SEARCH · Engineering Papers
Results for “deformation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effects of Photovoltaic Module Materials and Design on Module Deformation Under Load
Static structural finite element models of an aluminum-framed crystalline silicon (c-Si) photovoltaic (PV) module and a glass-glass thin film PV module were constructed and validated against experimental measurements of deflection under uniform pressure loading. Parametric analyses using Latin Hypercube Sampling (LHS) were performed to propagate simulation input uncertainties related to module material properties, dimensions, and manufacturing tolerances into expected uncertainties in simulated deflection predictions. This exercise verifies the applicability and validity of finite element modeling for predicting mechanical behavior of solar modules across architectures and enables computational models to be used with greater confidence in assessment of module mechanical stressors and design for reliability. Sensitivity analyses were also performed on the uncertainty quantification data sets using linear correlation coefficients to elucidate the key parameters influencing module deformation. This information has implications on which materials or parameters may be optimized to best increase module stiffness and reliability, whether the key optimization parameters change with module architecture or loading magnitudes, and whether parameters such as frame design and racking must be replicated in reduced-scale reliability studies to adequately capture full module mechanical behavior.
Single-Step Shear-Based Deformation Processing of Electrical Conductor Wires
Commercial electrical conductor wires are currently produced from aluminum alloys by multi-step deformation processing involving rolling and drawing. These processes typically require 10 to 20 steps of deformation, since the plastic strain or reduction that can be imposed in a single step is limited by material workability and process mechanics. Here, we demonstrate a fundamentally different, single-step approach to produce flat wire aluminum products using machining-based deformation that also ensures adequate material workability in the formed product. Two process routes are proposed: (1) chip formation by free-machining (FM), with a post-machining, light drawing reduction (<20%) to achieve desired finish and (2) constrained chip formation by large strain extrusion machining (LSEM). Using commercially pure aluminum conductor alloys (Al 1100 and EC1350) as representative material systems, we demonstrate key features of the machining-based processing, including (a) single-step processing to achieve flat wire geometries, (b) surface finish (Ra = 0.2 to 1.0 μm) comparable to that of commercial wire products made by drawing/rolling, (c) deformation control independent of wire size, and (d) hardness increases of 50–150% over that of annealed wires, while retaining high electrical conductivity (>56% IACS). Here, the wire microstructure, which can also be varied via the large-strain deformation parameters, is correlated with mechanical and electrical properties. Implications for commercial manufacture of flat wire products are discussed.
Characterization of mechanical deformation in aluminum by optical second harmonic generation
Second harmonic generation (SHG), a laser-based surface technique, was used to characterize near-surface defect evolution associated with mechanical deformation in 2024-T3 aluminum due to tensile loads. Electron backscatter diffraction (EBSD) measurements were also performed to determine the geometrically necessary dislocation density before and after tensile deformation. Comparison of the EBSD and SHG results found that dislocation density and SHG signal are inversely proportional; tensile deformation in the plastic regime led to an increase in dislocation density and a decrease in SHG response. A similar trend was seen in the SHG results on as-received (unpolished) Al samples; SHG response decreases with extent of plastic deformation. Furthermore, this study suggests that SHG has potential as a nondestructive evaluation technique.
X-ray computed tomography analysis of pore deformation in IN718 made with directed energy deposition
Explore the source record for details and available documents.
Surf-Deformer: Mitigating Dynamic Defects on Surface Code via Adaptive Deformation
In this paper, we introduce Surf-Deformer, a code deformation framework that seamlessly integrates adaptive defect mitigation functionality into the current surface code workflow. It crafts several basic deformation instructions based on fundamental gauge transformations, which can be combined to explore a larger design space than previous methods. This enables more optimized deformation processes tailored to specific defect situations, restoring the QEC capability of deformed codes more efficiently with minimal qubit resources. Additionally, we design an adaptive code layout that accommodates our defect mitigation strategy while ensuring efficient execution of logical operations. Our evaluation shows that Surf-Deformer outperforms previous methods by significantly reducing the end-to-end failure rate of various quantum programs by 35× to 70×, while requiring only about 50% of the qubit resources compared to the previous method to achieve the same level of failure rate. Ablation studies show that Surf-Deformer surpasses previous defect removal methods in preserving QEC capability and facilitates surface code communication by achieving nearly optimal throughput.
Elastic plastic self-consistent (EPSC) modeling of San Carlos olivine deformed in a D-DIA apparatus
Abstract not provided
In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites
An ultra-low-strain deformation microstructure was revealed for the first time non-destructively in the bulk interior of an annealed laminated Ti-Al composite-in the "fully recrystallized" Al layer-by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM), through real space mapping with a very high angular resolution (0.01 degrees). This ultra-low-strain deformation microstructure was found to result from the thermal stress, induced during cooling after annealing, due to the different coefficients of thermal expansion for the Ti and Al layers. The annealed sample was further tensile deformed to a strain of 1.66% and followed by in situ DAXM and analyzed by various misorientation mapping methods. The results pointed to the important effects of the initial microstructure and the interface constraint, as well as the grain size and crystal orientation, on the plastic deformation. A gradient in dislocation density from the layer interface to the center was found in the Al layer of the annealed sample, and this gradient increased slightly during tensile deformation. The variation of the dislocation density was further discussed based on the activation and interaction of dislocations in grains of different sizes and orientations during plastic deformation. The findings of this study provided valuable insights in understanding the constraint effect of the laminated metal composite and the design of novel composite materials. (c) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Deformation of Polycrystalline MgO Up to 8.3 GPa and 1270 K: Microstructures, Dominant Slip-Systems, and Transition to Grain Boundary Sliding
Ferropericlase is the second most abundant mineral in the Earth’s lower mantle and its mechanical properties have a strong influence on the rheology of this region. Here, we deform polycrystalline MgO, the magnesium end-member of ferropericlase, at conditions ranging from 1.6 to 8.3 GPa and 875–1,270 K. We analyse the flow laws and microstructures of the recovered samples using electron microscopy and compare our observations with predictions from the literature. We identify a first mechanism for samples deformed at 1,270 K, attributed to a regime controlled by grain boundary sliding accommodated by diffusion, and characterized by a small grain size, an absence of texture, and no intracrystalline deformation. At 1,070 K and below, the deformation regime is controlled by dislocations. The samples show a more homogeneous grain size distribution, significant texture, and intracrystalline strains. In this regime, deformation is controlled by the ⟨110⟩{110} slip system and a combined ⟨110⟩{110} and ⟨110⟩{100} slip, depending on pressure and temperature. Based on these results, we propose an updated deformation map for polycrystalline MgO at mantle conditions. The implications for ferropericlase and seismic observations in the Earth’s lower mantle are discussed.
The Application of Canned Deformation to a Hard-Deformed Spray-Deposited Al-Zn-Mg-Cu Alloy
A wide variety of industrial applications require Al-Zn-Mg-Cu alloys with high strength and ductility. However, Zn-rich Al-Zn-Mg-Cu alloys prepared by rapid solidification methods usually show excellent strength but poor formability, which restricts their wide application in complex forming. In this study, we developed a new deformation method for the spray-deposited Zn-rich Al-Zn-Mg-Cu alloy to avoid crack formation and achieve isotropic properties. The microstructure evolution and crystallographic textures were analyzed and compared with the results of a normal deformation process. Crack-free forgings with the ultimate tensile strength (UTS), yield strength (YS) and elongation of 727 ± 5 MPa, 690 ± 3 MPa, 5.0 ± 0.7% along the radial direction and 735 ± 2 MPa, 693 ± 3 MPa, 6.3 ± 0.2% along the tangential direction were finally obtained. The improvement in the mechanical properties can be attributed to the larger amount of subgrains and substructures generated in the canned deformed alloy. The results of this study show excellent advantages and potential application prospects of the canned deformation to hard-deformed Al-Zn-Mg-Cu alloys.
Observations on the deformation of metal microspheres in shock-driven polymer flows
We report that solid particles can be fragmented by a fast-moving fluid if their velocity difference is great enough, such as during the atmospheric entry of meteoroids or the shock compression of engineered particulate composites. The extent of particle deformation and breakup in such systems is poorly understood because the necessary extreme conditions make observation difficult and data scarce. To meet this need, experiments combining ultrafast synchrotron-based radiography with plate impact loading were performed at the dynamic compression sector at the advanced photon source. Metal microspheres of several densities and strengths (Au, Ta, and W) were placed inside a polymer matrix. A planar shock wave was then produced in the polymer by the impact of a gun-launched flyer plate. X-ray images of the resulting flow were collected at ~150ns intervals. These images document the progression of particle deformation across a range of flow conditions and particle materials. They show that the extent of deformation is sensitive to the ratio of drag stress to particle strength. The deforming particle's shape is determined by the initial shock–particle interaction, fluid stagnation pressure, and vorticity, each acting on its own timescale. A set of scaling relationships is presented to capture these observations and enable comparison with prior hydrodynamic data. The result is a framework for predicting the conditions under which strong particles are severely deformed by a shock-driven flow.
Production of Large Disks from Cylindrical Blanks by Plastic Deformation. 4. Deformation of a Protrusion by an Annular Punch
The deformation of a protrusion by a peripheral annular punch is mathematically described. The protrusion is formed as a result of central-punch introduction in the manufacture of large disks or hard-to-deform disks by plastic deformation. The maximum force at the end of deformation is found. The relative radius of the annular punch ensuring equal stamping forces for the central and annular punches is determined.
High tensile alloy of copper to mitigate current collector deformation in silicon electrodes for lithium-ion batteries
The volumetric changes of silicon electrodes, along with the strong adhesive properties of certain binders, can lead to plastic deformation of the current collector and create damage in the electrode coating. Here, in this study, we report a detailed study of silicon coatings on a high-tensile alloy (HTA) foil of copper with strength over twice that of conventional copper foils. The HTA current collectors with high mechanical strength can mitigate plastic deformation upon continuous cycling. At moderate areal capacities (2.5–3 mAh cm −2 ), conventional copper foils show significant wrinkling after only a few electrochemical cycles, whereas the HTA foils remain intact. We demonstrate viability of the HTA foils in large format xx6395 pouch cells, in which the HTA current collectors remain intact even at an areal capacity of 4.5 mAh cm −2 ; in contrast, wrinkles form in conventional copper current collectors increasing the likelihood of lithium plating. Computational studies show that stresses generated during cycling of silicon electrodes are very high in the current collector and at the current collector-coating interface, explaining the wrinkling of conventional Cu foils. Our studies highlight importance of current collector to solve the electrochemical and chemo-mechanical performance challenges associated with high-loading silicon electrodes.
Origin, parameters, and underlying deformation mechanisms of propagating deformation bands in irradiated 316L stainless steel
Lüders-type propagating deformation bands were observed in specimens of irradiated 316L stainless steel samples removed from Spallation Neutron Source target vessels after service. Mechanical testing with digital image correlation (DIC) and in-situ tensile testing with scanning electron microscopy electron backscatter diffraction showed that the observed Lüders-type behavior was not related to the known transformation-induced plasticity or twinning-induced plasticity behavior. Instead, the phenomenon occurs at small local strain values before a significant amount of martensite or deformation twins appear in the microstructure. Microstructural analysis and in-situ mechanical test results suggest Lüders-type band formation and propagation were related to the appearance and evolution of defect-free channels—analogous to slip bands. A modified Swift equation with a Ludwigson-like component was offered to rationalize the phenomenon and model the strain-softening processes at small strain values. Finally, the results indicate complex microstructural processes and deformation mechanisms were active at small strain values and underline the benefits of advanced mechanical test approaches such as DIC.
Modeling Extreme Deformations in Lithium Ion Batteries
A simultaneously coupled modeling approach to study the electrochemical and thermal behavior of lithium-ion batteries under large mechanical deformation has been developed. The thermo-electrochemical pseudo-2D (P2D) battery model is coupled with a mechanical material model. Mechanical, thermal, and electrochemical models are implemented as user-defined sub-routines in the commercial multi-physics code LS-DYNA. The mechanical strain experienced by anode, cathode and separator results in thickness and porosity changes in each layer which in turn influences electrochemical behavior. The evolution of concentration profiles and cell potential are studied under different mechanical loading conditions. Internal short-circuits caused by mechanical deformation and corresponding physical behaviors are also elucidated. We discuss the competing effects of improved transport at higher temperature due to the internal short-circuit versus a drop in the effective ionic conductivity and electrolyte diffusivity due to mechanical deformation.
Single Crystal Plasticity Model with Deformation Twinning for the High Rate Deformation of β-HMX
Deformation twinning is an active deformation mechanism during loading along certain crystallographic directions of β-cyclotetramethylene tetranitramine (β-HMX). In this work, a finite strain thermomechanical model is extended to include twinning as a deformation mechanism in addition to plastic slip. The stress is derived from the free energy expression including a term representing the equation of state. The crystal plasticity framework is used to divide the total strain into inelastic and elastic component, where the elastic part is used in the expression for the free energy. The twin systems are treated as pseudo slip systems and the shear rate on the twin systems is evaluated in terms of the twin resistance and the projection of the stress tensor. The model parameters were calibrated against a set of plate impact experiments performed on β-HMX by Dick et al. The remaining plate impact experiments are used to evaluate the predictive capability of the model. The quality of the model fits and predictions is discussed from a physical and modeling perspective. Particularly, the role of twin modeling on results is highlighted. Finally, the model is used to explore the relationship between the propensity for twinning and crystal orientation.
The Pecora Escarpment (PCA) 91020 EL3 chondrite and deformation on theEL3 asteroid
Explore the source record for details and available documents.