Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “controlled stiffness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Design and Testing of a Dynamically-Tuned Magnetostrictive Spring with Electrically-Controlled Stiffness

This paper details the development of an electrically-controlled, variable-stiffness spring based on magnetostrictive materials. The device, termed a magnetostrictive Varispring, can be applied as a semi-active vibration isolator or switched stiffness vibration controller for reducing transmitted vibrations. The Varispring is designed using 1D linear models that consider the coupled electrical response, mechanically-induced magnetic diffusion, and the effect of internal mass on dynamic stiffness. Modeling results illustrate that a Terfenol-D-based Varispring has a rise time almost an order of magnitude smaller and a magnetic diffusion cut-off frequency over two orders of magnitude greater than a Galfenol-based Varispring. The results motivate the use of laminated Terfenol-D rods for a greater stiffness tuning range and increased bandwidth. The behavior of a prototype Varispring is examined under vibratory excitation up to 6 MPa and 25 Hz using a dynamic load frame. For this prototype, stiffness is indirectly varied by controlling the excitation current. Preliminary measurements of continuous stiffness tuning via sinusoidal currents up to 1 kHz are presented. The measurements demonstrate that the Young's modulus of the Terfenol-D rod inside the Varispring can be continuously varied by up to 21.9 GPa. The observed stiffness tuning range is relatively constant up to 500 Hz, but significantly decreases thereafter. The stiffness tuning range can be greatly increased by improving the current and force control such that a more consistent current can be applied and the Varispring can be accurately tested at a more optimal bias stress.

Vibration control↗
NASA NTRS1985

Parametric Stiffness Control of Flexible Structures

An unconventional method for control of flexible space structures using feedback control of certain elements of the stiffness matrix is discussed. The advantage of using this method of configuration control is that it can be accomplished in practical structures by changing the initial stress state in the structure. The initial stress state can be controlled hydraulically or by cables. The method leads, however, to nonlinear control equations. In particular, a long slender truss structure under cable induced initial compression is examined. both analytical and numerical analyses are presented. Nonlinear analysis using center manifold theory and normal form theory is used to determine criteria on the nonlinear control gains for stable or unstable operation. The analysis is made possible by the use of the exact computer algebra system MACSYMA.

Moon, F. C.↗
NASA NTRS1989

Magnetic bearing stiffness control using frequency band filtering

Active magnetic bearings can be implemented with frequency band-reject filtering that decreases the bearing stiffness and damping at a small bandwidth around a chosen frequency. The control scheme was used for reducing a rotor dynamic force, such as an imbalance force, transmitted to the bearing stator. The scheme creates additional system vibration modes at the same frequency. It also shows that the amount of force reduction is limited by the stability requirement of these modes.

Chen, H. Ming↗
DOE OSTI2022

Fibrous anisotropy and mineral gradients within the radula stylus of chiton: Controlled stiffness and damage tolerance in a flexible biological composite

Over hundreds of millions of years, organisms have evolved architected structures via precise control over hierarchically assembled components, including the integration of dissimilar materials. One such example is found in the radula system of chitons, intertidal mollusks that feed on algae growing on the rock. Their radula consists of multiple rows of ultrahard teeth, each integrated with a foldable belt-like substrate via a stiff, yet flexible stylus, which is essential for efficient rasping during the feeding process. Here, we investigate the nano and micro-scale components and architectures as well as regional mechanical properties of the stylus, and their subsequent role during the rasping of Cryptochiton stelleri. Three important factors were determined to contribute to the regio-specific stiffness of the stylus: the presence of mineral components, highly oriented chitinous fibers, and a chemically cross-linked protein matrix. All these factors are varied throughout the stylus. There is a high mineral content on the trailing edge close to the tooth and a cross-linked matrix on the leading edge, both with orientational specific oriented chitin fibers that provide force transduction to the tooth. Conversely, there is a significant lack of mineral or cross-linked matrix in the proximal end as well as a low degree of fiber orientation, resulting in a flexible region that can accommodate torsion and flexure during rasping. Understanding the graded composite structure of the stylus and applying this unique design to various engineering fields such as soft robotics, biotechnology, and the medical industry, can inspire the production of high-performance materials.

Lee, Jung-Eun↗
NASA NTRS1984

Response of large space structures with stiffness control

For large space structures, such as the 100-meter-diameter wrap-rib deployable antenna and spinning solar sail, whose out-of-plane stiffness is derived from in-plane tension, the out-of-plane motion can be actively controlled by time-varying in-plane tension. An elastic string is used to demonstrate the proposed approach, which results in a nonlinear ordinary differential equation. An approximation method is outlined from which the magnitude of time-varying tension can be determined based on the efficiency factor, the time factor or the optimal factor.

Chen, J.-C.↗
NASA NTRS1985

Stiffness Control of Large Space Structures

A technique for using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. The method is applied to a low order system. Selective modal damping is achieved. The actuators used in this method may be electrically powered. The method is suitable for structures which are too slender or flimsy to permit the use of reaction jet-type actuators.

Fanson, J. L.↗
NASA NTRS1985

Stiffness control of large space structures

A method of using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. The technique is applied to a vibrating string and to a low order system. Response feedback control for the vibrating string and selected modal control are used for achieving the modal damping. The actuators may be electrically powered and are suitable for structures with extremely low rigidity.

Chen, J. C.↗
NASA NTRS1985

Stiffness control of large space structures

A method of using internal force producing dual element/actuators for vibration suppression of large space structures is proposed. This technique is applied to a vibrating string as well as a low order system. Response feedback control for the vibrating string and selected modal control are used for achieving the modal damping. The actuators used in this method may be electrically powered and are suitable for structures with extremely low rigidity.

Chen, J.-C.↗
NASA NTRS1987

Vibration suppression by stiffness control

The feasibility of using piezoelectric ceramics as both sensors and actuators for vibration suppression in a lightweight, flimsy structure was demonstrated. Multimode control was achieved using one sensor and actuator pair. The Positive Position Feedback control strategy requires only knowledge of the natural frequencies of the structure. Implementation of the Positive Position Feedback used only strain measurements to achieve damping, no velocities, or acceleration are needed. All spillover is stabilizing for sufficient small gains.

Fanson, James↗
NASA NTRS2010

Applied Joint-Space Torque and Stiffness Control of Tendon-Driven Fingers

Existing tendon-driven fingers have applied force control through independent tension controllers on each tendon, i.e. in the tendon-space. The coupled kinematics of the tendons, however, cause such controllers to exhibit a transient coupling in their response. This problem can be resolved by alternatively framing the controllers in the joint-space of the manipulator. This work presents a joint-space torque control law that demonstrates both a decoupled and significantly faster response than an equivalent tendon-space formulation. The law also demonstrates greater speed and robustness than comparable PI controllers. In addition, a tension distribution algorithm is presented here to allocate forces from the joints to the tendons. It allocates the tensions so that they satisfy both an upper and lower bound, and it does so without requiring linear programming or open-ended iterations. The control law and tension distribution algorithm are implemented on the robotic hand of Robonaut-2.

Abdallah, Muhammad E.↗
DOE OSTI2022

Control of Surface Chemical Reactions through Solid Stiffness

Control of surface reactions is commonly achieved by modification of surface electronic structures. Here, we discover an alternative pathway for controlling surface reactions by tuning the mechanical stiffness of the underlying material. We find that in addition to the typically assumed surface electronic contribution right at the reactive site, the contribution from the deformation of the bulk region plays a vital role in controlling surface reactions. The underlying mechanism is an elastic relaxation of the solid, which depends on the material’s stiffness and can be modified by tuning bulk stoichiometry. The effect of bulk stiffness on surface reactions has been demonstrated by considering hydrogen scission reaction and oxygen incorporation reaction during corrosion of amorphous SiC in water and air, respectively. Finally, our results imply that tuning of bulk stiffness by modifying stoichiometry can provide an effective method for controlling surface reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2016

Vibration Control via Stiffness Switching of Magnetostrictive Transducers

In this paper, a computational study is presented of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magneto-mechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.13; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping. For the cases considered, optimal resistive shunt damping performed considerably better than both voltage- and shunt-controlled stiffness switching.

vibration control↗
NASA NTRS2016

Vibration Control via Stiffness Switching of Magnetostrictive Transducers

This paper presents a computational study of structural vibration control that is realized by switching a magnetostrictive transducer between high and low stiffness states. Switching is accomplished by either changing the applied magnetic field with a voltage excitation or changing the shunt impedance on the transducer's coil (i.e., the magnetostrictive material's magnetic boundary condition). Switched-stiffness vibration control is simulated using a lumped mass supported by a damper and the magnetostrictive transducer (mount), which is represented by a nonlinear, electromechanical model. Free vibration of the mass is calculated while varying the mount's stiffness according to a reference switched-stiffness vibration control law. The results reveal that switching the magnetic field produces the desired change in stiffness, but also an undesired actuation force that can significantly degrade the vibration control. Hence, a modified switched-stiffness control law that accounts for the actuation force is proposed and implemented for voltage-controlled stiffness switching. The influence of the magnetomechanical bias condition is also discussed. Voltage-controlled stiffness switching is found to introduce damping equivalent to a viscous damping factor up to about 0.25; this is shown to primarily result from active vibration reduction caused by the actuation force. The merit of magnetostrictive switched-stiffness vibration control is then quantified by comparing the results of voltage- and shunt-controlled stiffness switching to the performance of optimal magnetostrictive shunt damping.

stiffness tuning↗