Engineering PapersSearch

SEARCH · Engineering Papers

Results for “critical load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

The scratch test - Different critical load determination techniques

Different critical load determination techniques such as microscopy, acoustic emission, normal, tangential, and lateral forces used for scratch test evaluation of complex or multilayer coatings are investigated. The applicability of the scratch test to newly developed coating techniques, systems, and applications is discussed. Among the methods based on the use of a physical measurement, acoustic emission detection is the most effective. The dynamics ratio between the signals below and above the critical load for the acoustic emission (much greater than 100) is well above that obtained with the normal, tangential, and lateral forces. The present commercial instruments are limited in load application performance. A scratch tester able to apply accurate loads as low as 0.01 N would probably overcome most of the actual limitations and would be expected to extend the scratch testing technique to different application fields such as optics and microelectronics.

Sekler, J.

Critical Load Exceedances for North America and Europe using an Ensemble of Models and an Investigation of Causes for Environmental Impact Estimate Variability: An AQMEII4 Study

Exceedances of critical loads for deposition of sulphur (S) and nitrogen (N) to different ecosystems were estimated using European and North American ensembles of air quality models, under Phase 4 of the Air Quality Model Evaluation International Initiative (AQMEII4), to identify where risk of ecosystem harm is expected to occur based on model deposition estimates. The ensembles were driven by common emissions and lateral boundary condition inputs. Model output was regridded to common North American and Europe 0.125° resolution domains, which were then used to calculate critical load exceedances. New, targeted deposition diagnostics implemented in AQMEII4 allowed an unprecedented level of post-simulation analysis to be carried out and facilitated the identification of specific causes of model-to-model variability in critical load exceedance estimates. New datasets for North American critical loads for acidity for forest soil water and aquatic ecosystems were combined with the ensemble deposition predictions to show a substantial decrease in the area and number of locations in exceedance between 2010 and 2016 (forest soils: 13.2 % to 6.1 %; aquatic ecosystems: 21.2 % to 11.4 %). All models agreed in the direction of the ensemble exceedance change between 2010 and 2016. The North American ensemble also predicted a decrease in both severity and total area in exceedance between the years 2010 and 2016 for eutrophication-impacted ecosystems in the USA (sensitive epiphytic lichen: 81.5 % to 75.8 %). The exceedances for herbaceous community richness also decreased between 2010 and 2016, from 13.9 % to 3.9 %. The uncertainty associated with the North American eutrophication results is high; there were sharp differences between the models in both predictions of total N deposition and the change in N deposition, and hence in the predicted eutrophication exceedances between the two years. The European ensemble was used to predict relatively static exceedances of critical loads with respect to acidification (4.48 % to 4.32 % from 2009 to 2010) while eutrophication exceedance increased slightly (60.2 % to 62.2 %). While most models showed the same changes in critical load exceedances as the ensemble between the two years, the spatial extent and magnitude of exceedances varied significantly between the models. The reasons for this variation were examined in detail by first ranking the relative contribution of different sources of sulphur and nitrogen deposition in terms of deposited mass and model-to-model variability in that deposited mass, followed by their analysis using AQMEII4 diagnostics, along with evaluation of the most recent literature. All models in both the North American and European ensembles had net annual negative biases with respect to observed wet deposition of sulphate, nitrate and ammonium. Diagnostics and recent literature suggest that this bias may stem from insufficient cloud scavenging of aerosols and gases, and may be improved through the incorporation of multiphase hydrometeor scavenging within the modelling frameworks. The inability of North American models to predict the timing of the seasonal peak in wet ammonium ion deposition (observed maximum was in April, while all models predicted a June maximum) may also relate to the need for multiphase hydrometeor scavenging (absence of snow scavenging in all models employed here). High variability in the relative importance of particulate sulphate, nitrate and ammonium deposition fluxes between models was linked to the use of updated particle dry deposition parameterizations in some models. However, recent literature and further development of some of the models within the ensemble suggests these particulate biases may also be ameliorated via the incorporation of multiphase hydrometeor scavenging. Annual sulphur and nitrogen deposition prediction variability was linked to SO 2 and HNO 3 dry deposition parameterizations, and diagnostic analysis showed that the cuticle and soil deposition pathways dominate the deposition mass flux of these species. Further work improving parameterizations for these deposition pathways should reduce variability in model acidifying gas deposition estimates. The absence of base cation chemistry in some models was shown to be a major factor in positive biases in fine mode particulate ammonium and particle nitrate concentrations. Models employing ammonia bidirectional fluxes had both the largest and the smallest magnitude biases, depending on the model and bidirectional flux algorithm employed. A careful analysis of bidirectional flux models suggests that those with poor NH 3 performance may underestimate the extent of NH 3 emissions fluxes from forested areas. Based on these results, an increased process-research focus is therefore recommended for the following model processes and on observations which may assist in model evaluation and improvement: multiphase hydrometeor scavenging combined with updated particle dry deposition, cuticle and soil deposition pathway algorithms for acidifying gases, base cation chemistry and emissions, and NH 3 bidirectional fluxes. Comparisons with satellite observations suggest that oceanic NH 3 emissions sources should be included in regional chemical transport models. The choice of land use database employed within any given model was shown to significantly influence deposition totals in several instances, and employing a common land use database across chemical transport models and critical load calculations is recommended for future work.

critical loads

Enhancing Distribution System Resilience: A First-Order Meta-RL Algorithm for Critical Load Restoration

The increasing frequency of extreme events and the integration of distributed energy resources (DERs) into modern grids have elevated the need for resilient and efficient critical load restoration strategies in distribution systems. However, the stochastic nature of renewable DERs, limited energy resource availability and the intricate nonlinearities inherent in complex grid control problem make the problem challenging. Although reinforcement learning (RL) and warm-start RL methods have shown promising results, their performance often falls short in rapidly adapting to new, unseen situations and typically requires exhaustive problem-specific tuning. To address these gaps, we propose a First-Order Meta-based RL (FOM-RL) algorithm within an online framework for adaptive and robust critical load restoration. By harnessing local DERs as the enabling technology, FOM-RL allows the RL agent to swiftly adapt to new unseen scenarios by leveraging previously acquired knowledge of different tasks. Experimental results provide evidence that proposed algorithm learns more efficiently and showcases generalization capabilities across diverse set of operational scenarios. Moreover, a rigorous theoretical analysis yields a tight sublinear regret bound, sensitive to temporal variability, with a task-averaged optimality gap bounded by O(VM+D*/(Tsquare root(M))). These results suggest that optimality improves with task similarity and an increased number of tasks M, reaffirming the efficacy and scalability of the proposed approach in addressing the complexities of critical load restoration in distribution systems.

complexity theory

An Ensemble Investigation of the Causes for Regional Air-Quality Model Critical Load Exceedances Prediction Variability in European and North American Domains Using Diagnostics From Phase 4 of the Air Quality Model Evaluation International Initiative

We summarize tentative findings from multi air quality model ensembles for the years 2009 and 2010 in Europe (EU), and 2010 and 2016 in North America (NA), under AQMEII-4. The model predictions of sulphur and nitrogen deposition were used to estimate exceedances of critical loads for acidification and eutrophication, to show the extent to which the ensemble members agree in the magnitude and the trend of ecologically meaningful impacts. Model exceedance variability was analyzed using AQMEII-4 diagnostics. Evaluation against concentration and wet deposition observations, coupled with these diagnostics, identified specific process representations as the causes for variability between model predictions and for reduced model performance. All models predicted reductions in ecosystem acidification impacts in North America between the years 2010 and 2016, in accord with SO2 emissions reduction legislation which started in 2010 (SO2 SIP) However, all models in EU and NA domains had net negative biases for wet deposition of sulphur and nitrogen relative to observations. The wet S deposition average mean bias for the NA ensemble was -0.17 eq ha-1 d-1, and for the EU ensemble -1.15 eq ha-1 d-1. The NA daily wet deposition average mean bias for NH4+ was -0.37 eq ha-1d-1; EU -1.19 eq ha-1 d-1. The daily NA wet NO3- deposition average mean bias was -0.24 eq ha-1d-1; EU -0.69 eq ha-1 d-1. The members of the ensemble diverged (factor of 10) in their North American predictions for Ndep and consequently their eutrophication exceedances. The models with the highest eutrophication predictions also predicted the highest levels of gas-phase ammonia dry deposition (standard deviation of ammonia dry deposition flux across ensemble members was larger than the ensemble average). These models also had negative biases of predicted ammonia concentrations; average mean biases of -0.63 (satellite NH3) and -0.85 ppbv (surface NH3) compared to ensemble averages of -0.30 and -0.34 ppbv. Diagnostics showed that these differences resulted from the manner in which bidirectional ammonia fluxes were parameterized within these models. The second largest source of NA eutrophication prediction variability were models with positive biases in particulate ammonium and nitrate concentrations, and higher particle nitrogen deposition levels ( particle ammonium concentration bias +0.35 ug m-3; ensemble bias +0.15 ug m-3). We believe two factors may have led to these latter overestimates: higher levels of fine mode particle nitrate formation compared to other models (due to the use of an inorganic heterogeneous chemistry algorithm which did not take base cation chemistry into account), and updates to particle dry deposition velocities carried out in the absence of concurrent updates to wet scavenging algorithms. The relative importance of dry gas, dry particulate, and wet deposition towards total sulphur and nitrogen deposition totals differed between EU and North American domains, though all models had negative biases in wet deposition as noted above. Parallel and subsequent work suggests that multiphase hydrometeor scavenging may improve model wet deposition performance. An increased research focus is recommended for four model processes: multiphase hydrometeor scavenging, ammonia bidirectional fluxes, base cation chemistry and emissions, and particle dry deposition.

regional air-quality model

Determination of the critical loads of shells by nondestructive methods

Two methods for determining the location of and load level to produce instability of compressed cylindrical shells are presented. The first relates the variation in the wall normal stiffness as a function of applied compressive force to the critical load. It uses the distribution of stiffness over the surface of the shell as a guide to buckle location. The second method associates the local dynamic mass with instability behavior. The test data presented show that either method will give excellent prediction capability from low-load-level data for shells of orthodox form. Neither method appears to apply to spirally stiffened shells. This is thought to be due to the fact that there is a substantial difference between the buckle pattern under axial compression and the imperfection shape induced by the normal displacement which is used to ascertain the wall stiffness and the dynamic mass.

Horton, W. H.

Effects of rotor location, coning, and tilt on critical loads in large wind turbines

Several large (1500 kW) horizontal rotor configurations were analyzed to determine the effects on dynamic loads of upwind downwind rotor locations, coned and radial blade positions, and tilted and horizontal rotor axis positions. Loads were calculated for a range of wind velocities at three locations in the structure: (1) the blade shank; (2) the hub shaft; and (3) the yaw drive. Blade axis coning and rotor axis tilt were found to have minor effects on loads. However, locating the rotor upwind of the tower significantly reduced loads at all locations analyzed.

Spera, D. A.

Effects of rotor location, coning, and tilt on critical loads in large wind turbines

Three large (1500 kW) horizontal rotor configurations were analyzed to determine the effects on dynamic loads of upwind and downwind rotor locations, coned and radial blade positions, and tilted and horizontal rotor axis positions. Loads were calculated for a range of wind velocities at three locations in the structure: the blade shank, the hub shaft, and the yaw drive. Blade axis coning and rotor axis tilt were found to have little effect on loads. However, locating the rotor upwind of the tower significantly reduced loads at all locations analyzed.

Spera, D. A.

A method of estimating the critical buckling load for structural members

The relations between load on the structure and rotation of a joint can be used to estimate the lowest critical load after the equation for neutral stability has been tested for three assumed critical loads, each of which is less than the lowest critical load. The solutions of six simple problems are included to illustrate the application of the method of estimating critical loads and to reveal certain characteristics of the method that should be known by the practical engineer using it. Four of these problems are concerned with members that lie in the elastic, or long-column, range. The other two problems are concerned with members that lie in the short-column range.

Lundquist, Eugene E

Buckling of Low Arches or Curved Beams of Small Curvature

A general solution, based on the classical buckling criterion, is given for the problem of buckling of low arches under a lateral loading acting toward the center of curvature. For a sinusoidal arch under sinusoidal loading, the critical load can be expressed exactly as a simple function of the beam dimension parameters. For other arch shapes and load distributions, approximate values of the critical load can be obtained by summing a few terms of a rapidly converging Fourier series. The effects of initial end thrust and axial and lateral elastic support are discussed. The buckling load based on energy criterion of Karman and Tsien is also calculated. Results for both the classical and the energy criteria are compared with experimental results.

Fung, Y C

The Critical Compression Load for a Universal Testing Machine When the Specimen Is Loaded Through Knife Edges

The results of a theoretical and experimental investigation to determine the critical compression load for a universal testing machine are presented for specimens loaded through knife edges. The critical load for the testing machine is the load at which one of the loading heads becomes laterally instable in relation to the other. For very short specimens the critical load was found to be less than the rated capacity given by the manufacturer for the machine. A load-length diagram is proposed for defining the safe limits of the test region for the machine. Although this report is particularly concerned with a universal testing machine of a certain type, the basic theory which led to the derivation of the general equation for the critical load, P (sub cr) = alpha L can be applied to any testing machine operated in compression where the specimen is loaded through knife edges. In this equation, L is the length of the specimen between knife edges and alpha is the force necessary to displace the upper end of the specimen unit horizontal distance relative to the lower end of the specimen in a direction normal to the knife edges through which the specimen is loaded.

Lundquist, Eugene E

The effect of ion plated silver and sliding friction on tensile stress-induced cracking in aluminum oxide

A Hertzian analysis of the effect of sliding friction on contact stresses in alumina is used to predict the critical load for crack generation. The results for uncoated alumina and alumina coated with ion plated silver are compared. Friction coefficient inputs to the analysis are determined experimentally with a scratch test instrument employing an 0.2 mm radius diamond stylus. A series of scratches were made at constant load increments on coated and uncoated flat alumina surfaces. Critical loads for cracking are detected by microscopic examination of cross sections of scratches made at various loads and friction coefficients. Acoustic emission (AE) and friction trends were also evaluated as experimental techniques for determining critical loads for cracking. Analytical predictions correlate well with micrographic evidence and with the lowest load at which AE is detected in multiple scratch tests. Friction/load trends are not good indicators of early crack formation. Lubrication with silver films reduced friction and thereby increased the critical load for crack initiation in agreement with analytical predictions.

Sliney, Harold E.

The effect of ion-plated silver and sliding friction on tensile stress-induced cracking in aluminum oxide

A Hertzian analysis of the effect of sliding friction on contact stresses in alumina is used to predict the critical load for crack generation. The results for uncoated alumina and alumina coated with ion plated silver are compared. Friction coefficient inputs to the analysis are determined experimentally with a scratch test instrument employing an 0.2 mm radius diamond stylus. A series of scratches were made at constant load increments on coated and uncoated flat alumina surfaces. Critical loads for cracking are detected by microscopic examination of cross sections of scratches made at various loads and friction coefficients. Acoustic emission (AE) and friction trends were also evaluated as experimental techniques for determining critical loads for cracking. Analytical predictions correlate well with micrographic evidence and with the lowest load at which AE is detected in multiple scratch tests. Friction/load trends are not good indicators of early crack formation. Lubrication with silver films reduced friction and thereby increased the critical load for crack initiation in agreement with analytical predictions.

Sliney, Harold E.

Effect of Assumed Damage and Location on the Delamination Onset Predictions for Skin-Stiffener Debonding

The difference in delamination onset predictions based on the type and location of the assumed initial damage are compared in a specimen consisting of a tapered flange laminate bonded to a skin laminate. From previous experimental work, the damage was identified to consist of a matrix crack in the top skin layer followed by a delamination between the top and second skin layer (+45 deg./-45 deg. interface). Two-dimensional finite elements analyses were performed for three different assumed flaws and the results show a considerable reduction in critical load if an initial delamination is assumed to be present, both under tension and bending loads. For a crack length corresponding to the peak in the strain energy release rate, the delamination onset load for an assumed initial flaw in the bondline is slightly higher than the critical load for delamination onset from an assumed skin matrix crack, both under tension and bending loads. As a result, assuming an initial flaw in the bondline is simpler while providing a critical load relatively close to the real case. For the configuration studied, a small delamination might form at a lower tension load than the critical load calculated for a 12.7 mm (0.5") delamination, but it would grow in a stable manner. For the bending case, assuming an initial flaw of 12.7 mm (0.5") is conservative, the crack would grow unstably.

Paris, Isabelle L.

Adhesion scratch testing - A round-robin experiment

Six sets of samples, TiN coated by chemical or physical vapor deposition methods (CVD or PVD) onto cemented carbide or high-speed steel (HSS), and TiC coated by CVD onto cemented carbide have been scratch tested using three types of commercially available scratch adhesion tester. With exception of one cemented carbide set, the reproducibility of the critical loads for any given set with a given stylus is excellent, about + or - 5 percent, and is about + or - 20 percent for different styli. Any differences in critical loads recorded for any given sample set can be attributed to the condition of the stylus (clean, new, etc.), the instrument used, the stylus itself (friction coefficient, etc.), and the sample set itself. One CVD set showed remarkably large differences in critical loads for different styli, which is thought to be related to a mechanical interaction between stylus and coating which is enhanced by a plastic deformability in the film related to the coating microstructure. The critical load for TiN on HSS increases with coating thickness, and differences in frictional conditions led to a systematic variation in the critical loads depending on the stylus used.

Perry, A. J.

The critical shear load of rectangular plates

This report gives formulas for analyzing the critical shear load of a simply supported square, isotropic (simple flat plate), or orthogonal anisotropic plate (a plate in which the rigidity in two directions perpendicular to each other is different, i.e. plywood or corrugated sheet), these formulas, although arrived at by approximation method, seem to agree fairly well with experimental results.

Seydel, Edgar