Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “direct use”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Optimization of boron carbide density using direct current sintering for use as sputtering sources at the National Ignition Facility

Several experimental trials were conducted to determine optimal sintering parameters and compositions for purchased boron carbide powder using spark plasma sintering/direct current sintering. Sputtering targets used to create ablators for the National Ignition Facility have been unable to survive post processing procedures suggesting that in-house fabrication may yield better results due to extended control.

36 MATERIALS SCIENCE↗
NASA NTRS1986

An analysis of bi-directional use of frequencies for satellite communications

The bi-directional use of frequencies allocated for space communications has the potential to double the orbit/spectrum capacity available. The technical feasibility of reverse band use (RBU) at C-band (4 GHz uplinks and 6 GHz downlinks) is studied. The analysis identifies the constraints under which both forward and reverse band use satellite systems can share the same frequencies with terrestrial, line of sight transmission systems. The results of the analysis show that RBU satellite systems can be similarly sized to forward band use (FBU) satellite systems. In addition, the orbital separation requirements between RBU and FBU satellite systems are examined. The analysis shows that a carrier to interference ratio of 45 dB can be maintianed between RBU and FBU satellites separated by less than 0.5 deg., and that a carrier to interference ratio of 42 dB can be maintained in the antipodal case. Rain scatter propagation analysis shows that RBU and FBU Earth stations require separation distances fo less than 10 km at a rain rate of 13.5 mm/hr escalating to less than 100 km at a rain rate of 178 mm/hr for Earth station antennas in the 3 to 10 m range.

Whyte, W. A., Jr.↗
NASA NTRS1986

An analysis of bi-directional use of frequencies for satellite communications

The bi-directional use of frequencies allocated for space communications has the potential to double the orbit/spectrum capacity available. The technical feasibility of reverse band use (RBU) at C-band (4 GHz uplinks and 6 GHz downlinks) is studied. The analysis identifies the constraints under which both forward and reverse band use satellite systems can share the same frequencies with terrestrial, line of sight transmission systems. The results of the analysis show that RBU satellite systems can be similarly sized to forward band use (FBU) satellite systems. In addition, the orbital separation requirements between RBU and FBU satellite systems are examined. The analysis shows that a carrier to interference ratio of 45 dB can be maintained between RBU and FBU satellites separated by less than 0.5 deg, and that A carrier to interference ratio of 42 dB can be maintained in the antipodal case. Rain scatter propagation analysis shows that RBU and FBU earth stations require separation distances of less than 10 km at a rain rate of 13.5 mm/hr escalating to less than 100 km at a rain rate of 178 mm/hr for earth station antennas in the 3 to 10 m range.

Whyte, W. A., Jr.↗
NASA NTRS1979

Gust alleviation using direct turbulence measurements

The research reported upon in this paper describes an effective method of gust alleviation using direct measurements of atmospheric turbulence to drive the aircraft control surfaces in a way that attempts to directly counter or cancel those forces and moments produced on the aircraft by gusts. The method yields a feedforward or open loop control law, simple to mechanize and relatively insensitive to changes in flight condition. When applied directly, the resulting control law effectively gust-alleviates in the low frequency phugoid and short period range but has a tendency to amplify structural mode vehicle motions due to the phase lag of the actuators. A method of design based upon the use of a diagonal or Jordan form of the equations of motion enables the designer to avoid this problem of structural mode excitation.

Rynaski, E. G.↗
DOE OSTI2025

Secondary electron emission for reticulated carbon foam surfaces using direct measurements and spectroscopic analysis

This study investigates secondary electron emission (SEE) characteristics of reticulated foams using direct measurements and analytical modeling. Total SEE was quantified, revealing suppression of up to 44% in carbon foam structures compared to planar graphite surfaces. An optimal geometric configuration was identified and supported by analytical models. SEE angular dependence experiments showed diverse behaviors: fiber-like behavior and directional dependence for pore and ligaments on the mm scale, with fuzz-like characteristics when the foam features are between 10–100 µm. Electron energy analyzer measurements showed that carbon foams preferentially suppress inelastic backscattered electrons (BSEs) more so than true secondary electrons (SEs). The analysis indicated a larger fraction of low-energy SE generation in foams compared to flat surfaces due to increased emission from curved fiber ligaments and tertiary SEs from high-energy BSEs. These findings have implications for design and optimization of materials with tailored electron emission properties for applications like plasma-facing components, spacecraft materials, and accelerator surfaces.

Auger↗
NASA NTRS2000

Autogeneous Friction Stir Weld Lack-of-Penetration Defect Detection and Sizing Using Directional Conductivity Measurements with MWM Eddy Current Sensor

Al 2195-T8 plate specimens containing Friction Stir Welds (FSW), provided by Lockheed Martin, were inspected using directional conductivity measurements with the MWM sensor. Sensitivity to lack-of-penetration (LOP) defect size has been demonstrated. The feature used to determine defect size was the normalized longitudinal component of the MWM conductivity measurements. This directional conductivity component was insensitive to the presence of a discrete crack. This permitted correlation of MWM conductivity measurements with the LOP defect size as changes in conductivity were apparently associated with metallurgical features within the first 0.020 in. of the LOP defect zone. Transverse directional conductivity measurements also provided an indication of the presence of discrete cracks. Continued efforts are focussed on inspection of a larger set of welded panels and further refinement of LOP characterization tools.

Goldfine, Neil↗
NASA NTRS2002

Measurement Of Trailing Edge Noise using Directional Array and Coherent Output Power Methods

The use of a directional array of microphones for the measurement of trailing edge (TE) noise is described. The capabilities of this method are evaluated via measurements of TE noise from a NACA 63-215 airfoil model and from a cylindrical rod. This TE noise measurement approach is compared to one that is based on the cross spectral analysis of output signals from a pair of microphones (COP method). Advantages and limitations of both methods are examined. It is shown that the microphone array can accurately measures TE noise and captures its two-dimensional characteristic over a large frequency range for any TE configuration as long as noise contamination from extraneous sources is within bounds. The COP method is shown to also accurately measure TE noise but over a more limited frequency range that narrows for increased TE thickness. Finally, the applicability and generality of an airfoil self-noise prediction method was evaluated via comparison to the experimental data obtained using the COP and array measurement methods. The predicted and experimental results are shown to agree over large frequency ranges.

Hutcheson, Florence V.↗
NASA NTRS2002

Measurement of Trailing Edge Noise Using Directional Array and Coherent Output Power Methods

The use of a directional (or phased) array of microphones for the measurement of trailing edge (TE) noise is described and tested. The capabilities of this method arc evaluated via measurements of TE noise from a NACA 63-215 airfoil model and from a cylindrical rod. This TE noise measurement approach is compared to one that is based on thc cross spectral analysis of output signals from a pair of microphones placed on opposite sides of an airframe model (COP method). Advantages and limitations of both methods arc examined. It is shown that the microphone array can accurately measures TE noise and captures its two-dimensional characteristic over a large frequency range for any TE configuration as long as noise contamination from extraneous sources is within bounds. The COP method is shown to also accurately measure TE noise but over a more limited frequency range that narrows for increased TE thickness. Finally, the applicability and generality of an airfoil self-noise prediction method was evaluated via comparison to the experimental data obtained using the COP and array measurement methods. The predicted and experimental results are shown to agree over large frequency ranges.

Hutcheson, Florence V.↗
DOE OSTI2025

Computational Study of a Cryopump Design for Fusion Exhaust Gas Purification Using Direct Simulation Monte Carlo

Cryopump-based direct internal recycling (DIR) of fusion fuel is an attractive prospect because it provides pumping of helium ash from a reactor along with separation of helium and other impurities from the fuel. Previous studies have demonstrated a continuously regenerating cryopump, referred to as the Snail pump, that separates helium ash from fusion fuel for reactor-relevant flow rates. Here, in this study, a conceptual cryopump was designed as a proof-of-principle study to target other impurities, besides helium ash, from the fusion exhaust that would complement the Snail pump. The impurity-removal cryopump consists of four sets of chevron fins, two sets operating at 80 K and the other two at 30 K. A computational study using direct simulation Monte Carlo (DSMC) was performed with a gas mixture of 96.5% D2, 2.0% He, and 0.5% each of CO2, N2, and CH4. In this configuration, 80 K chevron fin sets are capable of capturing CO2 and 30 K sets capable of capturing CO2, N2, and CH4. The computational study showed that the cryopump is capable of reducing the impurity content by more than two orders of magnitude from the flow.

Adhikari, Nirajan [Oak Ridge National Laboratory (↗
DOE OSTI2025

Disentangling Centrality Bias and Final-State Effects in the Production of High-𝑝 𝑇 Neutral Pions Using Direct Photon in 𝑑+Au Collisions at $\sqrt{s_{NN}}$ = 200 GeV

Here, PHENIX presents a simultaneous measurement of the production of direct 𝛾 and 𝜋 0 in 𝑑 + Au collisions at $\sqrt{s_{NN}}$ = 200 GeV over a 𝑝 𝑇 range of 7.5 to 18 GeV/𝑐 for different event samples selected by event activity, i.e., charged-particle multiplicity detected at forward rapidity. Direct-photon yields are used to empirically estimate the contribution of hard-scattering processes in the different event samples. Using this estimate, the average nuclear-modification factor, 𝑅$^{𝜋^0}_{dAu,EXP}$, is 0.925 ± 0.023⁢(stat) ± 0.15⁢(scale), consistent with unity for minimum-bias (MB) 𝑑+Au collisions. For event classes with low and moderate event activity, 𝑅$^{𝜋^0}_{dAu,EXP}$ is consistent with the MB value within 5% uncertainty. This result confirms that the previously observed enhancement of high-𝑝 𝑇 𝜋 0 production found in small-system collisions with low event activity is a result of a bias in interpreting event activity within the Glauber framework. In contrast, for the top 5% of events with the highest event activity, 𝑅$^{𝜋^0}_{dAu,EXP}$ is suppressed by 20% relative to the MB value with a significance of 4.5⁢𝜎, which may be due to final-state effects. This suppression corresponds to a 𝑝 𝑇 shift of 𝛿⁢𝑝 𝑇 = 0.213 ± 0.055 Gev/𝑐 at 9 Gev/𝑐.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1990

Active turbulence control in wallbounded flow using direct numerical simulations

An exploratory study of concepts for active control of turbulent boundary layers using the direct numerical simulation technique was performed. Significant drag reduction was achieved when the surface boundary condition was modified such that it could suppress the large-scale structures present in the wall region. This was achieved by prescribing the normal component of velocity at the wall to be 180 deg out of phase with the normal velocity slightly above the wall at each instant. The drag reduction was accompanied with significant reduction in the intensity of the wall-layer structures and reductions in the magnitude of Reynolds stresses throughout the flow. Suitability of wall-pressure and shear-stress fluctuations for detection of flow structures above the wall was examined. A preliminary result obtained by applying the present control strategy to a transitional flow is also briefly described, from which one can infer a possible linkage between the control strategy and flow stability.

Kim, J.↗
NASA NTRS1992

Shock interference prediction using direct simulation Monte Carlo

The shock interaction produced when an incident shock impinges on an inlet cowl lip is investigated for a cowl lip radius of 0.1 in. and flight conditions of Mach 15 and 35-km altitude. This problem is of interest in the design of hypersonic flight vehicles because the interference heating at the cowl lip surface from such a shock interaction is expected to be very high and the design of adequate thermal protection in this region will be challenging. Noncontinuum effects may be significant at this combination of altitude and small dimensions. If this is so, a computational solution based on the Navier-Stokes equations could significantly overpredict the surface heating on the cowl lip. Therefore, a kinetic theory solution technique, direct simulation Monte Carlo (DSMC), is used to predict the flowfield and surface heating. The details of modeling this problem and some preliminary results are presented. The same qualitative flow patterns are seen with DSMC and a continuum solution of the shock interference case, but the peak heating predicted with DSMC is somewhat lower.

Carlson, Ann B.↗
NASA NTRS1993

Three-dimensional hypersonic rarefied flow calculations using direct simulation Monte Carlo method

A summary of three-dimensional simulations on the hypersonic rarefied flows in an effort to understand the highly nonequilibrium flows about space vehicles entering the Earth's atmosphere for a realistic estimation of the aerothermal loads is presented. Calculations are performed using the direct simulation Monte Carlo method with a five-species reacting gas model, which accounts for rotational and vibrational internal energies. Results are obtained for the external flows about various bodies in the transitional flow regime. For the cases considered, convective heating, flowfield structure and overall aerodynamic coefficients are presented and comparisons are made with the available experimental data. The agreement between the calculated and measured results are very good.

Celenligil, M. Cevdet↗
NASA NTRS1978

Estimates of oceanic surface wind speed and direction using orthogonal beam scatterometer measurements and comparison of recent sea scattering theories

The wind direction properties of radar backscatter from the sea were empirically modelled using a cosine Fourier series through the 4th harmonic in wind direction (referenced to upwind). A comparison with 1975 JONSWAP (Joint North Sea Wave Project) scatterometer data, at incidence angles of 40 and 65, indicates that effects to third and fourth harmonics are negligible. Another important result is that the Fourier coefficients through the second harmonic are related to wind speed by a power law expression. A technique is also proposed to estimate the wind speed and direction over the ocean from two orthogonal scattering measurements. A comparison between two different types of sea scatter theories, one type presented by the work of Wright and the other by that of Chan and Fung, was made with recent scatterometer measurements. It demonstrates that a complete scattering model must include some provisions for the anisotropic characteristics of the sea scatter, and use a sea spectrum which depends upon wind speed.

Moore, R. K.↗
NASA NTRS1995

Method for determining shear direction using liquid crystal coatings

A method is provided for determining shear direction wherein a beam of white light is directed onto the surface of a liquid crystal coating to cause the white light to be dispersed (reflected) from the surface in a spectrum having bands of different colors in a fixed spatial 2 (angular) sequence. The system is calibrated by locating an observer, e.g., a video and movie camera, such that a particular color band (preferably at or near the center of the reflected spectrum) is observed to thereby provide a reference color band. Because the application of shear causes either clockwise or counterclockwise rotation of the reflected spectrum dependent on the direction of the shear, a determination is then made of the reflected color band observed by the observer when the surface of the liquid crystal is subjected to shear to thereby determine the direction of the shear based on the directional (rotation) relation of the observed color band with respect to the reference color band in the spatial sequence of color bands.

Reda, Daniel C.↗
DOE OSTI2026

Geothermal Direct-Use Applications for the District Energy System in Bucharest, Romania

The city of Bucharest, Romania, hosts the second-largest district energy system (DES) in the world. Geothermal resources can be considered as a supplementary heat source to support the demand for domestic hot water and space heating in the winter and shoulder seasons. The National Laboratory of the Rockies (NLR) has conducted a study that considers geothermal energy to serve a fraction of the existing district heating network operated by Electrocentrale Bucure?ti (ELCEN), the utility operating the DES. Lower Cretaceous and Jurassic limestones make up the main geothermal aquifer underlying Bucharest, which hosts temperatures suitable for district heating (up to 90 degrees C to the north of the city). Anomalous geothermal gradients have been observed to the north of the city, where a pumped well has produced 82 degrees C brine at the wellhead to feed the Therme Bucharest Spa. An anomalous gradient has also been reported to the southeast of the city (35 degrees C/km). NLR modeled the building heating loads of a small portion of the DES (a block of nine prototypical buildings) in its Urban Renewable Building and Neighborhood Optimization (URBANopt ) platform. To simulate meeting a baseload benchmark of 20 MWth deliverable to a small portion of the DES, the NLR team used GEOPHIRES to model production scenarios for (1) hydrothermal systems coupled with heat pumps targeting the main geothermal aquifer in the north, (2) enhanced geothermal systems targeting hot dry rock in the southeast, and (3) huff-and-puff systems targeting a gradient of 25 degrees C/km. Finally, NLR conducted a high-level sensitivity study around the techno-economics of these systems. The outcomes of this work indicate that hot dry rock geothermal resources that can deliver at least 90 degrees C hot water to the Geothermal District Energy System (GeoDES) offer a possible solution for supplemental geothermal heat delivered to the existing DES.

15 GEOTHERMAL ENERGY↗
NASA NTRS1993

Calculation of optimum airfoils using direct solutions of the Navier-Stokes equations

A method has been developed which calculates the optimum airfoil shape at a specified operating condition. The Reynolds-averaged Navier-Stokes equations with a turbulence model are used as the governing equations for the fluid flow, and are explicitly introduced into the optimization analysis as constraint equations. The locations of all grid points which define the surface of the airfoil are design variables, eliminating the need for shape functions to describe changes in the airfoil geometry. A generalized reduced-gradient method is used to find the optimum airfoil shape. The use of a direct solution technique (Newton's method) to solve the Navier-Stokes equations allows for the efficient solution of the problem. This paper describes the optimization method and presents sample results.

Felker, Fort F.↗