Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fluid injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Qualitative investigation of cryogenic fluid injection into a supersonic flow field

The behavior of liquid nitrogen injected into a supersonic nitrogen flow field was investigated using an experimental apparatus in which a Mach 2.7 2D gas nitrogen tunnel is coupled with a high-pressure cryogenic source. Observations were monitored and recorded via a video camera and a motion picture camera. It was found that the penetration of a supersonic flow field by injection of liquid nitrogen is strongly dependent on the flow Mach number, the cryogen injection pressure (Pi/Pc), the injector configuration, and the cryogen temperature. For a 2D gaseous N2, Mach 2.7 tunnel, with cryogen injection Pi/Pc approaching 2, the injected fluid penetration for the 1/8-in. injection port approached one half of the tunnel width at 90-deg injection, and one fourth of the tunnel width at 20-deg injection.

Hendricks, R. C.↗
DOE OSTI2020

Imaging of a fluid injection process using geophysical data — A didactic example

In many subsurface industrial applications, fluids are injected into or withdrawn from a geologic formation. It is of practical interest to quantify precisely where, when, and by how much the injected fluid alters the state of the subsurface. Routine geophysical monitoring of such processes attempts to image the way that geophysical properties, such as seismic velocities or electrical conductivity, change through time and space and to then make qualitative inferences as to where the injected fluid has migrated. The more rigorous formulation of the time-lapse geophysical inverse problem forecasts how the subsurface evolves during the course of a fluid-injection application. Using time-lapse geophysical signals as the data to be matched, the model unknowns to be estimated are the multiphysics forward-modeling parameters controlling the fluid-injection process. Properly reproducing the geophysical signature of the flow process, subsequent simulations can predict the fluid migration and alteration in the subsurface. The dynamic nature of fluid-injection processes renders imaging problems more complex than conventional geophysical imaging for static targets. This work intents to clarify the related hydrogeophysical parameter estimation concepts.

58 GEOSCIENCES↗
DOE OSTI2024

Utah FORGE: Temperature-Dependent Fracture Seismicity from Fluid Injection Experiments

This dataset contains experimental data from fluid injection experiments conducted to investigate the influence of temperature on fracture seismicity. The experiments were performed on granite samples from Utah FORGE. The samples were prepared with a 30-degree inclined fracture and subjected to controlled stress and temperature conditions. Data were collected under three distinct temperature settings: 24 C, 78 C, and 137 C. During the experiments, a constant confining pressure of 10 MPa and a constant shear stress at 80% of the shear strength of the sample were maintained. Pore pressure was incrementally increased at a rate of 300 kPa every three minutes to simulate fluid injection. Temperature was raised rapidly and then stabilized for the duration of each test. The dataset includes shear stress and displacement measurements under each temperature condition, along with supplementary figures illustrating the experimental setup and time-series plots of pressures and temperature.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Pressurized damping fluid injection for damping turbine blade vibration

A blade vibration damping system impacts a pressurized damping fluid on a surface of at least one of a plurality of blades of a turbine in opposition to a vibratory movement thereof to cause damping of vibration of the blade(s) during operation of the turbine. The system includes a fluid injection nozzle in a stationary component adjacent the plurality of blades. A valve selectively admits the pressurized damping fluid to the fluid injection nozzle from a source of pressurized damping fluid, and a control system controls the valve to operate the fluid injection nozzle in response to an operational parameter exceeding a threshold during operation of the turbine. A related turbine casing and method are also provided.

Delvaux, John McConnell↗
DOE OSTI2023

Utah FORGE: Fault Reactivation Through Fluid Injection Induced Seismicity Laboratory Experiments

Included are results from shear reactivation experiments on laboratory faults pre-loaded close to failure and reactivated by the injection of fluid into the fault. The sample comprises a single-inclined-fracture (SIF) transecting a cylindrical sample of Westerly granite. All experiments are conducted at ambient temperature and follow a similar protocol: (i) application of confining stresses (3MPa) on the fault fully saturated with DI water, (ii) shear-mobilization through the increase of axial loading at a constant displacement rate until a post-peak steady-state condition is reached, (iii) reduction of axial loading and related shear stress to a prescribed fraction of the peak steady-state frictional strength (typically 60% to 90%, representing intermediate to high magnitudes) and (iv), fault reactivation triggered by a stepwise increase of pore pressure on the fault in 0.1 MPa increments held constant for 1-5 minutes. Mechanical data from three ISCO pumps connected to a Temco pressure vessel measure axial, confining, and fault-related parameters, including fluid pressure (kPa), fluid flow rate (mL/min), and axial displacement (mm). See included code for initial data analysis and visualization for select experiments. Resource names represent experiment numbers found in the "Read Me" file, which describes each experimental setup and parameters.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Geomechanical response due to nonisothermal fluid injection into a reservoir

The geomechanical response of a porous reservoir due to injection of fluid can result from a complex interplay between the changes in porepressure and temperature near the wellbore. As a result, predictions are usually made using either simplified analytical models, which may apply unrealistic assumptions in order to produce a tractable model, or detailed numerical simulations that can be computationally expensive.

58 GEOSCIENCES↗
NASA NTRS1990

Numerical study of subcritical flow with fluid injection

It is suggested that the study of synthetic flows, where controlled experiments can be performed, is useful in understanding turbulent flow structures. The early states of formation of hairpin structures in shear flows and the subsequent evolution of these structures is studied in shear flows and the subsequent evolution of these structures is studied through numerical simulations, by developing full-time dependent three-dimensional flow solution of an initially laminar (subcritical) flow in which injection of fluid through a narrow streamwise slot from the bottom wall of a plate is carried out. Details of the numerical approach and significance of the present findings are reported in this work.

Balasubramanian, R.↗
DOE OSTI2021

Field-scale fault reactivation experiments by fluid injection highlight aseismic leakage in caprock analogs: Implications for CO 2 sequestration

Observations on tens-of-meter scale experiments of fault activation by fluid injection conducted in shales allow exploring how aseismic and seismic events may jeopardize the integrity of a sealing caprock overlying a CO 2 sequestration reservoir. We contrast the behavior of shale faults with another set of experiments conducted in carbonates. Significant fluid leakage occurs along the initially low-permeability shale faults when rupture is activated. Most of the leakage pathway closes when fluid injection ceases and fluid pressure drops. Dilatant slip on the fault plane alone does not explain the observed leakage behavior, which is also caused by fault opening favored by the softness of the shale, and by the structure of the fault zone that prevents fluids from diffusing into the adjacent damage zone. Experiments show a large amount of aseismic deformation. Small-magnitude seismicity (M w < -2.5) is observed outside the pressurized leakage patch. Stress transferred from this aseismic deformation patch can build up to stress-criticality and favor seismicity. Thus, in terms of fault activation in caprocks, aseismic fault slip leading to increased permeability and a loss of seal integrity is of great concern.

58 GEOSCIENCES↗
DOE OSTI2020

Estimating perturbed stress from 3-D borehole displacements induced by fluid injection in fractured or faulted shales

SUMMARY Hydrofracturing stress measurements in fractured and anisotropic shales are notoriously difficult, because opening of existing geological features tends to prevent the creation of a pure hydraulic fracture perpendicular to the least compressive principal stress. Here we show how adding 3-D borehole-displacement measurements while conducting the hydraulic injection test helps to better constrain the principal stress orientations and magnitudes. We developed a 3-D fully coupled hydromechanical numerical model to analyse the displacement, fluid pressure and injection flow-rate data measured during an injection pressure-step-rate test conducted to activate a faulted borehole interval in the Mont Terri Opalinus Clay (Switzerland). We find that injected fluids can only penetrate the fault when it is at or above the Coulomb failure pressure. Borehole displacement orientations are sensitive to a ∼15° variation in the stress–tensor orientation and a 1 MPa stress magnitude variation. Although some dispersion occurs while rupture is propagating along the fault plane ∼4 m away from the borehole, the maximum density of displacement orientations consistently informs about the stress orientation. Thus, an extended injection step-rate approach coupled with an accurate in situ measurement of the borehole wall displacements can be used to better constrain the local stress field perturbations in fractured shales and in heterogeneous rock in general.

Guglielmi, Yves↗
DOE OSTI2022

Transient mixing behavior of a supercritical fluid injected into supercritical and subcritical environments

Transient, near-field mixing of a supercritical fluid injected into supercritical and subcritical environments is investigated experimentally. Fuel (propane) from a 100 μm diameter Bosch diesel injector is injected into a high-pressure test rig with a steady flow of heated, low-velocity nitrogen to control the ambient pressure and temperature. The fuel supply pressure is approximately 190 bar, allowing short injections lasting 3–4 ms to be performed in quick succession to acquire statistically significant datasets to represent the unsteady fuel–air mixing. Two test cases with the same ambient density and injector inlet pressure and temperature were chosen in an attempt to isolate effects of mixture phase behavior. Microscopic rainbow Schlieren deflectometry (RSD) is used for visualization and quantitative data acquisition. In the case of the supercritical ambient, the injector inlet and exit and ambient conditions are all supercritical. The RSD analysis reveals a mixing process similar to the single phase fluid mixing, though condensation is also observed locally, and can be explained by the adiabatic mixing theory presented in the paper. For the subcritical ambient case, the injector inlet is supercritical, but the injector exit and ambient conditions are both subcritical. The results show a rapid expansion in the near-field promoting mixing between propane and nitrogen. At downstream locations, significant condensation is also observed as predicted by the adiabatic mixing theory. As a result, the supercritical ambient case exhibited longer and narrower jet penetration compared to the subcritical ambient case.

02 PETROLEUM↗
DOE OSTI2024

Surface Deformation and Seismicity Linked to Fluid Injection in the Raton Basin

Abstract It is suggested that in addition to seismicity deep fluid injection may cause surface uplift and subsidence in oil and gas‐producing regions. This study uses the Raton Basin as an example to investigate the hydromechanical processes of surface uplift and subsidence during wastewater injection. The Raton Basin, in southern central Colorado and northern central New Mexico, has experienced wastewater injection related to coalbed methane and gas production starting in 1994. In this study, we estimate the extent and magnitude of total vertical deformation in the Raton Basin from 1994 to 2020 and incremental deformation between the years 2017 to 2020. Results indicate a modeled uplift as much as 15 cm occurring between 1994 and 2020. Between 2017 and 2020, up to 3 cm of uplift occurred, largely near the northwestern injection wells. Most modeled uplift between 1994 and 2020 occurred near the southern wells, where the greatest cumulative volume of wastewater was injected. However, modeled subsidence occurred around the southern and eastern wells between 2017 and 2020, after the rate of injection decreased. Modeling indicates that while the magnitude of modeled uplift corresponds to cumulative injection volume and maximum rate in the long‐term, short‐term incremental deformation (uplift or subsidence) is controlled by changes in the rate of injection. The number of yearly earthquake events follows periods of rapid modeled uplifting throughout the Basin, suggesting that measurable surface deformation may be caused by the same injection‐induced pore pressure perturbations that initiate seismicity.

Geology↗
NASA NTRS1991

A qualitative view of cryogenic fluid injection into high speed flows

The injection of supercritical pressure, subcritical temperature fluids, into a 2-D, ambient, static temperature and static pressure supersonic tunnel and free jet supersonic nitrogen flow field was observed. Observed patterns with fluid air were the same as those observed for fluid nitrogen injected into the tunnel at 90 deg to the supersonic flow. The nominal injection pressure was of 6.9 MPa and tunnel Mach number was 2.7. When injected directly into and opposing the tunnel exhaust flow, the observed patterns with fluid air were similar to those observed for fluid nitrogen but appeared more diffusive. Cryogenic injection creates a high density region within the bow shock wake but the standoff distance remains unchanged from the gaseous value. However, as the temperature reaches a critical value, the shock faded and advanced into the supersonic stream. For both fluids, nitrogen and air, the phenomena was completely reversible.

Hendricks, R. C.↗
DOE OSTI2022

Subsurface stress criticality associated with fluid injection and determined using machine learning

Machine-learning methods and apparatus are disclosed to determine critical state or other parameters related to fluid-driven failure of a terrestrial locale impacted by anthropogenic activities such as hydraulic fracturing, hydrocarbon extraction, wastewater disposal, or geothermal harvesting. Acoustic emission, seismic waves, or other detectable indicators of microscopic processes are sensed. A classifier is trained using time series of microscopic data along with corresponding data of critical state or failure events. In disclosed examples, random forests and artificial neural networks are used, and grid-search or EGO procedures are used for hyperparameter tuning. Once trained, the classifier can be applied to live data from a fluid injection locale in order to assess a frictional state, assess seismic hazard, assess permeability, make predictions regarding a future fluid-driven failure event, or drive engineering solutions for mitigation or remediation. Variations are disclosed.

Johnson, Paul Allan↗
NASA NTRS1955

The Compressible Laminar Boundary Layer with Fluid Injection

A solution of the equations of the compressible laminar boundary layer including the effects of transpiration cooling is presented. The analysis applies to the flow over an isothermal porous plate with a velocity of fluid injection proportional to the reciprocal of the square root of the distance from the leading edge. The effect of several flow parameters on coolant-flow rates is discussed with the aid of representative examples. A stability analysis indicates that, although transpiration cooling requires a lower surface temperature for stable flow than does internal wall cooling, this lower temperature can be obtained with a smaller expenditure of coolant.

Low, George M↗
DOE OSTI2024

Forecasting fluid-injection induced seismicity to choose the best injection strategy for safety and efficiency

Induced seismicity poses a challenge to the development of Enhanced Geothermal Systems (EGS). Improving monitoring and forecasting techniques is essential to mitigate induced seismicity and thereby fostering a positive perception of EGS projects among local authorities and population. Induced seismicity is the result of complex and coupled thermo-hydro-mechanical-chemical mechanisms. Injection flux and pressure are crucial controlling parameters for both hydraulic stimulation and circulation protocols. We develop a methodology combining a hydro-mechanical model with a seismicity rate model to estimate the magnitude and frequency of mainshocks and aftershocks induced by fluid injection. We apply the methodology to the case of the Basel EGS (2006, Switzerland) to compare the effects of progressive, cyclic and constant injections on the mechanical response of discrete faults. Results from the coupled hydro-mechanical models show that the pore pressure diffusion and consequent enhancement of fault permeability are limited to the vicinity of the injection well during cyclic injection. Additionally, constant injection induces seismicity from the start of the injection but enhances the permeability of most of the faults within a shorter duration, inducing less post-injection seismicity. The methodology can be adapted to any numerical model and allows new projects to be developed by anticipating the safest injection protocol. This article is part of the theme issue ‘Induced seismicity in coupled subsurface systems’.

58 GEOSCIENCES↗
NASA NTRS1950

An analysis of supersonic aerodynamic heating with continuous fluid injection

An analysis of the steady-state aerodynamic heating problem at high-supersonic speeds is made for two-dimensional flows with laminar boundary layers. The aerodynamic heating is shown to be reduced substantially by injecting a small amount of coolant through a porous surface into the boundary layer. The analysis includes calculations of the cooling requirements and equilibrium surface temperatures for flat plates and for an equilibrium surface temperatures for flat plates and for flat porous surfaces with several rates of fluid injection at Mach numbers from 5 to 15 and altitudes from sea level to 200,000 feet. Some calculations of the skin friction are also included.

Klunker, E G↗
DOE OSTI2023

Simple Statistical Models for Predicting Overpressure Due to CO2 and Low-Salinity Waste-Fluid Injection into Deep Saline Formations

Deep saline aquifers have been used for waste-fluid disposal for decades and are the proposed targets for large-scale CO2 storage to mitigate CO2 concentration in the atmosphere. Due to relatively limited experience with CO2 injection in deep saline formations and given that the injection targets for CO2 sometimes are the same as waste-fluid disposal formations, it could be beneficial to model and compare both practices and learn from the waste-fluid disposal industry. In this paper, we model CO2 injection in the Patterson Field, which has been proposed as a site for storage of 50 Mt of industrial CO2 over 25 years. We propose general models that quickly screen the reservoir properties and calculate pressure changes near and far from the injection wellbore, accounting for variable reservoir properties. The reservoir properties we investigated were rock compressibility, injection rate, vertical-to-horizontal permeability ratio, average reservoir permeability and porosity, reservoir temperature and pressure, and the injectant total dissolved solids (TDS) in cases of waste-fluid injection. We used experimental design to select and perform simulation runs, performed a sensitivity analysis to identify the important variables on pressure build-up, and then fit a regression model to the simulation runs to obtain simple proxy models for changes in average reservoir pressure and bottomhole pressure. The CO2 injection created more pressure compared to saline waste-fluids, when similar mass was injected. However, we found a more significant pressure buildup at the caprock-reservoir interface and lower pressure buildup at the bottom of the reservoir when injecting CO2 compared with waste-fluid injection.

Ansari, Esmail↗