Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Carbon Fiber Plasma Surface Treatment (CRADA Final Report)

This project focused on developing and applying a new surface treatment technology to carbon fiber applications. During the course of this work, two different treatment prototypes were developed and explored. Highly reactive surface chemistries were successfully applied to carbon fiber, resulting in surface oxygen content as high as 27%. Enhanced composite properties of a 45% increase in the interfacial strength and a 10% increase in tensile and flexural strength were demonstrated for thermoplastic resins. This enhancement was performed while proving that the plasma surface treatment process does not damage the fiber. Treatment times were as low as 1 min.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multiscale modeling-enabled design of multifunctional composites

This study aims to create a comprehensive model that considers multiple scales and physics for predicting the electromechanical behavior of fiber-reinforced composites enhanced with barium titanate (BaTiO3). In our earlier work, we have demonstrated that depositing BaTiO3 microparticles of 200-nm-diameter, on fiber surfaces during fiber-reinforced composite fabrication enhances mechanical strength, passive self-sensing, and energy harvesting properties. The key is to carefully control the microparticle concentration to prevent agglomeration. Since the particles are micron-sized, understanding how agglomeration affects the composites' electromechanical properties is crucial for guiding such multifunctional materials’ design. This study introduces a micromechanics-based approach to explore the impact of microparticle dispersion on the bulk composites' electromechanical properties. Insights gained from this investigation are applied in experiments, enabling accurate predictions of mechanical and self-sensing responses in BaTiO3-enhanced fiber-reinforced composites. Micro-level findings from this computational approach can be integrated into larger continuum models to comprehensively capture the electromechanical behavior of the composite structures at bulk scale. The proposed model is validated by comparing predictions with experimental results, accounting for the nonlinear mechanical and electromechanical behaviors of constituent materials. Consequently, this computational model serves as a digital platform for efficiently designing multifunctional composites.

Gupta, Sumit↗
DOE OSTI2023

Rheology of concentrated fiber suspensions with a load-dependent friction coefficient

Here we investigate the effects of fiber aspect ratio, roughness, flexibility, and volume fraction on the rheology of concentrated suspensions in a steady shear flow using direct numerical simulations. We model the fibers as inextensible continuous flexible slender bodies with the Euler-Bernoulli beam equation governing their dynamics suspended in an incompressible Newtonian fluid. The fiber dynamics and fluid flow coupling is achieved using the immersed boundary method. In addition, the fiber surface roughness might lead to interfiber contacts, resulting in normal and tangential forces between the fibers, which follow Coulomb’s law of friction. The surface roughness is modeled as hemispherical protrusions on the fiber surfaces. Their deformation results in a normal load-dependent friction coefficient. Our simulations accurately predict the experimentally observed shear thinning in fiber suspensions. Furthermore, we find that the suspension viscosity η increases with increasing the volume fraction, roughness, fiber rigidity, and aspect ratio. The increase in η is the macroscopic manifestation of a similar increase in the microscopic contact contribution to the total stress with these parameters. In addition, we observe positive and negative first N 1 and second N 2 normal stress differences, respectively, with |N 2 | < |N 1 |, in agreement with previous experiments. Last, we propose a modified Maron-Pierce law to quantify the reduction in the jamming volume fraction by increasing the fiber aspect ratio and roughness. Our results and analysis establish the use of fiber surface tribology to tune the suspension flow behavior.

42 ENGINEERING↗
DOE OSTI2025

Electroplated Polymer‐Modified Carbon Fiber for Performance‐Enhancing Composite Interfaces

Carbon fiber composite performance relies on the fiber-matrix interface for effective load transfer. To enhance interfacial properties between the fiber and matrix, often carbon fiber surfaces are oxidatively and covalently modified to incorporate chemical functional groups. By contrast, here, noncovalent electrodeposition of functional polyelectrolyte is applied onto conducting carbon fibers from aqueous solutions. A natural polymer, chitosan (CS), is electro-deposited onto the fiber surface, which undergoes multi-scale physical interactions. The bound CS layer with abundant amine functionalities reacts with epoxy moieties within the matrix to improve the interfacial properties. The scalable and energy-efficient electrodeposition eliminates traditional functionalization and sizing requirements of carbon fiber while delivering significantly higher mechanical performance with enhanced consistency. For continuous fiber reinforced composites, compared to conventional fibers, apparent interlaminar shear strength increases by 27%, reaching ≈86 MPa. The short fiber composites with only 2–11 wt.% fibers exhibit ≈20% increase in tensile strength with a peak performance of 120 MPa. Unlike traditionally treated and sized carbon fiber, this approach delivers coated fibers with long shelf-life and allows recovery of both CS in electrolyte form and carbon fiber by continuous electrochemical processing of the modified fibers with inverse polarity; thus, it promotes overall fiber recyclability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fiber Uncertainty Visualization for Bivariate Data With Parametric and Nonparametric Noise Models

Visualization and analysis of multivariate data and their uncertainty are top research challenges in data visualization. Constructing fiber surfaces is a popular technique for multivariate data visualization that generalizes the idea of level-set visualization for univariate data to multivariate data. Here, in this paper, we present a statistical framework to quantify positional probabilities of fibers extracted from uncertain bivariate fields. Specifically, we extend the state-of-the-art Gaussian models of uncertainty for bivariate data to other parametric distributions (e.g., uniform and Epanechnikov) and more general nonparametric probability distributions (e.g., histograms and kernel density estimation) and derive corresponding spatial probabilities of fibers. In our proposed framework, we leverage Green's theorem for closed-form computation of fiber probabilities when bivariate data are assumed to have independent parametric and nonparametric noise. Additionally, we present a nonparametric approach combined with numerical integration to study the positional probability of fibers when bivariate data are assumed to have correlated noise. For uncertainty analysis, we visualize the derived probability volumes for fibers via volume rendering and extracting level sets based on probability thresholds. We present the utility of our proposed techniques via experiments on synthetic and simulation datasets.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Interfacial Strength in Hierarchical Carbon Fiber Composites: Interplay of Interphase Modulus and Roughness

A facile, direct deposition approach that exploits van der Waals interactions between carbonaceous materials is utilized to create unidirectional hybrid carbon fiber composites. Two small molecule crosslinkers, a trifunctional aromatic (TL) and a difunctional aliphatic (DL) acyl chloride, are first utilized to create a crosslinked interphase with a softer and stiffer modulus respectively. TL crosslinked interphase with a higher modulus improved the tensile strength by 50%, despite non-covalent linking between fiber and matrix, elucidating the critical role of the interphase in alleviating modulus mismatch between the high modulus carbon fiber and the rubbery matrix. Fractional quantities of carbon nanotubes are additionally dispersed in the small molecule crosslinkers which behaved as a dispersant, helping introduce nanoasperities on the carbon fiber surface. Strong “pi-pi” interactions between CNTs and CF contributed to tensile properties, which are increased by 66% compared to the control. A cohesive zone model suggests that a stiffer interphase is better able to exploit surface heterogeneities and roughness on the fiber, synergistically enhancing interfacial strength.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A mild calcium carbonate treatment improves moisture resistance and mechanical/interfacial properties of jute and hemp fibers

Natural fibers are attractive, sustainable reinforcements, but often exhibit high moisture uptake and weak bonding with polymer matrices. In this study, jute and hemp were treated by immersion in aqueous calcium carbonate (CaCO3) suspensions (10–40?wt.%, 1.5?h, room temperature) and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), moisture sorption testing, single-fiber tensile testing, and bundle pull-out testing. SEM showed granular CaCO3 deposition on fiber surfaces, with particulates bridging surface voids and microcracks. At 40 wt.% CaCO3, equilibrium moisture uptake decreased to ~5% (hemp) and ~3% (jute), while tensile strength increased to ~904 MPa (hemp) and ~960 MPa (jute). Apparent interfacial shear strength from pull-out testing increased up to ~1.35 MPa (hemp) and ~0.56 MPa (jute). These results indicate that CaCO3 deposition is a mild, scalable surface treatment that improves moisture resistance, fiber tensile strength, and interfacial load transfer relevant to semi-structural composite applications, including interior and secondary automotive components.

Calcium carbonate treatment↗
DOE OSTI2025

Conversion of Waste PET Plastic to Aramid Fiber

A three-step synthesis was used to convert waste polyethylene terephthalate (PET) into the high value polymer, poly-para-phenylene terephthalamide (PPTA), used in the production of high strength aramid fiber, such as Kevlar. Improvements to the polymerization reaction by addition of calcium chloride to the solvent, N-methyl-2-pyrrolidone (NMP), and rigorous anhydrous conditions enabled the production of a PET-derived PPTA with a 4.15 dL/g inherent viscosity in sulfuric acid that is amenable to fiber spinning. PPTA fibers were spun using a wet spinning apparatus under varied process parameters to assess their impact on fiber surface morphology, diameter, and the mechanical properties of the fibers. Select fibers were subjected to a post-spinning heat treatment at 150 °C , which improved the tensile strength and modulus by 100% and 30%, respectively, relative to the as-spun fibers. Techno-economic and life cycle analyses were conducted to evaluate the economic feasibility and the life-cycle greenhouse gases (GHG) emissions of the approach. In conclusion, the results suggest the potential for up to a 30% cost reduction, and comparable GHG emissions against conventional petroleum-based processes.

Lifecycle Analysis↗
DOE OSTI2025

Coal to Carbon Fiber (C2CF) Continuous Processing for High Value Composites (Final Report)

Coal tar is a condensed and recovered by-product of the coking of metallurgical coal for steel production. The heaviest fraction of distilled coal tar is an isotropic pitch largely used as a binder in the manufacturing of carbonaceous electrodes for primary aluminum smelting and in electric arc furnaces. Coal tar pitch offers high carbon yield upon carbonization. In this project, a process to convert the domestically sourced isotropic coal tar pitch, containing very low particulates (QI = 0.32 wt.%), to form flow-domain mesophase pitch amenable for melt spinning into precursor (green) fibers for carbon fiber, was developed and optimized. The final reproducible processing developed is reviewed in this report, along with several characterizations of the mesophase pitch. A final definition of the characteristics of a ‘spinnable’ mesophase pitch is presented. With this mesophase pitch, reproducible and stable multifilament melt spinning was developed, producing green fiber tows with filament diameters of approximately 20 m. The multifilament melt spinning was the most challenging aspect of the project and required the most effort. The best practices learned from this project for melt spinning are reviewed in this report. Once spun, the green fibers were oxidatively stabilized, carbonized and graphitized under inert gas atmosphere to form the final carbon fibers. Given the relatively high softening point of the mesophase pitch, no issues of interfilament fusion were observed during batch oxidation, and subsequent batch carbonization and graphitization went smoothly in all cases. An ~ 80 wt.% conversion of the green fiber mass to final carbon fiber was achieved. After graphitization, the carbon fibers showed high tensile moduli (most were ~ 600 GPa, or 87 Msi) consistent with commercially-available high-performance pitch-based carbon fiber. However, tensile strength and strain to failure were comparatively low. Further work to reduce defects in and on the fiber surfaces would increase these properties. SEM imaging of the graphitic fiber textures is presented herein. Rudimentary composites were fabricated from the carbon fibers and characterized showing similar modulus to baseline composites fabricated with commercial carbon fiber. Finally, a basic economic analysis was done showing the potential to increase the value of the isotropic coal tar pitch by up to 13.6 to 136 times based on a carbon fiber value of $\$$5/lb to $\$$50/lb, respectively. Moreover, the site case study suggests that the coal tar from the single integrated steel mill could supply production of up to 16 kt/yr of carbon fiber. Finally, a technological gap analysis was done which shed light on remaining technical challenges. These challenges included: recovery and utilization of condensates from the mesophase pitch processing, further advancing and increasing stability of the multifilament melt spinning processing, optimization of the oxidation processing, defect reduction for increased carbon fiber strength, and the development of a weaving process towards carbon fiber fabrics. To maximize the coal value chain, the primary objectives of this project were to (a) develop and scale efficient processing technology for producing melt-spinnable mesophase pitch from isotropic coal tar pitch, (b) clarify and simplify tedious continuous fiber processing technologies (particularly multifilament melt spinning of mesophase pitch) towards the efficient production of high performance carbon fiber, and (c) demonstrate and characterize representative composite parts derived from the final carbon fiber. Immense progress was made on all 3 objectives and is detailed in this report.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Investigating the Electromechanical Sensitivity of Carbon-Nanotube-Coated Microfibers

The piezoresistance of carbon nanotube (CNT)-coated microfibers is examined using diametric compression. Diverse CNT forest morphologies were studied by changing the CNT length, diameter, and areal density via synthesis time and fiber surface treatment prior to CNT synthesis. Large-diameter (30–60 nm) and relatively low-density CNTs were synthesized on as-received glass fibers. Small-diameter (5–30 nm) and-high density CNTs were synthesized on glass fibers coated with 10 nm of alumina. The CNT length was controlled by adjusting synthesis time. Electromechanical compression was performed by measuring the electrical resistance in the axial direction during diametric compression. Gauge factors exceeding three were measured for small-diameter (<25 μm) coated fibers, corresponding to as much as 35% resistance change per micrometer of compression. The gauge factor for high-density, small-diameter CNT forests was generally greater than those for low-density, large-diameter forests. A finite element simulation shows that the piezoresistive response originates from both the contact resistance and intrinsic resistance of the forest itself. The change in contact and intrinsic resistance are balanced for relatively short CNT forests, while the response is dominated by CNT electrode contact resistance for taller CNT forests. These results are expected to guide the design of piezoresistive flow and tactile sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Versatile Fiber Coating Process for Efficient Fabrication of Multifunctional Composites

The objective of this research is to demonstrate the versatility of a dip coating process for the efficient integration of piezoelectric barium titanate (BaTiO3) microparticles on a wide variety of fibers to design passive self-sensing composites. The microparticles were deposited on glass, aramid, and basalt fiber weaves through the proposed dip coating technique. A computational framework is established to predict the deposition thickness on the fiber surfaces from the given microparticle concentration, size, coating velocity, and coating fluid viscosity. The deposition quality assessment was performed through scanning electron microscope imaging and subsequent image analysis. BaTiO3-coated fibers were directly used in composite preparation. After fabrication, the BaTiO3-enhanced composites were subjected to high-voltage poling. Finally, their passive self-sensing properties were characterized through experimental studies. The results show the adaptability of the proposed coating process to integrate BaTiO3 microparticles within different types of fiber-reinforced composites enabling passive self-sensing to attain subsurface damage characterization.

Gupta, Sumit↗
DOE OSTI2023

Electrospun Nanofiber Electrodes for High and Low Humidity PEMFC Operation

MEAs with nanofiber mat electrodes containing Pt/C catalyst and Nafion binder were fabricated and evaluated. The electrodes were prepared by electrospinning a solution of catalyst powder, salt-form Nafion (with Na + , Li + , or Cs + as the sulfonic acid counterion), and a carrier polymer of either polyethylene oxide or poly(acrylic acid). The carrier polymer was extracted prior to MEA testing by a hot water soaking step. The resulting fibers were 15%–17% porous, with a core–shell-like morphology (a coating of primarily Nafion on the fiber surface). MEAs with anode/cathode catalyst loadings of 0.1 mg Pt cm −2 each and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions in H 2 /air fuel cell tests, e.g., a maximum power density of 919 mW cm −2 at 100% RH and 832 mW cm −2 at 40% RH for a test at 80 °C and 200 kPa abs . The presence of nm-size pores within the fibers trapped water via capillary condensation during low RH feed gas testing, thus maintaining a high proton conductivity of the Nafion binder in the anode and cathode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder.

25 ENERGY STORAGE↗
DOE OSTI2026

Toward Rapid Actinium-225 Purification via Membrane Adsorbers with Covalently Tethered Diglycolamide Ligands

Extractive diglycolamide (DGA) resins are used in several state-of-the-art techniques for purifying 225 Ac, a promising radiometal for targeted alpha therapy. Unfortunately, separation processes that rely on resins are often limited to slow flow rates, high elution volumes, and long processing times. Membrane adsorbers functionalized with DGA ligands are an alternative separation material that may overcome these challenges. This work presents (1) the synthesis of an aminated tetrahexyldiglycolamide ligand, (2) the covalent tethering of the ligand to electrospun poly(vinylbenzyl chloride) fiber mats, and (3) the adsorption and desorption of La(III) and 225 Ac. Chemical and physical characterization supports the covalent tethering of the ligand to the fiber mat, as well as the preservation of the fiber surface area and porosity after functionalization. Equilibrium adsorption experiments were performed with stable La(III) and radioactive 225 Ac. Trends in affinity are consistent between commercial resins and the synthesized membrane adsorbers; however, the Langmuir constants and the maximum binding capacity of the membrane adsorbers were generally lower than the resins. Despite these differences, the modeled selectivity for an equimolar solution of La(III)/ 225 Ac in 10 M nitric acid is 57. Furthermore, 225 Ac is rapidly desorbed from the fibers in 10 M nitric acid (<20 min). The La(III)/ 225 Ac selectivity and rapid 225 Ac desorption indicate this class of materials is promising for rapid radioanalytical separations.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

Sizing of discontinuous natural fibers: Effect of sizing approach and sizing concentration on composite properties

Natural fiber reinforced composites (NFRCs) are gaining attention in automotive applications as an alternative to glass fiber composites due to their lightweight and renewable sourcing. However, the inherent hydrophilicity of natural fibers leads to poor compatibility with hydrophobic polymers which adversely affects the mechanical properties of the composites and can limit their application to non-structural parts. Sizing is a common approach used for synthetic fibers to improve the interface between fiber and matrix. However, there is limited study on the sizing of natural fibers, and hence the focus of this work. Here, in this study, two different approaches to sizing discontinuous coir fibers were investigated, namely; (1) ex-situ sizing and (2) in-situ sizing. A commercial polypropylene (PP) based sizing agent was used and the effects of varying sizing solution concentrations (1.5, 2.5, and 3.5 wt%) on the properties of the composites was studied. Results showed that composites prepared via the in-situ sizing process had better fiber–matrix adhesion and improved tensile properties compared to ex-situ sized composites. On studying the effect of different sizing concentrations on composite properties, we found that the tensile strength of the composites increased (by ∼ 42 %) up to 2.5 wt% sizing concentration (in solution) and then decreased. However, the impact strength decreased significantly on increasing the sizing content beyond 1.5 wt% (by ∼ 40 %). Additionally, the study was further extended to investigate the effect of sizing on different NFRCs (coir, banana, and cottonized hemp fiber) where effectiveness of sizing was found to be influenced by the fiber surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effects of cleavable comonomer structure and crosslinker chemistry on the performance and deconstructability of frontally cured pDCPD composites

Reclaiming undamaged carbon fiber from thermoset composites requires chemical recycling methods that leverage complete deconstruction of the polymer matrix. Cleavable comonomers enable chemical recycling of poly(dicyclopentadiene) (pDCPD) composites, but current systems suffer from reduced glass transition temperature (T g ), limiting application. Here, we investigate the effect of cleavable comonomer loading and cleavable crosslinker chemistry on network formation, thermomechanical properties, and fiber recovery in frontally cured pDCPD composites. All formulations fully deconstructed in acid and recovered fibers ranged from pristine to variably contaminated depending on crosslinker chemistry. Reducing backbone-cleaving comonomer content and introducing cleavable crosslinkers raised composite T g to 126–138 °C compared to 105 °C previously reported in deconstructable pDCPD composites. Although the cleavable crosslinkers increased T g in unreinforced polymers to 150–160 °C, the fiber-reinforced composite T g remained lower due to under-curing and interactions between the crosslinkers and the fiber surface. Increasing polymerization initiator loading improved comonomer conversion and yielded a deconstructable composite with T g = 151 °C, approaching the performance of non-deconstructable pDCPD composites (T g = 161 °C). This work clarifies how cleavable comonomer and crosslinker chemistry governs curing, thermomechanical performance, and reclaimed reinforcement quality, and the results highlight the need for more robust cleavable comonomers to realize multigenerational composite materials without sacrificing thermomechanical performance.

Carbon fibers↗
DOE OSTI2025

Hierarchically Structured Vitrimer Biocomposites for Sustainable Manufacturing

Polymers containing dynamic covalent bonds (DCBs) exhibit thermoplastic-like flow above their topology freezing temperature (T v ) while maintaining thermoset-like properties below it, making them promising for sustainable manufacturing. However, their large-scale adoption remains limited due to challenges in accurately determining T v and achieving efficient fiber-matrix bonding in composite applications. Here, hierarchically structured epoxy-anhydride-based polyester vitrimer composites reinforced with cellulosic filaments is demonstrated, where hydroxyl groups on fiber surfaces participate directly in transesterification with the matrix. Further, this dynamic interfacial bonding delivers exceptional mechanical properties, including ≈70 MPa shear strength and >10% strain-to-failure, while enabling thermal malleability. Using a combination of nuclear magnetic resonance and nano-infrared spectroscopies, direct evidence is provided that chemical bond exchange begins well below the conventionally measured T v , supporting the hypothesis that rheologically determined T v reflects a combination of chemical exchange and frictional dynamics rather than a discrete transition. The composites demonstrate excellent processability through vacuum-assisted resin transfer molding and maintain >90% of their mechanical properties after multiple thermal reforming cycles. These findings advance both the fundamental understanding of vitrimeric transitions and the practical development of sustainable, high-performance composite materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Thermokinetic mixing compounding for polymer composites – a comprehensive review

High-speed thermokinetic mixers (K-mixers) represent an advanced compounding technology that employs intense shear and friction to convert kinetic energy directly into thermal energy. This mechanism enables rapid mixing cycles, often under one minute, facilitating exceptional filler dispersion while minimizing the material’s thermal history. This is particularly effective for compounding challenging materials, including heat-sensitive biopolymers, wet filler feedstocks, and nanofillers prone to agglomeration. As the first comprehensive review of this technology, this article synthesizes the fundamental principles of thermokinetic mixing (K-mixing) and surveys recent advances in polymer composite fabrication. We contrast the working principles of K-mixers with conventional twin-screw extrusion, highlighting distinct advantages in dispersing nanoscale fillers, exfoliating layered materials, and processing wet cellulosic feedstocks and ultra-high filler loadings (e.g., 85 wt%). Furthermore, strategies to optimize filler–matrix interfacial bonding under rapid-processing constraints, such as the kinetic selection of compatibilizers and fiber surface treatments, are evaluated. Finally, we analyze key structure-processing-property relationships and outline future directions in scaling up, reactive processing, and hybrid material development.

Zhang, Xuefeng [University of Maine]↗