Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “crack damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Photoluminescence mapping of laser-damaged β-Ga 2 O 3

Here, photoluminescence (PL) mapping was utilized to investigate damage in β-Ga 2 O 3 epilayers induced by 1064 nm laser pulses. The intensity and position of the intrinsic UV band were determined and plotted as a false-color image. Two types of damage were identified: circular damage and damage cracks. Circular damage shows lower UV PL intensity than the surrounding material with color centers in a “halo” around the damaged region. Damage cracks are aligned with the a and c axes and show higher PL intensity than undamaged material. Defects in the as-grown material were revealed by shifts in the UV band energy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Millions of Small Pressure Cycles Drive Damage in Cracked Solar Cells

Here, we applied time-varying air pressure to a PV module containing newly cracked cells. The test used a new dynamic mechanical acceleration (DMX) apparatus. We applied pressure cycles similar to natural, wind-driven cycles. Compared to standard dynamic mechanical load (DML) tests, we applied much lower pressure (10 Pa to 300 Pa RMS) and many more cycles (one million at each of four pressure levels). We present a case study on a single cell in a commercial module. We monitored electrical continuity loss across cracks using electroluminescence (EL) imaging. 10 Pa pressure cycles caused negligible change. 30 Pa pressure cycles caused permanent damage that continued worsening even after tens of thousands of cycles. After one million 30 Pa cycles, a series of 100 Pa cycles still caused new, permanent damage to existing cracks. 300 Pa cycles caused further worsening and introduced new cracks.

14 SOLAR ENERGY↗
DOE OSTI2022

Performance of multifunctional piezoelectric energy harvesting microgyroscopes with material degradation

Most microelectromechanical systems (MEMS) are made from brittle materials that are prone to cracking. Damage from the formation of cracks can occur anytime during the manufacturing process or due to mechanical loading of MEMS devices. Cracks can increase the structures flexibility and lead to changes in performance or total failure. Understanding the potential influences cracks in MEMS is necessary for the longevity of these systems. The energy harvesting microgyroscope studied in this work is susceptible to crack propagation in its silicon substrate and lead zirconate titanate piezoelectric patch. To this end, an electromechanical model is developed to capture the impacts of cracks on the performance of a damaged energy harvesting microgyroscope. Numerical methods are used to approximate the damage associated with distributed crack networks. Then, the static and dynamic responses of the damaged microgyroscope are analyzed for two possible multifunctional setups. Here, the current study revealed that cracks can significantly affect the static and dynamic behaviors of the microgyroscope energy harvester. Combinations of cracking and piezoelectric property degradation cause a decrease in the static pull-in voltage and shift the resonance frequencies of the system. Additionally, it is shown that the systems sensitivity to changes in the base rotation and energy harvesting capabilities vary widely depending on the severity of material degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Miniature Crack or Damage Detection on Cable Insulation and Jacket Using Conformal Surface Wave Reflectometry

This letter introduces the study and application of a conformal surface wave launcher array to detect miniature insulation and/or jacket damage on unshielded cables. Here simulation and experimental results are presented that demonstrate that with the proposed concept very small instances of damage at various distances along power cables can be detected. Effects of damage detection feasibility in the presence of other cables in proximity and for cables containing semiconducting screen are also presented.

42 ENGINEERING↗
DOE OSTI2022

In situ detection and characterization of alkali-silica reaction damage in concrete using contactless ultrasonic wavefield imaging

Here we present work to characterize cracking damage in concrete caused by alkali-silica reactivity distress. We apply contactless ultrasonic scan inspection, exploiting Rayleigh wave scattering from concrete inhomogeneities. The scanning system utilizes a multi-channel MEMS sensor array to collect ultrasonic wavefield data from concrete subjected to ASR-promoting environments. The location and extent of ASR damage are established by internal expansion measurements from embedded strain gauges, scanning electron microscope images of cored samples, and expansion measurements from companion samples. A wavefield data processing method extracts oscillatory fields from the ultrasonic wavefield data to detect distinct zones of ASR damage. A damage index is proposed to further characterize the extent of ASR damage. The results confirm the feasibility and accuracy of the approach to characterize ASR damage in concrete. The fully contactless ultrasonic scanning measurement system does not require separate material samples and enables in situ characterization of ASR damage within concrete structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Micromechanics of Fracture Propagation During Multistage Stress Relaxation and Creep in Brittle Rocks

Time-dependent rock deformation caused by the initiation and growth of fractures leads to the weakening of the rock mass. Understanding the fracturing mechanisms involved in the time-dependent behavior in brittle rocks is very important and to achieve this goal, a systematic series of three types of experiments was performed on double-flawed prismatic Barre granite specimens under unconfined compression. The first series aimed to identify the failure mechanism in the short-term failure mode under monotonic loading, the, second series involved multistage relaxation (constant strain) experiments to analyze the damage at different strain levels, and the third series explored the fracture propagation under multistage creep (constant load) experiments. The spatial and temporal evolution of cracking mechanisms were evaluated using the acoustic emission (AE) and two-dimensional digital image correlation (2D-DIC) techniques to observe the whole crack growth process as well as the accumulated inelastic strain at the specified region of interest. Results suggest that in the case of multistage creep experiments, the time to failure was less compared to the multistage relaxation, when loaded above the crack damage threshold (CD) estimated from the monotonic testing. Furthermore, the frequency magnitude distribution of the AE events generated in the three loading conditions followed the Gutenberg Richter model. A relatively lower b-value was obtained for the creep experiments, indicative of high energy AE events and faster crack growth. In addition, the AE and DIC results also revealed high evolution of tensile cracks at-different stages of creep and relaxation compared to shear and mixed-mode cracks.

58 GEOSCIENCES↗
DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modeling detonation with CartaBlanca simulations

The accurate modeling of high explosive (HE) detonation and the con- sequent large solid deformation, failure, plastic flow, porosity growth, and shock wave propagation is important because simulations can capture spatial and temporal features that experimental diagnostics cannot capture. However, the simulation of the explosive event poses challenges to a computational scientist. These include the accurate modeling of ductile damage, crack formation, plastic deformation, as well as physical and nu- merical instabilities. The material response can be history-dependent and subject to large material deformation. Our research simulates the impact of a high explosive (Detasheet) onto a tantulum metal plate. We performed the simulations using CartaBlanca at different mesh resolutions. We decided the study would be impactful if we perform the simulations with the Material Point Method. Differences were observed at the different mesh resolutions in velocity and nodal stress magnitude, so increased mesh resolutions may be required. In addition, the Discontinuous Galerkin method would be needed to account for the large gas expansion.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Design, Fabrication and On-Sun Performance Evaluation of SiC Receiver Feature Specimens for CST Applications Using Additively Manufactured SiC Materials

Increasing operating temperatures of solar receivers is paramount to the efficiency of concentrated solar thermal (CST) and solar power (CSP) systems. Successful development of CST systems to generate heat for industrial applications requires significant increase in temperature capability and techno-economically viability of the receiver systems. Supported by an award from the Solar Technology Office (SETO), US Department of Energy (DOE), GE Aerospace Research in collaboration with Heliogen Holdings Inc and Sandia National Lab, is engaged in the development of ultra-High Operating Temperature SiC-matrix Solar Thermal Air Receiver (HOTSSTAR) enabled by additive manufacturing. The program objective is to demonstrate SiC receiver with air exit temperatures up to 1100 oC and high thermal efficiencies. We report design, fabrication and on-sun test results of SiC components of a prototype 50kW (thermal) HOTSSTAR module. The receiver module architecture is based on a radial airflow design and consists of a series of radial SiC receiver sectors organized around a SiC center absorber. The SiC components are fabricated using binder-jet printed SiC followed by melt-infiltration reaction bonding process. To enhance the reliability and to minimize the risk of cracking damage of SiC test articles in thermal gradient and thermal shock environment of the application, the components were laminated with GE’s MI SiC-SiC CMC. Following extensive design and lab test analyses, selected SiC component designs are tested at Heliogen Lancaster Solar field under highly concentrated solar fluxes around 2000 suns to assess the thermal performance characteristics under realistic field conditions. We report on the test results and compare the thermal performances of different HOTSSTAR SiC absorbers. Finally, we discuss fabrication and initial assembly of a 50kW prototype test module in preparation of on-sun field tests to assess the performance of our final design.

CST, CSP, high temperature, air receiver, SiC, add↗
DOE OSTI2022

Effect of Water Chemistry on Crack Growth Rate in Neutron Irradiated X-750 and XM-19

The Advanced Test Reactor (ATR) National Science User Facility (NSUF) was used to study the effect of neutron damage on crack growth rates (CGR) under simulated boiling water reactor (BWR) water chemistry conditions using a fast neutron spectrum to accelerate the damage process. Nickel based Alloy X-750 and XM-19 were irradiated in the ATR center flux trap (CFT), with this experiment marking the first civilian project to utilize this position within the reactor. 0.4T-CT specimens were used to study crack growth rates for two sample fluences (~1.9 x 1020 n/cm2 and ~9.5 x 1020 n/cm2, E > 1MeV)) in both normal water chemistry (NWC) at 2.5 ppm O2 and hydrogen water chemistry (HWC) at ~80 ppb H2. CGR testing was conducted at a temperature of 288 °C. A decrease in CGR was observed for both alloys with the average ratio (CGR in NWC/CGR in HWC) being a factor of 281 for the XM-19 samples and a factor of 27.8 for the X-750 samples. Observed CGRs in this study showed little difference compared to non-irradiated samples (the non-irradiated XM-19 was 20% cold worked), suggesting limited sensitivity of these susceptible alloys to irradiation effects. Detailed results of CGR response to varying environmental electrochemical potential (ECP) and water purity will be presented in the context of crack growth mitigation in different water chemistries and the change in material behavior relative to non-irradiated samples of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Water Chemistry on Crack Growth Rates in Neutron Irradiated X-750 and XM-19

The Advanced Test Reactor (ATR) National Science User Facility (NSUF) was used to study the effect of neutron damage on crack growth rates (CGR) under simulated boiling water reactor (BWR) water chemistry conditions using a fast neutron spectrum to accelerate the damage process. Nickel based Alloy X-750 and XM-19 were irradiated in the ATR center flux trap (CFT), with this experiment marking the first civilian project to utilize this position within the reactor. 0.4T-CT specimens were used to study crack growth rates for two sample fluences (~1.9 x 1020 n/cm2 and ~9.5 x 1020 n/cm2, E > 1MeV) in both normal water chemistry (NWC) at 2.5 ppm O2 and hydrogen water chemistry (HWC) at ~80 ppb H2. A decrease in CGR was observed with HWC for both alloys with the average ratio (CGR in NWC/CGR in HWC) being a factor of 281 for the XM-19 samples and a factor of 27.8 for the X-750 samples. Observed CGRs in this study showed little difference compared to non-irradiated samples (the non-irradiated XM-19 was 20% cold worked), suggesting limited sensitivity of these susceptible alloys to irradiation effects. The CGR response to varying environmental electrochemical potential (ECP) and water purity will be presented.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Leveraging a Neural Network-Enhanced Reproducing Kernel Particle Method for Multiphysics Degradation Modeling of Energy Storage Materials

Energy storage materials exhibit strong electro-chemo-mechanical coupling and highly anisotropic material properties, contributing to the formation and propagation of micro-cracking during charge/discharge cycling and resulting in reduced performance and service life. A coupled electro-chemo-mechanical reproducing kernel particle method (RKPM) formulation has been developed to analyze this system. With microstructural images supplied by the National Renewable Energy Laboratory (NREL), pixel-based model construction by RKPM is used to represent the complex material microstructures that dictate the coupled physics of these systems. Traditional electro-chemo-mechanical models rely on mesh-based finite element methods, which can lead to difficulties in meshing such complex geometries and capturing crack propagation due to mesh dependency. Here, a neural network-enhanced reproducing kernel particle method (NN-RKPM) [1, 2] is introduced to effectively model damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. NN-RKPM is additionally used to inform how crack opening and closure in turn affect the coupled chemical equations and material microstructure. Reference: [1] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, pp 4422-4454, https://doi.org/10.1002/nme.7040, 2022. [2] Baek, J., Chen, J. S., "A Neural Network-Based Enrichment of Reproducing Kernel Approximation for Modeling Brittle Fracture", Computer Methods in Applied Mechanics and Engineering Vol. 410, 116590, 2024.

degradation↗
DOE OSTI2022

Long Term Damage Testing (NREL)

DOE's Regional Test Center program has fielded several strings of PV modules as part of their Long Term Testing program. Some of these modules have been installed since 2016 and have been exposed to severe weather events. A key to developing long lifespans for PV modules (in excess of 30 years) is understanding how damage and defects develop, propagate and progress. Researchers at the NREL Regional Test Center have started developing testing procedures and analysis tools in order to characterize modules in a controlled manner with the goal of understanding how damage spreads under normal operations. Characterization methods include EL and IR imaging, outdoor and indoor IV curves, and long term exposure monitoring. Modules to be evaluated will be chosen based on severity of defect, ability to track changes in defect and space requirements. The samples will be loaded at maximum power using grid-tied inverters or other means. Gathering and reporting on this data may help engineers and scientists design for damage and improve long-term performance.

crack damage↗
DOE OSTI2025

A novel peridynamics-based approach to predict pharmaceutical tablet robustness

The pharmaceutical drug product development process can be greatly accelerated through the use of modeling and simulation techniques to predict the manufacturability and performance of a given formulation. The anticipation and possible mitigation of tablet damage due to manufacturing stresses represents a specific area of interest in the pharmaceutical industry for predicting formulation and tableting performance. While the finite element method (FEM) has been extensively used for predicting the mechanical behavior of powder material in the compaction processes, a shortcoming of the approach is the inherent difficulty to predict discontinuities (e.g., damage or cracking) within a tablet as FEM is a continuum-based approach. In this work, we propose a novel method utilizing peridynamics (PD), a numerical method that can capture discontinuities such as tablet fracture, to predict the evolution of damage and breakage in pharmaceutical tablets. The approach links (1) the finite element method – to elucidate the behavior of powders during die compaction – with (2) the peridynamics modeling technique – to model the discontinuous nature of damage and predict tablet breakage during the critical stages of unloading and ejection from the compression die. This short communication presents a proof of concept including a workflow to calibrate the linked FEM-PD simulation models. Further, it demonstrates promising results from a preliminary experimental validation of the approach. Following further development, this approach could be used to guide the optimization of compression processes through targeted changes to formulation material properties, compression process conditions, and/or tooling geometries to deliver improved process efficiency and tablet robustness.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Damage tolerance in the graphite cores of UK power reactors and implications for new build

The United Kingdom has been operating graphite-moderated gas-cooled commercial nuclear power reactors for more than 60 years. Both Generation I Magnox reactors and Generation II Advanced Gas-cooled Reactors have operated beyond their nominal design lifetimes and the safety cases for continued operation have had to address the issue of damage tolerance of the graphite cores. This review describes the designs of the reactors and the methodologies employed for their assessment. Emerging issues arising from extended operation and ageing of the cores are discussed together with the evolution of assessment methodologies to address predicted and observed damage. The UK nuclear regulator perspective is summarised and some conclusions are drawn on the implications for new build.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Multiphysics Meshfree Degradation Modeling of Energy Storage Materials with Kernel Enrichment

Energy storage materials exhibit strong electro-chemo-mechanical coupling and highly anisotropic material properties, contributing to the formation and propagation of micro-cracking during charge/discharge cycling and ultimately diminishing performance and service life. With microstructural images supplied by the National Renewable Energy Laboratory (NREL), pixel-based meshfree model construction by the reproducing kernel particle method (RKPM) is used to represent the complex material microstructures that dictate the coupled physics of these systems. Traditional electro-chemo-mechanical models rely on mesh-based finite element methods, which can lead to difficulties in meshing such complex geometries and capturing crack propagation due to mesh dependency. The first kernel enrichment discussed will be the interface modified reproducing kernel (IM-RK) [1, 2], constructed by scaling a smooth kernel function with an interface-distance function to achieve strategic discontinuity types (i.e. weak discontinuities for strain discontinuities and strong discontinuities for cracks) and alleviate Gibbs oscillations near these transition zones. The IM-RK is especially useful for areas in which a known discontinuity-type is expected a priori. The second kernel enrichment to be discussed is a neural network-enhanced reproducing kernel (NN-RK) [3, 4], which is introduced to effectively model non-obvious damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. NN-RK is additionally used to inform how crack opening and closure in turn affect the electro-chemo-mechanical responses in the material microstructure. Reference: [1] Wang, Y., Baek, J., Tang, Y. et al. "Support vector machine guided reproducing kernel particle method for image-based modeling of microstructures," Comput Mech 73, 907-942 (2024). https://doi.org/10.1007/s00466-023-02394-9. [2] Susuki, K., Allen, J. & Chen, J. S.. "Image-based modeling of coupled electro-chemo-mechanical behavior of Li-ion battery cathode using an interface-modified reproducing kernel particle method," Engineering with Computers (2024). https://doi.org/10.1007/s00366-024-02016-9. [3] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, 4422-4454 (2022). https://doi.org/10.1002/nme.7040.

25 ENERGY STORAGE↗
DOE OSTI2026

Kernel Enriched Meshfree Multiphysics Degradation Modeling of Energy Storage Materials

Energy storage materials exhibit strong electro-chemo-mechanical coupling and highly anisotropic material properties, contributing to the formation and propagation of micro-cracking during charge/discharge cycling and ultimately diminishing performance and service life. With microstructural images supplied by the National Laboratory of the Rockies (NLR), pixel-based meshfree model construction by the reproducing kernel particle method (RKPM) is used to represent the complex material microstructures that dictate the coupled physics of these systems. Traditional electro-chemo-mechanical models rely on mesh-based finite element methods, which can lead to difficulties in meshing such complex geometries and capturing crack propagation due to mesh dependency. The first kernel enrichment discussed will be the interface modified reproducing kernel (IM-RK) [1, 2], constructed by scaling a smooth kernel function with an interface-distance function to achieve strategic discontinuity types (i.e. weak discontinuities for strain discontinuities and strong discontinuities for cracks) and alleviate Gibbs oscillations near these transition zones. The IM-RK is especially useful for areas in which a known discontinuity-type is expected a priori. The second kernel enrichment to be discussed is a neural network-enhanced reproducing kernel (NN-RK) [3, 4], which is introduced to effectively model non-obvious damage and crack propagation in the material microstructures; the location, orientation, and solution transition near a localization are automatically captured by superimposed block-level NN optimizations. This NN enrichment approach allows for effective modeling of localizations via a fixed background discretization, relieving tedious efforts for adaptive refinement in traditional mesh-based methods. Applications to the heterogeneous microstructures of Li-ion battery cathodes will be presented to demonstrate the effectiveness of the proposed methods. NN-RK is additionally used to inform how crack opening and closure in turn affect the electro-chemo-mechanical responses in the material microstructure. References: [1] Wang, Y., Baek, J., Tang, Y. et al. "Support vector machine guided reproducing kernel particle method for image-based modeling of microstructures," Comput Mech 73, 907-942 (2024). https://doi.org/10.1007/s00466-023-02394-9. [2] Susuki, K., Allen, J. & Chen, J. S.. "Image-based modeling of coupled electro-chemo-mechanical behavior of Li-ion battery cathode using an interface-modified reproducing kernel particle method," Engineering with Computers (2024). https://doi.org/10.1007/s00366-024-02016-9. [3] Baek, J., Chen, J. S., Susuki, K., "Neural Network enhanced Reproducing Kernel Particle Method for Modeling Localizations," International Journal for Numerical Methods in Engineering, Vol. 123, 4422-4454 (2022). https://doi.org/10.1002/nme.7040.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

A mean field homogenization model for the mechanical response of ceramic matrix composites

SiC/SiC composites offer exceptional mechanical stability at high temperatures and under irradiation. These ceramic matrix composites are therefore strong candidate materials for future nuclear energy applications. Their mechanical response, which exhibits pseudo-plasticity, is mediated by matrix cracking, fiber debonding, and fiber pull-out due to slip. Here, this study introduces a mechanistic model for the behavior of unidirectionally reinforced SiC/SiC composites. Specifically a mean field homogenization approach is proposed to account for all deformation and degradation modes during mechanical deformation. The homogenization scheme relies on a Mori Tanaka method that is extended to consider the effects of the coating’s elasto-plastic response on the development of micromechanical fields. Further, the model proposed introduces a method to effectively account for the role of localized damage (i.e., cracks) on mechanical fields within both the fiber and the matrix. Upon validating the model against experimental data, the roles of interface sliding, coating dimensions and intrinsic elastic response, as well as of microstructure (e.g. porosity, fiber volume fraction) are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗