Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conducting structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Scattering from thin dielectric straps surrounding a perfectly conducting structure

A method to calculate the electromagnetic scattered fields from a dielectric strap wrapped around convex, conducting structure is presented. A moment method technique is used to find the current excited within the strap by the incident plane wave. Then, Uniform Geometrical Theory of Diffraction (UTD) is used to compute the fields scattered by the strap. Reasonable agreement was obtained between the computed and the measured results. The results found in this study are useful in evaluating straps as a target support structure for scattering measurements.

Al-Hekail, Zeyad↗
NASA NTRS1993

Scattering from thin dielectric straps surrounding a perfectly conducting structure

Dielectric straps can support very heavy targets and have low backscattering levels, especially at low frequencies (below 8 GHz); thus, they can be used effectively to support targets during backscattered field measurements. In this paper, the scattered fields of nonmagnetic dielectric straps surrounding a perfectly conducting structure are presented, and the computed results are compared with experimental data. Empirical formulas for the strap scattered fields are also given. These formulas are good for general convex structures whose radii of curvature are large compared with the wavelength and are expected to give a reasonable estimate of the true backscattered fields from the dielectric straps when used as a target support structure.

Al-Hekail, Zeyad O.↗
NASA NTRS2002

Initial Mechanical Testing of Superalloy Lattice Block Structures Conducted

The first mechanical tests of superalloy lattice block structures produced promising results for this exciting new lightweight material system. The testing was performed in-house at NASA Glenn Research Center's Structural Benchmark Test Facility, where small subelement-sized compression and beam specimens were loaded to observe elastic and plastic behavior, component strength levels, and fatigue resistance for hundreds of thousands of load cycles. Current lattice block construction produces a flat panel composed of thin ligaments arranged in a three-dimensional triangulated trusslike structure. Investment casting of lattice block panels has been developed and greatly expands opportunities for using this unique architecture in today's high-performance structures. In addition, advances made in NASA's Ultra-Efficient Engine Technology Program have extended the lattice block concept to superalloy materials. After a series of casting iterations, the nickel-based superalloy Inconel 718 (IN 718, Inco Alloys International, Inc., Huntington, WV) was successfully cast into lattice block panels; this combination offers light weight combined with high strength, high stiffness, and elevated-temperature durability. For tests to evaluate casting quality and configuration merit, small structural compression and bend test specimens were machined from the 5- by 12- by 0.5-in. panels. Linear elastic finite element analyses were completed for several specimen layouts to predict material stresses and deflections under proposed test conditions. The structural specimens were then subjected to room-temperature static and cyclic loads in Glenn's Life Prediction Branch's material test machine. Surprisingly, the test results exceeded analytical predictions: plastic strains greater than 5 percent were obtained, and fatigue lives did not depreciate relative to the base material. These assets were due to the formation of plastic hinges and the redundancies inherent in lattice block construction, which were not considered in the simplified computer models. The fatigue testing proved the value of redundancies since specimen strength was maintained even after the fracture of one or two ligaments. This ongoing test program is planned to continue through high-temperature testing. Also scheduled for testing are IN 718 lattice block panels with integral face sheets, as well as specimens cast from a higher temperature alloy. The initial testing suggests the value of this technology for large panels under low and moderate pressure loadings and for high-risk, damage-tolerant structures. Potential aeropropulsion uses for lattice blocks include turbine-engine actuated panels, exhaust nozzle flaps, and side panel structures.

Krause, David L.↗
NASA NTRS1998

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind- tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/ Air Force Research Laboratory/ NASA/ Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials. Keywords: aeroelasticity, smart structures, piezoelectric actuators, active fiber composites, rotorcraft, buffet load alleviation, individual blade control, aeroservoelasticity, shape memory alloys, damping augmentation, piezoelectric power consumption

McGowan, Anna-Maria Rivas↗
NASA NTRS1997

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/Air Force Research Laboratory/NASA/Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials.

McGowan, Anna-Maria Rivas↗
NASA NTRS1962

A SURVEY OF RESEARCH ON THE STABILITY OF HYDROSTATICALLYLOADED SHELL STRUCTURES CONDUCTED AT THE DAVID TAYLOR MODEL BASIN

Experimental and theoretical studies have been carried out to investigate the stability of ring-stiffened cylinders and hemispherical shells under hydrostatic pressure. The use of accurately machined models has been found extremely valuable in improving the quality of experimental data, thereby permitting a more careful examination of theory. As a result, the effects of boundary conditions and other factors usually masked by the influence of structural imperfections have been clarified. So far these studies have caused the investigators to regard classical small-deflection theory with increasing confidence.

ROCKET NOZZLE↗
NASA NTRS2002

Purification of the small mechanosensitive channel of Escherichia coli (MscS): the subunit structure, conduction, and gating characteristics in liposomes

The small mechanosensitive channel, MscS, is a part of the turgor-driven solute efflux system that protects bacteria from lysis in the event of osmotic downshift. It has been identified in Escherichia coli as a product of the orphan yggB gene, now called mscS (Levina et al., 1999, EMBO J. 18:1730). Here I show that that the isolated 31-kDa MscS protein is sufficient to form a functional mechanosensitive channel gated directly by tension in the lipid bilayer. MscS-6His complexes purified in the presence of octylglucoside and lipids migrate in a high-resolution gel-filtration column as particles of approximately 200 kDa. Consistent with that, the protein cross-linking patterns predict a hexamer. The channel reconstituted in soybean asolectin liposomes was activated by pressures of 20-60 mm Hg and displayed the same asymmetric I-V curve and slight anionic preference as in situ. At the same time, the single-channel conductance is proportional to the buffer conductivity in a wide range of salt concentrations. The rate of channel activation in response to increasing pressure gradient across the patch was slower than the rate of closure in response to decreasing steps of pressure gradient. Therefore, the open probability curves were recorded with descending series of pressures. Determination of the curvature of patches by video imaging permitted measurements of the channel activity as a function of membrane tension (gamma). Po(gamma) curves had the midpoint at 5.5 +/- 0.1 dyne/cm and gave estimates for the energy of opening DeltaG = 11.4 +/- 0.5 kT, and the transition-related area change DeltaA = 8.4 +/- 0.4 nm(2) when fitted with a two-state Boltzmann model. The correspondence between channel properties in the native and reconstituted systems is discussed.

NASA Discipline Cell Biology↗
NASA NTRS2013

Method and apparatus for conducting structural health monitoring in a cryogenic, high vibration environment

Sensors affixed to various such structures, where the sensors can withstand, remain affixed, and operate while undergoing both cryogenic temperatures and high vibrations. In particular, piezoelectric single crystal transducers are utilized, and these sensors are coupled to the structure via a low temperature, heat cured epoxy. This allows the transducers to monitor the structure while the engine is operating, even despite the harsh operating conditions. Aspects of the invention thus allow for real time monitoring and analysis of structures that operate in conditions that previously did not permit such analysis. A further aspect of the invention relates to use of piezoelectric single crystal transducers. In particular, use of such transducers allows the same elements to be used as both sensors and actuators.

Qing, Xinlin↗
NASA NTRS2019

Magnetic Gears and Their Structural Limitations

Magnetic gears present significant structural design challenges, because metallic/electrically conductive structures are highly undesirable as they would lead to significant efficiency reductions. Additionally, most non-electrically conductive structural materials have low thermal conductivity, which makes cooling the gear difficult. These limitations are of particular significant in magnetic gear's modulator structures. NASA Glenn has shown that pole pieces on the order of 1 to 2 mm thick optimize magnetic gears specific torque. These thin pole pieces however see very large magnetic forces and modulator structural limitations prevent the use of magnetically optimum pole pieces. The best solution to this issue to date has been the use of carbon fiber retaining rings on the external surface of the modulator, however this solution increases ring modulator airgap, resulting in a torque reduction from the optimum design. The pole pieces are also the largest sources of losses in magnetic gears. Because the modulator is nestled between the ring and sun gear extraction of this heat is a difficult problem and the modulator structure has to be designed to dissipate this heat load. In the presentation I will present the design of NASA Glenn's 4th magnetic gear's modulator in detail that uses a combination of 3D fiber reinforced nylon, IM7 carbon fiber, and pitch base cn80 fiber to close both structurally and thermally.

Tallerico, Thomas↗
NASA NTRS2003

Experimental and Analytical Studies of Smart Morphing Structures Being Conducted

The development of morphing aeropropulsion structural components offers the potential to significantly improve the performance of existing aircraft engines through the introduction of new inherent capabilities for shape control, vibration damping, noise reduction, health monitoring, and flow manipulation. One of the key factors in the successful development of morphing structures is the maturation of smart materials technologies.

Lee, Ho-Jun↗
NASA NTRS2003

Assessment and Control of Spacecraft Charging Risks on the International Space Station

Electrical interactions between the F2 region ionospheric plasma and the 160V photovoltaic (PV) electrical power system on the International Space Station (ISS) can produce floating potentials (FP) on the ISS conducting structure of greater magnitude than are usually observed on spacecraft in low-Earth orbit. Flight through the geomagnetic field also causes magnetic induction charging of ISS conducting structure. Charging processes resulting from interaction of ISS with auroral electrons may also contribute to charging albeit rarely. The magnitude and frequency of occurrence of possibly hazardous charging events depends on the ISS assembly stage (six more 160V PV arrays will be added to ISS), ISS flight configuration, ISS position (latitude and longitude), and the natural variability in the ionospheric flight environment. At present, ISS is equipped with two plasma contactors designed to control ISS FP to within 40 volts of the ambient F2 plasma. The negative-polarity grounding scheme utilized in the ISS 160V power system leads, naturally, to negative values of ISS FP. A negative ISS structural FP leads to application of electrostatic fields across the dielectrics that separate conducting structure from the ambient F2 plasma, thereby enabling dielectric breakdown and arcing. Degradation of some thermal control coatings and noise in electrical systems can result. Continued review and evaluation of the putative charging hazards, as required by the ISS Program Office, revealed that ISS charging could produce a risk of electric shock to the ISS crew during extra vehicular activity. ISS charging risks are being evaluated in ongoing ISS charging measurements and analysis campaigns. The results of ISS charging measurements are combined with a recently developed detailed model of the ISS charging process and an extensive analysis of historical ionospheric variability data, to assess ISS charging risks using Probabilistic Risk Assessment (PRA) methods. The PRA analysis (estimated frequency of occurrence and severity of the charging hazards) are then used to select the hazard control strategy that provides the best overall safety and mission success environment for ISS and the ISS crew. This paper presents: 1) a summary of ISS spacecraft charging analysis, measurements, observations made to date, 2) plans for future ISS spacecraft charging measurement campaigns, and 3) a detailed discussion of the PRA strategy used to assess ISS spacecraft charging risks and select charging hazard control strategies

Koontz, Steve↗
NASA NTRS1999

Chip connectivity verification program

A method for testing electrical connectivity between conductive structures on a chip that is preferably layered with conductive and nonconductive layers. The method includes determining the layer on which each structure is located and defining the perimeter of each structure. Conductive layer connections between each of the layers are determined, and, for each structure, the points of intersection between the perimeter of that structure and the perimeter of each other structure on the chip are also determined. Finally, electrical connections between the structures are determined using the points of intersection and the conductive layer connections.

Riley, Josh↗
NASA NTRS2000

Thermally conductive support structure

A structure for supporting and at least transferring heat energy away from at least a first heat source interconnected thereto is disclosed. In one embodiment, the structure includes a deck member having a plurality of layers of thermally conductive fibers packed within a matrix material. Fibers of at least a first layer are orientable to transfer heat energy toward at least a first sidewall of the deck member, and fibers of at least a second layer are orientable about .+-.45.degree. relative to the fibers of the first layer to enhance the structural strength of the deck member. In another embodiment, fibers of at least a first layer of thermally conductive fibers of the deck member are orientable to transfer heat energy from a first heat source to a second, cooler heat source, both of which are interconnectable to the deck member, such that the first and second heat sources operate at substantially uniform temperatures. In this embodiment, fibers of at least a second layer of thermally conductive fibers are orientable about .+-.45.degree. relative to the fibers of the first layer to enhance the structural strength of the deck member. Fibers of at least a third layer of thermally conductive fibers are orientable substantially orthogonally relative to the fibers of the first layer to transfer heat energy away from at least the first heat source to at least a first sidewall of the deck member.

Herzl, Alfred↗
NASA NTRS1978

Effects of ultrathin oxides in conducting MIS structures on GaAs

Schottky barrier-type GaAs baseline devices (semiconductor surface etched and then immediately metalized) and GaAs conducting metal oxide-semiconductor devices are fabricated and characterized. The baseline surfaces (no purposeful oxide) are prepared by a basic or an acidic etch, while the surface for the MIS devices are prepared by oxidizing after the etch step. The metallizations used are thin-film Au, Ag, Pd, and Al. It is shown that the introduction of purposeful oxide into these Schottky barrier-type structures examined on n-type GaAs modifies the barrier formation, and that thin interfacial layers can modify barrier formation through trapping and perhaps chemical reactions. For Au- and Pd-devices, enhanced photovoltaic performance of the MIS configuration is due to increased barrier height.

Childs, R. B.↗
NASA NTRS2012

Performance Data Report: Space Medicine Division, Human Research Program, Behavioural Health and Performance Research Element

This report is the result of a collaborative effort between NASA?s Behavioral Health & Performance (BHP) Research and Operations Group to investigate and determine the availability of data pertaining to behavioral performance (and other pertinent variables) that have been collected by the laboratories at NASA?s Johnson Space Center. BHP?s Operations and Research groups collaborated to systematically identify what types of performance data are needed in relevant BHP performance domains and also to conduct structured interviews with NASA personnel to identify which data do or do not exist currently (and for instances where such data exist, to evaluate the type, quality, accessibility, and confidentiality of those data). The authors defined outcome categories of performance that encapsulate BHP performance domains, mapped BHP Research Risks and Gaps onto those performance outcome categories, and identified and prioritized indicators for each outcome category. The team identified key points of contact (subject matter experts [SMEs]) as potential interviewees, created a template for structured interview questions about sources and accessibility of performance data, and coordinated and conducted structured interviews with the SMEs. The methodology, results, and implications of this effort, as well as forward work needed, are discussed in this report.

Shea, Camille↗
NASA NTRS1996

Thermal and Structural Analysis Conducted on Hollow-Core Turbine Blade of the Space Shuttle Main Engine

Hot-section components of spacecraft engines are exposed to severe thermal-structural loading conditions, especially during the startup and shutdown portions of the engine cycle. For instance, the thermal transient during startup within the space shuttle main engine (SSME) can lead to a gas temperatures in excess of 3000 C, affecting the operating life of key components, such as the turbine blades. To improve the durability of these components and in particular the turbine blade, single crystal superalloys have been considered. PWA-1480, a nickel-base superalloy, has been used as the turbine blade material for the Alternate Turbopump Development (ATD) program for the SSME.

Source record↗
NASA NTRS1989

Induced emission of radiation from a large space-station-like structure in the ionosphere

Large conducting structures in the ionosphere may have currents flowing through them which close in the ionospheric plasma. These currents can arise either from current leakage from an onboard power distribution system or by being induced by the motional electric field. Associated with these currents will be broadband electromagnetic radiation in the Alfven and lower hybrid bands. The radiation impedance of this electromagnetic radiation is explored for a structure of space-station-like dimensions as a function of the geometry of the structure and the composition of the ionic environment. It is shown that modification of the collecting area of the structure and environment can be used to minimize the radiation impedance. For a space station, the radiated power will at most be of the order of watts, which does not represent a significant power loss. However, the radiation field will give rise to a substantial pollution of the electromagnetic spectrum in the vicinity of the space station. Design choices to minimize this interference are suggested.

Hastings, D. E.↗
NASA NTRS1990

Effects of regolith/megaregolith insulation on the cooling histories of differentiated asteroids

The cooling histories of differentiated asteroids are calculated employing a variety of thermal-conductivity structures to simulate the potential insulating effects of regolith and megaregolith layers on the cooling rate. It was found that a combination of relatively thick megaregolith and regolith can potentially reduce the core cooling rate by more than a factor of 10 below the rate predicted by models with conventional thermal conductivity structure. Thus, differences in cratering (regolith production) histories may have resulted in radically different cooling rates for asteroids of similar radius, or in similar cooling rates from asteroids of different radius.

Haack, Henning↗