Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “comminution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Wear Mechanism Analysis of a New Rotary Shear Biomass Comminution System

A new biomass comminution system, Crumbler rotary shear, was developed to process fuel-grade biomass. The rotary shear is more efficient than the traditional hammer mill in comminuting high-moisture biomass and producing more uniform particles with minimal fines. However, the milling unit experiences significant wear in processing dirty woodchips. This study investigated the wear mechanisms of the rotary shear system based on analysis of the minerals carried by woodchips and characterization of actual worn components. Abrasive wear was found to be the dominant effect, and localized adhesive wear (material transfer), microfracture (chipping), and plastic deformation were additional effects. Connections have been made between the wear progression of key cutting components and the particle size change of biomass extrinsic minerals. On the basis of the wear mechanism understanding, mitigations based on advanced tool materials and optimized tool geometric designs are being developed for improving the tool life and cutting efficiency.

09 BIOMASS FUELS↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, Part II: Representing interparticle comminution by K COMP

An applied and empirical compaction fracture resistance parameter, K COMP , was developed to represent the compression-induced interparticle-comminution response of granular brittle materials (e.g., ceramic or glass particles). The development of K COMP is an outcome from Part I of this three-paper series. The K COMP represents a continuum response of compaction fracture resistance and was adapted from established Griffith linear elastic fracture mechanics theory. From that, the K COMP relates macroscopically applied compressive stress to a corresponding inverse-square-root representative particle size, where the latter is estimated from an entire particle size distribution or specific surface area measurement. In conclusion, the K COMP value was not constant over a wide range of stresses for all examined brittle granular materials, and this is indicative of a change in the dominant mode of permanent deformation at higher compaction stresses.

brittle↗
DOE OSTI2022

Investigation of Cutter–Woodchip Contact Pressure in a New Biomass Comminution System

A Crumbler ® rotary shear system was recently developed to process fuel-grade woodchips into feedstocks having more uniform particle sizes for improved flowability and higher thermochemical output yield than a traditional hammer mill. It represents a significant innovation in the state of the art of biomass comminution equipment. However, the milling unit has experienced significant abrasive wear of the feeding teeth and cutters when processing hard and dusty feedstocks, such as logging residue and corn stover. Here, we present initial simulation results from a finite-element stress analysis of the rotary shear, which is used to investigate the dynamics of interaction between the cutters and woodchips. This is the first step for optimizing the cutter design to improve the system lifetime and processing efficiency, thus reducing downtime and improving overall productivity.

42 ENGINEERING↗
DOE OSTI2024

Predicting biomass comminution: Physical experiment, population balance model, and deep learning

An extended population balance model (PBM) and a deep learning-based enhanced deep neural operator (DNO+) model are introduced for predicting particle size distribution (PSD) of comminuted biomass through a large knife mill. Experimental tests using corn stalks with varied moisture contents, mill blade speeds, and discharge screen sizes are conducted to support model development. A novel mechanism in the extended PBM allows for including additional input parameters such as moisture content, which is not possible in the original PBM. The DNO+ model can include influencing factors of different data types such as moisture content and discharge screen size, which significantly extends the engineering applicability of the standard DNO model that only admits feed PSD and outcome PSD. Test results show that both models are remarkably accurate in the calibration or training parameter space and can be used as surrogate models to provide effective guidance for biomass preprocessing design.

09 BIOMASS FUELS↗
DOE OSTI2023

Contact pressure analysis to allow improved design for the clearing plate in a biomass comminution system

For biomass processing systems, feedstocks with small but equal sizes can improve flowability and thermochemical outputs. The Crumbler rotary shear system was designed to achieve such ideal feedstocks to reduce costs and energy throughout the biomass supply chain. Improving the wear resistance of major components in this system is important to decrease the cost. Accelerating the feedstock flow through the rotary shear machine plays an equivalent role of improving its efficiency. An analytical analysis and a finite-element analysis of the stationary clearing plate are presented in this work. Here, these tools are used to investigate the effect of contact surface curvature on the impact pressure. The optimized new clearing plate design is expected to improve the component’s lifetime and wood chips flowability. The field tests confirm that the trend of the new clearing plate design guided by FEA. The optimization method, model verification, and validation experience applied in this work can also be applied to other static components with similar simple contact wear problems.

09 BIOMASS FUELS↗
DOE OSTI2020

An Analytical Model of Erosive Wear of BioMass Comminution Components

An analytical erosion model that relates critical process parameters (speed and impingement angle) to critical material attributes of inorganic mineral species in feedstock (density, size, aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear in pretreatment milling operations. Results of the model were compared to experimental measurements of wear produced using the Accelerated Wear Test (AWT) rig at Idaho National Laboratory (INL). Results showed that there is good agreement between predicted and measured performance, and that a quality-by-design (QbD) tool can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

09 BIOMASS FUELS↗
DOE OSTI2021

An Abrasion Wear Model of Rotary Shear Comminution of Biomass Feedstock

The research team formulated a workable analytical abrasion model that relates critical rotary shear process parameters (shear geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) that enabled us to model the wear of shear cutters in a rotary shear milling system developed by Forest Concepts. We compared results of the model to experimental observations of the shape of rotary shear cutters used in a Forest Concept Crumbler® shear mill. Results showed good agreement between the predicted and measured shape of a worn cutter; thus, a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

42 ENGINEERING↗
DOE OSTI2024

Large-Volume Stimulation of Rock for Greatly Enhanced Fluids Recovery using Targeted Seismic-Assisted Hydraulic Fracturing (Final Technical Report)

This project has developed and demonstrated a new technology for large-volume and targeted comminution of rock in low permeability formations to enhance recovery from unconventional oil and gas (UOG) resources. The technology is based on a strategically designed interaction of multiple induced seismic pulses that assist the hydraulic fracturing process to enhance shear and multi-planar crack formation. This greatly increased rock stimulation, through bulk comminution, is expected to cause significant increase in permeability leading to enhancement of recovery factors for sub- surface fluids. The proposed technology is especially applicable for enhanced recovery in emerging UOG plays, such as ductile shales that are resistant to opening-mode fracturing by conventional hydraulic fracturing processes. The project combines an integrated experimental and computation approach to develop and demonstrate a modular technology that can be easily implement in the field to augment current practices. The effort integrates a fundamental scientific understanding of dynamic material response under constraint and damage-induced permeability and porosity enhancements at multiple length scales, along with models of comminution due to the local release of kinetic energy associated with high shear strain rate of dynamic deformation. The results will be validated through small-scale experiments and then implemented in a lab-scale field test to demonstrate the developed technology. The project involves collaboration between a solid mechanician, a materials scientist, and a petroleum engineering geo-mechanician. It builds on a successful history of success and collaboration that includes both fundamental scientific exploration and technology development.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Flowability of Crumbler Rotary Shear Size-Reduced Granular Biomass: An Experiment-Informed Modeling Study on the Angle of Repose

Biomass has potential as a carbon-neutral alternative to petroleum for chemical and energy products. However, complete replacement of fossil fuel is contingent upon efficient processes to eliminate undesirable characteristics of biomass, e.g., low bulk density, variability, and storage-induced quality problems. Mechanical size reduction via comminution is a processing operation to engineer favorable biomass flowability in handling. Crumbler rotary shear mill has been empirically demonstrated to produce more uniformly shaped particles with higher flowability than hammermilled biomass. This study combines modeling and experimentation to unveil fundamental understandings of the relation between granular particle characteristics and biomass flow behavior, which elucidate underlying mechanisms and guide selection of critical processing parameters. For this purpose, the impact of critical material attributes, including particle size (2–6 mm), particle shape (briquette, chip, clumped-sphere, cube, etc.), and surface roughness, on the angle of repose (AOR) of milled pine chips were investigated using discrete element method (DEM) simulations. Forest Concepts Crumbler rotary shear system is used to produce milled pine particles within the same size range considered in DEM simulations. AOR of different sets of these particles were measured experimentally to benchmark DEM results against experimental data. Specific energy consumption for the comminution of biomass with different particle size and moisture content are measured for technoeconomic analysis. Our results show that the smaller size (2 mm) of pine particle achieves better followability (i.e., smaller AOR) while the energy cost of comminution is significantly higher and bulk density is almost the same as the 6-mm pine particles. For the 2-mm particle size, Crumbles from veneer have better flow properties than Crumbles from chips. Contrarily, no significant difference was observed between the AOR of the two materials for the 6-mm particle size. Furthermore, from DEM simulations, mechanical interlocking between particles was found as a dominant factor in determining AOR of complex-shaped particles such as milled pine, which cannot be accurately captured by using simple particle shapes (e.g., mono-sphere) with a rolling resistance model. Conversely, clumped-sphere model alleviates this limitation without increasing computational cost significantly and can be used for accurate representation of biomass granular particles when simulating free-flow behavior.

09 BIOMASS FUELS↗
DOE OSTI2021

The mechanics of brittle granular materials with coevolving grain size and shape

The influence of particle shape on the mechanics of sand is widely recognized, especially in mineral processing and geomechanics. However, most existing continuum theories for engineering applications do not encompass the morphology of the grains and its evolution during comminution. Similarly, the relatively few engineering models accounting for grain-scale processes tend to idealize particles as spheres, with their diameters considered as the primary and sole geometric descriptor. This paper inspires a new generation of constitutive laws for crushable granular continua with arbitrary, yet evolving, particle morphology. We explore the idea of introducing multiple grain shape descriptors into Continuum Breakage Mechanics (CBM), a theory originally designed to track changes in particle size distributions during confined comminution. We incorporate the influence of these descriptors on the elastic strain energy potential and treat them as dissipative state variables. In analogy with the original CBM, and in light of evidence from extreme fragmentation in nature, the evolution of the additional shape descriptors is postulated to converge towards an attractor. Comparisons with laboratory experiments, discrete element analyses and particle-scale fracture models illustrate the encouraging performance of the theory. The theory provides insights into the feedback among particle shape, compressive yielding and inelastic deformation in crushable granular continua. These results inspire new questions that should guide future research into crushable granular systems using particle-scale imaging and computations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A nonlinear elasto-plastic bond model for the discrete element modeling of woody biomass particles

This work presents an experiment-informed, semi-empirical, elasto-plastic bond model for the discrete element modeling of woody biomass particles. The model renders nonlinear plastic deformation of materials when subjected to compression/tension, bending, and twisting, essential for accurately simulating the behavior of biomass in comminution. The model is implemented in an open-source DEM package LIGGGHTS and is assessed in a number of verification tests. The model is applied to simulate the fracturing test of notched loblolly pine blocks. Reduced bond strength is prescribed to the weak planes along the growth rings. It is found that the square-root formulation for describing the elasto-plastic normal bond contact delivers the best agreement with the experimental data over its linear and quadratic counterparts. Furthermore, the model predicts a strong anisotropic behavior of wood blocks with regard to the grain orientations, indicating that the cutting angle should be an important attribute for the optimization of biomass comminution.

42 ENGINEERING↗
DOE OSTI2020

Method and system for preparing polycrystalline group III metal nitride

A process of preparing polycrystalline group III nitride chunks comprising the steps of (a) placing a group III metal inside a source chamber; (b) flowing a halogen-containing gas over the group III metal to form a group III metal halide; (c) contacting the group III metal halide with a nitrogen-containing gas in a deposition chamber containing a foil, the foil comprising at least one of Mo, W, Ta, Pd, Pt, Ir, or Re; (d) forming a polycrystalline group III nitride layer on the foil within the deposition chamber; (e) removing the polycrystalline group III nitride layer from the foil; and (f) comminuting the polycrystalline group III nitride layer to form the polycrystalline group III nitride chunks, wherein the removing and the comminuting are performed in any order or simultaneously.

36 MATERIALS SCIENCE↗
DOE OSTI2026

An Anisotropic Yield and Damage Material Model to Improve the Contact Pressure Analysis in a Biomass Shredding System

Size reduction systems used in biomass processing break biomass into smaller pieces by utilizing the kinetic energy from the sharp rotating blades. Abrasive and/or erosive wear caused by biomass comminution results in blade wear of the sharp edged cutters, deteriorating the process efficiency. Here, this study aims to optimize the blade design and improve the system efficiency by attempting to understand the interactions between the blades and biomass particles. Since real-time monitoring of these interactions is impractical during operation, mechanical simulations offer a viable alternative for investigating the shredding process. Yet, the irregular geometry and complex mechanical properties of biomass—such as the anisotropic nature of woodchips and their nonlinear fracture behavior—pose significant challenges for accurately simulating contact pressure. In this work an anisotropic yield material model, along with a damage initiation and evolution function, is applied to the woodchip particle to study the contact pressure on shredder blade, offering a scientific basis for improved blade design and process efficiency. This approach can be extended to other biomass processing systems with similar anisotropic feedstocks, making it a valuable tool for advancing sustainable biomass utilization.

09 - BIOMASS FUELS↗
DOE OSTI2023

An experiment-informed discrete element modelling study of knife milling for flexural biomass feedstocks

A discrete element method (DEM) based approach is used to study the relationships between material attributes (MAs), processing parameters (PPs), and quality attributes (QAs) for the knife milling of maize stalks. An approximate DEM shape model was conceptualized based on real maize stalks and calibrated based on experimental bending test data for flexural properties (elastic bending stiffness, elastic bending angle limit, elastoplastic ratio, etc.). DEM simulations of maize stalk comminution in a Jordan Reduction Solutions (“JRS”) knife mill were performed to investigate the relationships between the MAs (maize stalk size and breakage stress limit), PPs (impeller rotational speed), and QAs (mass throughput and output particle size distribution (PSD)). The DEM results suggest that stalk length has little influence on mass throughput and PSD, whilst stalks with larger cross sections tend to generate larger sizes of milled particles given the same breakage stress limit. Both the DEM and experimental results show that faster impeller rotation (or higher power) does not necessarily generate higher throughput or smaller output PSD, especially for maize stalks of higher breakage stress limit. The correlations between these MAs, PPs and QAs are found highly stochastic, though breakage stress limit dictates mass throughput, regardless of stalk size. The DEM-predicted output particle size tended to match the experimental data with coarse PSDs based on sieve size but showed weakened fidelity with finer material, indicating the potential for further model improvement.

09 BIOMASS FUELS↗
DOE OSTI2025

On the bulk compaction of brittle granular materials, Part III: Brittle‐to‐ductile transition and yield strength

A new and simple method is presented that enables the estimation of the yield strength (σ y ) of brittle materials (e.g., ceramics, glasses). It results from the combination of sufficiently high-stress compaction of their granular form, postmortem analysis of the crushed particles to identify the critical particle size corresponding to their brittle-to-ductile transition, and the use of a developed and simple analytical expression. Here, this method was an outcome from Part I of this three-paper series. To execute it, a granular brittle material is compacted to a sufficiently high stress, whereby the acting comminution produces both a fraction of particles having a sufficiently small size formed by ductile or plastic-like deformation and a remaining fraction of larger particles formed from brittle fracture. Postmortem microscopy is then used to identify the smallest particle size whose morphology indicates it formed from brittle fracture (d B2D ). The brittle material's σ y can then be estimated using a combination of the d B2D , Kendall's and Griffith's theories, a priori knowledge of the material's fracture toughness (K Ic ), and a fracture mechanics shape factor constant (Y) using σ y = √((32 π K Ic 2 )/(3 Y 2 d B2D )). The method's development and its use to estimate σ y for several vitreous silicates, α-quartzes, and NaCl are provided.

Compaction↗
DOE OSTI2020

Identification of Critical Process Parameters for Knife Milling and Alternative Communication Strategies

An assessment of knife milling operations was performed to identify parameters that require consideration to model wear and degradation of knife blades. A quality-by-design (QbD) paradigm was followed to identify material and feedstock attributes, and processing parameters that impact the quality attributes of the blades used in the comminution of biomass into forms compatible with downstream operations. Based on analytical and experimental observations of knife and tool wear, a QbD model is proposed that considers three wear mechanisms (erosion, abrasion, and gouging) to predict volumetric wear of knife blades and sharpness. These factors, if properly applied, provide a science-based approach to predict the mechanical efficiency of the mill as a function of feedstock properties, knife blade material properties, and processing parameters (feed rate, speed, and design parameters).

09 BIOMASS FUELS↗
DOE OSTI2022

BETO 2021 Peer Review - FCIC Task 5 - Preprocessing

In the study of feedstock variability, this presentation specifically looks at preprocessing processes that will created well-defined and homogenous feedstock from variable biomass resources, in the quest to produce homogeneous intermediates that will be converted into market-ready products. The objective of this stage of the project is to develop science-based design and operation principles informed by TEA/LCA that result in predictable, reliable, and scalable performance of preprocessing unit operations (comminution, fractionation, deconstruction, and real-time imaging).

biomass↗