SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Kinetics of hot pressed molybdenum disulfide and molybdenum disulfide-silver compositions with effect on electric conduction processes
The lubricating properties of a straight mineral oil with and without MoS2 powder were studied. Bearing testers of thrust-collar type and of journal bearing type were used for thin- and fluid-film conditions, respectively. The effectiveness of the MoS2 powder in the oil differed depending on the conditions of the rubbing surfaces. For fluid film conditions, considerable effects of the MoS2 were observed, in contrast to the thin-film cases. The addition of MoS2 powder was effective only when the lubricant film was formed between surfaces thickly enough to allow the inflow of MoS2 particles.
Sliding friction experiments were conducted with molybdenum disulfide single crystals in contact with sputter cleaned surfaces of copper, nickel, gold, and 304 stainless steel. Transfer of the molybdenum disulfide to the metals was monitored with Auger electron spectroscopy. Results of the investigation indicate molybdenum disulfide transfers to all clean metal surfaces after a single pass over the metal surface with film thickness observed to increase with repeated passes over the same surfaces. Large particle transfer occurs when the orientation of the crystallites is other than basal. This is frequently accompanied by abrasion of the metal. Adhesion of molybdenum disulfide films occurred readily to copper and nickel, less readily to 304 stainless steel, and even less effectively to the gold, which indicates a chemical effect.
Carbon disulfide (CS2) measurements were made over the western and equatorial North Atlantic Ocean and the northwestern and equatorial South Atlantic Ocean. Carbon disulfide was in the range 0.4-50 pptrv in the atmosphere of the western North Atlantic Ocean. Emissions from anthropogenic sources and wet lands were found to be important although anthropogenic sources were 4-6 times larger than biogenic sources. The flux of CS2 from eastern North America between 30 and 39 deg latitude was estimated to be 2 x 10(exp 8)g/yr or sulfur. The anthropogenic contribution was 1.8 x 10(exp 8)g/yr of sulfur whereas the contribution of marshes was 0.2 x 10(exp 8)g/yr of sulfur. Sources of CS2 at high latitudes in the northern hemisphere were comparatively weak. Carbon disulfide levels in the western South Atlantic Ocean between -5 and 1 deg latitude were in the range 0.2-6 pptrv. Most of the CS2 appeared to come from biomass burning in Africa. Carbon disulfide was much higher close to shore suggesting that the South American continent was a significant source although too few data were available to quantify it. On ferry lights from Wallops, Virginia to Natal, Brazil, CS2 levels at the ferry altitude of about 6 km averaged 1.2 pptrv. This background CS2 was adequate to account for all the carbonyl sulfide (OCS) in the atmosphere.
Two coatings for a Rayleigh step thrust bearing were tested when coasting down and stopping under self-acting operation in air. The thrust bearing had an outside diameter of 8.9 cm (3.5 in.), an inside diameter of 5.4 cm (2.1 in.), and nine sectors. The load was 73 N (16.4 lbf). The load pressure was 19.1 kN/per square meter (2.77 lbf/per square inch) on the total thrust bearing area. The chromium oxide coating was good to 150 stops without bearing deterioration, and the molybdenum disulfide coating was good for only four stops before bearing deterioration. The molybdenum disulfide coated bearing failed after nine stops.
TiS2, VS2, and Nb(1.1)S2 transition metal disulfides were evaluated as cathode materials for a moderate temperature rechargeable Na cell operating at 130 C. The 1st discharge of TiS2 results in a capacity of 0.85 eq/mole; approximately half of the Na in the 1st phase spanning the Na range from zero to 0.30 and almost all the Na in the 2nd phase spanning the 0.37 to 0.80 range are rechargeable. VS2 intercalates up to one mole of Na/mole of VS2 in the 1st discharge; the resulting Na(x)VS2 ternary consists of 3 phases in the 3 ranges of Na from zero to 1. Niobium disulfide undergoes a phase change in the 1st discharge; the average rechargeable capacity in extended cycling of this cathode is 0.50 eq/mole.
A gas chromatograph/mass spectrometer is described for determining atmospheric sulfur dioxide, carbon disulfide, dimethyl sulfide, and carbonyl sulfide from aircraft and ship platforms. Isotopically labelled variants of each analyte were used as internal standards to achieve high precision. The lower limit of detection for each species for an integration time of 3 min was 1 pptv for sulfur dioxide and dimethyl sulfide and 0.2 pptv for carbon disulfide and carbonyl sulfide. All four species were simultaneously determined with a sample frequency of one sample per 6 min or greater. When only one or two species were determined, a frequency of one sample per 4 min was achieved. Because a calibration is included in each sample, no separate calibration sequence was needed. Instrument warmup was only a few minutes. The instrument was very robust in field deployments, requiring little maintenance.
Five different mixtures of molybdenum disulfide are found to be effective bearing lubricants when tested at very low pressures and high temperatures.
Motor brushes of proper quantities of molybdenum disulfide and copper or silver are manufactured by sintering techniques. Graphite molds are used. These brushes operate satisfactorily for long periods in normal atmosphere or in a high-vacuum environment.
Wear life analysis of hot pressed molybdenum disulfide-silver electrical contact brushes in vacuum
Electrophoretic deposition of metal bonded molybdenum disulfide for gear lubrication
Molybdenum disulfide lubricant film is deposited on two substrates, niobium and nickel-chromium alloys, by means of physical direct-current sputtering. The sputtering system uses a three-electrode /triode/ geometry - a thermionic cathode, an anode, and the target, all enclosed in a vacuum chamber.
Sputtered molybdenum disulfide film deposition and friction characteristics in vacuum
Molybdenum disulfide as lubricant, discussing use in bonded solid films, low concentration liquid mixtures, etc
Thermal stability and friction of disulfides, diselenides, and ditellurides of molybdenum and tungsten in ultrahigh vacuum
Friction and contact resistance during sliding in vacuum of low resistivity metals lubricated with sputtered molybdenum disulfide
Quantitative and qualitative analysis of biochemically and radiobiologically important thiols and disulfides via gas-liquid chromatography
Small additions /0.01 percent or less/ of triethanoloamine sodium sulfite adduct to mercapto benzothiazole inhibited glycol water heat transfer solutions containing disulfide precipitate produce marked reduction in amount of precipitate. Adduct is useful as additive in glycol base antifreezes and coolants.