Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel assembly”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Nuclear fuel assemblies and fuel debris monitor for characterization of fuel assemblies for final storage

NUKEM monitor FAMOS is designed to measure the burn up of fuel assemblies (FA's) and allows the calculation of the content of fissile material and other actinides. The knowledge of the isotopic composition and activities of FA's is required for a safe handling and storage of the elements. The monitor analyses the measurement results on the basis of burn up calculations which improve the quality of the results, with respect to previous systems, which did not use those. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Nuclear imaging of the fuel assembly in ignition experiments

First results from the analysis of neutron image data collected on implosions of cryogenically layered deuterium-tritium capsules during the 2011-2012 National Ignition Campaign are reported. The data span a variety of experimental designs aimed at increasing the stagnation pressure of the central hotspot and areal density of the surrounding fuel assembly. Images of neutrons produced by deuterium–tritium fusion reactions in the hotspot are presented, as well as images of neutrons that scatter in the surrounding dense fuel assembly. The image data are compared with 1D and 2D model predictions, and consistency checked using other diagnostic data. The results indicate that the size of the fusing hotspot is consistent with the model predictions, as well as other imaging data, while the overall size of the fuel assembly, inferred from the scattered neutron images, is systematically smaller than models' prediction. Preliminary studies indicate these differences are consistent with a significant fraction (20%–25%) of the initial deuterium-tritium fuel mass outside the compact fuel assembly, due either to low mode mass asymmetry or high mode 3D mix effects at the ablator-ice interface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Decay Heat Calculations for PWR and BWR Assemblies Fueled with Uranium and Plutonium Mixed Oxide Fuel using SCALE

In currently operating commercial nuclear power plants (NPP), there are two main types of nuclear fuel, low enriched uranium (LEU) fuel, and mixed-oxide uranium-plutonium (MOX) fuel. The LEU fuel is made of pure uranium dioxide (UO{sub 2} or UOX) and has been the fuel of choice in commercial light water reactors (LWRs) for a number of years. Naturally occurring uranium contains a mixture of different uranium isotopes, primarily, {sup 235}U and {sup 238}U. {sup 235}U is a fissile isotope, and will readily undergo a fission reaction upon interaction with a thermal neutron. {sup 235}U has an isotopic concentration of 0.71% in naturally occurring uranium. For most reactors to maintain a fission chain reaction, the natural isotopic concentration of {sup 235}U must be increased (enriched) to a level greater than 0.71%. Modern nuclear reactor fuel assemblies contain a number of fuel pins potentially having different {sup 235}U enrichments varying from {approx}2.0% to {approx}5% enriched in {sup 235}U. Currently in the United States (US), all commercial nuclear power plants use UO{sub 2} fuel. In the rest of the world, UO{sub 2} fuel is still commonly used, but MOX fuel is also used in a number of reactors. MOX fuel contains a mixture of both UO{sub 2} and PuO{sub 2}. Because the plutonium provides the fissile content of the fuel, the uranium used in MOX is either natural or depleted uranium. PuO{sub 2} is added to effectively replace the fissile content of {sup 235}U so that the level of fissile content is sufficiently high to maintain the chain reaction in an LWR. Both reactor-grade and weapons-grade plutonium contains a number of fissile and non-fissile plutonium isotopes, with the fraction of fissile and non-fissile plutonium isotopes being dependent on the source of the plutonium. While only RG plutonium is currently used in MOX, there is the possibility that WG plutonium from dismantled weapons will be used to make MOX for use in US reactors. Reactor-grade plutonium in MOX fuel is generally obtained from reprocessed irradiated nuclear fuel, whereas weapons-grade plutonium is obtained from decommissioned nuclear weapons material and thus has a different plutonium (and other actinides) concentration. Using MOX fuel instead of UOX fuel has potential impacts on the neutronic performance of the nuclear fuel and the design of the nuclear fuel must take these differences into account. Each of the plutonium sources (RG and WG) has different implications on the neutronic behavior of the fuel because each contains a different blend of plutonium nuclides. The amount of heat and the number of neutrons produced from fission of plutonium nuclides is different from fission of {sup 235}U. These differences in UOX and MOX do not end at discharge of the fuel from the reactor core - the short- and long-term storage of MOX fuel may have different requirements than UOX fuel because of the different discharged fuel decay heat characteristics. The research documented in this report compares MOX and UOX fuel during storage and disposal of the fuel by comparing decay heat rates for typical pressurized water reactor (PWR) and boiling water reactor (BWR) fuel assemblies with and without weapons-grade (WG) and reactor-grade (RG) MOX fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Grid pressure drop prediction in a fuel assembly

In fuel assembly, spacer grids have strong effects on pressure drop and other thermal-hydraulic behaviors. Considering the design and safety operation of a reactor, it is important to predict pressure drop accurately in the fuel assembly. For a mixed core, a reactor with mixed fuel designs in the reactor core, undesired cross flow were often caused by differences in pressure drop among neighboring bundles. The pressure drop is often estimated for designs of new reactor core fuel assemblies. In the past, due to complex flow conditions in fuel assembly, the pressure drop of a fuel assembly relied greatly on costly and time-consuming full length thermal hydraulic tests. Some empirical pressure drop correlations and CFD methodology were applied, however, only limited to a single gird span. Without considering pressure drop in the entire fuel assembly it is quite difficult to optimize the fuel assembly design. Most experimental fuel assemblies consist of mixing vane grids (MVG) and simple support grids (SSG). The MVG's were the main tested spacer grids in the reactor and SSG's were used only in experimental study to support the fuel assembly. In fuel reactor core, the fuel assembly heats the coolant, which could turn the single-phase water system into a two-phase flow system and eventually lead to critical heat flux (CHF). Because of the complexity of phase change, it is very difficult to predict pressure drop in rod bundles with two-phase flow. In this paper, a new method to predict the pressure drop in the fuel assembly is proposed and verified by experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Partial defect verification of spent fuel assemblies by PDET: Principle and field testing in Interim Spent fuel Storage Facility (CLAB) in Sweden

Here, the need for the development of a credible method and instrument for partial defect verification of spent fuel has been emphasized over a few decades in the safeguards communities as the diverted spent fuel pins can be the source of nuclear terrorism or devices. The need is increasingly more important and even urgent as many countries have started to transfer spent fuel to so called "difficult-to-access" areas such as dry storage casks, reprocessing or geological repositories. Partial defect verification is required by IAEA before spent fuel is placed into "difficult-to-access" areas. Earlier, Lawrence Livermore National Laboratory (LLNL) has reported the successful development of a new, credible partial defect verification method for pressurized water reactor (PWR) spent fuel assemblies without use of operator data, and further reported the validation experiments using commercial spent fuel assemblies with some missing fuel pins. The method was found to be robust as the method is relatively invariant to the characteristic variations of spent fuel assemblies such as initial fuel enrichment, cooling time, and burn-up. Since then, the PDET system has been designed and prototyped for 17×17 PWR spent fuel assemblies, complete with data acquisition software and acquisition electronics. In this paper, a summary description of the PDET development followed by results of the first successful field testing using the integrated PDET system and actual spent fuel assemblies performed in a commercial spent fuel storage site, known as Central Interim Spent fuel Storage Facility (CLAB) in Sweden will be presented. In addition to partial defect detection initial studies have determined that the tool can be used to verify the operator declared average burnup of the assembly as well as intra-assembly bunrup levels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Solutions for management of defective fuel assemblies - 15318

Defective fuel management is a major challenge for nuclear operators when the time comes for finding a long-term solution for their used (or spent) fuel assemblies. This question of defective fuel management can be raised in several cases: - For optimizing the remaining operating costs of shutdown reactors, the spent fuel pools must be emptied as soon as possible; a solution needs therefore to be found for evacuating all the spent fuel assemblies, defective fuel assemblies and in particular defective fuel rods included; - Some utilities are today facing a saturation of their reactor spent fuel pool; evacuating the defective fuel assemblies and extracted defective fuel rods allows optimizing the space in the pool. Whereas the solutions for managing intact used fuel assemblies are well-known, a specific technical solution must be implemented for managing the defective spent fuel assemblies as well. The purpose of this paper is to describe the existing solutions for the management of all types of defective fuel assemblies. Interim Dry Storage Solution Interim dry storage of defective spent fuel assemblies is being implemented for decades in the USA. Specific operations are performed for preparing the defective fuel assemblies for interim dry storage and they are then stored with intact used fuel assemblies in the dry storage cask. The advantage of such a solution is its short-term cost effectiveness. The paper presents the existing dry interim storage solutions for defective used fuel rods, the way they are implemented, the associated operational experience. Long-term Dry Storage Solution A long-term dry storage solution for defective fuel assemblies is being developed, compliant with direct disposal requirements. The solution is based on the encapsulation of each defective fuel rod into a fuel rod capsule and an associated specific dry storage licensing approach: this is the best available technology regarding long term storage safety requirements. The paper presents this unique capsule technology, the transport and storage casks that can be used for transportation of defective fuel rods to the storage facility, and the associated transport licensing approach currently used in Europe. Treatment Solution. The most definitive way to get rid of defective fuel assemblies is their treatment (or reprocessing) in a treatment plant. There is then no need to assess the behaviour of these specific used fuel assemblies as for an interim storage facility or a final repository. The advantage of such a solution is its sustainable approach. The paper presents the existing transport and treatment solutions, the way they are implemented, the associated operational experience. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

New Approach to Eccentric Positioning of Fuel Assemblies in a Spent Fuel Pool

Criticality analyses of a spent fuel pool (SFP) typically assume the fuel assemblies are centered in the cells. In reality fuel assemblies are not constrained to be centered but can be placed anywhere within the available space. For SFPs with absorber panels it has been shown that the most reactive condition is with the fuel assemblies centered. However, for SFPs without absorber panels eccentric positioning of assemblies increases reactivity. Historically, it was common practice to analyze eccentric positioning by modeling a 2x2 arrangement of the fuel where each assembly is positioned toward the center (with reflective or periodic bounding conditions). The delta k between the eccentric model and the center model was taken as an uncertainty which was then statistically combined with other uncertainties. This historical approach had two problems. First, arrangement of more than 4 assemblies placed toward the center of the model produced higher k's. Second, in a large pool it was likely that 4 assemblies collocated toward each other would exist so asymmetry should be treated as a bias rather than an uncertainty. The number of collocated assemblies is important to the magnitude of the effect. Since spent fuel pools are large it is expected that some collocated eccentrically placed assemblies will occur so the eccentric placement reactivity should be accounted for by a bias. The magnitude of this bias depends greatly on the number of eccentrically placed assemblies that are collocated. A simple probability model assuming random placement can be used to establish the number of collated eccentric assemblies. It has been shown that for a SFP with 800 cells there is less than a 5% probability that more than 16 eccentric assemblies will be collocated. The eccentricity bias using 16 eccentric assemblies collocated is small (on the order of 0.001 in delta k or less) and should be easy to add as a bias in the SFP criticality analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

R-Functions Method in the Mathematical Modeling of Convective Heat Exchange in an Octahedral Fuel Assembly with 37 Fuel Elements

We consider conjugate boundary-value problems of heat exchange for the cases where a viscous incompressible liquid moves through channels with noncanonical cross section flowing around a bundle of rods. The influence of the type of packing on the velocity and temperature distributions is investigated. For the solution, we use the R-functions method in combination with the Ritz variational method. We consider the cases of cyclic, staggered, and rectangular packing of fuel elements.

97 MATHEMATICS AND COMPUTING↗

Investigation of Scintillator Based Partial Defect Detector for Safeguarding Spent Fuel Assemblies

Safeguarding spent fuel assemblies is one of the most important objectives for nuclear non-proliferation, since it contains fissile material which can be diverted into nuclear explosive devices. Partial defect detection is a challenging issue among IAEA future safeguards requirements. The IAEA defines there exist partial defects if 50% or more of the fuel pins in a spent fuel assembly are diverted. Conventional partial defect detectors are classified into two groups depending on its operating principle. The first group applies gamma/neutron spectrometer, which are PDET, SMOPY, and gamma emission tomography. Partial defect detectors in the first group are able to calculate the burnup, isotope composition, and cooling time of a spent fuel assembly. However, since it takes time to analyze a spent fuel assembly, they cannot detect every spent fuel assemblies in a cooling pool. The second group applies Cerenkov radiation detector, which can screen a spent fuel assembly within a short time. However, since Cerenkov radiation cannot be generated under atmospheric environment, it cannot be applied for dry condition. This research proposes a scintillator based partial defect detector (SPDD) for inspecting spent fuel, which can detect partial defects within a short time and both in and out of a cooling pool.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Development and evaluation of a list mode neutron coincidence collar for spatial response measurements of fresh fuel assemblies

A traditional safeguards neutron coincidence counting system, the Neutron Coincidence Collar, has been modified to incorporate individual preamplifiers on each of its 18 3He tubes in active interrogation mode. When used with list mode data acquisition (LMDA) and analysis, a signal from each 3He tube can be recorded and analyzed to allow a spatial response measurement to be performed on an item based on count rate and 3He tube location within the system. The ultimate goal of this project is to demonstrate the capabilities of a list mode response matrix for the nondestructive assay of fresh nuclear fuel assemblies. To enable partial defect detection of fuel pin locations and absences within an assembly, the project aims to extend well-established correlated neutron analysis techniques on a preexisting Neutron Coincidence Collar by extracting a greater number of useful signatures from the system than are currently generated. LMDA, combined with the addition of multiple preamplifiers, facilitates this capability by increasing the number of simultaneous signals that can be measured; this allows an in-depth analysis of neutron coincidence events to determine a fissioning item’s location based on the measured doubles count rate in various channel logic coincidence combinations. All of this can be done from a single measurement pulse train in offline analysis, which is the major benefit provided by LMDA. Through various stages of development and testing, a Mirion Technologies model JCC-71 Neutron Coincidence Collar has been successfully retrofit with modern electronics designed in-house at Oak Ridge National Laboratory, matching preexisting JAB-01 electronics performance, while maintaining the original system footprint. This paper presents these various stages of development and experimental evaluation of the proof of concept system.

Moore, Angela S.↗

Comparisons of Peak Cladding Temperature and Effective Thermal Conductivity: CFD Simulation on PWR Spent Fuel Assemblies - 16278

When spent fuel assemblies from the reactor of nuclear power plants (NPPs) are transported or stored, the assemblies are exposed to a variety of environments that can affect the peak cladding temperature of spent fuel assemblies. There are four methods to calculate the peak cladding temperature of spent fuel assemblies in a cask: Manteufel and Todreas's two-region model, Bahney Lotz's effective thermal conductivity model, Wooton-Epstein correlation, and computational fluid dynamics (CFD) simulation. The CFD simulation based on the FLUENT code is used to calculate the peak cladding temperature and effective thermal conductivity of a spent fuel assemblies used in Republic of Korea NPPs: 14x14, 16x16 ACE7, 16x16 PLUS7 and 17x17 PWR spent fuel assemblies. The CFD simulation results show that the effective thermal conductivity of the 16x16 ACE7 was more conservative than those for the other assemblies. Therefore the effective thermal conductivity using 16x16 ACE7 is used for thermal evaluation of the KORAD's developing cask which can load 14x14, 16x16 ACE7, 16x16 PLUS7 and 17x17 spent fuel assembly. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Emergency response and solutions for damaged fuel assembly handling events - Lessons learned from a 2013 fuel positioning issue

In 2013, during the refueling of a French 1300 MWe reactor, a fuel assembly (FX3599) was damaged by a fuel assembly positioning tool in the reactor vessel. The upper part of a corner rod of the fuel assembly was twisted and the top end grid was torn off. Because of the protruding fuel rod, the assembly could not be easily transferred for repair to the fuel storage pool via the transfer tube. This unexpected and rarely encountered situation was assessed jointly by EDF and AREVA NP. The chosen option was to directly perform the field service inside the reactor building in cells generally used for intermediate storage during refueling. This operation, performed by EDF and AREVA, involved removing the twisted rod and positioning it in a special-purpose canister by means of a gripper-type tool for removal (KIPCI gripper) and a gripper for holding the rod in place. The special-purpose canister was designed, ordered and supplied by a sub-supplier within one week. The operation went through 3 phases. First a preparation step in the fuel building: The stripper was disassembled and technical checks carried out to ensure correct operation. The gripper tightening force was checked in real-life conditions with the gripper suspended from auxiliary crane. The fuel rod removal was simulated several times by trained operators. Second, the equipment was installed in the reactor building. And third, the operation took place in the reactor cavity: the special-purpose canister was opened, the radioactive waste canister placed in the special-purpose canister, the twisted fuel rod was then grasped by the KIPCI gripper and removed from the fuel assembly. The twisted fuel rod was positioned above the canister and dropped into it. Once the fuel rod had been removed, the canister and fuel assembly FX3599 were transferred to the fuel building and refueling resumed. The canister containing the fuel rod is currently in interim storage in the reactor pool until appropriate action is taken for it to be shipped and eventually reprocessed. EDF has performed improvement in its handling procedures and in its handling tools to avoid a similar new event.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

LWR fuel assembly designs for the transmutation of LWR Spent Fuel TRU with FCM and UO{sub 2}-ThO{sub 2} Fuels

In this paper, transmutation of transuranic (TRU) nuclides from LWR spent fuels is studied by using LWR fuel assemblies which consist of UO{sub 2}-ThO{sub 2} fuel pins and FCM (Fully Ceramic Microencapsulated) fuel pins. TRU from LWR spent fuel is loaded in the kernels of the TRISO particle fuels of FCM fuel pins. In the FCM fuel pins, the TRISO particle fuels are distributed in SiC matrix having high thermal conductivity. The loading patterns of fuel pins and the fuel compositions are searched to have high transmutation rate and feasible neutronic parameters including pin power peaking, temperature reactivity coefficients, and cycle length. All studies are done only in fuel assembly calculation level. The results show that our fuel assembly designs have good transmutation performances without multi-recycling and without degradation of the safety-related neutronic parameters. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Simulation methodology for fuel assembly drop accident during handling

Fresh and irradiated fuel assembly handling is a routine part of Nuclear Power Plant activities. Fuel Assembly handling occurs during fresh fuel receipt, core refueling, spent fuel assemblies transfer from spent fuel pool to the storage containers, etc. Westinghouse, ENUSA and KEPCO-NF have collaborated in the technical area of Fuel Assembly Drop Accident (FADA) Simulation to update the approach for estimating the number of failed fuel rods as a consequence of a fresh or irradiated fuel assembly drop, which might occur during a handling accident in a PWR-type reactor. The proposed FADA simulation methodology starts with an assessment of fuel assembly impact velocity at the final stage of the drop in water or air. The vertical, horizontal or inclined drop directions are considered. This velocity is an input to determine a fuel assembly structural response during impact which defines the loading function for the fuel assembly components including spacer grids. The dynamic load on the fuel rod is calculated from the detailed spacer grid model and the corresponding loading function. Finally, the load from the spacer grid spring and dimples are applied to the fuel rod model to determine the cladding parameters for use in compliance to fuel rod cladding failure criteria. A combination of first principal, finite element analysis (FEA) and computational fluid dynamic (CFD) methods has been utilized to create a technically sound methodology. A number of specific and traditional tests for the fuel assembly and its components has been used to confirm that the proposed approaches which describe the physical phenomena related to the fuel assembly drop accident are reasonably conservative.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗