Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dust particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Self‐consistent transport simulation of boron dust particle injection in the peripheral plasma in Large Helical Device

Abstract The trajectories and the ablation positions of boron dust particles dropped from an impurity powder dropper in the peripheral plasma in the Large Helical Device (LHD) were calculated using a three‐dimensional edge plasma simulation code (EMC3‐EIRENE) and a dust transport simulation code (DUSTT). The simulation shows that the trajectory of the boron dust particles is deflected at the upper divertor leg due to the effect of the hydrogen plasma flow, and the ablation positions of the dust particles in an ergodic layer change toward the outboard side of the torus for higher plasma densities. The effect of the boron ion flow in the divertor leg on the deflection is investigated by coupling the two codes self‐consistently. The simulation predicts that the boron ions in the divertor leg, which are produced by sputtering on the divertor plates, which do not affect the change in the ablation positions. It also shows that the ablation positions move toward the inboard side and approach the Last Closed Flux Surface (LCFS) in case of increased boron dust drop rates, which is caused by the lowered plasma flow in the upper divertor leg due to the lowered electron temperature by radiation cooling by the dropped dust particles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Controlling the charge of dust particles in a plasma afterglow by timed switching of an electrode voltage

Abstract A method is demonstrated for controlling the charge of a dust particle in a plasma afterglow, allowing a wider range of outcomes than an earlier method. As in the earlier method, the dust particles are located near an electrode that has a DC voltage during the afterglow. Here, that DC voltage is switched to a positive value at a specified delay time, instead of maintaining a constant negative voltage as in the earlier method. Adjusting the timing of this switching allows one to control the residual charge gradually over a wide range that includes both negative and positive values of charge. For comparison, only positive residual charges were attained in the earlier method. We were able to adjust the residual charge from about −2000 e to +10 000 e , for our experimental parameters (8.35 µ m particles, 8 mTorr argon pressure, and a DC voltage that was switched from −150 V to +125 V within the first two milliseconds of the afterglow). The plasma conditions near the dust particles changed from ion-rich to electron-rich, when the electrode was switched from cathodic to anodic. Making this change at a specified time, as the electrons and ions decay in the afterglow, provides this control capability. These results also give insight into the time development of a dust particle’s charge in the afterglow, on a sub-millisecond time scale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Hyperdiffusion of dust particles in a turbulent tokamak plasma

The effect of plasma turbulence on the trajectories of dust particles is investigated for the first time. The dynamics of dust particles is computed using the ad-hoc developed Dust Injection Simulator code, using a 3D turbulent plasma background computed with the TOKAM3X code. As a result, the evolution of the particle trajectories is governed by the ion drag force, and the shape of the trajectory is set by the Stokes number $St\propto a_d/n_0$, with $a_d$ the dust radius and $n_0$ the density at the separatrix. The plasma turbulence is observed to scatter the dust particles, exhibiting a hyperdiffusive regime in all cases. The amplitude of the turbulent spread of the trajectories $\Delta r^2$ is shown to depend on the ratio $Ku/St$, with $Ku\propto u_{rms}$ the Kubo number and $u_{rms}$ the fluctuation level of the plasma flow. These results are compared with a simple analytical model, predicting $\Delta r^2\propto (Ku/St)^2t^3$, or $\Delta r^2\propto (u_{rms}n_0/a_d)^2t^3$. As the dust is heated by the plasma fluxes, thermionic emission sets the dust charge, originally negative, to slightly positive values. This results in a substantial reduction of the ion drag force through the suppression of its Coulomb scattering component. The dust grain inertia is then no longer negligible, and drives the transition from a hyperdiffusive regime towards a ballistic one.

dust↗
DOE OSTI2021

Hyperdiffusion of dust particles in a turbulent tokamak plasma

In this work, the effect of plasma turbulence on the trajectories of dust particles is investigated for the first time. The dynamics of dust particles is computed using the ad hoc developed Dust Injection Simulator code, using a 3D turbulent plasma background computed with the TOKAM3X code. As a result, the evolution of the particle trajectories is governed by the ion drag force, and the shape of the trajectory is set by the Stokes number St∝a d /n 0 , with a d the dust radius and n 0 the density at the separatrix. The plasma turbulence is observed to scatter the dust particles, exhibiting a hyperdiffusive regime in all cases. The amplitude of the turbulent spread of the trajectories Δr 2 is shown to depend on the ratio Ku/St, with Ku∝u rms the Kubo number and urms the fluctuation level of the plasma flow. These results are compared with a simple analytical model, predicting Δr 2 ∝(Ku/St) 2 t 3 , or Δr 2 ∝(u rms n 0 /a d ) 2 t 3 . As the dust is heated by the plasma fluxes, thermionic emission sets the dust charge, originally negative, to slightly positive values. This results in a substantial reduction of the ion drag force through the suppression of its Coulomb scattering component. The dust grain inertia is then no longer negligible and drives the transition from a hyperdiffusive regime toward a ballistic one.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulations of the collection of mesospheric dust particles with a rocket instrument

We investigate the collection of dust particles in the mesosphere with the MESS (MEteoric Smoke Sampler) instrument that is designed to fly on a sounding rocket. We assume that the ice particles that form in the polar mesosphere between 80 and 85 km altitude in summer contain meteoric smoke particles; and these should be collected with MESS. The instrument consists of a collection device with an opening and closure mechanism, as well as an attached conic funnel which increases the sampling area in comparison to the collection area. Dust particles are collected either directly after passing through the instrument or indirectly after colliding with and fragmenting on the funnel wall. We calculate the dust and fragment trajectories in the detector to determine the collection efficiency for different particle sizes, rocket velocities, and heights, and we find the final velocities and the temperatures of the particles. The considered design has a sampling area of 62.78 mm diameter and a collection area of 20 mm diameter. For the conditions at the rocket launch site in Andøya, Norway, we estimate the collection of meteoric smoke particles contained in the ice particles to be ~10 12 –10 14 amu mm –2 . The estimated temperatures suggest that the composition of these smoke particles is not affected by the collection. Our calculations also show that keeping the instrument open above 85 km altitude increases the amount of small smoke particles that are directly collected. The directly collected smoke particles are heated as they decelerate, which can affect their composition.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Controlling the charge of dust particles in an afterglow by modulating the plasma power

Abstract A dust particle immersed in a glow-discharge plasma has long been known to have a charge that is negative , while the plasma is powered. However, in the afterglow, following the stopping of the plasma power, a large positive charge can collect on the particle, as was shown recently for particles in a cathodic sheath. While that outcome of positive charging in the afterglow may be common, an experimental discovery reported here reveals that the opposite outcome is also possible: a particle can develop a negative charge in the afterglow, if the plasma had previously been operated with a modulated power. Before stopping the plasma power off altogether, in a run with power modulated at a low duty cycle of 4.5 % , the particle’s residual charge was negative, but it was positive in a control run without modulation. This result points to a way of controlling the charge of dust particles in a decaying plasma, which can be useful for mitigating defects in semiconductor manufacturing.

Physics↗
DOE OSTI2020

Dynamics of dust particles confined in imposed potential structures in strongly magnetized, low-temperature plasmas

A new phenomenon called imposed ordered structures has been of particular interest to the dusty plasma community within the past several years. These structures are a new type of pattern formation within a dusty plasma in which the dust particles become fixed to a background confining potential whose spatial structure is determined by some conducting element present in the plasma. In previous works, this element has typically been a conducting wire mesh. One of the unanswered questions is whether the dust particles become trapped beneath the conducting surface of the mesh or in the gaps (holes) between the wires. This work makes use of a new electrode whose shape is designed to mimic that of wire mesh, but with much larger dimensions to facilitate in situ diagnostic measurements. Observations of the dust show that particles become confined to the regions beneath the holes of this new electrode. Measurements of the dust particle velocities allow for a determination of the kinetic energy within the dust cloud which show that the particles are in an energetic steady state. Further, comparisons of spatial profiles of the particle velocities also show that the dust particles typically reside in areas of increased plasma glow, possibly being trapped by plasma filaments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Long-lasting strong electrostatic attraction and adhesion forces of dust particles on photovoltaic modules

Photovoltaic (PV) energy-yield loss due to solar module soiling has become increasingly important as solar module deployment is now at the hundreds of gigawatts scale and continues to grow rapidly. The electrostatic attraction and adhesion force (F es ) of dust particles by the high voltages from solar panels have been reported to be 1 to 2 orders of magnitude stronger than the van der Waals and water capillary forces, which has been corroborated by observing the increase in system voltage-induced soiling rate by setting up an outdoor test. Here, we report another characteristic of F es on soiling - long-lasting or slow decay after turning off the high voltage applied to solar panels. The F es decay time varies across a wide time range of 1 to 10 h, depending on two factors: 1) whether the cell, the particle, or both were charged with high voltage before the voltages were turned off; and 2) how the cell was connected to the ground after the voltage was turned off - either connected through the power-supply electronics, directly connected to the ground, or electrically floated. The Fes decay is understood in terms of 1) net electrical charge dissipations in both particle and cell, 2) thermal disordering of dipole polarization in the module glass dielectrics, and 3) charge redistribution by the electrostatic interaction of particle and module glass. This long-lasting F es for hours can affect the solar panel soiling after sunset, and it can have an even greater effect when combined with water condensation at night.

14 SOLAR ENERGY↗
DOE OSTI2020

Decay of Electrostatic Force of Dust Particles on Photovoltaic Modules

Photovoltaic (PV) energy yield loss due to solar module soiling has become increasingly important as solar module deployment is now at the hundreds of gigawatts scale and continues to grow rapidly. We have reported on direct measurements-using atomic force microscopy (AFM)-of strong electric-field-induced attraction and adhesion force (Fes) of dust particles onto solar panel that are 1 to 2 orders of magnitude stronger than the van der Waals and water capillary forces, corroborated by observing the increase in system voltage-induced soiling rate. Here, we report another characteristic of Fes on soiling-long lasting or slow decay after turning off the high voltage applied to solar panels. The Fes decay time varies in a wide time range of 1 to 10 hours, depending on two factors: 1) either/both the cell or/and particle were charged with high voltage before the voltages were turned off; and 2) how the cell was connected to the ground after the voltage was turned off-either connected through the power supply electronics, directly connected to the ground, or electrically floated. The Fes decay is understood in terms of 1) net electrical charge dissipations in both particle and cell, 2) thermal disordering of dipole polarization in the module glass dielectrics, and 3) charge redistribution by the electrostatic interaction of particle and module glass. This long-lasting Fes for hours can significantly affect the solar panel soiling after sunset, especially combined with water condensation.

14 SOLAR ENERGY↗
DOE OSTI2023

Mitigating dust particle contamination in an afterglow plasma by controlled lifting with a DC electric field

Abstract Particle contamination due to plasma processing motivates the design of a method of electrically lifting particles in a time interval after a plasma’s power is turned off. Small solid dust particles have electric charges that are not frozen until a late stage of the plasma afterglow. Beyond that time, before they fall to a surface below and cause defects, particles can be lifted in a controlled manner by applying an appropriate direct-current (DC) electric field, as we demonstrate experimentally. A few milliseconds after an argon plasma’s capacitively coupled radio-frequency power is switched off, a vertical DC electric field is applied. Thereafter, video imaging shows that the falling of the particles is slowed or stopped altogether, depending on the magnitude of the upward electric force.

Physics↗
DOE OSTI2021

Search for meteoritic GEMS II: Comparison of inclusions in amorphous silicates from the Paris chondrite and from anhydrous chondritic interplanetary dust particles

Amorphous silicates containing abundant nano-inclusions have been reported in the Paris CM chondrite (Leroux et al., 2015). They have chemical and morphological similarities to glass with embedded metal and sulfides (GEMS) found in interplanetary dust particles (IDPs) and micrometeorites believed to originate from comets. We used scanning transmission electron microscopy (STEM) with energy-dispersive X-ray spectroscopy (EDS) and nanodiffraction to study the chemistry and mineralogy of these inclusions in order to understand the origin of the GEMS-like material in Paris and its possible relationships to other materials found in primitive chondritic materials including IDP GEMS. EDS and diffraction analyses indicate compositional and mineralogical differences between the nanophase inclusions in cometary GEMS and Paris GEMS-like material. Metal inclusions are notably absent within Paris amorphous silicate. Ni-rich sulfides, including pentlandite, are common in even the least altered matrix material of Paris, while they are absent in GEMS-bearing IDPs and Ultracarbonaceous Antarctic Micrometeorites (UCAMMs). From examination of the inclusions, we cannot yet confirm or refute the possibility that GEMS-like material in Paris is related to cometary GEMS. The distinct compositions and mineralogy of the Paris material may be due to aqueous alteration of cometary GEMS precursors, but they may also denote an independent origin for meteoritic GEMS-like assemblages.

58 GEOSCIENCES↗
DOE OSTI2021

LBT Reveals Large Dust Particles and a High Mass-loss Rate for K2-22 b

The disintegrating planet candidate K2-22 b shows periodic and stochastic transits best explained by an escaping debris cloud. However, the mechanism that creates the debris cloud is unknown. The grain size of the debris as well as its sublimation rate can be helpful in understanding the environment that disintegrates the planet. Here, we present simultaneous photometry with the g band at 0.48 μm and K {sub S} band at 2.1 μm using the Large Binocular Telescope. During an event with very low dust activity, we put a new upper limit on the size of the planet of 0.71 R {sub ⊕} or 4500 km. We also detected a medium depth transit that can be used to constrain the dust particle sizes. We find that the median particle size must be larger than about 0.5–1.0 μm, depending on the composition of the debris. This leads to a high mass-loss rate of about 3 × 10{sup 8} kg s{sup −1}, which is consistent with hydrodynamic escape models. If they are produced by some alternate mechanism such as explosive volcanism, it would require extraordinary geological activity. Combining our upper limits on the planet size with the high mass-loss rate, we find a lifetime of the planet of less than 370 Myr. This drops to just 21 Myr when adopting the 0.02 M {sub ⊕} mass predicted from hydrodynamical models.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Measurement report: A comparative analysis of an intensive incursion of fluorescing African dust particles over Puerto Rico and another over Spain

Measurements during episodes of African dust, made with two wideband integrated bioaerosol spectrometers (WIBSs), one on the northeastern coast of Puerto Rico and the other in the city of León, Spain, show unmistakable, bioaerosol-like fluorescing aerosol particles (FAPs) that can be associated with these dust episodes. The Puerto Rico event occurred during a major incursion of African dust during June 2020. The León event occurred in the late winter and spring of 2022, when widespread, elevated layers of dust inundated the Iberian Peninsula. Satellite and back-trajectory analyses confirm that dust from northern Africa was the source of the particles during both events. The WIBSs measure the size of individual particles in the range from 0.5 to 30 µm, derive a shape factor, and classify seven types of fluorescence from the FAPs. In general, it is not possible to directly determine the specific biological identity from fluorescence signatures; however, measurements of these types of bioaerosols in laboratory studies allow us to compare ambient fluorescence patterns with whole microbial cells measured under controlled conditions. Here we introduce some new metrics that offer a more quantitative approach for comparing FAP characteristics derived from particles measured under different environmental conditions. The analysis highlights the similarities and differences at the two locations and reveals differences that can be attributed to the age and history of the dust plumes, e.g., the amount of time that the air masses were in the mixed layer and the frequency of precipitation along the air mass trajectory.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

A glimpse of stars the size of dust particles

The Nuclear Imaging System (NIS) is an important diagnostic tool used to study nuclear fusion implosions at a research facility in California. There a capsule the size of a flea is compressed until it reaches the size of a speck of dust. As the capsule collapses on itself and ignites under extreme temperature and pressure, NIS detects particles emitted from that process at a scale that would correspond to watching a 32-inch TV screen from 100 miles away. My work involves taking snapshots of one of the most minuscule, fleeting and amazing experiments on Earth in order to ensure the safety and reliability of the US nuclear stockpile and get closer to developing a new form of clean energy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Modelling dust transport in DIII-D with DTOKS-Upgrade

Comprehensive upgrades to the dust transport code Dust in TOKamaks (DTOKS) that extend the plasma-dust interaction model are presented and compared with recent measurements of dust transport in DIII-D. Simulations incorporating variation in physical properties of graphite dust with temperature and size in a stationary plasma background suggest a substantial decrease in lifetimes due principally to thermal expansion. The trajectories of 53 dust grains identified from analysis of visible camera data taken across two similar shots were used to measure the dust particle velocity distributions. Dust tracks terminated mostly at the outer divertor strike point having a mean observation time of 2.1 ± 0.4 ms. Stochastic modelling of 200 graphite dust particles in the DIII-D tokamak performed with DTOKS-U using plasma simulations generated by OEDGE found similar behaviour, with particles ablating rapidly after acquiring a positive charge in the region close to the outer strike point, creating an acute source of neutral carbon atoms. The simulated mean lifetime, 11 ± 2 ms, showed approximate agreement with experimental observation when corrected by accounting for dust visibility and ignoring the longest trajectories 1.5 ± 0.2 ms. Synthetic diagnostic data generated from coupling the results of DTOKS-U with the visualisation software Calcam offers a powerful new tool for validation of simulations and predictive calculations of dust dynamics.

Physics↗
DOE OSTI2021

Particle charge distributions in the effluent of a flow-through atmospheric pressure low temperature plasma

Atmospheric pressure low-temperature plasmas are often utilized to perform particle synthesis, treatment, and removal. It is well-known that dust particles are highly negatively charged in these plasmas; however, little is known about dust particle charging behavior as particles leave the plasma volume and pass through the spatial afterglow region. In this work, monodisperse particles of various sizes and work functions were introduced into an atmospheric pressure radiofrequency capacitively coupled flow-through plasma. Dust particle electrical mobility distributions downstream of the flow-through plasma were measured utilizing a differential mobility analyzer in conjunction with a condensation particle counter at various gas flow velocities. Charge distributions were determined from the measured electrical mobility distributions. Experiments confirm that particles become less negatively charged, and even net-positively charged after leaving the plasma volume, with a distribution that follows a shifted Boltzmann charge distribution. Additionally, particle charge in the effluent of the flow-through plasma is negligibly dependent on work function but highly size and flow velocity dependent. Larger particles were shown to have a higher magnitude of charge under all studied conditions; however, particle polarity was switchable by varying gas flow velocity. The charging dynamics were simulated utilizing a constant number Monte Carlo model that accounts for electron temperature decay and the transition from ambipolar to free diffusion of electrons and ions in the spatial afterglow. Simulation results also suggest that, at the same flow velocity, larger particles obtain a greater magnitude of charge, negative or positive. Furthermore, the decrease in electron mobility and the difference between ion and electron convective loss rates create an ion-rich region in the plasma effluent that promotes ion–particle collisions and drives particle charge removal and even reversal of polarity. Larger particles more favorably collide with energetic species in these environments, which results in higher charge states.

atmospheric pressure low temperature plasma↗