Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dry heat”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Dry heat sterilization as a method to recycle N95 respirator masks: The importance of fit

In times of crisis, including the current COVID-19 pandemic, the supply chain of filtering facepiece respirators, such as N95 respirators, are disrupted. To combat shortages of N95 respirators, many institutions were forced to decontaminate and reuse respirators. While several reports have evaluated the impact on filtration as a measurement of preservation of respirator function after decontamination, the equally important fact of maintaining proper fit to the users’ face has been understudied. In the current study, we demonstrate the complete inactivation of SARS-CoV-2 and preservation of fit test performance of N95 respirators following treatment with dry heat. We apply scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS), X-ray diffraction (XRD) measurements, Raman spectroscopy, and contact angle measurements to analyze filter material changes as a consequence of different decontamination treatments. We further compared the integrity of the respirator after autoclaving versus dry heat treatment via quantitative fit testing and found that autoclaving, but not dry heat, causes the fit of the respirator onto the users face to fail, thereby rendering the decontaminated respirator unusable. Our findings highlight the importance to account for both efficacy of disinfection and mask fit when reprocessing respirators to for clinical redeployment.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

A conformal heat-drying direct ink writing 3D printing for high-performance lithium-ion batteries

High areal capacity electrodes hold great potential for high-energy density lithium-ion batteries (LIBs), but their poor electrochemical kinetics limit their power density. Here, in this study, high areal capacity 3D-structured LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathodes (4.3 mAh cm -2 ) are prepared via 3D printing with a manner of direct ink writing. The electrodes had an enlarged electrode–electrolyte contact area, shortened diffusion pathway, and reduced intercalation-induced stress, thereby delivering enhanced rate capability and cyclability in LIBs, which is 143.6 mAh g -1 at 3C and a 60.2 % capacity retention over 800 cycles at 1C. Moreover, at electrode level, the 3D-NMC exhibits an energy and power densities of 313.1 Wh kg -1 and 657.9 W kg -1 , respectively. Furthermore, the theoretical calculation suggests that reducing the gap width will be highly beneficial to the energy and power densities. This work establishes a milestone in understanding the cycling effect on the electrode local structure, including the void area and the LiNi 0.8 Mn 0.1 Co 0.1 O 2 region, which confirms the effectiveness of 3D printing for electrode preparation.

25 ENERGY STORAGE↗
DOE OSTI2021

The Role of Water on the Interfacial Adhesion in Si Solar Modules

Delamination of solar module interfaces often occurs in field-tested solar modules after decades of service due to environmental stressors such as humidity. As water diffuses into the module, failure mechanisms like corrosion and delamination are significantly affected. In the presence of water, the interfaces between EVA and the cell, glass, and backsheet all experience losses of adhesion exposing the module to accelerated degradation. Understanding the relation between interfacial adhesion and water content inside PV modules can help mitigate detrimental power losses. Water content measurements via short wave infrared reflectometry combined with 180 degrees peel tests were used to study and quantify the effect of water ingress and egress on adhesion. Changes in adhesion strength for different module interfaces are quantified, correlating spatial distribution of water content to adhesion for damp heat and dry heat exposed samples. After 1000 hours of damp heat exposure, decreases in adhesion strength of approximately 1 N/mm were noted for all interfaces.

adhesion↗
DOE OSTI2022

New Evidence for the Importance of Non-Stomatal Pathways in Ozone Deposition During Extreme Heat and Dry Anomalies

Dry deposition could partially explain the observed response in ambient ozone to extreme hot and dry episodes. We examine the response of ozone deposition to heat and dry anomalies using three long-term co-located ecosystem-scale carbon dioxide, water vapor and ozone flux measurement records. We find that, as expected, canopy stomatal conductance generally decreases during days with dry air or soil. However, during hot days, concurrent increases in non-stomatal conductance are inferred at all three sites, which may be related to several temperature-sensitive processes not represented in the current generation of big-leaf models. This may offset the reduction in stomatal conductance, leading to smaller net reduction, or even net increase, in total deposition velocity. We find the response of deposition velocity to soil dryness may be related to its impact on photosynthetic activity, though considerable variability exists. Our findings emphasize the need for better understanding and representation of non-stomatal ozone deposition.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Pre-combustion mercury removal with co-production of hydrogen via coal electrolysis

Here, pre-combustion mercury removal via coal electrolysis was performed and investigated on a bench-scale coal electrolytic cell (CEC) systemically, and factorial design was used to determine the effect of different operating conditions (coal particle size, operating temperature, operating cell voltage, and flow rate of slurry) on the percentage of mercury removal, percentage of ash removal, and dry heating value change. The results showed that the operating cell voltage, as well as the interaction between operating cell voltage and coal particle size, are significant factors in the percentage of mercury removal. There is no significant factor in the percentage of ash removal and the dry heating value change, but the coal could be purified while keeping the dry heating value almost constant after electrolysis. A co-product of hydrogen could be produced during coal electrolysis with 50% lower energy consumption compared with water electrolysis. Meanwhile, a mechanism for mercury removal in coal was proposed. The facts indicate that coal electrolysis is a promising method for pre-combustion mercury removal.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Intensified Humid Heat Events Under Global Warming

Based on the CMIP5 multi-model simulations, this paper investigates the future changes in extreme wet-bulb temperatures (TWs) and extreme dry-bulb temperatures (Ts) globally under both low and high emission scenarios (RCP4.5 and RCP8.5). Under a warming climate, T and TW exhibit a higher absolute increase in their mean values over the mid-high latitudes while they show higher relative increases in their mean values and variability over tropics. Here, humid and dry heat events which consist of consecutive extreme TWs and Ts show higher occurrences over tropics, governed by the joint increases in mean values and variability of TW and T therein. Humid heat events show intensifications to dry heat events with higher frequency, duration, and intensity, driven by the lower variability of TW than T. In the mid-high latitudes, heat events will start earlier and last longer in warm season under RCP8.5 than RCP4.5, motivating the need for global warming mitigation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Carnot Analysis of Heat Pump Drying: Ideal Efficiency and Dry Time

Drying processes are important in appliances and in industry, and clothes drying accounts for approximately 3% of residential primary energy consumption in the US. Globally, heat pump tumble dryers (HPD) are increasing their market share against the ubiquitous electric resistance tumble dryer (ERD). In this work, efficiency and dry time limits are defined for ideal HPDs, for both closed air cycle (unvented) and open air cycle (vented). These limits are compared with the limits for ERD. The traditional Carnot efficiency limit for an ideal heat pump, operating between a hot and a cold thermal reservoir, does not apply directly to clothes dryers. One reason dryers require a novel analysis is the presence of additional degrees of freedom, since the hot and cold temperatures are floating, unfixed by ambient conditions. Furthermore, dryers can operate in a closed or open air cycle, and each requires a different analysis. In the closed (unvented) case, the hot and cold temperatures are coupled to each other; while in the open (vented) case, the hot and cold temperatures are both independent free variables. This paper provides an analysis of the fundamental efficiency limits of ERDs and HPDs, which can inform the design and performance limits of evaporative drying technology.

Gluesenkamp, Kyle↗
DOE OSTI2020

Ambient Mass Spectrometry Rapid Analysis Methods for Trace Inorganics

The ability to rapidly detect and characterize the chemistry of trace quantities of inorganic species has multiple potential applications, including nuclear safeguards, nuclear forensics, and environmental monitoring. Some mass spectrometric methods currently exist, but they are costly and time-intensive, often destroying chemical information in the process of ionization. Ambient mass spectrometry is a relatively new analytical method in which samples are introduced to the mass spectrometer from atmospheric pressure, rather than from high vacuum. Ambient MS can operate with gentler ionization methods such as electrospray ionization (ESI) and paper-spray ionization (PSI), reducing fragmentation and preserving the chemical information of the analyte. This may be useful for determining the intended purpose of material in a sample. Strontium, part of nuclear fallout, is analyzed here to test these new analytical methods for viability. Electrospray ionization mass spectrometry functions by spraying the sample as a solution through a needle charged to a few kV. A nebulizing gas flows out along with the sample to create the spray before droplets enter a drying chamber with heated drying gas to remove the solvent molecules. From there bare analyte ions enter the mass spectrometer. This method has the advantage of relatively fast sample preparation and stable ionization. More stable ionization produces higher-quality data. Paper-spray ionization mass spectrometry operates by applying sample to a paper triangle. The paper triangle is then electrified in a metal clamp to a few kV before spray solvent is applied. The spray solvent transports analyte in the sample to the tip, where it is ionized and enters the mass spectrometer. One advantage of this method is reduced sample preparation - an analyst can even swipe a surface and cut a triangle directly from the swipe. The data analysis serves to rapidly process tens of samples all at once. The mass spectrometer outputs a file containing a few hundred spectra for each sample. The pipeline processes each one to identify peaks of interest. A full palette of data analysis metrics are generated, including plots of the raw data and plots of calculated values such as isotopic ratios. The pipeline filters the raw data to remove noise and background peaks, as well as peaks representing detector saturation. A heat map is generated to show the overall spectrum in mass-time- intensity space. Post-processing, we obtained the desired calibration curves, demonstrating that both ESI-MS and PSI-MS are viable methods for quantifying trace amounts of inorganics while retaining their chemical speciation information. ESI-MS demonstrated a linear response region of 100 ppb to 20 ppm, with a limit-of-detection of around 100 ppb. At top left is an example spectrum with the {sup 88}SrNO{sub 3} peak identified to show the retention of chemical speciation. PSI-MS showed a linear response region of around 1 ppb to 1 ppm, with a limit-of-detection of near 1 ppb. PSI-MS produced more erratic results than ESI-MS, likely due to the variability in ionization resulting from manual positioning of the paper triangle near the MS inlet. Future efforts will focus on improving the repeatability of PSI-MS as well as analyzing other species of interest such as cerium and uranium. Improvements will also be made to create more reliable data extraction and intelligent data filtering.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Quantifying the impacts of compound extremes on agriculture

Agricultural production and food prices are affected by hydroclimatic extremes. There has been a growing amount of literature measuring the impacts of individual extreme events (heat stress or water stress) on agricultural and human systems. Yet, we lack a comprehensive understanding of the significance and the magnitude of the impacts of compound extremes. This study combines a fine-scale weather product with outputs of a hydrological model to construct functional metrics of individual and compound hydroclimatic extremes for agriculture. Then, a yield response function is estimated with individual and compound metrics, focusing on corn in the United States during the 1981–2015 period. Supported by statistical evidence, the findings suggest that metrics of compound hydroclimatic extremes are better predictors of corn yield variations than metrics of individual extremes. The results also confirm that wet heat is more damaging than dry heat for corn. This study shows the average yield damage from heat stress has been up to four times more severe when combined with water stress.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Quantitative form and fit of N95 filtering facepiece respirators are retained after dry and humid heat treatments for coronavirus deactivation

Re-use of filtering facepiece respirators (FFRs, commonly referred to as N95s) normally meant for single use only is becoming common in healthcare facilities due to shortages caused by the COVID19 pandemic. Here we report that mouse hepatitis virus (MHV) initially seeded on FFR filter material is inactivated (6 log reduction as measured by 50% tissue culture infective dose (TCID50)) after dry heating at 75 °C for 30 minutes. We also find that the quantitative fit of FFRs after heat treatment at this temperature, under dry conditions or at 90% relative humidity, is not affected by single or ten heating cycles. Previous studies have reported that the filtration efficiency of FFR filters is not negatively impacted by these heating conditions. These results suggest that thermal inactivation of coronaviruses is a potentially rapid and widely deployable method to re-use N95 FFRs in emergency situations where reusing FFRs is a necessity and broad-spectrum sterilization is unavailable. However, we also found that a heat source that emits radiation (e.g., an exposed heating element) results in rapid qualitative degradation of the FFR. Finally, we discuss differences in the results reported here and other recent studies investing heat as a means to recycle FFRs and suggest that overall wear time and donning/doffing cycles are important factors that need to be considered.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Quantitative Fit Evaluation of N95 Filtering Facepiece Respirators and Coronavirus Inactivation Following Heat Treatment

Abstract Reuse of filtering facepiece respirators (FFRs, commonly referred to as N95s) normally meant for single use has become common in healthcare facilities due to shortages caused by the COVID-19 pandemic. Here, we report that murine hepatitis coronavirus initially seeded on FFR filter material is inactivated (6 order of magnitude reduction as measured by median tissue culture infective dose, TCID50) after dry heating at 75°C for 30 min. We also find that the quantitative fit of FFRs after heat treatment at this temperature, under dry conditions or at 90% relative humidity, is not affected by single or 10 heating cycles. Previous studies have reported that the filtration efficiency of FFRs is not negatively impacted by these heating conditions. These results suggest that thermal inactivation of coronaviruses is a potentially rapid and widely deployable method to reuse N95 FFRs in emergency situations where reusing FFRs is a necessity and broad-spectrum sterilization is unavailable. However, we also observe that a radiative heat source (e.g. an exposed heating element) results in rapid qualitative degradation of the FFR. Finally, we discuss differences in the results reported here and other recent studies investigating heat as a means to recycle FFRs. These differences suggest that while our repeated decontamination cycles do not affect FFR fit, overall wear time and the number of donning/doffing cycles are important factors that likely degrade FFR fit and must be investigated further.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

The Mechanical Response of High Burnup 17x17 PWR Fuel Rods Under Bending

As a part of the US Department of Energy Office of Nuclear Energy High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory has performed 4pt-bend tests on a series of 17x17 PWR fuel rods that were discharged with rod average burnups between 50 and 60 GWd/MTU. The rods include four different kinds of fuel cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. Six rods of each type (combining Zirc-4 and LT Zirc-4 as one type) were tested to failure at room temperature and 200 oC. Three of each type experienced a full-length heat treatment cycle from RT to 400 oC to RT with an 8 hr soak at 400 oC to simulate the expected limiting vacuum drying condition, which potentially induces hydride reorientation and causes some annealing of irradiation damage in the cladding. Overall, the fuel rods show significant capacity to deflect in bending and exhibit non-linear deformation before failing. The calculated failure strains range from 1.5% to 3.8%. The simulated vacuum drying heat treatment had the largest effect on fuel rods with ZIRLO and M5 cladding. In both cases the heat treatment caused increases in the plastic strain at failure, suggesting some annealing of irradiation damage is occurring. The finite element modeling of the 4pt bending test assume the pellet is a collection of pellet wedge pieces. The results for the Zircaloy-4 rods suggest that the pellets are bonded to the cladding and friction controls the relative motion of the pellet wedge pieces.

Cantonwine, Paul↗
DOE OSTI2024

Manufacturing Cathodes via Dry-Processing for Lithium-Ion Batteries

Conventional lithium-ion battery (LIB) electrodes are prepared through a wet slurry process with n-methyl pyrrolidone solvent, especially for cathodes. The wet slurry process encounters several disadvantages such as binder migration, electrode cracking in thick electrodes, energy intense heat-dry NMP solvent removal, and costly NMP recovery. The cost and energy consumption of coating and drying of electrode are about 11.5 % and > 46 % in LIB manufacturing, respectively. Thereby, it is essential to develop a facile roll-to-roll solvent-free LIB electrode processing for reducing the cost and energy consumption. Recently, the Maxwell-type dry processing (DP) shines new lights on LIB manufacturing, which mainly bases on dry mixing (DM) of electrode component powder followed by calendering into electrode films and laminating onto current collectors, realizing the rapid manufacturing of LIB electrodes in a powder-to-film manner for industries. This report shares some recent progress on the DP from our group. We aim to further advance the manufacturing science of DP by correlating the processing conditions with electrode properties and performance. Particularly, we investigate the effect of DM, and compression on the polytetrafluoroethylene (PTFE) binder fiberization, porosity, mechanical properties, electrical conductivity and electrochemical behaviors of electrodes. The DM study suggests that PTFE fiberization heavily relies on the degree of DM. Insufficient DM results in poor PTFE fiberization while outrageous DM damages the formed PTFE fibers. Both negatively affect the mechanical behaviors of the electrodes and their rate capability. However, moderate DM is highly beneficial. In addition, our study of the porosity impact reveals that LiNi0.8Mn0.1Co0.1O2 (NMC) secondary particles can be broken into primary particles due to compression, especially at low porosity. Those fractured NMC secondary particles exhibit lower modulus. We propose that a moderate porosity of around 32% favors the electronic conductivity, charge transfer impedance and rate capability. The study of the cathodic electrolyte interphase layer of PTFE-based DPed electrode confirms that side reactions of PTFE binder due to the formation of LiF in LiClO4-based electrolyte.

Tao, Runming↗
DOE OSTI2020

Evaluation of the DC bus link capacitors and power transistor modules in the qualification testing of PV inverters

To achieve useful, fair, and cost-effective design qualification and type approval testing for PV inverters, two procedures were developed and demonstrated to evaluate the bus link capacitors and power transistor—and where applicable, its module—for long-term reliability. We evaluate the inverter under simulated use conditions with heat run tests to find the highest operating temperatures reached by these components. The procedures are demonstrated in this study with a 4-kVA class string inverter. The maximum temperature of the DC bus link capacitors was determined to be 76.4°C when the ambient temperature was at the inverter's maximum rated temperature of 60°C with derating occurring. On the other hand, the power transistor module's maximum temperature using the heat sink temperature as the index, 92.6°C, occurred in an ambient of 40.8°C when derating was not occurring. The conditions found for upper temperatures exhibited by these components are, respectively, proposed for implementation in the dry heat and thermal cycling tests in the IEC 62093 “Power conversion equipment for photovoltaic systems – Design qualification testing” international standard draft so that the levels applied in the tests are in proportion to those experienced in the field. Finally as a result, fairer evaluation of inverter reliability is realized.

14 SOLAR ENERGY↗
DOE OSTI2022

Thermodynamically consistent versions of approximations used in modelling moist air

Abstract Some existing approaches to modelling the thermodynamics of moist air make approximations that break thermodynamic consistency , such that the resulting thermodynamics does not obey the first and second laws or has other inconsistencies. Recently, an approach to avoid such inconsistency has been suggested: the use of thermodynamic potentials in terms of their natural variables , from which all thermodynamic quantities and relationships (equations of state) are derived. In this article, we develop this approach for unapproximated moist‐air thermodynamics and two widely used approximations: the constant‐ approximation and the dry heat capacities approximation. The (consistent) constant‐ approximation is particularly attractive because it leads to, with the appropriate choice of thermodynamic variable, adiabatic dynamics that depend only on total mass and are independent of the breakdown between water forms. Additionally, a wide variety of material from different sources in the literature on thermodynamics in atmospheric modelling is brought together. It is hoped that this article provides a comprehensive reference for the use of thermodynamic potentials in atmospheric modelling, especially for the three systems considered here.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Improving nanoparticle superlattice stability with deformable polymer gels

The self-assembly of colloidal nanoparticles into ordered superlattices typically uses dynamic interactions to govern particle crystallization, as these non-permanent bonds prevent the formation of kinetically trapped, disordered aggregates. However, while the use of reversible bonding is critical in the formation of highly ordered particle arrangements, dynamic interactions also inherently make the structures more prone to disassembly or disruption when subjected to different environmental stimuli. Thus, there is typically a trade-off between the ability to initially form an ordered colloidal material and the ability of that material to retain its order under different conditions. Here, we present a method for embedding colloidal nanoparticle superlattices into a polymer gel matrix. This encapsulation strategy physically prevents the nanoparticles from dissociating upon heating, drying, or the introduction of chemicals that would normally disrupt the lattice. However, the use of a gel as the embedding medium still permits further modification of the colloidal nanoparticle lattice by introducing stimuli that deform the gel network (as this deformation in turn alters the nanoparticle lattice structure in a predictable manner). Moreover, encapsulation of the lattice within a gel permits further stabilization into fully solid materials by removing the solvent from the gel or by replacing the solvent with a liquid monomer that can be photopolymerized. This embedding method therefore makes it possible to incorporate ordered colloidal arrays into a polymer matrix as either dynamic or static structures, expanding their potential for use in responsive materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Counterflow Virtual Impactor (CVI) Inlet Aboard Aircraft (INLETCVI-AIR) Instrument Handbook

The counterflow virtual impactor (CVI) inlet separates out and samples cloud elements via inertial impaction. Warm, dry, particle-free carrier gas of known composition is pumped to the tip of the inlet in the direction opposite of the flow of air. The flow lines of the incoming free stream air are split. Larger droplets and ice crystals suspended in the sample air have enough inertia to penetrate the counterflow and enter the sample flow, while smaller, unactivated particles follow the streamlines of the air flowing around the inlet’s tip (Noone et al. 1988). The instrument is capable of sampling cloud elements as a function of cut size by changing the velocity of counterflow at the probe tip. The CVI cut size is usually defined as a diameter of a smallest particle for which penetration rate is 50%. For the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facilityGulfstream-159 aircraft’s CVI inlet, that value is usually around 13 microns. The dry heated air, normally used as the carrier gas, also serves to evaporate water from the hydrometeor, leaving the residuals to be sampled by in-cabin aerosol instrumentation. The number concentration of the droplet residue in the CVI sample line is usually increased with respect to corresponding cloud element number concentration. The CVI performance as a concentrator is usually described via CVI enhancement factor, which is a conversion factor between ambient volumetric concentration (not adjusted to standard temperature and pressure) and volumetric concentration in the CVI sample line.

54 ENVIRONMENTAL SCIENCES↗