Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “drop on demand”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

High-throughput mass spectrometry analysis using immediate drop-on-demand technology coupled with an open port sampling interface

Rationale: The sampling throughput of immediate drop-on-demand technology (I.DOT) coupled with an open port sampling interface (OPSI) is limited by software communication. To enable much-needed high-throughput mass spectrometry (MS) analysis capabilities, a novel software was developed that allows for flexible sample selection from a 96-well plate and for maximized analysis throughput using I.DOT/OPSI-MS coupling. Methods: Wells of a 96-well I.DOT plate were filled with propranolol solution and were used to test maximum sampling throughput strategies to minimize analysis time. Demonstration of chemical reaction monitoring was done using acid-catalyzed ring closure of 2,3-diaminonaphthalene (DAN) with nitrite to form 2,3-naphthotriazole (NAT). Analytes were detected in positive electrospray ionization mode using selected reaction monitoring. Results: A maximum throughput of 1.54 s/sample (7.41 min/96-well plate with three technical replicates) was achieved, and it was limited by the peak width of the MS signal resulting in an occasional slight overlap between the peaks. Further, relative standard deviation was 10 ± 1% with all tested sampling strategies. Chemical reaction monitoring of DAN to NAT using nitrite was successfully accomplished with 2 s/sample throughout showing almost complete transformation in 10 min with no signal overlap. Conclusions: This work illustrates the development of a noncontact, automated I.DOT/OPSI-MS system with improved throughput achieved through an optimized software interface. Its achievable analysis time and precision make it a viable approach for drug discovery and in situ reaction monitoring studies.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Rapid Generation of Tandem Mass Spectrometry Reference Libraries Using Immediate Drop-on-Demand Liquid Handling Coupled to an Open Port Sampling Interface

In metabolomics, tandem MS (MS2) fragmentation libraries are important for the identification of unknown features, but generating these libraries takes many valuable hours of instrument and operator time. Here, an immediate droplet-on-demand/open port sampling interface was used to rapidly acquire tandem MS of standards arrayed in a 96-well plate format. A workflow was developed for automated, high-throughput control of MS2 library generation. Pure standard mass spectral libraries were collected on Orbitrap and Q-TOF mass spectrometers for 192 compounds using 6 different collision energies with a throughput of 4 and 7.8 s/spectrum, respectively. Libraries were acquired using different solvent additives, precursor adducts, and ion polarities.

Cahill, John [ORNL] (ORCID:0000000298664010)↗
DOE OSTI2021

An on-demand, drop-on-drop method for studying enzyme catalysis by serial crystallography

Serial femtosecond crystallography has opened up many new opportunities in structural biology. In recent years, several approaches employing light-inducible systems have emerged to enable time-resolved experiments that reveal protein dynamics at high atomic and temporal resolutions. However, very few enzymes are light-dependent, whereas macromolecules requiring ligand diffusion into an active site are ubiquitous. In this work we present a drop-on-drop sample delivery system that enables the study of enzyme-catalyzed reactions in microcrystal slurries. The system delivers ligand solutions in bursts of multiple picoliter-sized drops on top of a larger crystal-containing drop inducing turbulent mixing and transports the mixture to the X-ray interaction region with temporal resolution. We demonstrate mixing using fluorescent dyes, numerical simulations and time-resolved serial femtosecond crystallography, which show rapid ligand diffusion through microdroplets. The drop-on-drop method has the potential to be widely applicable to serial crystallography studies, particularly of enzyme reactions with small molecule substrates.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Multi-level impacts of climate change and supply disruption events on a potato supply chain: An agent-based modeling approach

Context: The world is experiencing frequent extreme weather events like droughts, snowstorms, and shifting of seasons due to climate change. Increased frequency and severity of these extreme weather events threaten food security because agriculture depends on climate conditions. Impacts of climate change on the agricultural system not only occur at the grower’s level, but also cascade to other levels along the supply chain. Objective: In this study, we aim to quantify a wide range of economic impacts of different extreme climate events on different stages of a food supply chain. Methods: We chose the potato supply chain in Idaho as a case study. We developed a multi-echelon supply chain simulation model using an agent-based modeling (ABM) approach with five types of agents—farmers, shippers, processors, retailers, and logistics companies. In addition to the business-as-usual (BAU) scenario, we designed two climate-related disruption events—drought and snowstorm. We quantified the heterogeneous impacts at different stages of the supply chain for both fresh and processed potatoes using key performance indicators (KPIs) including revenues, prices, lead times, traded quantities, and food waste quantity. Results and Conclusion: The impacts of the disruption events are different on different agents in the supply chain for different product categories. The price hike of fresh potatoes is far higher than processed potatoes during disruption events. This price hike makes consumers switch to processed potatoes, which require more fresh potatoes as an input that further reinforces the price hike. However, because processed potatoes have an elastic demand, once their prices go up due to higher input cost, their demand drops. Non-contracted farmers gain additional revenues from the disruption events, whereas contracted farmers incur a loss due to lock-in price and lower than usual harvest. Significance: The methodology developed in this study could be applied to other food and agricultural supply chains for understanding the vulnerabilities at agent levels due to climate change disruption events. Furthermore, the findings would help develop mitigation strategies or policies to improve the well-being of the overall supply chain.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Serial crystallography using automated drop dispensing

Automated, pulsed liquid-phase sample delivery has the potential to greatly improve the efficiency of both sample and photon use at pulsed X-ray facilities. In this work, an automated drop on demand (DOD) system that accelerates sample exchange for serial femtosecond crystallography (SFX) is demonstrated. Four different protein crystal slurries were tested, and this technique is further improved here with an automatic sample-cycling system whose effectiveness was verified by the indexing results. Here, high-throughput SFX screening is shown to be possible at free-electron laser facilities with very low risk of cross contamination and minimal downtime. The development of this technique will significantly reduce sample consumption and enable structure determination of proteins that are difficult to crystallize in large quantities. This work also lays the foundation for automating sample delivery.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Sustainability, Scalability, and Resiliency of the Town of Innisfil Mobility-on-Demand Experiment: Preliminary Results, Analyses, and Lessons Learned

In 2017, the town of Innisfil, Ontario, launched Innisfil Transit in partnership with Uber, a transportation network company, to provide a subsidized on-demand public mobility service as an alternative to investing in a new fixed-route bus service. The performance of Innisfil Transit is documented in a 2021 Ryerson University report by Sweet, Mitra, and Benaroya, which shows greater cost effectiveness of the mobility provided over the proposed bus alternative. This paper expands on those findings by assessing Innisfil Transit with respect to sustainability, scalability, and resiliency. First, we quantify the energy and emissions of this program relative to traditional transit and driving alone across varying powertrains. We then characterize a conservative first-order estimate of the percentage of US communities that fall within a similar spatial-demographic tier as Innisfil. Replicability also hinges on service cost and performance in comparison to average values for low-density transit in the US. Lastly, most transit agencies experienced a significant drop in demand (as much as 90%) with slowly rebounding ridership since the onset of the COVID-19 pandemic. The resiliency of the Innisfil program to the pressures induced by the pandemic is examined in comparison to other transit operations. The lessons learned across these three dimensions complement prior work to better understand the efficiency and sustainability of on-demand public mobility service for low-density communities like Innisfil.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Sustainability, Scalability and Resiliency of the Town of Innisfil Mobility-on-Demand Experiment: Preliminary Results, Analyses, and Lessons Learned: Preprint

In 2017, the Town of Innisfil, Ontario launched Innisfil Transit in partnership with Uber, a transportation network company, to provide a subsidized on-demand public mobility service as an alternative to investing in a new fixed-route bus service. The performance of Innisfil Transit is documented in a 2021 Ryerson University report which shows greater cost effectiveness of the mobility provided over the proposed bus alternative (Sweet, Mitra, and Benaroya 2021). This paper expands on those findings by assessing Innisfil Transit with respect to sustainability, scalability, and resiliency. First, we quantify the energy and emissions of this program relative to traditional transit and driving alone across varying powertrains. We then characterize a conservative first-order estimate of the percentage of US communities that fall within a similar spatial-demographic tier as Innisfil. Replicability also hinges on service cost and performance in comparison to average values for low-density transit in the US. Lastly, most transit agencies experienced a significant drop in demand (as much as 90%) with slowly rebounding ridership since the onset of the COVID-19 pandemic. The resiliency of the Innisfil program to the pressures induced by the pandemic is examined in comparison to other transit operations. The lessons learned across these three dimensions complement prior work to better understand the efficiency and sustainability of on-demand public mobility service for low-density communities like Innisfil.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

On the melt pool dynamic of voxel-controlled metal matrix composites via hybrid additive manufacturing: Laser powder bed fusion and ink-jetting

In this study, the effect of the addition of reinforcement nanoparticles to the 316L matrix by adopting ex-situ and in-situ method (drop on demand jetting) to produce 316L/Al 2 O 3 nanocomposite was investigated. In the ex-situ method, the Al 2 O 3 nanoparticles (NPs) were lightly mixed with 316L powder and processed by laser powder bed fusion. In the in-situ method, an ethanol-based ink containing Al 13 nanoclusters (NCs) was added to 316L powder and then processed by laser. Both ex-situ and in-situ method produced nanocomposites with Al-Si-Mn-O-enriched precipitations within the 316L matrix. The addition of NPs/NCs to the 316L matrix, altered the geometrical characteristic of the single-track melt pools. At the same laser power, with increasing the amount of Al 2 O 3 NPs and Al 13 NCs the melt pool deepened due to reduced thermal conductivity and prolonged liquid presence. Further, as a result, 316L/1 wt% Al 13 NCs deposited single track showed larger grains in comparison to 316L single track. At a high laser power of 150W, the Marangoni flow and the buoyancy force caused the nanoparticles to agglomerate and float to the top surface of tracks; therefore, the wt% fraction of precipitation was drastically reduced due to the loss of Al. The 316L/Al 2 O 3 NPs and 316L/Al 13 NCs exhibited the microhardness of 285 ± 13 HV and 293 ± 7 HV, respectively, higher than the deposited 316L single track, 265 ± 15 HV. Lastly, a hybrid LPBF+ink-jet printer was adopted to selectively change the composition of different zones by adding Al 13 NCs ink to 316L and producing a voxel-controlled metal matrix composite.

316L↗
DOE OSTI2023

Investigation of Reactive Silver Ink Formula for Reduced Silver Consumption in Silicon Heterojunction Metallization

Silver is the most expensive non-silicon component in photovoltaic cells. This is particularly salient for silicon heterojunction (SHJ) cells, which rely on large quantities of low-temperature silver pastes (LT-SP). SHJ cells would benefit greatly from an industrially scalable metallization process that simultaneously offers low silver consumption, low finger resistivities (<20 μΩ·cm), and low processing temperatures. Printed reactive silver inks (RSI) are an innovative candidate to this end. Furthermore, this work furthers the research on RSI metallization by investigating the impact of ink formula on properties pertinent to SHJ cells, including electrical properties, line width, ink splatter, silver consumption, cell performance, and adhesion. We introduce a scalable, high-throughput flexible needle contact printing approach for metallization that solves many of the issues associated with drop-on-demand printing. The printed silver fingers are characterized using electrical measurements and top-down and cross-sectional microscopy. The best performing ink, consisting of silver acetate, ethylamine, and formic acid, achieved silver fingers with total resistivities of 3.1 μΩ·cm and contact resistivities of 3.2 mΩ·cm 2 when printed at 61 °C. This ink metallized a full-sized 156 mm × 156 mm SHJ cell. This is the first reported data for RSI metallization of a full-sized SHJ cell and shows how an optimized RSI can achieve similar performances to LT-SP while consuming 80–90% less silver.

14 SOLAR ENERGY↗
DOE OSTI2023

High-Throughput Characterization and Optimization of Polyamide Hydrolase Activity Using Open Port Sampling Interface Mass Spectrometry

Enzymatic biodegradation of polymers, such as polyamides (PA), has the potential to cost-effectively reduce plastic waste, but enhancements in degradation efficiency are needed. Engineering enzymes through directed evolution is one pathway toward identification of critical domains needed for improving activity. However, screening such enzymatic libraries (100s-to-1000s of samples) is time-consuming. Here we demonstrate the use of robotic autosampler (PAL) and immediate drop on demand technology (I.DOT) liquid handling systems coupled with open-port sampling interface-mass spectrometry (OPSI-MS) to screen for PA6 and PA66 hydrolysis by 6-aminohexanoate-oligomer endo-hydrolase (nylon hydrolase, NylC) in a high-throughput (8–20 s/sample) manner. The OPSI-MS technique required minimal sample preparation and was amenable to 96-well plate formats for automated processing. Enzymatic hydrolysis of PA characteristically produced soluble linear oligomer products that could be identified by OPSI-MS. Incubation temperatures and times were optimized for PA6 (65 °C, 24 h) and PA66 (75 °C, 24 h) over 108 experiments. In addition, the I.DOT/OPSI-MS quantified production of PA6 linear dimer (8.3 ± 1.6 μg/mL) and PA66 linear monomer (13.5 ± 1.5 μg/mL) by NylC with a lower limit of detection of 0.029 and 0.032 μg/mL, respectively. For PA6 and PA66, linear oligomer production corresponded to 0.096 ± 0.018% and 0.204 ± 0.028% conversion of dry pellet mass, respectively. The developed methodology is expected to be utilized to assess enzymatic hydrolysis of engineered enzyme libraries, comprising hundreds to thousands of individual samples.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A 15-Year Retrospective on Immersive Visualization Lessons from the Applied Visualization Laboratory

This article shares the experiences of operating an immersive visualization laboratory over a 15-year period. The paper discusses valuable insights into the lessons learned from various projects, including the challenges they faced, such as technical difficulties, user adoption, and opportunities, and practical solutions for overcoming them. One crucial element for successful immersive visualization projects is interdisciplinary collaboration. The paper presents the advantages of immersive visualization technology, such as improved data comprehension, enhanced communication, and increased engagement in complex scenarios. We present the dynamic realm of virtual and augmented truth (VR/AR) technology in the context of a immersive laboratory system. We spotlight rising trends inside the integration of VR/AR tools for visualization. We also present our experience in dealing with the hardware and software additives in an immersive VR/AR labs, dropping light on the demanding situations and successes encountered throughout everyday operations. Furthermore, it offers practical knowledge and guidance based on years of experience in the field, which can help you overcome challenges and achieve success in your project.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Drought Impacts on Hydroelectric Power Generation in the Western United States

The Western United States experiences large fluctuations in rain and snowfall from year to year, affecting river flows and reservoir levels throughout the region. This interannual variability in water resources leaves a strong signature on total annual energy generated by the region’s fleet of hydroelectric dams. In a wet year, like 2011, hydroelectric power can meet 30 percent of annual western electricity demand. That contribution can drop below 20 percent during severe drought years. Characterizing the contribution of hydroelectric power to the western generation portfolio during drought is crucial to understanding the resilience of the hydropower sector to climate-related risk, both now and in the future. This report analyzes the impacts of historical western droughts on hydroelectric power production by combining two decades’ worth of annual generation—recorded at more than 600 hydroelectric power plants—with historical climate data developed for distinct hydropower subregions of the West. The most extreme impacts of drought on hydroelectric power are found at individual dams where reservoir levels are so low that released water and thus generation becomes severely restricted. These isolated cases often receive widespread media attention, leading to a common misconception that hydroelectric power is an unreliable technology whose role will diminish over time as the western climate produces longer and more severe droughts. Yet, when aggregated to the scale of the West, the observational records of hydropower generation reveal a different story. Even during the most severe droughts experienced since the turn of the century, the western hydropower fleet sustained more than 80% of its typical annual generation. Observational data indicate that drought in 2021 led to the worst year for hydropower generation in the West since 2001, with total generation approximately 16 percent below the 21st century two-decade average. The year 2021 was particularly severe in California (second worst hydro year of last two decades, ~48 percent below average) and Oregon (worst hydro year of last two decades), while generation in Washington and Idaho was affected to a lesser degree (~12 percent below average for combined region). The year 2001 remains the year of lowest western hydropower generation of the twenty-first century so far, owing to extreme drought in the Pacific Northwest, where about two-thirds of western hydropower capacity is located. The primary reason for this relative stability is the diversity of weather across the West; drought rarely impairs hydroelectric power across all river basins at the same time.

13 HYDRO ENERGY↗
DOE OSTI2022

Combined Cycle Integrated Thermal Energy Storage “CiTES” (Final Scientific/Technical Report)

The Phase I of this project confirmed the technical feasibility of a Combined Cycle integrated Thermal Energy Storage “CiTES” system, calculated the key performance parameters like power efficiency and costs, and proved its commercial value with full-year simulations for several US electricity markets with high degree of variable renewable generation and volatile hourly electricity prices. The core element of this project is the Electro Thermal Energy Storage (ETES) technology from Siemens Gamesa Renewable Energy GmbH, using thermally stable and inexpensive volcanic rocks as storage material and air as heat transfer medium. This technology is backed by more than 10 years of experience and a 440MMBTU (130MWh-th) pilot plant in Hamburg, Germany, which is in operation since 2019. The integration of this thermal storage in an existing combined cycle power plant (CCPP) is typical power plant technology without any major technology risks. It allows the storage of inexpensive renewable energy during times of surplus renewable generation and the discharge of this energy in times of high energy demand when the fossil plant is in operation. This supplements the fossil power generation with CO2-emission-free energy. The secondary effect of the CiTES system is that a small part of the stored thermal energy is used to keep the heat recovery steam generator (HRSG) and steam turbine (ST) of the combined cycle power plant in hot and ready-to-start condition. This enables the plant to start rapidly when fossil generation is required to satisfy demand as soon variable generation drops off in the evenings or during cloud cover and calm wind periods. Without pre-warming of the HRSG and ST, the CCPP would need several hours for a cold or warm start, burn a lot of gas and release high NOx emissions during start and wouldn’t be able to use the short times of high energy prices in an efficient or economical manner. The economic parameters of CiTES were determined by a full year “8760” simulation using a data set calculation for each of the hours of the year, and historical electricity and gas prices. For consistency, the simulations were focused on the pre-COVID year 2019. The financially most attractive markets were in the Energy Reliability Council of Texas (ERCOT) region, which allowed substantial value generation with arbitrage (charge with cheap energy during renewable surplus times and discharge when energy is needed and expensive). The improvement of flexibility with the CiTES system by pre-heating and warm-keeping of the CCPP allowed for additional power generation during short time periods when demand is high but renewable generation is down; when the hourly energy prices are highest in these markets. The simulations are based on 2019 data, when ERCOT had 27GW of installed photovoltaic (PV) and wind generation. They showed that the created revenue with the prototypically sized CiTES system of 1,000MMBTU (300MWh-th) falls a little bit short of what is expected from a commercially viable investment. The system has optimization opportunities for cost reduction and increased effectiveness which will be realized during a potential Phase II Pre-FEED study following this project. Furthermore, it is safe to assume that a lot of renewable generation capacity will be added all over the US in the coming years. As an example, ERCOT is predicting to more than double its renewable generation from 27GW in 2019 to a forecasted 63GW in 2023. This will increase the amount of renewable overproduction exponentially. This rapid increase of local overproduction and the need to curtail renewable generation is well documented by the California ISO (www.CAISO.com / managing oversupply). However, the simulations also revealed a weakness in the structure of the electricity markets in the US. More specifically, when electricity prices are very low and approaching negative levels, the owners of Variable Renewable Energy (VRE) will curtail a part of their facility to stabilize the price by reducing supply. This results in a situation in which storage facilities, which are integrated in existing fossil assets and don’t have the behind-the-meter benefit of a VRE, won’t be able to purchase low cost – otherwise curtailed – renewable energy off the grid. A special tariff, which motivates VRE owners to sell otherwise curtailed renewable energy to storage facilities (Hydrogen, thermal, pumped hydro, etc.) can solve this issue. The implementation of such a regulating tariff by Independent System Operators, thus avoiding renewable curtailment, is a pre condition for successful commercialization for renewable energy storage technologies. With this advancement of design and technology and improvements in the market environment, it can be expected that the Combined Cycle integrated Thermal Energy Storage proves itself as an important innovation to keep highly efficient, natural gas-based power generation economically successful and relevant for the power industry in the United States of America.

Wolf, Thorsten↗
DOE OSTI2022

Demand Response Analysis for Different Residential Personas in a Comfort-Driven Behavioral Context

Low demand response (DR) participation and high program drop-out rates continue to impede DR goals that could save up to $13 billion in annual grid expansion and electricity demand costs. Yet, the literature lacks a thorough understanding of how different residential customer segments enrolled in DR programs respond to utility signals in view of occupant comfort considerations. The objective of this study is to gain a clear understanding of the effects of four different customer personas on residential DR. Given current data limitations, this work developed an array of hypothetical personas with varied priorities, activity levels, and comfort thresholds based on demographic variables that have been found in previous studies to influence energy consumption. A BEopt DR model for a reference residential single-family building located in Colorado was built to isolate the effect of differences in buildings or climate. The results provide useful evidence on how persona-comfort differences lead to significant deviations in DR goals (especially peak demand reduction), ranging from 0.1% to 20%. This work presents a novel framework representing comfort preferences in DR models. The data generated, albeit synthetic, and the results could inform DR program design considerations of how different people respond to different comfort priorities.

BEopt↗
DOE OSTI2022

Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered “Oilcane” Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper- accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane”. This study evaluates the potential of oilcane as a renewable feedstock for the co- production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. Here, this allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Data for Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered ‘Oilcane’ Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper-accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane.” This study evaluates the potential of oilcane as a renewable feedstock for the co-production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. This allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

Conversion↗