Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Transmission electron microscopy characterization of the fuel-cladding chemical interactions in HT9 cladded U-10Zr fuel

Fuel cladding chemical interaction (FCCI) is a key phenomenon needs to be better understood to establish the design basis for U-10Zr metallic fuel performance. Characterizing the microstructure and chemical composition of FCCI at micron and sub-micron scale is critically important toward a more mechanistic understanding of FCCI phenomenon and its potential effects on cladding integrity and metallic fuel performance. This paper, by using transmission electron microscopy, investigated the FCCI region in HT9 cladded U-10Zr fuel irradiated to 5.7% FIMA burnup at a peak inner cladding temperature of 615 °C in Fast Flux Test Facility (FFTF). Four distinct layers are identified in the FCCI region. The migration of Fe into the fuel side leads to the formation of several U-Zr-Fe ternary phases, including ?-Fe0.5Zr0.32U0.18, e-Fe0.3Zr0.4U0.3, and ?-Fe0.06Zr0.23U0.71, mingled with UFe2, U6Fe, and U phase at various Fe penetration depth up to ~ 150 µm. On the cladding side, grain coarsening and significant lanthanides infiltration along grain boundaries are observed. Laves phase, (Fe,Cr)2(Mo,W), which typically does not exist in fresh HT9, is identified in a wide radial range in the cladding. The typical HT9 martensitic lath structure and pre-existing M23C6 precipitates disappear, partially or completely, depending on the radial distance from the fuel-cladding interface. Those microstructural and compositional changes could cause mechanical degradation in the HT9 cladding. The present characterization results will improve the understanding of FCCI phenomenon and facilitate the development of microstructure-informed FCCI modeling for metallic fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Data for Greenhouse Gas Accounting Procedures in Low Carbon Fuel Policies Overlook the Spatial Variability of Miscanthus-Derived Sustainable Aviation Fuel

Low carbon fuel policies such as the U.S. Renewable Fuel Standard (RFS), Canada Clean Fuel Regulations (CFR), and California Low Carbon Fuel Standard (LCFS) as well as the 45Z tax credit are intended to reduce greenhouse gas (GHG) emissions from transportation. Cellulosic feedstocks, optimized biorefineries, and favorable farming locations can significantly reduce biofuel carbon intensity (CI). Despite advances in field-to-fuel GHG monitoring and flexibility in resource allocation within biorefineries (e.g., governing net electricity production), rigid CI accounting procedures in current policies may limit CI responsiveness across candidate sites and processing facilities. This work examines a hypothetical biomass-to-sustainable aviation fuel (SAF) pathway using miscanthus and alcohol-to-jet (i) to demonstrate how GHG accounting requirements drive estimates of biofuel CIs and (ii) to explore potential CI and financial implications of scenario-specific life cycle assessment (LCA). Results demonstrate that GHG accounting using the CFR/LCFS can reasonably account for distinct levels of net electricity production by a biorefinery, but only the CFR yields similar CI sensitivity to spatially explicit factors (feedstock CI, grid electricity CI) as scenario-specific LCA: most GHG accounting frameworks do not capture CI variation across candidate sites in the United States. Ultimately, this work demonstrates the importance of LCA methodological specifications in low carbon fuel policies and tax credits.

Miscanthus↗
DOE OSTI2022

Production and Catalytic Upgrading of 2,3-Butanediol Fermentation Broth into Sustainable Aviation Fuel Blendstock and Fuel Properties Measurement

With the increasing demand for sustainable supplies of aviation fuel and need to address climate change, new conversion technologies are needed to efficiently process biomass, produce high quality jet fuel blendstock, and meet carbon emission targets. This study demonstrates the synthesis, conditioning, and catalytic upgrading of 2,3-butanediol (BDO) fermentation broth into a jet fuel blendstock candidate. A high-titer 2,3-BDO fermentation broth (i.e., ~90 g/L) was produced at a 100-L scale and pretreated via nanofiltration to decrease the impurities level in the broth from 4.6 to 0.6 wt%. A novel process for catalytic upgrading of aqueous 2,3-BDO into a jet fuel blendstock candidate was developed, and each step was efficiently demonstrated. The catalytic steps include 1) 2,3-BDO dehydration into methyl ethyl ketone (MEK) over AlPO4, 2) MEK conversion into olefins over Zn1Zr10Ox, 3) oligomerization of olefins over a zeolite beta, and 4) hydrogenation over platinum/carbon. Both the model feed and real 2,3-BDO fermentation broth were tested for upgrading 2,3-BDO to MEK. With the real feed, a continuous loss of conversion (i.e., >50% loss over ~140 h time-on-stream [TOS]) was partly attributed to reversible deactivation from coking species. However, the conversion remained stable with the model feed, which demonstrates the efficiency of the first step for converting aqueous 2,3-BDO (10 wt% in water). For upgrading MEK to olefins, high selectivity to olefins (i.e., 82.5%) was obtained at high conversion levels (i.e., 93-98%) with stable conditions being achieved for > 70-hours TOS. Oligomerization of light olefins, which was demonstrated for > 270 h TOS, mainly led to the formation of dimers (C8-10) and trimers (C13-14). The oligomerized product was hydrogenated and distilled to recover the jet fraction (35 mass% or 40.9% carbon based yield), which consists mostly of desired isoalkanes (31.7 wt%), n-alkanes (24.5 wt%), and cycloalkanes (29.6 wt%). While some improvement is still needed to meet ASTM D7566 specifications for viscosity and final boiling point temperature, freezing point, density, aromatics content, and sulfur content of the jet blendstock candidate were within acceptable ranges, thus highlighting the potential of this process for production of jet fuel blendstock.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
NASA NTRS1953

Fuel characteristics pertinent to the design of aircraft fuel systems, Supplement I : additional information on MIL-F-7914(AER) grade JP-5 fuel and several fuel oils

Since the release of the first NACA publication on fuel characteristics pertinent to the design of aircraft fuel systems (NACA-RM-E53A21), additional information has become available on MIL-F7914(AER) grade JP-5 fuel and several of the current grades of fuel oils. In order to make this information available to fuel-system designers as quickly as possible, the present report has been prepared as a supplement to NACA-RM-E53A21. Although JP-5 fuel is of greater interest in current fuel-system problems than the fuel oils, the available data are not as extensive. It is believed, however, that the limited data on JP-5 are sufficient to indicate the variations in stocks that the designer must consider under a given fuel specification. The methods used in the preparation and extrapolation of data presented in the tables and figures of this supplement are the same as those used in NACA-RM-E53A21.

Barnett, Henry C↗
DOE OSTI2021

Impact of low reactivity fuel type on low load combustion, emissions, and cyclic variations of diesel-ignited dual fuel combustion

In this study, cyclic variations in dual fuel combustion with diesel ignition of three different low reactivity fuels (methane, propane, and gasoline) are examined under identical operating conditions. Experiments were performed on a single cylinder research engine (SCRE) at a low load of 3.3 bar brake mean effective pressure (BMEP). The start of injection (SOI) of diesel was varied from 280 to 330 absolute crank angle degrees (CAD). Engine speed, rail pressure, and boost pressure were held constant at 1500 rpm, 500 bar, and 1.5 bar, respectively. The energy substituted by the low reactivity fuel was fixed at 80% of the total energy input. It was found that diesel-methane (DM) and diesel-propane (DP) combustion were affected by diesel mixing to a greater extent than diesel-gasoline (DG) combustion due to the higher reactivity of gasoline. The magnitude of low temperature heat release was greatest for DG combustion followed by DM and DP combustion for all SOIs. The ignition delay for DG combustion was the shortest, followed by DM and DP combustion. DM and DP combustion exhibited more cyclic variations than DG combustion. Cyclic variations decreased for DM and DP combustion when SOI was advanced; however, DG combustion cyclic variations remained essentially constant for all SOIs. Earlier SOIs (280, 290, 300, and 310 CAD) for DM and (280, 290, and 300 CAD) for DP combustion indicated some prior-cycle effects on the combustion and IMEP (i.e. some level of determinism).

Engineering↗
DOE OSTI2021

Towards cost-competitive middle distillate fuels from ethanol within a market-flexible C2 platform-based biorefinery concept

Ethanol to middle distillates (ETMD) is a promising pathway to produce sustainable liquid fuels to decarbonize the hard-to-electrify transportation sectors due to (1) the abundant sugar/starch and lignocellulosic biomass, (2) the existing deployment scale of fuel ethanol production (similar to 29 billion gallons per year globally), and (3) emerging opportunities in C2+ alcohol synthesis from CO2. Here we report a conceptual market-responsive biorefinery centered around a new ETMD pathway based on one-step ethanol to butene-rich olefins (ETO) over a Cu-Zn-Y/Beta catalyst. Specifically, this ethanol conversion pathway comprises one-step ETO, oligomerization, and hydrotreating. This ETO is distinct from that in the conventional ethanol-to-jet process which is based on two-step ethanol to ethylene and ethylene oligomerization to butenes. Butene-rich olefins can be shifted to butadiene-rich products by simply changing the reaction atmosphere from hydrogen to inert gas over the same ETO catalyst. Leveraging the experimental results, baseline techno-economic analysis (TEA) and sensitivity analysis indicate that the ethanol conversion cost is $0.60 per gallon gasoline equivalent (GGE), with opportunities for further cost reduction via improving the liquid hydrocarbon yield and space velocities, and process optimization on balancing dewatering of ethanol feed prior to the ETO step. The minimum fuel selling price (MFSP) of liquid hydrocarbons derived from corn starch ethanol with butadiene as coproduct is $1.64 per GGE, in the range that is cost competitive with petroleum kerosene-type jet fuel. Projected MFSP for cellulosic ethanol (corn stover) derived hydrocarbons is below $3.00 per GGE and co-production of butadiene further reduces the MFSP to $1.70 per GGE. The Well-to-Wake life-cycle analysis indicates that 85% greenhouse gas emission reduction can be achieved when using corn stover compared to petroleum reference and the associated carbon credits will provide significant economic incentives to favor the cellulosic ethanol-derived hydrocarbon fuels. This study demonstrates a low-cost pathway to middle distillate fuels leveraging existing ethanol infrastructure, where catalysis innovation drives the reduction of process complexity and flexible coproduction of a value-added chemical product.

Zhang, Junyan↗
DOE OSTI2021

Evaluation of Safety Standards for Fuel System and Fuel Container Integrity of Alternative Fuel Vehicles

There are two Federal Motor Vehicle Safety Standards (FMVSS) in place that specify requirements for integrity of the fuel system and fuel container on compressed natural gas (CNG) fuel vehicles. These are FMVSS Nos. 303, “Fuel system integrity of compressed natural gas vehicles,” and FMVSS No. 304, “CNG fuel container integrity.” At this time, no FMVSS are defined for the fuel system and fuel container integrity of propane and liquefied natural gas (LNG) vehicles or fuel system integrity requirements for heavy-duty CNG vehicles on the road. However, there are voluntary industry design standards and best practices, as well as regulations defined in other countries. FMVSS No. 303 specifies requirements for the integrity of the CNG fuel system of light-duty vehicles and school buses, and FMVSS No. 304 specifies requirements for fuel container integrity on all CNG vehicles. FMVSS No. 304 applies to containers used for vehicle propulsion, whereas containers used to transport CNG and transportation of CNG containers are regulated by the DOT Pipeline and Hazardous Materials Safety Administration. FMVSS Nos. 303 and 304 are performance-based standards to consistently test and validate equipment and are not design restrictive. Despite the increasing number of natural gas and propane medium- and heavy-duty vehicles on the road, there are no FMVSS fuel system integrity requirements beyond light-duty and school buses for CNG vehicles and no FMVSS fuel system integrity requirements for propane vehicles. NHTSA is researching fuel system safety for medium- and heavy-duty natural gas and propane vehicles to update FMVSS Nos. 303 and 304. NHTSA is also researching current best practices and standards for high pressure fuel tanks in motor vehicles as they may apply to FMVSS No. 304.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Independent Fuel Property Effects of Fuel Volatility on Low Temperature Heat Release and Fuel Autoignition (Final Report)

This Cooperative Research and Development Agreement (CRADA) project between Argonne National Laboratory (ANL), Oak Ridge National Laboratory (ORNL), and Shell Global Solutions (Shell) was initiated as part of a Directed Funding Opportunity (DFO) call for proposals from the Co-Optimization of Fuels and Engines (Co-Optima) initiative. Shell had observed that volatile fuels suppress low temperature heat release (LTHR) more than expected based on conventional gasoline autoignition metrics: research octane number (RON) and motor octane number (MON). The role of LTHR contributes to autoignition phenomena for both boosted spark ignition (BSI) and advanced compression ignition (ACI) combustion modes. ACI combustion modes are applicable to large engines in the hard-to-electrify applications such as off-road, rail, and marine. Thus, having a reliable understanding of autoignition phenomena, including being able to accurately account for the effects of fuel volatility, is particularly important as new synthetic and bio-fuel compositions are considered.This CRADA project aimed to test the hypothesis that the decreased LTHR is due to preferential evaporation of multicomponent fuels when using direct injection (DI) fueling technology, creating composition and reactivity stratification. A custom set of fuels was designed and blended to test this hypothesis by Shell, with experimental engine studies at ORNL and engine combustion modeling by ANL. However, the initial experimental findings did not show the expected effect of fuel volatility suppressing LTHR. Instead, the LTHR propensity observed was independent of the fuel volatility. Due to the unexpected experimental result, the remainder of the experimental effort was redirected to study the effect of fuel volatility on emissions under spark-ignited cold-start conditions. However, as with the LTHR experiments, the cold start effort did not show a meaningful effect of fuel volatility on cold start emissions. Meanwhile, improved engine CFD models have been developed for both LTHR and cold start operations for the Shell fuels with different volatilities. While the simulation efforts were not pursued further due to the insignificant effects of fuel volatility as shown in experiments, the models developed can be easily retooled for off-road, rail, and marine applications.

09 BIOMASS FUELS↗
DOE OSTI2021

Isotopic and Fuel Lattice Parameter Trends in Extended Enrichment and Higher Burnup LWR Fuel Vol I: PWR fuel

Commercial light water reactor (LWR) operators and fuel vendors in the United States are pursuing changes to nuclear fuel that include extended enrichment (EE) and accident-tolerant fuel (ATF) designs. The term EE (8% > 235 U > 5%) is used in this report to refer to a subset of high assay low-enriched uranium (HALEU) that is considered usable in commercial US LWRs in the near term. ATF features are designed to improve fuel system performance under accident conditions. One goal of EE is to improve fuel cycle economy by enabling fuel to be depleted to higher burnup than the typical current maximum pin burnup limits (62 gigawatt-days per metric ton of uranium [GWd/MTU]). Adoption of EE, ATF, and high burnup (HBU) fuels in the US commercial fleet requires a clear understanding of the effects on core physics parameters and used fuel isotopic content, as well as confidence in the accuracy of computer code predictions over an expanded range of materials, enrichment, and burnup. A thorough understanding of the applicability and adequacy of benchmark data (e.g., criticality, decay heat, isotopic content) for computer code validation is necessary to ensure that appropriate safety margins are maintained. To prepare for and support these potential changes, the effects of EE, ATF, and HBU are being assessed for selected representative LWR fuel designs. The project is divided into phases: this report summarizes the findings of Phase 1, which focuses on the lattice physics parameter and used fuel isotopic changes for a conventional Westinghouse 17×17 pressurized water reactor (PWR) design. The primary investigation tool is the SCALE Polaris code using the SCALE 56-group Evaluated Nuclear Data File (ENDF)/B-VII.1 cross sections. The goal of the current work is to (1) identify and explain important effects of EE and HBU (reactivity, lattice physics, and isotopic effects) assuming that PWR fuel design and usage remain similar to those for current enrichment fuel, (2) provide limited code-to-code comparisons with higher order cross section libraries and/or codes, and (3) identify any apparent anomalous trends in the results for further investigation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1997

Fuel Cell Power Plant Initiative: Solid Oxide Fuel Cell/Logistics Fuel Processor 27 kWe Power System Demonstration for ARPA - Volume 1

This report describes the successful testing of a 27 kWe Solid Oxide Fuel Cell (SOFC) generator fueled by natural gas and/or a fuel gas produced by a brassboard logistics fuel preprocessor (LFP). The test period began on May 24, 1995 and ended on February 26, 1996 with the successful completion of all program requirements and objectives. During this time period, this power system produced 118.2 MWh of electric power. No degradation of the generator's performance was measured after 5582 accumulated hours of operation on these fuels: local natural gas - 3261 hours, jet fuel reformate gas - 766 hours, and diesel fuel reformate gas - 1555 hours. This SOFC generator was thermally cycled from full operating temperature to room temperature and back to operating temperature six times, because of failures of support system components and the occasional loss of test site power, without measurable cell degradation. Numerous outages of the LFP did not interrupt the generator's operation because the fuel control system quickly switched to local natural gas when an alarm indicated that the LFP reformate fuel supply had been interrupted. The report presents the measured electrical performance of the generator on all three fuel types and notes the small differences due to fuel type. Operational difficulties due to component failures are well documented even though they did not affect the overall excellent performance of this SOFC power generator. The final two appendices describe in detail the LFP design and the operating history of the tested brassboard LFP.

Veyo, S.E.↗
DOE OSTI2023

Advanced Fuel Cycle Cost Basis Report: Module D1-4 and Module D1-5 Ceramic Pelletized Sodium-Cooled Fast Reactor (SFR) Fuel Fabrication Ceramic Vibrocompacted Fuel Fabrication

This is a cost module that is part of the Advanced Fuel Cycle -- Cost Basis Report. Module D1-4: Nature of this module update (Rev 1) from previous advanced fuel cycle cost basis reports (AFCCBRs): new life cycle cost data on U,Pu SFR mixed oxide (MOX) fuels is derived from the Nonproliferation Assessment Systems Analysis Program (NASAP) conducted in the late 1970s. Highassay low-enriched uranium (HALEU) ceramic fuel is also discussed in more detail compared to earlier AFC-CBRs, since some advanced SFR concepts currently under development will require this HALEU fuel type for startup. Module D1-5: Nature of this FY-21 module update from previous AFC-CBRs: this module includes a few new references and a somewhat expanded discussion of vibrocompaction fuel fabrication technology. The WIT values for VIPAC are pegged directly to those for conventional LWR and SFR pelletized U,Pu MOX (note that this module now includes VIPAC MOX fuel for LWRs in addition to SFRs). Based on information from Russia, where VIPAC has been studied extensively, the unit costs are expressed as a percentage of those in the new updated Module D1-2 (pelletized U,Pu MOX) and new updated Module D1-4 (pelletized U,Pu MOX) for large NOAK fabrication facilities of the same production capacity. Since both ceramic pelletized MOX Modules D1-2 and D1-4 benefitted from analysis of 1970s NASAP data, by extension this Module D1-5 also benefits.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Case Study: Resilience Benefits of Distributed Wind Against Fuel and Weather Hazards in Alaska

In this case study of St. Mary’s Village, Alaska, we present a resilience evaluation exercise. A resilience framework is employed to identify system characteristics, relevant metrics, and resilience hazards and to assess the performance against the hazards with and without a distributed wind system installed. The results show the resilience benefits provided by the distributed wind installation against fuel shortage hazards and cold weather hazards. The resilience benefits can be assigned monetary values, which will be highly dependent on actual circumstances of the hazard, but provide insight into value streams of distributed wind that are not usually considered. For example, the single 900 kW turbine was found to prevent an average of 14,643 kWh of load from being dropped during a two-day diesel fuel shortage event, which saved the community $447,592 from the prevented outages. This case study serves as an example for novel power system resilience analysis and builds understanding of resilience hazards that are common across many power systems.

Culler, Megan J.↗
NASA NTRS1930

Fuel Vapor Pressures and the Relation of Vapor Pressure to the Preparation of Fuel for Combustion in Fuel Injection Engines

This investigation on the vapor pressure of fuels was conducted in connection with the general research on combustion in fuel injection engines. The purpose of the investigation was to study the effects of high temperatures such as exist during the first stages of injection on the vapor pressures of several fuels and certain fuel mixtures, and the relation of these vapor pressures to the preparation of the fuel for combustion in high-speed fuel injection engines.

Joachim, William F↗
DOE OSTI2023

Nuclear fuel rods and heat pipes in a graphite moderator matrix for a micro-reactor, with the fuel rods having fuel pellets in a BeO sleeve

A reactor unit cell is disclosed including a graphite moderator structure, a heat pipe positioned in the graphite moderator structure, and a fuel assembly positioned in the graphite moderator structure. The fuel assembly comprises at least one fuel rod. Each fuel rod comprises a beryllium-oxide sleeve and nuclear fuel positioned in the beryllium-oxide sleeve.

Levinsky, Alex↗
NASA NTRS1981

Low NO/x/ combustion systems for burning heavy residual fuels and high-fuel-bound nitrogen fuels

Design concepts are presented for lean-lean and staged rich-lean combustors. The combustors are designed for the dry reduction of thermal NO(x), control of NO(x) from fuels containing high levels of organic nitrogen, and control of smoke from low hydrogen content fuels. The combustor concepts are tested with a wide variety of fuels including a middle distillate, a petroleum based heavy residual, a coal derived synthetic, and ratios of blends of these fuels. The configurations of the lean-lean and rich-lean combustion systems are provided along with a description of the test rig and test procedure.

White, D. J.↗