Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cylinder liners”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Internal combustion engine with dual-channel cylinder liner cooling

A cylinder liner is provided that includes a cylinder bore capable of housing a piston, a top end having an annular flange, a first cylindrical section, a second cylindrical section, and an annular ridge that separates the first cylindrical section and the second cylindrical section. When employed in an a liner bore of an engine bock, the cylinder liner provides for two channels that allow for coolant to be supplied to the cylinder liner.

Chen, Allen Yao↗
DOE OSTI2024

High-modulus, high-strength, low alloy gray cast iron for cylinder liners and automotive applications

A high elastic modulus, high ultimate tensile strength, and low alloy gray cast iron for cylinder liners. The gray cast iron includes from 2.60 wt % to 3.30 wt % Carbon (C); from 1.50 wt % to 2.30 wt % Silicon (Si); from 0.30 wt % to 0.80 wt % Manganese (Mn); from 0.15 wt % to 0.35 wt % Phosphorus (P); from 0.05 wt % to 0.11 wt % Sulphur (S); from 0.60 wt % to 1.20 wt % Copper (Cu); from 0.10 wt % to 0.30 wt % Chromium (Cr); from greater than 0.0 wt % to 0.1 wt % Nickle (Ni); from 0.15 wt % to 0.40 wt % Molybdenum (Mo); and balance wt % Iron (Fe). The total wt % of Si, Mn, P, S, Cu, Cr, Ni, and Mo is less than about 4.10 wt %. The gray cast iron has a Carbon Equivalent (CE) from 3.00 wt % to 3.90 wt % and the product of Mn %*S % is from 0.025 to 0.045.

Yang, Jianghuai↗
DOE OSTI2019

Method of honing high-porosity cylinder liners

Methods of honing a surface are disclosed. The method may include spraying a coating having an initial average bulk porosity onto an engine bore wall and honing the coating to create an intermediate honed surface. The method may then include cleaning the intermediate honed surface and honing the intermediate honed surface with a cutting force of, for example, 110-130 kgf after the cleaning step. This may create a honed surface having an average porosity greater than the initial average bulk porosity. The methods may create a honed surface having a porosity that is more porous than the initially sprayed coating. The increased porosity of the honed surface may allow for increased oil retention in, for example, engine bores.

Maki, Clifford E.↗
NASA NTRS1997

Test Method Designed to Evaluate Cylinder Liner-Piston Ring Coatings for Advanced Heat Engines

Research on advanced heat engine concepts, such as the low-heat-rejection engine, have shown the potential for increased thermal efficiency, reduced emissions, lighter weight, simpler design, and longer life in comparison to current diesel engine designs. A major obstacle in the development of a functional advanced heat engine is overcoming the problems caused by the high combustion temperatures at the piston ring/cylinder liner interface, specifically at top ring reversal (TRR). Therefore, advanced cylinder liner and piston ring materials are needed that can survive under these extreme conditions. To address this need, researchers at the NASA Lewis Research Center have designed a tribological test method to help evaluate candidate piston ring and cylinder liner materials for advanced diesel engines.

Radil, Kevin C.↗
DOE OSTI2016

Review of laser produced multi-keV X-ray sources from metallic foils, cylinders with liner, and low density aerogels

Experimental results obtained within the last fifteen years on multi-keV X-ray sources irradiated with nanosecond scale pulse duration 3ω laser light at TW power levels by CEA and collaborators are discussed in this review paper. Experiments were carried out on OMEGA and GEKKO XII laser facilities where emitting materials in the 5–10 keV multi-keV energy range are intermediate Z value metals from titanium to germanium. Results focused on conversion efficiency improvement by a factor of 2 when an underdense plasma is created using a laser pre-pulse on a metallic foil, which is then heated by a second laser pulse delayed in time. Metal coated inner surface walls of plastic cylindrical tube ablated by laser beam impacts showed that plasma confinement doubles X-ray emission duration as it gives adequate plasma conditions (electron temperature and density) over a long period of time. Low-density aerogels (doped with metal atoms uniformly distributed throughout their volume or metal oxides) contained in a plastic cylinder have been developed and their results are comparable to gas targets. A hybrid target concept consisting of a thin metal foil placed at the end of a cylinder filled with low density aerogel has emerged as it could collect benefits from pre-exploded thin foils, efficient laser absorption in aerogel, and confinement by cylinder walls. All target geometry performances are relatively close together at a given photon energy and mainly depend on laser irradiation condition optimizations. Results are compared with gas target performances from recent NIF experiments allowing high electron temperatures over large dimension low density plasmas, which are the principal parameters for efficient multi-keV X-ray production.

Girard, Frédéric↗
DOE OSTI2022

System and method for control of compression in internal combustion engine via compression ratio and elastic piston

The present disclosure relates to a system for controlling ignition of an air/fuel mixture intake charge directed into an internal combustion engine. The system may have a longitudinally movable inner cylinder liner configured to fit within a cylinder wall portion of an internal combustion engine, and able to receive a piston of the engine therein. A portion of the inner cylinder liner defines an internal volume forming a combustion chamber, and the internal volume controls a compression ratio of the cylinder. The system also has a cylinder head assembly operatively associated with the inner cylinder liner and able to move linearly to cause longitudinal displacement of the inner cylinder liner relative to the cylinder wall portion. This enables the volume of the combustion chamber to be further varied, to thus further vary the compression ratio.

Flowers, Daniel L.↗
DOE OSTI2021

Cylinder cooling in opposed-piston engines

A cylinder assembly with a cylinder liner and a sleeve is provided that includes features that reduce coolant flow stagnation. The sleeve encloses a center section of the cylinder liner to form cooling channels that removes excess heat from the combustion area of the cylinder. The cylinder liner includes features for cooling between bridges in the cylinder's exhaust port.

Sahasrabudhe, Abhishek↗
NASA NTRS1983

Roller crosshead analysis

An analysis of the frictional behavior of a roller crosshead configuration is given. This configuration consists of a piston which carries at the wristpin position a roller of large diameter which can roll on the cylinder liner surfaces. A preliminary assessment is given of whether the roller can roll on the cylinder liner without skidding, and what, if any, are the tribological implications of this approach to a dry lubricated design. The rotational speed of the roller must change during the stroke if it is not to slip on the cylinder liner. The maximum value of angular acceleration occurs at top dead center and bottom dead center. If the traction force on the rim of the roller, which is the product of the normal force due to piston side load and the coefficient of friction, is not sufficient to drive the roller through the necessary angular acceleration, sliding will occur. At 1,000 rpm, it appears that there will be a definite area of slip near each end of the stroke. The length of the area of slip may be of the order of 1/8 inch at each of these points.

Wilcock, D.↗
NASA NTRS1995

Turbulator for a liner cooling jacket

A turbulator for a liner cooling jacket includes a metal panel which is suitable to be coiled into a generally cylindrical shape so as to be placed in a relief area between an engine cylinder block and a cylinder liner. The relief area may be machined into either the block or the cylinder liner and the metal panel is formed with a pattern of protuberances shaped like corrugations. In one embodiment, the corrugations have a shape similar to a sine wave and are arranged in a plurality of generally parallel axial segments. The corrugation wave pattern of one segment may be the same as its adjacent segment or may be staggered by one corrugation which would mean one-half of a full wave cycle. The corrugation pattern in the turbulator panel may be created by any one of various stamping or forming operations and when placed between the cylinder liner and block, increases turbulence of the cooling liquid in order to enhance heat transfer.

Hoag, Kevin L.↗
NASA NTRS1999

Development of Advanced In-Cylinder Components and Tribological Systems for Low Heat Rejection Diesel Engines

In-cylinder components and tribological system concepts were designed, fabricated and tested at conditions anticipated for a 55% thermal efficiency heavy duty diesel engine for the year 2000 and beyond. A Cummins L10 single cylinder research engine was used to evaluate a spherical joint piston and connecting rod with 19.3 MPa (2800 psi) peak cylinder pressure capability, a thermal fatigue resistant insulated cylinder head, radial combustion seal cylinder liners, a highly compliant steel top compression ring, a variable geometry turbocharger, and a microwave heated particulate trap. Components successfully demonstrated in the final test included spherical joint connecting rod with a fiber reinforced piston, high conformability steel top rings with wear resistant coatings, ceramic exhaust ports with strategic oil cooling and radial combustion seal cylinder liner with cooling jacket transfer fins. A Cummins 6B diesel was used to develop the analytical methods, materials, manufacturing technology and engine components for lighter weight diesel engines without sacrificing performance or durability. A 6B diesel engine was built and tested to calibrate analytical models for the aluminum cylinder head and aluminum block.

Yonushonis, T. M.↗
NASA NTRS1977

Estimating surface temperature in forced convection nucleate boiling: A simplified method

During a test program to investigate low-cycle thermal fatigue, 21 of 22 cylindrical test sections of a cylindrical rocket thrust chamber were thermally cycled to failure. Cylinder liners were fabricated from OFHC copper, Amzirc, and NARloy-Z. The cylinders were fabricated by milling cooling channels into the liner and closing out the backside with electrodeposited copper. The tests were conducted at a chamber pressure of 4.14 MN/sq m (600 psia) and an oxidant-fuel ratio of 6.0 using hydrogen-oxygen as propellants. The average throat heat flux was 54 MW/sq m (33 Btu/sq in./sec). All of the failures were characterized by a thinning of the cooling channel wall and eventual failure by tensile rupture. The 1/2-hard Amzirc material showed little improvement in cyclic life when compared with OFHC copper; while the NARloy-Z and aged Amzirc materials had the best cyclic life characteristics. One OFHC copper cylinder was thermall cycled 2044 times at a steady-state hot-gas-side wall temperature of 514 K (925 R) without failing.

Hendricks, R. C.↗
DOE OSTI2014

Replication of engine block cylinder bridge microstructure and mechanical properties with lab scale 319 Al alloy billet castings

In recent years, aluminum alloy gasoline engine blocks have in large part successfully replaced nodular cast iron engine blocks, resulting in improved vehicle fuel efficiency. However, because of the inadequate wear resistance properties of hypoeutectic Al–Si alloys, gray iron cylinder liners are required. These liners cause the development of large tensile residual stress along the cylinder bores and necessitate the maximization of mechanical properties in this region to prevent premature engine failure. The aim of this study was to replicate the engine cylinder bridge microstructure and mechanical properties following TSR treatment (which removes the sand binder to enable easy casting retrieval) using lab scale billet castings of the same alloy composition with varying cooling rates. Comparisons in microstructure between the engine block and the billet castings were carried out using optical and scanning electron microscopy, while mechanical properties were assessed using tensile testing. The results suggest that the microstructure at the top and middle of the engine block cylinder bridge was successfully replicated by the billet castings. However, the microstructure at the bottom of the cylinder was not completely replicated due to variations in secondary phase morphology and distribution. The successful replication of engine block microstructure will enable the future optimization of heat treatment parameters. - Highlights: • A method to replicate engine block microstructure was developed. • Billet castings will allow cost effective optimization of heat treatment process. • The replication of microstructure in the cylinder region was mostly successful. • Porosity was more clustered in the billet castings compared to the engine block. • Mechanical properties were lower in billet castings due to porosity and inclusions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Insulated exhaust port liner for a cylinder head assembly of a motor vehicle

An insulated exhaust port liner of a cylinder head assembly for fluidly connecting to an internal combustion engine of a motor vehicle includes a sealing layer. The sealing layer has a first surface defining a passage for fluidly connecting to the internal combustion engine and receiving exhaust gas. The sealing layer further includes a second surface opposite to the first surface. The liner further includes a thermal barrier layer coated onto the second surface of the sealing layer. The thermal barrier layer is a porous non-woven material for supporting the sealing layer on the cylinder head and reducing a transfer of heat from the sealing layer to the cylinder head.

Andruskiewicz, IV, Peter P.↗
NASA NTRS1984

Development of Gas-Lubricated Pistons for Heavy Duty Diesel Engine Technology Program

Static testing of a segmented, gas-lubricated, piston-ring was accomplished. The ring utilizes high-pressure gas generated during the diesel cycle to energize a hydrostatic gas film between the piston and cylinder liner. The configuration was deficient in overall performance, because all segments of a ring set failed to form a fluid-film simultaneously, when exposed to internal preload. The difficulty was traced to the moment balance required to prevent the segments from overturning and contacting the cylinder walls. Some individual sectors formed a film and performed well in every respect including load capability to 6,000 N. These results produce optimism as to the ultimate feasibility of hydrostatic, gas-lubricated piston rings. In addition to test results, the principles of operation, and theoretical developments are presented. Breathable liner concepts are suggested for future consideration. In these configurations, solid hydrostatic pistons are coupled with flexible liners that elastically deform to form a gas-film under hydrostatic pressurization. Breathable liners afford the mechanical simplicity required for mass produced engines, and initial examination indicates satisfactory operation.

Shapiro, W.↗
NASA NTRS1977

Experimental fatigue life investigation of cylindrical thrust chambers

Twenty-two cylindrical test sections of a cylindrical rocket thrust chamber were fabricated and 21 of them were cycled to failure to explore the failure mechanisms, determine the effects of wall temperature on cyclic life, and to rank the material life characteristics for comparison with results from isothermal tests of 12 alloys at 538 C. Cylinder liners were fabricated from OFHC copper, Amzirc, and NAR1loy-Z. Tests were conducted at a chamber pressure of 4.14 MW/sq m using hydrogen-oxygen propellants at an oxidant-fuel ratio of 6.0, which resulted in an average throat heat flux of 54 MW/sq m. The cylinders were cooled with liquid hydrogen at an average rate of 0.91 Kg/sec. All failures were characterized by a thinning of the cooling channel wall at the centerline and eventual failure by tensile rupture. Cyclic life rankings of the materials based on temperature do not agree with published rankings based on uniaxial, isothermal strain tests.

Quentmeyer, R. J.↗
DOE OSTI2017

A numerical investigation on methane combustion and emissions from a natural gas-diesel dual fuel engine using CFD model

Natural gas (NG)-diesel dual fuel engines have been criticized for their high emissions of unburned methane. The past research on methane emissions from dual fuel engines has focused on the measurement of methane concentration in exhaust gases. The development of approaches capable of minimizing methane emissions requests the detailed spatial distribution of methane in-cylinder during the combustion and post combustion processes. However, it is difficult to experimentally measure the spatial distribution of methane in-cylinder. Here this research presents a numerical study on the combustion process of a NG-diesel dual fuel engine using the computational fluids dynamics (CFD) model CONVERGE coupled with a reduced primary reference fuel (PRF) mechanism. The model was validated against the heat release process and the emissions of nitrogen oxide, methane and carbon monoxide measured in a single cylinder dual fuel engine. The validated CFD model was applied to investigate the combustion of methane and n-heptane and the spatial distribution of methane in the dual fuel engine. This is most likely the first attempt to visualize the spatial distribution of methane in dual fuel engines using CFD. The objective of this study is to numerically simulate the methane combustion process, especially the methane present outside the pilot spray, quantify the methane combustion in each combustion stage, and visualize the spatial methane distribution in cylinder. The results showed that the momentum produced by the pilot fuel injection and combustion pushed the combustion products of pilot fuel and methane within the pilot spray plume toward the unburned methane-air mixture. Such a movement enhanced the mixing of the hot combustion products and the relatively cold unburned methane-air mixture during the main combustion process and dominated the combustion of methane presented outside the pilot fuel spray plume. Based on the simulation results at a low load condition (4.05 bar), the main combustion process consumed 43–53% of the methane fumigated into the intake mixture. The post-combustion oxidation process consumed 17–29% of the intake methane, which was 36.2–51.8% methane that survived the main combustion process. In comparison, 27–35% methane emitted the engine without participating the combustion process. The unburned methane at exhaust valve opening was mainly observed at the center of the cylinder. In comparison, the contribution of the crevice and boundary layer around the cylinder liner to methane emissions was relatively small. The slip of methane through the dual fuel engines was due to the fact that the premixed mixture was too lean to support the propagation of the turbulent flame initiated by the pilot fuel and the lack of pilot fuel vapor reaching the center of the combustion chamber because of the geometric limitations of the fuel injection system and the reduced mass of pilot fuel injected into the cylinder. The approaches aiming to enhance the combustion of methane and minimize methane emissions from dual fuel engines should focus on those capable of increasing the volume of pilot fuel vapor formed after injected into the cylinder.

42 ENGINEERING↗
NASA NTRS1989

Sliding seal materials for low heat rejection engines

Sliding friction coefficients and wear rates of promising piston seal materials were measured under temperature, environmental, velocity, and loading conditions that are representative of the low heat rejection (LHR) diesel engine environment. These materials included carbides, oxides, and nitrides. In addition, silicon nitride and partially stablized zirconia disks (cylinder liners) were ion-implanted with TiNi, Ni, Co, and Cr, and subsequently run against carbide pins (piston rings), with the objective of producing reduced friction via solid lubrication at elevated temperature. Friction and wear measurements were obtained using pin-on-disk laboratory experiments and a unique engine friction test rig. Unmodified ceramic sliding couples were characterized at all temperatures by friction coefficients of 0.24 and above during the pin-on-disk tests. The coefficient at 800 C in an oxidizing environment was reduced to below 0.1, for certain material combination, by the ion-implantation of TiNi or Co. This beneficial effect was found to derive from the lubricious Ti, Ni, and Co oxides. Similar results were demonstrated on the engine friction test rig at lower temperatures. The structural integrity and feasibility of engine application with the most promising material combination were demonstrated during a 30-hour single-cylinder, direct-injection diesel engine test.

Beaty, Kevin↗