the western United States. In “frontier” or “exploratory” basins where data are sparse, the first steps are to collect, evaluate and integrate available subsurface data into conceptual geologic models. Those models form the basis for constructing the geologic framework model, a 3D geocellular model ideally constrained by seismic and borehole data. To date we have constructed our models using “synthetic” well data derived from conceptual models, without the prospect of validating our workflow using “real” subsurface data. We were tasked to investigate whether our workflow designed for alluvial basin sediments could be applied to other potential repository host rocks. This task also provided the opportunity to work with high-quality subsurface data collected specifically for siting and evaluating a nuclear waste repository. Nagra, the Swiss governmental agency responsible for the disposal of the nation’s radioactive waste, generously provided us with data from two deep boreholes drilled through their argillaceous target formation. The aim of our proof-of-concept demonstration is to evaluate whether geostatistical methods offer a viable approach to property modeling in argillaceous rocks. Nagra provided us with the well data on the condition that we maintain confidentiality with all transferred information and results. Fortunately, Nagra posts numerous technical reports on its public website that describe the subsurface geology in great detail. All of the information and illustrations in this report related to the Swiss repository enterprise are taken from the Nagra public website.

58 GEOSCIENCES↗
DOE OSTI2014

Geologic Modeling and Simulation Report for the Aquistore Project

The Plains CO 2 Reduction (PCOR) Partnership, through the Energy & Environmental Research Center (EERC), has been supporting, and continues to support, the Petroleum Technology Research Centre (PTRC) Aquistore project. This support has been in the form of geologic characterization, involvement in the Science and Engineering Research Committee (SERC), involvement in public outreach, developing geologic models and running predictive simulations on the expected injection program at the site. The Aquistore project is part of the world’s first commercial postcombustion carbon capture, utilization, and storage project from a coal-fired power-generating facility, the SaskPower Boundary Dam, located in Saskatchewan, Canada, and will be acting as a storage site for a portion of the captured CO 2 from the Boundary Dam power plant. The Aquistore site includes one injection well and a 152-meter offset observation well. Both wells were drilled and completed in the Deadwood and Black Island Formations. At the time of this report, injection at the Aquistore site is anticipated to begin in late 2014. To better understand the storage implications of injecting carbon dioxide (CO 2 ) at the Aquistore site, the EERC has constructed P10, P50, and P90 geologic model realizations and run three new predictive simulation scenarios on each realization. These models and simulations were constructed to better understand both operational and geologic uncertainties that may exist at the Aquistore site. The geologic model realizations and simulations are an update to those completed in the original report entitled “Geologic Modeling and Simulation Report for the Aquistore Project,” Deliverable D93, approved in March 2014. In this update, the same fine-scale model extent of the 34-square-kilometer PTRC 3-D seismic survey area, with higher structural resolution, was continually used for the uncertainty analysis. A low (P10), mid (P50), and high volumetric (P90) case for the amount of pore volume accessible to store the potential injected CO 2 was ranked based on certain deviation variations of model-building parameters, including effective porosity and net-to-gross reservoir, in six sand units of the study area. Three cases with various injection rate and period schemes were simulated based on uncertainty models P10, P50, and P90.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Evolution of a Geological Model for Co-Producing Electricity at the Blackburn Oil Field, Nevada: Preprint

Oil fields characterized by significant proportions of hot water in the reservoir offer a unique opportunity for geothermal energy co-production and utilization. Development of an accurate geological model is essential in understanding the subsurface. However, this is a challenge at the preliminary stages of resource assessment when data on the subsurface parameters and subterranean fault network is scarce. Our focus in this paper is to explore a methodology for developing an accurate conceptual geological model of the complexly faulted reservoir at the Blackburn Field, Nevada, to create a numerical simulation that will eventually be used to assess the potential of co-producing electricity. There are four steps to the evolution of this model: (1) collection of public data and research on the geological setting of the system; (2) digitization of seismic time-interpretation and cross-sections to create the most representative model of the subsurface; and (3) creation of a natural-state numerical model to simulate the thermal gradient through the subsurface. Utilizing publicly available data of the geological system and Leapfrog conceptual modeling software, we refined a preliminary model to be more representative of the subsurface geology of an active geothermal exploration stage project. The conceptual geological model developed has been imported into VOLSUNG reservoir modeling software to create a natural-state model, further characterizing the Blackburn Field reservoir's thermal gradient. In the future, new seismic data will be utilized to further evolve the conceptual geological model for numerical simulations.

Basin and Range province↗
DOE OSTI2021

Interferometric SAR modelling of near surface data to improve geological model in the Surat Basin, Australia

Here we present a study on geophysical inverse modelling for subsurface structural properties of an unconventional hydrocarbon site that was monitored previously by Interferometric Synthetic Aperture Radar (InSAR) technology for surface deformation. A static three-dimensional geomodel along with extracted property maps replicates the depth of each underlying stratigraphic unit and structural feature with the density of each geological layer. We examine the hypothesis that integration of elastic properties of each formation layer with InSAR observations in a stratified elastic medium will lead to a viscoelastic geophysical inverse problem that can be solved to estimate fractional volume change at the reservoir level. Moreover, we examine synthetic scenarios in which the elastic properties of the formations are perturbed before determining the resulting impact on the rate of surface deformation. The results show that although the slope of underlying formations, their density and depth can define the extent and pattern of a deformation signal, their properties have a marginal impact on volumetric change compared to the dense network of shallow depth Coal Seam Gas (CSG) mining wells. Besides, it is also demonstrated that the inversion of InSAR deformation maps can resolve the uncertainties associated with low-resolution seismic interpretation as well as filling the data gaps within seismic acquisitions. A significant contribution of this investigation to the geological basin modelling involves a) introducing a remote and non-invasive technology such as InSAR to improve geophysical mapping of subsurface structures such as faults in areas with sparse or no reflective seismic information, and b) applying a multi-layer viscoelastic geophysical source model for an unconventional hydrocarbon reservoir such as CSG.

58 GEOSCIENCES↗
DOE OSTI2016

Fallon FORGE 3D Geologic Model

An x,y,z scattered data file for the 3D geologic model of the Fallon FORGE site. Model created in Earthvision by Dynamic Graphic Inc. The model was constructed with a grid spacing of 100 m. Geologic surfaces were extrapolated from the input data using a minimum tension gridding algorithm. The data file is tabular data in a text file, with lithology data associated with X,Y,Z grid points. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

3-D Geological Modeling for Numerical Flow Simulation Studies of Gas Hydrate Reservoirs at the Kuparuk State 7-11-12 Pad in the Prudhoe Bay Unit on the Alaska North Slope

Accurate reservoir evaluation requires reliable three-dimensional (3-D) geological models. Here, this study conducted 3-D geological modeling for numerical flow simulation of the B1 sand gas hydrate reservoir at the Kuparuk State 7-11-12 pad, Prudhoe Bay Unit, Alaska North Slope. The model integrates well logs, core, and seismic data to address spatial heterogeneity in geological structures and reservoir properties. Two modeling types were performed: structural framework modeling and petrophysical property modeling. For structural framework modeling, seismic data and well log markers were used to reproduce subsurface structures characterized by a normal fault system. A volume-based modeling algorithm and stair-stepping grid were applied. The resulting 3-D model comprised 2,640,000 grid cells across 264 layers, including seven fault grids. For petrophysical property modeling, total porosity was initially modeled using sequential Gaussian simulation with collocated cokriging. To reproduce the upward coarsening of the B1 sand, upscaled log-derived total porosity and a three-dimensional (3-D) trend depicting total porosity variation were used as primary and secondary data, respectively. Gas hydrate saturation distribution was modeled similarly, with secondary data from estimated porosity distribution and seismic-derived acoustic impedance map enhancing accuracy. Results indicate higher gas hydrate saturation in the upper part of the B1 sand and areas with higher acoustic impedance. Intrinsic permeability was modeled from the total porosity and clay-bound water volume, and effective permeability was derived from the gas hydrate saturation and intrinsic permeability distributions based on the “Tokyo model”. Effective permeability distributions were influenced by the total porosity, gas hydrate saturation, and intrinsic permeability. Within the same layer, higher gas hydrate saturation leads to decreased effective permeability. In total, 100 sets of multiple scenarios were prepared, providing input data for dynamic flow simulations to evaluate the effects of lateral heterogeneity in reservoir properties and the hydraulic characteristics of faults on production behavior for preassessment before the long-term production test.

58 GEOSCIENCES↗
DOE OSTI2016

West Flank Coso FORGE: 3D Geologic Model

This is an x,y,z file of the West Flank FORGE 3D geologic model. Model created in Earthvision by Dynamic Graphic Inc. The model was constructed with a grid spacing of 100 m. Geologic surfaces were extrapolated from the input data using a minimum tension gridding algorithm. The data file is tabular data in a text file, with lithology data associated with X,Y,Z grid points. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

15 GEOTHERMAL ENERGY↗
DOE OSTI2014

Geologic Modeling and Simulation Report for the Aquistore Project

The Plains CO 2 Reduction (PCOR) Partnership, through the Energy & Environmental Research Center (EERC), is collaborating with the Petroleum Technology Research Centre (PTRC) on site characterization; modeling and simulation; risk assessment; public outreach; and monitoring, verification, and accounting (MVA) activities for the Aquistore project. The Aquistore project is a carbon capture, utilization, and storage (CCUS) project situated near the town of Estevan, Saskatchewan, Canada, and the U.S.–Canada border. This project is managed by PTRC and will serve as buffer storage of carbon dioxide (CO 2 ) from the SaskPower Boundary Dam CCUS project, the world’s first commercial-scale postcombustion CCUS project from a coal-fired electric generating facility. To date, an injection well and an observation research well (~500 ft apart) have been drilled and completed at the Aquistore site, with injection anticipated to begin in 2014. Using a combination of site characterization data provided by PTRC and independently acquired information, the PCOR Partnership has constructed a static geologic model to assess the potential storage capacity of the Aquistore site and provide the foundation for dynamic simulation. The geologic model and the results of the predictive simulations will be used in the risk assessment process to help define an overall monitoring plan for the project and to assure stakeholders that the injected CO 2 will remain safely stored at the Aquistore site.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2013

3-Dimensional Geologic Modeling Applied to the Structural Characterization of Geothermal Systems: Astor Pass, Nevada, USA

Geothermal systems in the Great Basin, USA, are controlled by a variety of fault intersection and fault interaction areas. Understanding the specific geometry of the structures most conducive to broad-scale geothermal circulation is crucial to both the mitigation of the costs of geothermal exploration (especially drilling) and to the identification of geothermal systems that have no surface expression (blind systems). 3-dimensional geologic modeling is a tool that can elucidate the specific stratigraphic intervals and structural geometries that host geothermal reservoirs. Astor Pass, NV USA lies just beyond the northern extent of the dextral Pyramid Lake fault zone near the boundary between two distinct structural domains, the Walker Lane and the Basin and Range, and exhibits characteristics of each setting. Both northwest-striking, left-stepping dextral faults of the Walker Lane and kinematically linked northerly striking normal faults associated with the Basin and Range are present. Previous studies at Astor Pass identified a blind geothermal system controlled by the intersection of west-northwest and north-northwest striking dextral-normal faults. Wells drilled into the southwestern quadrant of the fault intersection yielded 94°C fluids, with geothermometers suggesting a maximum reservoir temperature of 130°C. A 3-dimensional model was constructed based on detailed geologic maps and cross-sections, 2-dimensional seismic data, and petrologic analysis of the cuttings from three wells in order to further constrain the structural setting. The model reveals the specific geometry of the fault interaction area at a level of detail beyond what geologic maps and cross-sections can provide.

15 GEOTHERMAL ENERGY↗