Results for “distance-based modeling”

NASA NTRS1992

Environmental fatigue of an Al-Li-Cu alloy. Part 2: Microscopic hydrogen cracking processes

Based on a fractographic analysis of fatigue crack propagation (FCP) in Al-Li-Cu alloy 2090 stressed in a variety of inert and embrittling environments, microscopic crack paths are identified and correlated with intrinsic da/dN-delta K kinetics. FCP rates in 2090 are accelerated by hydrogen producing environments (pure water vapor, moist air, and aqueous NaCl), as defined in Part 1. For these cases, subgrain boundary fatigue cracking (SGC) dominates for delta K values where the crack tip process zone, a significant fraction of the cyclic plastic zone, is sufficiently large to envelop 5 micron subgrains in the unrecrystallized microstructure. SGC may be due to strong hydrogen trapping at T1 precipitates concentrated at sub-boundaries. At low delta K, the plastic zone diameter is smaller than the subgrain size and FCP progresses along (100) planes due to either local lattice decohesion or aluminum-lithium hydride cracking. For inert environments (vacuum, helium, and oxygen), or at high delta K where the hydrogen effect on da/dN is small, FCP is along (111) slip planes; this mode does not transition with increasing delta K and plastic zone size. The SGC and (100) crystallographic cracking modes, and the governing influence of the crack tip process zone volume (delta K), support hydrogen embrittlement rather than a surface film rupture and anodic dissolution mechanism for environmental FCP. Multi-sloped log da/dN-log delta K behavior is produced by changes in process zone hydrogen-microstructure interactions, and not by purely micromechanical-microstructure interactions, in contradiction to microstructural distance-based fatigue models.

Robert S Piascik↗

NASA NTRS2005

Evaluation of Airborne Precision Spacing in a Human-in-the-Loop Experiment

A significant bottleneck in the current air traffic system occurs at the runway. Expanding airports and adding new runways will help solve this problem; however, this comes with significant costs: financially, politically and environmentally. A complementary solution is to safely increase the capacity of current runways. This can be achieved by precisely spacing aircraft at the runway threshold, with a resulting reduction in the spacing bu er required under today s operations. At NASA's Langley Research Center, the Airspace Systems program has been investigating airborne technologies and procedures that will assist the flight crew in achieving precise spacing behind another aircraft. A new spacing clearance allows the pilot to follow speed cues from a new on-board guidance system called Airborne Merging and Spacing for Terminal Arrivals (AMSTAR). AMSTAR receives Automatic Dependent Surveillance-Broadcast (ADS-B) reports from an assigned, leading aircraft and calculates the appropriate speed for the ownship to fly to achieve the desired spacing interval, time- or distance-based, at the runway threshold. Since the goal is overall system capacity, the speed guidance algorithm is designed to provide system-wide benefits and stability to a string of arriving aircraft. An experiment was recently performed at the NASA Langley Air Traffic Operations Laboratory (ATOL) to test the flexibility of Airborne Precision Spacing operations under a variety of operational conditions. These included several types of merge and approach geometries along with the complementary merging and in-trail operations. Twelve airline pilots and four controllers participated in this simulation. Performance and questionnaire data were collected from a total of eighty-four individual arrivals. The pilots were able to achieve precise spacing with a mean error of 0.5 seconds and a standard deviation of 4.7 seconds. No statistically significant di erences in spacing performance were found between in-trail and merging operations or among the three modeled airspaces. Questionnaire data showed general acceptance for both pilots and controllers. These results reinforce previous findings from full-mission simulation and flight evaluation of the in-trail operations. This paper reviews the results of this simulation in detail.

Barmore, Bryan E.↗

NASA NTRS2015

Well Clear: General Aviation and Commercial Pilots' Perceptioin of Unmanned Aerial Vehicles in the National Airspace System

This research explored how different pilots perceived the concept of the Well Clear Boundary (WCB) and observed if that boundary changed when dealing with manned versus unmanned aircraft systems (UAS), and the effects of other variables. Pilots' WCB perceptions were collected objectively through simulator recordings and subjectively through questionnaires. Objectively, significant differences were found in WCB perception between two pilot types (general aviation [GA], and Airline Transport Pilots [ATPs]), and significant WCB differences were evident when comparing two intruder types (manned versus unmanned aircraft). Differences were dependent on other manipulated variables (intruder approach angle, ownship speed, and background traffic levels). Subjectively, there were differences in WCB perception across pilot types; GA pilots trusted UAS aircraft higher than the more experienced ATPs. Conclusions indicate pilots' WCB mental models are more easily perceived as time-based boundaries in front of ownship, and more easily perceived as distance-based boundaries to the rear of ownship.

unmanned aerial systems↗

NASA NTRS2019

Accrued Delay Application in Trajectory-Based Operations

The air traffic management system lacks integration among its elements often due to using inconsistent information, models, and metrics about the traffic. Transitioning to trajectory-based operations, whereby flights are managed by full trajectories in space and time, will enable more integration, with the help of increased automation. Building on trajectory-based operations, an "accrued delay" metric is proposed, which continuously measures the amount of delay that a flight has accumulated up to the current time, including delays incurred during the current flight and inherited from previous flights through the turnaround process. Through a time-based metering and scheduling example, we show how using accrued delay as a metric can help integrate the decision-making across multiple decision horizons, leading to more efficient and balanced access to airspace services. We show that when prioritizing flights that have already accrued high delay because of a constrained runway resource, significant gains are achieved in terms of reducing total delay and its variance. We studied the sensitivity of these gains to numerous factors, such as time-based versus distance-based horizons, horizon size, and errors in conformance to scheduled times.

delay; trajectory-based operations; time-based flo↗

NASA NTRS2019

Accrued Delay Application in Trajectory-Based Operations

The air traffic management system lacks integration among its elements often due to using inconsistent information, models, and metrics about the traffic. Transitioning to trajectory-based operations, whereby flights are managed by full trajectories in space and time, will enable more integration, with the help of increased automation. Building on trajectory-based operations, an "accrued delay" metric is proposed, which continuously measures the amount of delay that a flight has accumulated up to the current time, including delays incurred during the current flight and inherited from previous flights through the turnaround process. Through a time-based metering and scheduling example, we show how using accrued delay as a metric can help integrate the decision-making across multiple decision horizons, leading to more efficient and balanced access to airspace services. We show that when prioritizing flights that have already accrued high delay because of a constrained runway resource, significant gains are achieved in terms of reducing total delay and its variance. We studied the sensitivity of these gains to numerous factors, such as time-based versus distance-based horizons, horizon size, and errors in conformance to scheduled times.

Idris, Husni↗